Search Documents

By S. McPhail, D. Richardson, G. J. Simandl, C. Akam, S. Paradis, M. Yakimoski, A. Teucher, Y. Cui, F. Ferri

Historically, extracting dissolved solids from formation water was economically motivated. Today, main drivers are environmental benefits and regulations, as large volumes of water needed for hydraulic fracturing require treatment before reuse or disposal. The concentration of dissolved solids in flowback water increases with each use and may require treatment prior to disposal. Element recovery from produced water is not profitable unless market conditions are favourable, recoverable elements are abundant, and economical recovery methods are established. Sale of recovered materials could offset recycling and disposal costs. This paper describes markets for Cl, Na, Ca, K, Sr, Mg, Br, Ba, I, B, and Li, and their concentrations in produced water from oil and gas wells in British Columbia. It recommends revising sampling protocol for produced water.

Jan 1, 2018

By Bing Li, Kai Liu, Yongcheng. Zhao

With the ongoing development of copper smelting technology, the improvement of environmental emission control and achieving an automated continuous copper pyrometallurgical process have become the key development goals for copper smelting. The double bottom blowing continuous copper smelting process combine bottom blowing smelting (SKS) and bottom blowing converting (BCC) process and fire refining as “three-connected furnaces” arrangement is a pyrometallurgical process independently developed by China’s ENFI which can continuously produce copper from raw material through to anodes. This technology can improve energy efficiency and reduce environmental emissions for the overall copper smelting and converting process. This paper discusses the engineering characteristics and production practice of the SDIC Jincheng Metallurgical Project, which operates SKS smelting and BCC converting process with “three-connected furnace” arrangement for the first time in the world. Advanced engineering concepts and tools were used to optimize the configuration during the project engineering stage. The operation shows that the process has good environmental performance, reduced energy consumption and high level of automation, which is a new choice for copper continuous smelting process. INTRODUCTION One of the most important developing trends for the overall copper smelting process is to develop a continuous operation. Continuous copper smelting can maximise energy efficiency in copper concentrate and make full use of the rich heat treatment system. Cold charge and a part of low-heat-generating materials, which are processing with additional equipment in traditional copper smelting process, can be processed with rich reaction heat in continuous copper smelting and converting process to achieve good economic benefits. Yuan and Wang (2017) noted that SKS+BCC copper smelting process can reduce the secondary SO2 emissions compared with discontinuous copper smelting process, which required transportation of melted matte by matte ladle and may cause secondary pollution. The continuous copper smelting process can also reduce the generation of intermediate cold materials.

Jan 1, 2019

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By George W. Bain

Mr. Geo. W. Bain: Dr. H. C. Cooke's discussion of 'The Geology and Mineral Deposits of the Harricanaw and Bell River Basins' possesses many of the elements of a good political address; perhaps his long residence in Ottawa has some bearing upon his method of discussing geological work. The three essential parts of the address are all included. First, the plank - "Contributed discussion on the Geology and Mineral Deposits of the Harricanaw and Bell River Basins"; second, the personal attack upon the opponent, to show antipathy to the opponent as well as to his ideas; and third, controversion of a number of statements, which have been made to appear as planks of the opponents platform, even statements and work which are in no way connected with one under discussion. In the following pages, I will confine my attention to a defense of my work in the Harricanaw and Bell River basins, leaving discussion of the other areas mentioned by Dr. Cooke until results of the re-surveys are published. It is intimated that it was impossible to make a geological examination of an area of 1,600 sq. miles on a scale of four miles to the inch (base map supplied) in three and a half months, because "the area is accessible only from the railway along the northern edge together with a few roads close to it, and from rather wide separated streams?. There is one way, known to most geologists, whereby a place can be reached other than by railway coach or motor boat, and that the oldest of all -- walking. Most of the region was reached in this fashion. The boundaries of all the 18 townships included in the map are surveyed, nine are divided into lots, and the north-south and east-west centre lines of most of the others are surveyed and have mile-posts placed.

