Search Documents

By R. B. Casault, J. D. Boyd, D. R. Bell

"Full-scale sections of three different types of Grade 483 line pipe have been evaluated extensively. The variations in chemical composition, optical microstructure, tensile properties, hardness and Charpy impact toughness with specimen orientation and location were determined. Significant variations in several properties, notably Charpy shelf energy, impact transition temperature, inclusion content and ferrite grain size, were observed for different locations in the pipes. The results indicate that current specifications call for test samples for the most conservative locations, except for impact tests. Minimum Charpy impact values generally occur at the II2-width location, which may be a more appropriate specified test location than the present I/4-width location. The anisotropy of impact toughness, and the importance of low sulphur content and inclusion shape control for adequate toughness in the transverse/rolling-direction orientation were demonstrated. The orientation of impact specimens is critical for spiral-weld pipe, and the current specification test is non-conservative in that it can give results which are two to three times higher than the minimum value for the steel.IntroductionThis report presents the results of an extensive metallurgical evaluation of three different Grade 483 line-pipe steels. The sample material came from full-scale sections of line pipe, which represented current commercial practice at the time of manufacture (1975-1977). Since then, significant improvements have been made in the manufacturers' procedures for producing skelp and pipe, and the line-pipe specifications have been revised. Hence, the information in this report is dated in terms of current design, but it is unique and significant in several respects:"

Jan 1, 1982

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By D. L. Griffith

THE realization by metallurgists of the important effect that traces of impurity may have upon the properties of a metal, and their steady demand for purer and still purer metals, have made the special cools for 'trace' analysis of increasing value. In the United States at least, spectrographic analysis is becoming the standard method for determining the impurities in zinc die-casting alloys. The Hudson Bay Mining and Smelting Company, as a producer of virtually pure zinc, uses the spectrograph to control the purity of its products, and-as the electrolytic method is employed here-to control both the impurities in the electrolyte and those 'trace' elements, which, while they do not contaminate the zinc, have a great effect on the plating efficiency. The general plan of the laboratory is shown in Figure l; the housing for air purification, which is on the roof, is indicated by broken lines. One of the chief factors affecting the layout was the easy way in which a spectrographic assay can be spoiled by contamination. To minimize the quantity of dust tracked in, the laboratory was made separate from the general research laboratories, and an office was placed between the two. This arrangement has its drawback because of the traffic through the office, but it has effectively cut down dust. For similar reasons, the available space was subdivided into a number of small rooms, and the air currents in the laboratory were so arranged that dust would be carried where it would do least harm. Air is drawn in at the roof over a 50-kilowatt bank of Calrod heaters, through Annis air filters, by a No. 4 Sirocco fan. Most of it is forced into the spectrograph room, but some goes to the office and darkroom. The air flow is from the spectrograph room, through the plate-measuring room, into the chemical laboratory, where it is exhausted by a No. 1% Sirocco fan on the fume hood. Air can also re-circulate from the plate-measuring room back to the heater. The arrangement is such that the air in the laboratory is maintained at higher pressure than the outside air; consequently, no dirt enters through cracks about the windows and doors. A thermo-regulator holds the temperature constant within one or two degrees; only on the hottest days in summer does the temperature rise enough to affect the focus of the instrument.

Jan 1, 1940

By S. Harshaw, C. Doyle, A. E. M. Warner, D. Stremlaw

"In the Utility Nickel furnaces, the hearth and sidewalls are lined with high-Al2O3 bricks. During charging and thermal cycling (more so as the linings on these reverberatory furnaces age), pieces of brick spall or abrade from the refractory and collect on the top of the bath. These pieces are removed using a non-corrosive slag toward the end of the heat when the bath temperature is ~1600°C.This benign liquid can be generated by two methods. First and most obvious, suitable ingredients can be pre-mixed so that the flux (flux A) is isochemical with the non-corrosive slag. All that is needed to produce this targetted slag is heat. Second, in other proportions (flux B), the pre-mixed ingredients generate a corrosive slag that melts completely at -1200 °C and corrodes some but not all of the brick particles on the bath surface. As the reaction progresses, the slag changes composition eventually attaining the targetted benign composition. Using this option, additions are monitored to avoid overfluxing. In both cases, the generated slag/brick mixture can then be rabbled from the furnace. This practice has been successfully used for over two years and has been a factor in extending Utility Nickel furnace life to its current levels (about25% increase)."

