Search Documents

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By J. A. Jr. Carpenter

Expanding world economic prosperity, probable peaking of conventional petroleum production in the coming decades and environmental concerns require efforts to increase the efficiency of, and the development of alternatives to, petroleum-based fuels used in automotive transportation. In January 2002, the U.S. Department of Energy (USDOE) and the U.S. Council for Automotive Research (USCAR) of the "Big Three" traditionally-USA-based automakers, DaimlerChrysler, Ford and General Motors, formed the Freedom Cooperative Automotive Research (FreedomCAR) Partnership to fund high-risk, high-payoff research into advanced automotive technologies with the potential for eventually lowering the USA's nearly complete (95%) dependence on petroleum, 55% imported, for its transportation fuels. FreedomCAR replaced the Partnership for a New Generation of Vehicles (PNGV) which existed from 1993 to 2001. In January 2003, the energy-supply industry joined with the FreedomCAR Partnership forming the FreedomCAR and Fuel Initiative (FC&FI) to develop the technologies needed for the mass production of fuel-cell vehicles using hydrogen as fuel and the infrastructure needed to deliver the hydrogen to the consumer. The goal is to enable the automotive and energy-supply industries to make commercialization decisions in 2015 on large-scale introduction of such vehicles and on developing the infrastructure beginning in 2020. In addition to work on fuel cells and hydrogen infrastructure, the FC&FI conducts research on technologies with the potential for nearer-term energy efficiency and environmental benefits, such as new engine concepts, lightweight materials, and engine-electric hybrid propulsion systems. Lightweighting is seen as crucial for shorter and for longer term benefits because hybrid and fuel-cell powertrains are expected, at least in the early stages of adoption, to be heavier and more costly per unit of power than the standard internal-combustion, gasoline- or diesel-fueled powertrains they replace. Research and development (R&D) on casting of aluminum automotive components were major parts of the PNGV and R&D on casting of magnesium automotive components have been and are so under FreedomCAR. This presentation will review those efforts.

Jan 1, 2006

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By ByongPil Lee, Changkyu Lee, Jin Gyun Park, Hyung Sub Eom, Sung-Koo Jo, Jae-Young Lee, Gilsoo Han

"A new hydrometallurgical process for nickel extraction from a low grade laterite ore such as limonite has been developed by RIST and POSCO. This POSCO Nickel Extraction Process (PosNEP) consists of five main processes: ore reduction using hydrogen as a reductant; acid leaching at atmospheric pressure and temperature; cementation by the use of reduced-ore seed; production of the main product such as ferronickel or a high purity nickel compound; and production of by-products such as cobalt and iron in the forms of cobalt sulfate and iron oxide. In addition, hydrogen produced in acid leaching and hydrochloric acid regenerated in pyrohydrolysis for iron oxide production can be reused in the process, which makes PosNEP more cost-effective. The performance of PosNEP has been proven through pilot tests, showing that this process is economically and technically viable. In this paper, basic concepts and detailed test results of PosNEP are shown.INTRODUCTIONNickel has been extracted from two types of ore, sulfide and oxide ore. Nickel and cobalt usually occur together in the ores. The principal ore mineral of the sulfide is pentlandite, (Ni,Fe)9S8, which is easily beneficiated to produce sulfide concentrates(Moats & Davenport, 2014). These concentrates are usually treated by smelting and converting to make a matte. The produced matte is then purified through either hydrometallurgical or pyrometallurgical processes to produce high-purity nickel. In general, this process for sulfide ore has been known as a more cost-effective process than that for oxide ore.The oxide ore is laterite comprised of two different ore types, saprolite and limonite. The main nickel-bearing mineral of saprolite is nickeliferrous garnierite,(Mg,Ni)6Si4O10(OH)8, and that of limonite is nickeliferrous goethite (Fe,Ni)O·OH ore (Moats & Davenport, 2014). Since the saprolite has high contents of nickel and slag formers (MgO and SiO2) and a low content of iron, it tends to be treated by a pyrometallurgical smelting process such as calcination and electric furnace techniques to produce ferronickel for use in stainless steel. In this process, the cobalt in the ferronickel does not have any economic value."

