Search Documents

By Klau Meyer

"At Teck-Corona Operating Corporation's David Bell Mine, a successful water quality management strategy has been established. This resulted from the development and application of process technology, allowing year round discharge of an effluent exceeding the chemical and biological standards set by the Ministry of Environment. This strategy aims at minimizing contaminant levels of effluents through optimization of reagent selection and reduction of effluent volumes through maximizing reclaim water usage. Concentrator and effluent treatment plant operating practices, process chemistry and the results of the water quality management strategy are reviewed.IntroductionThe David Bell Mine is located in the Hemlo gold camp 42 km east of Marathon, Ontario. The concentrator has a design throughput of 1000 tonnes per day. The processing of the run of mine ore ( - 15cm) involves the following unit operations: grinding in a semi-autogenous mill followed by a ball mill, thickening, pre-oxidation , cyanidation, and carbon-in-pulp gold recovery followed by electrowinning and refining.The David Bell Mine water quality management strategy is composed of the following items (Goodfellow and Meyer, 1991):• natural destruction of cyanide contained in the tailing water in a large shallow tailing pond ;• preliminary treatment of reclaim water in the grinding circuit for cyanide and heavy metal removal;• pre-oxidation of sulphide minerals in pipe reactors to reduce cyanide consumption using pure oxygen;• pH control in the grinding, pre-aeration and leach circuits to minimize the dissolution of stibnite while maximizing gold recovery; • close control of cyanide addition rates to the leach circuit to maintain the lowest possible levels;• a carbon column for gold recovery;• an effluent treatment plant for antimony and heavy metal removal; and• the use of final treated effluent for industrial water underground to minimize fresh water consumption."

Jan 1, 1992

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By Margarete Kalin

Mine Waste Management ?Reduction of Sulphideoxidation or inhibiting weathering of rocks Geologist - broken or ground rocks Hydrologist - sources of contaminants Mining engineer - waste sites Consulting companies - income units People - Ugly, bad, dead Ecological Engineer Landscapes which contain building blocks of an emerging ecosyste

May 1, 2013

By Bruce W. Smith

Non-contacting, radioisotope density and level gauges are discussed. The characteristics of the more commonly used isotopes, the techniques of detection and the methods of presenting information are reviewed. The gauge parameters of accuracy, response time and long-term stability are tabulated with reference to calibration techniques and operating requirements. Automatic control systems, both pneumatic and electrical, are used in conjunction with density gauges on filter feeds, and in thickener underflow and heavy media processes. These systems are described. Procedures for installation, start-up and operator training are outlined, along with considerations of preventative maintenance and service requirements. Typical gauge system costs, including capital expenditure, installation, start-up and service, are presented, wherever possible, in order to provide a basis of comparison with more conventional systems.

Jan 1, 1964

By P. Cleyle, J. H. Masliyah, R. S. Chow, Z. H. Xu, Z. A. Zhou

Bubble nucleation in water under dynamic conditions was investigated using an autoclave at an air saturation pressure of 7 atm. Agitation during air saturation of water was found to be crucial in enhancing tiny bubble formation. More bubbles nucleated on hydrophobic surfaces at a higher agitation rate, due to cavity formation by the more intense hydrodynamic conditions. Flotation recovery of bitumen from oil sands demonstrated a significant role of bubbles nucleated in water: more than 50-170% increase in bitumen recovery from different oil sands was obtained by using air supersaturated than the regular water.

Jan 1, 2009

By P. D. Hodgson, G. L. Kelly, H. Beladi

"The formation of ultrafine ferrite by strain induced transformation is assessed using rolling and hot torsion experiments. These experiments are used to examine the impact of thermomechanical processing conditions and steel chemistry on strain induced austenite to ferrite transformation and the formation of ultrafine ferrite. The critical strain for dynamic strain induced transformation increased with increasing carbon equivalence, deformation temperature and austenite grain size. The deformation structure in the austenite grains changes with the thermomechanical processing conditions.Drawing on these results and the current literature, the important factors for the production of ultrafine ferrite are described and a mechanism proposed."