Jan 1, 1993

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985

By P. Hanniala, S. Harkki, B. Andersson

"The Outokumpu Flash Smelting Process was put into commercial operation in 1949. The original process was based on the use of preheated air. The adoption of oxygen enrichment of the flash smelting process air in 1971 was a crucial improvement, especially for smelter capacity. Oxygen use according to the Outokumpu method means selection of the most suitable oxygen content for the process air on the basis of the concentrate composition, capacity and matte grade. The furnace is not bound to only one fixed degree of process air oxygen enrichment; the oxygen content may vary from 21% to 100%.The degree of oxygen enrichment and the matte grade are the most important process parameters in reducing the operating costs of the whole system, including smelting, converting and acid production. Raising the matte grade allows more efficient use of the reaction heat in the smelting stage. Sulphur is recovered in a high-strength, constant-flow gas stream. The blowing time in the converters is reduced considerably.Oxygen enrichment and high matte grade improve the energy efficiency of the plant complex as long as the surplus heat from the system is not wasted. When the operating costs and investment expenditure of the total plant complex are taken into account, a reasonably high degree of oxygen enrichment (35-80°/0) is the best alternative in practice. Existing operating smelters have achieved single-stream thoughputs of over one million t/yr of concentrates.HistoryLocal capital and operating costs as well as lower energy consumption per unit of metal produced are now the crucial factors in determining the choice of process. In the late I940s, the same reasons prompted Outokumpu to develop the original flash smelting process in Finland. Between 1900 and 1940, very few technical changes in pyrometallurgical copper production took place. However, the commercial use of the flash smelting technique began a new era in metal extraction from sulphide concentrates. The characteristic feature of the method is that the concentrate is smelted in suspension: this offers the most favourable conditions for heat and mass transfer, and thus high reaction velocities. Outokumpu was the first to exploit the known advantages of flash smelting in a commercial installation at Harjavalta in 1949."

Jan 1, 1982

By J. A. E. Bell

"Inco has shifted part of its traditional extractive research effort at its J..Roy Gordon Research Laboratory in Mississauga toward new, value-added products. Most of the effort is being expended on new Ni powders for batteries and new Ni-coated products which will be produced in Inco&apos;s carbonyl nickel refineries. New products under development are Ni-coated powders, Ni-coated fibres and ultra-fine Ni powders. Other new products for advanced material applications include controlled expansion composites, NiGOLD strip, Thermal barrier coatings on Inco alloys, and plasma coatings.Research and Corporate Strategic ThrustsThe newest strategic thru st of the company is to increase the value of the primary metal products. These new products are to be in addition to any new alloys or downstream alloy fabrication.Historically Inco has had the highest research expenditures in the extractive metallurgy field in North America. This has resulted in many new processes including flash smelting , matte separation, fluid bed roasting, pressure carbonyl refining and cobalt electrowinning which have contributed to establishing Inco as the lowest cost nickel producer. The recession of the 1980s caused a restructuring of Inco research and corporate goals .As shown in Figure I, from 1975-1982, i.e. pre-recession, Inco spent around 33 million dollars per year on research. Some 48070 of that sum was spent in Corporate Laboratories in Sterling Forest in the United States and in the United Kingdom , mostly on alloy associated research. A further 10% was spent on alloy research at the alloy production facilities in Hunting- ton, West Virginia, and Birmingham and Hereford in the United Kingdom. On extractive research, 13% was spent by process technology groups at the plant s, 20% at the pilot plants in Port Colborne and 9% at the J. Roy Gordon Research laboratory.The relative research expenditures (Fig. 2) have decreased so that today they are at the same level as 1975-80. The research as a per cent of sales has been cut from 2.2% to 1.2% of normalized sales. A normalized sale price of $4.00/lb Ni was used in the 1988 figures. This was partly achieved by closing Corporate Laboratories. Most of the essential alloy research was moved to producing plants and total alloy research is now 27%.A new thrust initiated in the 80s was mining research which now accounts for 20% of research expenditures. Over a period of the past five years this research has doubled the mining productivity in Inco. The pilot plant expenditures have been cut in half. One entire research station at Port Colborne was converted into a platinum group metals intermediate refinery. The decrease in pilot plant expenditures has been compensated by full scale plant trials devoted to the S02 abatement program at Sudbury."