Jan 1, 1927

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966

By R. B. Allen, B. S. W. Buffam

"The property of Chesterville Mines, Limited, is in McGarry township, Timiskaming district, Ontario, about 25 miles east of Kirkland Lake. It consists of a group of fifteen claims that extend northeast from the KerrAddison mine for a distance of 2 miles.In June, 1906, two groups of prospectors left the town of Chesterville, Ontario, to prospect in northern Ontario. Silver had been discovered 3 years before at Cobalt and the large profits of this young mining camp were the principal incentive to extending the field of exploration northward. One group consisted of Dr. Reddick, Edward Flynn, John Hummel, William Knott, and Colin Cameron. The other group comprised J. T. Kearns, Herman Hummel, W. G. Barkley, and J. Elliott.The two groups travelled north by train to Haileybury and thence to Larder lake by canoe. Camps were pitched on the northeast arm of the lake, and within a short time a discovery was made by Edward Flynn of the first party, who found gold on the property now owned by Kerr-Addison Gold Mines, Limited. Herman Hummel and J. T. Kearns shortly afterwards made the second discovery, on what is now the Chesterville property. These discoveries, made some years prior to those at Porcupine and Kirkland Lake, are believed to be the first in that part of northern Ontario.The Hummel-Kearns claims were incorporated in the following year under the name of Chesterville Larder Lake Gold Mining Company, Limited. It was not, however, until 30 years later, in 1936, following the increased premium on gold, that sufficient capital was placed in the treasury of the Company to carry out an extensive diamond drilling programme. This exploratory drilling was started early in 1937 under the direction of Leo. J. Kearns, and a large body of ore was intersected in the first drill hole. Underground work was started in 1938, a mill was built, and the first gold brick was poured on July 29th, 1939."

Jan 1, 1954

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By S. A. G. Poppen, J. Konopka

"Petro-Canada&apos;s project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By S. A. Jacob

Magnesium sheet is notoriously difficult to form at low temperatures without initiating failure, In the present work cold rolling and annealing conditions are varied to produce samples of AZ3lB sheet with a range of grain sizes. The formability of these samples is investigated using tensile testing and forming limit diagrams (FLD&apos;s), The results are discussed in terms of twin types and frequencies.

Jan 1, 2005

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013

By Ltd Changsha Research Institute of Mining and Metallurgy Co., Shi Yunliang, Luo Yunbo, Chen Jun, Liu Miaohua, Xiao Jinxiong, Long Yan

"A refractory lead-zinc oxide ore located in Yunnan has hundreds of tons of metal reserves, which is hard to be recovered effectively by conventional oxide ore beneficiation methods. In this study, by sulfidation roasting of raw-ore, sulfide deposit is formed on the surface of the lead-zinc oxide ore, and then the roasted ore is processed with bulk flotation. The test results indicate that a bulk concentrate with grade of 7.85% lead and 34.24% zinc, recovery of 79.13% lead and 79.04% zinc, respectively, can be obtained by using conventional sulfide ore flotation method.The sulfidation process shows that pyrite in the raw ore releases S firstly, then S reacts with PbO and ZnO to transform into PbS and ZnS. When the mole ratio of sulphur:zinc is 0.59, the surface of smithsonite is covered with a layer of zinc sulfide. When the mole ratio of sulfu:zinc rate is 1.47, entire simthsonite particle is transformed into zinc sulphide. Thus the transformed particles can be recovered by flotation without complete sulfidation.INTRODUCTIONWith the increasing demand for zinc and decreasing of zinc resources, people pay more attention on development and utilization of zinc oxide ore. However, zinc oxide ore has wide range mineral kinds, complex mineral composition, disseminated fine-grained particle size, and high content soluble salt, so current study results about the zinc oxide ore with conventional flotation are not satisfactory. So far, process dealing with zinc oxide ore includes: sulfuration (Na2S)-flotation, direct flotation with fatty acids collectors, metallurgical methods, in which sulfuration flotation is the most widely used method. The basic principle of sulfuration flotation method is firstly roasting oxide ore with vulcanizing agent, and then recovering the sulfurated oxide ore with flotation, which is similar with recovering nature sulfide ore by using conventional collectors such as amines and xanthate."