Jan 1, 2004

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By B. R. Casement

"Managing safety on the basis of after-the-fact reaction to accidents, can never be more than partially successful. Injuries will occur as long as the underlying potential for them still exists. Unless unsafe actions and conditions are systematically decreased, no program can have more than a short-term success.The pro-active Bullmoose loss control process, instead, focusses on heightening awareness of work habits, to prevent incidents by reducing their potential.Any safety program will be doomed to failure if the development of safe work habits depends on the safety supervisor or a safety committee. At Bullmoose the focus is on the critical actions out of which losses emerge. The successful application of performance-related feedback is achieved by taking safety, health, and environmental concerns into consideration on every level, and, by doing the right thing in every job done.What is an Exceptional Loss Control Program?If an accident in an organization creates a flurry of interest, resulting in ""cracking down"" on violations for a short period of time then an ""exceptional"" loss control program exists. Unfortunately, exceptional here does not refer to the effectiveness of quality of the program but to the fact that the organization is managing loss control by exception. The degree of management attention in an ""exceptional"" safety program varies over a period of time, remaining low as long as the rate of losses stays within management's acceptable control limit (Fig. I). When the losses rise above this, management becomes motivated to begin ""exceptional"" efforts to manage losses. When the rate falls again to within the accepted limit, efforts to control losses take a back seat.Such a strategy guarantees that losses will be tolerated or ignored as long as the actual rate is below the acceptable limit. Simply to lower the limit would not reduce losses, but would result in an increased number of flurries of management attention to loss control. This ""on-again, off-again"" style of management teaches supervisors and others that basic loss control is not as important as are statistics."

Jan 1, 1993

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By D. Perednis

Fuel cells with thin samaria-doped ceria (SDC) electrolyte films deposited onto an anode support using spray pyrolysis were fabricated. The SDC films were deposited onto porous NiO-YSZ substrates at deposition temperatures between 400°C and 450°C. The influence of process parameters such as deposition temperature, flow rate, type of salt and salt concentration on the quality of the film was studied. A smooth dense film was successfully deposited using the precursor cerium ammonium nitrate and samarium nitrate dissolved in butyl carbitol (33.3 vol.%), 2-methoxy-l-propanol (33.3 vol.%), and ethanol (33.3 vol.%) solvent mixture. A deposition rate of 125 nm/h was achieved.

Jan 1, 2005

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

By H. Tan

The effect of carbonaceous matter on gold extraction was investigated in cyanide systems with pure gold as well as pre-robbing sulfide gold ores. Auger studies demonstrated that the carbonaceous matter preferentially smeared on iron sulfide rather than aluminosilicate surfaces during wet or dry grinding. During mechanically mixed leaching, coating of sulfides and silicates and stripping of carbonaceous matter occurred simultaneously. TEM and XPS studies indicated preferential coating in the form of elemental (graphitic) carbon at the edges and the defect sites of particles. Interestingly, carbonaceous matter extracted from the gold ore was predominantly graphite and not preg-robbing in a solution with a high KCN concentration. However, the carbonaceous coating had a significantly detrimental effect on gold dissolution when gold was pre-ground with the gold ore. Artificial coating on gold surfaces with the natural carbonaceous matter from the ore was also found to substantially retard gold dissolution. With the addition of the natural carbonaceous matter from the gold ore, gold extraction from two non preg-robbing sulfide gold ores was inhibited owing to carbonaceous coating. The presence of carbonaceous matter significantly reduced the current density for gold oxidation and increased the current density for pyrite oxidation. This could explain the fact that carbonaceous coating hindered gold dissolution while enhanced sulfide preg-robbing.