Jan 1, 1990

Adsorption of guar gum was investigated on model minerals typically found in water-insoluble slimes of potash ores. The ionic strength of the adsorption mixtures was varied from distilled water to saturated NaC1 and KC1. The tests were also performed using a saturated brine. The adsorption density of guar gum on illite, dolomite, and kaolinite was found to be not only a function of total ionic strength but also of the type of electrolyte present in solution. Generally, the adsorption of the polymer on the clay minerals was higher in KC1 solutions than in NaCI, but the differences gradually disappeared when the electrolyte concentration approached saturation. The results were analyzed in terms of chaotropic (K ) or kosmotropic (Na&apos;) properties of background counter-ions and their different behaviors at the hydrated mineral-water interface. Guar gum adsorption on dolomite was related to the presence of calcium and magnesium sites on the mineral surface, and to the cis-configuration of OH groups of mannose units. Based on viscosity measurements, it was suggested that guar gum macromolecules form entanglements in NaCI solutions (and distilled water), but individual molecules exist in KC1 solutions thus creating different modes of adsorption of guar gum from concentrated NaCl and KCl solutions.

Jan 1, 2006

By J. -C. Sztuke, M. Cao

ABSTRACT Wash water and polyethylene oxide (PEO) were used in the flotation of quartz and coal. Wash water decreased entrainment of –15 µm quartz. The optimum superficial wash water rate was 0.05 cm/s. PEO also lowered entrainment. The combination of wash water and PEO led to a slight further reduction in entrainment. For 1:1 mixtures of –15 µm quartz and –300 µm oxidized coal, the combined use of wash water (0.05 cm/s) and PEO increased the separation efficiency from approximately 30% to > 70%, whereas wash water alone at 0.05 cm/s did not lead to a discernible increase.

Jan 1, 2014

By Zhiwei Wang, Chunsheng Qiao

"Aiming at the problems of the existing calculation methods for the support pressures of shallow tunnels in layered jointed rock strata, by using OAT (orthogonal array testing strategy) and DEM (distinct element method), 12 influencing factors including the thickness of the weathered overburden, and the states of the rock joints were considered. Then, the classification of the loosening zone was analysized. On this basis, by using the DEA (data envelopment analysis) theory, quantitative analysis on the influencing factors was conducted. By analyzing the influence of the key factors, a prediction formula of the boundary of the ringent trumpet-shaped loosening zone was established. According to principles of stress transformation, the formula of support pressures of the loosening zone which could considering the key factors were deduced. Finally, a practical case was introduced and studied to verify the proposed method.INTRODUCTIONIn recent years, various urban subway tunnels are increasingly carried out through jointed rock strata in many cities. Rock masses are discontinuous mediums with fissures, fractures, joints, bedding planes, and faults. The frequency of joints, their orientation with respect to the engineering structures, and the roughness of the joint have a significant importance from the stability point of view. However, there is a lack of understanding about the influence of the joints on the stability of tunnels. Therefore, how to measure the degree of the joints’ influence is a problem that needs to be solved.For the calculation of the support pressures, until now, many research results were focused on soil ground (Bierbäumer 1913; Terzaghi, 1943; Peck, 1969; Sabatini et al., 1999). In terms of site tests and model indoor tests, by measuring strut loads and calculating earth pressure based on strut spacing, the results proposed by Peck (1969) and Tschebotarioff (1973) have been widely used in practice for designing excavation support systems under sand (drained) and clay (undrained) soil conditions. Note that, it is unclear whether these findings could be extended to rock strata. For numerical simulations, how to simulate the states of the rock joints is a key problem that needs to be solved."

Jan 1, 2015

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By D. Tao

The adverse effects of clay particles on coal and mineral processing processes such as gravity separation, flotation, filtration, and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed largely to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of clay binding agents developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical and column flotation tests were carried out using coal and potash samples. Process parameters investigated include slurry solids percentage, impeller rotation speed, binder dosage, collector dosage, etc. Flotation results show that use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time was about 1 lb/t and 0.5-1 min, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Jan 1, 2006