Jan 1, 2017

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By W. C. Whittaker

Introduction When one thinks of a coal stripping deposit, the picture that usually comes to mind is that of a more or less flat seam from two to twenty feet in thickness overlain by ten to fifty feet of overburden, in suitable ratio for economic operation. This is the usual type of stripping deposit and is quite a common occurrence in various parts of the prairie provinces. Rather unusual types of coal stripping deposits are being presently worked as open-cut mines by Sterling Collieries, Limited, and the Co al Valley Mining Company, Limited, at Miles 47 and 48 on the Alberta Coal Branch, some 150 miles south west of Edmonton. These deposits are of interest chiefly because they represent turned-up and greatly thickened sections of the Mynheer seam, and as such they present their own problems, peculiar to the commercial exploitation of a seam of this type. The area in which these deposits occur was originally owned by the Pacific Pass Collieries, whose operations, however, were confined to under-ground mining at Lovett, some eight miles to the southeast. It was not until l918 that the value of these deposits was realized, when the Company now known as Sterling Collieries, Limited, opened their pit at Mile 47. At the inception of the work, coal was loaded directly into the railway cars by men using wheelbarrows. In 1920, a tipple was built, after which the coal was loaded by steam shovel into mine cars, hauled by steam dinkeys, and loaded over the tipple into railway cars. In 1922, the Coal Valley Mining Company entered the field at Mile 48, with an entirely mechanical equipment, and at the present rime these two are the only stripping properties in Alberta using mechanical equipment both for the removal of overburden and the loading of the coal. These Companies have operated continuously since that time, and have to date mined and shipped 4,000,000 tons of coal, and moved some 5,255,000 cubic yards of stripping. The present annual coal output for the two mines is about 240,000 tons.

Jan 1, 1935

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By A. Dave Mackintosh

Historical closure data has provided a description of the stress distribution patterns occurring around mine openings and enabled the development of a time ? distance plot predicting the location of the stress peak and its migration away from mine openings with time. Data collected from active mining areas during the 1970?s and 1980?s indicated the peak appeared to stabilize approximately 135m (450 ft.) from openings after four years. The region of high load and accompanying poor ground conditions in which the peak was centred was spread over approximately 45m (150 ft.) to 60m (200 ft.). Recent data from new development headings cut adjacent to 25 year old extraction areas suggests load transfer takes place over a much greater distance and time frame than predicted.

May 1, 2001

By R. Prioul, J. Kear, D. Chuprakov, A. P. Bunger

"Hydraulic fracture (HF) growth through naturally fractured rocks challenges the development of accurate predictive HF models. The authors present laboratory experiments differentiating behaviours associated with orthogonal and oblique intersections between HFs and natural fractures (NFs). HFs were created in sandstone and crystalline (gabbro) rock specimens, impinging orthogonally or obliquely on an unbonded machined frictional interface. Ultrasound monitoring was used to observe the rate of propagation through the interface. A contrast was observed between direct and offset crossing for orthogonal and oblique intersection, respectively. The stresses required to promote crossing depended on the intersection angle between HFs and NFs.RÉSUMÉ La propagation des fractures hydrauliques (FH) dans les roches naturellement fracturées pose un défi pour le développement de modèles prédictifs. Nous présentons des essais en laboratoire qui différencient les comportements associés aux intersections orthogonales et obliques entre les FH et les fractures naturelles. Des FH ont été créées dans des spécimens de grès et de roches cristallines (gabbro), heurtés de manière orthogonale ou oblique sur une interface machinée, non liée, de frottement. Un suivi par ultrasons a servi à observer le taux de propagation à travers l’interface. Un contraste a été observé entre un croisement direct et un croisement indirect des intersections respectivement orthogonales et obliques. Les contraintes requises pour promouvoir le croisement variaient selon l’angle d’intersection entre les FH et les fractures naturelles."

Jan 1, 2016

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine's well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019