Jan 1, 2005

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By S. F. Guo, Z. F. Zhan, X. L. Huang, Y. Zou, S. W. Qi

"FLAC3D is an important numerical analysis software to study dynamic response of rock slope. In application of the program, the common issues such as absorbing boundary and the method to apply wave have been well studied. However, effects of model mesh size, damping and width of slope are still unknown. In order to make the result more convictive, this article has discussed the above issues systematically. It found that when the maximum mesh size is smaller than 1/10~1/8 of the smallest wavelength, the mesh size is smaller, the computational accuracy is higher. Meanwhile, values of damping and width of slope have no effect on the result. Additional, results of FLAC3D modeling on wave transmission across rock joints agree well with analytical solutions, so it has verified the capability and accuracy of FLAC3D on dynamic response of rock slope.INTRODUCTIONChina is a mountainous country accompanied with many earthquakes. Thousands of geological disasters are triggered by the Wenchuan Earthquake in Sichuan Province, and the majority of the disasters are landslides induced (Xu et al., 2009). Meanwhile, the paper (Li et al., 2003) points out five significant issues about dynamic loading in the area of geotechnical engineering, which includes the study of rock slope stability under earthquakes, and the dynamic response of rock slopes is one of its important study issues."

Jan 1, 2015

By R. R. Potter

"IntroductionAlthough iron formations were recognized in western New Brunswick about 1820, commercial production was not achieved until 1848. The Jacksonville deposits near Wood stock were developed first, and ore was treated at a blast furnace constructed 5 km to the southeast on the Saint John River. Several charcoal burners were also constructed. Pig iron was produced sporadically until 1884, when operations were finally suspended. There was little further interest in the area until 1953, when Stratmat Ltd. initiated an ambitious exploration program. At the same time, the company carried out research on an electric-reduction process to produce metallic iron and ferromanganese. The technical feasibility of this process (Udy process) was confirmed, however the high energy costs were prohibitive and work ceased in 1957. Some metallurgical research was carried out by Mandate Refining Ltd. about 1970 and more recently by the New Brunswick Research and Productivity Council.The Years Prior to 1848New Brunswick became a separate province in 1784, shortly after the influx of a large number of Loyalists from the United States. Man y of these people sett led along the Saint John River, including the area of excellent farmland near the present town of Woodstock.There were indication s that some of these earl y settlers recognized iron formations in the vicinity of Woodstock about 1820, however the nature of the deposits was not known until 836 when Dr. C.T. Jackson, a geologist commissioned by the Stat e of Maine, investigated the mineral potential of the area. Jackson (1836) described the ""ore"" as compact red hematite yielding 44 per cent pure metallic iron, and suggested that sizable tonnages may be present. It was about this time that an extensive limonite deposit was found in north-central Maine, near Mt. Katahdin. Other iron deposits were found in the Nictaux area of Nova Scotia, and a few years later at Londonderry."

Jan 1, 1983

By D. Runnels, A. Allaire, J. Torrealba-Vargas

Data mining and modelling of operational data involves the discovery of patterns in large datasets for future use in benchmarking and plant optimization. The modern pattern of discovery in large data sets involves statistical techniques, machine learning and new visualization tools. Former examples of data mining are revisited and presented in this document. INTRODUCTION A network of enthusiastic and active professionals is currently developing and maintaining several open source statistical software tools (packages) for data analysis (example Rstudio, Orange, Spyder, etc.). The advantages of the open source software philosophy are the fast development and testing of the solutions presented to the community. Books and support are available for each software application. Since each modern work activity generates massive amounts of data, it is attractive to learn and test those available tools considering that we are at the door of the new work revolution coined as “Mine 4.0”. Data mining involves collecting large datasets, the preparation and cleaning of a dataset (term named data wrangling), the uploading of the data to a database program capable of handling big datasets, the development of prediction models and the presentation of the results. Machine learning techniques help to develop mathematical models and algorithms that could be used to improve the performance on a specific task. Mine operations are producing an incredible amount of data each day and the need to analyze those results seems to be impossible due to the lack of time, as well as the lack of skills to investigate the data collected. If we add to this the traditional habit of working in silos, an additional challenge is to consolidate databases from different departments in search of trends that could help to optimize production.

Jan 1, 2019

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004