By D. A. Bordin, C. J. Newman, R. J. St. Eloi

"The requirements for a metallurgical acid plant treating smelter gases are both unique and demanding in terms of sulphur dioxide treatment and emission control. Since start up in 1981, the copper smelter at the Kidd Creek Division of Falconbridge Limited has undergone several major expansions. The expansion and modification of the acid plant has been an integral part of this process. Both production demands and government regulations dictate that this metallurgical acid plant be unique in terms of operating flexibility. The variable capacity to treat a wide range of sulphur dioxide concentrations, and the operating flexibility to control emissions are the topics of this paper.INTRODUCTIONThe Kidd Creek Division of Falconbridge Limitied is a base metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April, 1964. Mining operations began in 1966 with a 9000 tonne per day concentrator coming on stream in November of that year. In April 1972, a 108 000 tonne per year zinc plant was commissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 tonnes of ore per day . To expand zinc production, the world&apos;s second installation of the Cominco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 125 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No.3 tankhouse technology for the copper refinery.The smelter, which uses the Mitsubishi Continuous Smelting Process for the continuous production of blister copper from concentrate, went on line in June 1981. It has been expanded from its original capacity of 60 000 tonnes to 100 000 tonnes per year of copper.From the very early design stages for the metallurgical complex, the company had adopted a policy of constructing and operating modern plants which would meet existing and anticipated environmental standards. With this in mind, the decision was made to utilize the proven technology of fixing sulphur dioxide emissions, in the form of sulphuric acid. A 636 tonne per day single absorption contact acid plant was built to serve the zinc plant in 1972. In 1981, an 883 tonne per day double absorption contact plant was built to serve the needs of the copper smelter. The copper smelter acid plant has since been expanded to a design capacity of 1692 tonnes per day and it is the main focus of this paper."

Jan 1, 1989

By H. L. Cheng, C. H. B. Leitch, C. T. Hood, A. J. Sinclair

"Epithermal Zn-Pb-Cu-Ag-Au quartz-carbonate-barite veins at the Silver Queen mine near Owen Lake, west-central British Columbia, are hosted by Late Cretaceous Tip Top Hill andesitic volcanic rocks. The veins form a rectilinear northwest-northeast pattern that differs slightly from regional structural trends. The main northwest-trending veins are oriented very close to the trend of regional northwest faults, but the crossing veins tend to be more east-north-easterly (070 degrees)compared to a regional north-easterly trend (040 degrees). The character of the veins suggests they are extensional features formed by dextral slip related to Paleogene oblique subduction, or intrusion of magma at depth, or both.In detailed exploration at the mine, the veins cannot be modelled as simple tabular sheet-like bodies. Instead, they are complex structures that divide and rejoin, forming multiple veins or stringers, or are found in shear zones as replacement features with quartzsericite- clay-carbonate-pyrite alteration haloes of variable width that make definition of vein margins and correlation from hole to hole ambiguous. In addition, individual veins within each of the main structures have en echelon characterboth along strike and down dip.Geological and assay data must be carefully studied to define the margins of these complex veins before any estimation of ore reserves may be made. Where multiple veins occur in a section, ore/gangue mineralogy, assays, character of wallrock alteration, and thickness of vein and mineralized hangingwall, median and footwall zones must be used to evaluate continuity of mineralized structures. Well-defined sections are projected into areas of increasing complexity. Once the vein boundaries are defined, metal concentrations, important metal ratios(Au/Ag, Pb/Zn, Cu/Zn), and true thicknesses of the vein provide the basic data for reliable ore reserve estimation."

Jan 1, 1991

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River &apos;C&apos; Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By Gerhard Heinrich

"The composition and the possible utilization of a slag sample from a nickel smelter operation in the Sudbury district were investigated. The sample containing 0.136% Ni, 0.10% Co and 0.29% Cu could be characterized as a fayalit e slag with a sulphide bearing glass matrix. While the fayalite contains most of the Co, Ni is enriched within both sulphides and fayalite. Cu is only present in higher amounts in sulphides or metallic droplets. This, as well as the small grain sizes of the mineral phases, inhibits significant enrichment by mechanical methods. However preconcentration is possible by means of magnetic separation. An effective hydro metallurgical approach proved to be oxygen pressure leaching with sulphuric acid. Accordingly, the method proposed for processing the investigated slags is to combine the normal utilization as coarse construction material with pressure leaching of the fines and the ground upgraded magnetic fraction. Besides the recovery of base metals, the leaching process yields fine-grained residues, which, after addition of CaD, will set to a cement-like material, or can be used as a pozzolanic cement colour. INTRODUCTIONDuring the pyro metallurgical processing of nickel ores, the valuable metals nickel, cobalt and copper are enriched within the sulphide matte, similar to the smelting of copper ores. The resulting waste materials are slags, which may still contain valuable metal contents of up to 0.5% or above . These contents are close to the cut-off grades of some nickel-cop per-cobalt deposits. The methods that are used to recover copper from slags comprise in general further pyro metallurgical treatment, often after enrichment by flotation. Another area of application for such slags is their use as construction material. However, this might cause environmental problems if nickel containing dusts are produced.Based on one example, the characerization and a possible way of complete utilization of nickel smelter slag s as construction materials in combination with partial base metal recovery are described in this paper. The investigated slag sample was obtained from a dump site in the Sudbury district, Ontario. Detailed test series for process optimization were not possible during this study due to the limited available sample size."

Jan 1, 1989

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However, high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives. IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million. Canada is second in world production of asbestos behind the U.S.S.R. The milling of asbestos ore has been done primarily by a series of steps involving crushing, dry-grinding and aspiration using large quantities of air to release the fibres. Contrast this process to those practiced in the purification of virtually every other mineral. Ores other than asbestos are crushed and milled using an aqueous slurry in rod, ball or pebble mills. The finely ground mineral, still as a slurry, undergoes beneficiation by froth flotation, heavy media separation, hydrocyclones or any of the other aqueous techniques currently employed in mineral processing.One of the driving forces behind the use of air instead of water as a means of separating asbestos is the nature of the aqueous asbestos slurry. While most slurries of minerals contain as much as 80070 solids and can still be pumped and transported, asbestos slurries become highly viscous with as little as 10070 solids. These high viscosities reduce the pumpability of the slurry and create severe handling problems. Mills become prohibitively large and uneconomical due to having to handle slurries containing only 10% rock and 90% water.Health-related issues have affected the use of asbestos in many countries. In Canada, the asbestos-producing provinces have introduced stricter occupational legislation to improve safety in the workplace. This primarily means strict control minimizing release of air-borne asbestos fibres . Quebec and Ontario have set limitations of airborne asbestos at 2 (2) and 1(3) fibre per cubic centimetre of air. With present milling technology, maintaining these low levels in the workplace requires constant vigilance."

Jan 1, 1988

By D. E. Barnett

"Paramount to sound aggregate resource management is an awareness of what resources exist. For the past six years, New Brunswick has been conducting granular aggregate resource inventories in and around urban centres as a means of documenting, both qualitatively and quantitatively, these resources.These aggregate studies require extensive ground truthing due to the often small nature of the surficial feature s as well as extensive foliage. Approximately 35% of the province&apos;s land mass has been mapped at a 1:50,000 scale as part of this on-going program. Reports are published annually and include data on size analysis, lithology soundness, abrasion and absorption.Aggregate deposits in New Brunswick frequently reflect the local bedrock lithology and, whereas much of New Brunswick is underlain by soft, friable sandstone of Pennsylvanian age, it is necessary to transport aggregate for higher-specification use considerable distances. Alternatively, the construction industry must turn to crushed stone as a source of asphaltic or concrete aggregate.Over 40% of New Brunswick&apos;s land mass is owned by the Crown, and aggregate resources are managed under the Quarriable Substances Act. Under this legislation, permit applications are reviewed by a Land Management Advisory Committee which consists of representatives from the various government departments involved.IntroductionSurficial materials either directly or indirectly form the basis of much of our economic activity, whether it is the field of agriculture, forestry, manufacturing, construction or other. Although sand and gravel have been produced and used since the day s of early settlement, the economic significance attached to such materials has only recently been recognized by both government and the general public."

Jan 1, 1982

? Élaboration de la Directive 019 (1982) ? Objectifs: ? Protection de l ?environnement ? Procédure administrative pour analyse et évaluation environnementale ? Officialisée en 1989 ? pas eu de modifications depuis ce temps Contenu de la Directive 019 ? Requête d ?autorisation ? Gestion des eaux ? Traitement des effluents ? Gestion des déchets et des résidus miniers ? Suivi environnemental Directive 019 Exigences environnementales ? Effluents miniers ? As, Cu, Ni, Pb, Zn, Fe, CN, MES, pH, toxicité aiguë ? Suivi environnemental annuel ? Effluent ? Réseau hydrographique ? Restauration

May 1, 2001