Jan 1, 2016

By J. C. Gibson, C. H. Stockwell

"The San Antonio gold mine is at Bissett, Manitoba, on the north shore of Rice lake, 100 miles northeast of Winnipeg. Gold was discovered on the property in 1911, but intensive exploration was not undertaken until 1926. Milling commenced on May 1st, 1932. Total amount of ore milled from that time until the end of 1946 was 1,766,670 tons, having a value of $18,378,317.GENERAL GEOLOGYThe rocks in the vicinity of the mine are Precambrian and include three groups, namely, the Rice Lake series of volcanic and sedimentary rocks, basic and acidic intrusions, and a younger formation of sediments known as the San Antonio formation (Fig. 1). The lower part of the Rice Lake series, consisting of flows of rhyolite, trachyte, and andesite with interstratified beds of agglomerate, occupies an area extending southward from Rice lake. The lake itself and the country to both east and west of its northern end is underlain by the next succeeding beds of the series, which are chiefly tuffs, arkose, and conglomerate, but include a thin band of basalt. Northward from the lake, these are succeeded by the upper beds of the series, first a thin band of basalt and, overlying this, porphyritic andesite flows interlayered with beds of volcanic breccia or agglomerate.The Rice Lake series has been invaded on the east side of the lake by a body of basic rock ranging in composition from gabbro to diorite and quartz diorite, now much altered. This is cut by younger sills and dykes of basic rock, probably diabase, the original texture of which is largely destroyed by alteration. Numerous dykes of feldspar porphyry, quartzfeldspar porphyry, and a few of a rhyolite-like rock, occur south of the lake, but are uncommon to the north. They cut the diabase and older rocks.Extending westward from Rice lake and lying with marked angular unconformity against all of these rocks is the San Antonio formation, consisting of cross-bedded, arkosic quartzite."

Jan 1, 1954

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By Donald S. Cameron

By dispersing gold in high surface area form supported on metal oxides, its inert character can be transformed to make economical, effective catalysts. Gold has already been demonstrated in a number of fuel cell applications such as gas phase catalysts, electro-catalysts, and electrical connectors. In this paper, the various types of fuel cell systems are reviewed, and several opportunities for gold identified. Low temperature fuel cells, including alkaline and solid polymer electrolyte types rely on high surface area platinum group metal catalysts which are highly susceptible to poisoning by low concentrations of carbon monoxide in the fuel supply. Hydrogen is frequently obtained by steam reforming hydrocarbons, followed by the water gas shift (WGS) reaction. A promising initial use for supported gold catalysts is in catalysing this WGS reaction. Research has shown that gold supported on iron oxide (Au/a-Fe2O3 ) WGS catalysts are more active than the current commercial copper oxide / zinc oxide catalysts, and effective at temperatures as low as 120oC. Products from reformer/ water gas shift reactors can be further purified by removing traces of carbon monoxide. If a small proportion of oxygen is introduced into the fuel gas stream, carbon monoxide can be preferentially oxidized to carbon dioxide even in the presence of hydrogen. Gold nanoparticle catalysts on iron oxide support (Au/a-Fe2O3 ) have exhibited higher activity than commercially available platinum on alumina (Pt/?- Al2O3 ) preferential oxidation catalysts. The low temperature of this reaction may make it feasible to incorporate these catalysts within the fuel cell itself. Proton exchange fuel cells provide several possible applications for catalytically active gold and its alloys. Carbon supported platinum group metals would benefit greatly from improved electrical conductivity if gold replaced some or all of the carbon support material. As electrode current densities are raised, electrical resistance constitutes an increasing proportion of voltage losses within the fuel cell. Dramatic reductions in cell stack voltage losses have already been demonstrated by reducing inter-cell contact resistance using gold plating. The low temperature oxidation properties of gold catalysts have been investigated in controlling gaseous emissions from direct methanol fuel cells, and gold also provides essential catalysis in building direct borohydride oxidation fuel cells. The prospect of a range of other applications for gold in fuel cells to contribute useful improvements in corrosion resistance and conductivity is assessed. Globally, fuel cells have been developed for a wide range of applications including stationary generators, cars and buses, industrial vehicles and small portable power supplies, each of which represents a substantial market. Hence there are likely to be many and varied opportunities for gold catalysts to contribute to the performance and economics of the systems being commercialized.

Oct 1, 2003

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By D. M. Morrison

"The most important factor in Canadian mining is not the operating cost of current projects but the availability of capital for future projects. The future of mining at depth will be producing ore from the top of the orebody working downward with very effective, tightly controlled mining methods, i.e. either selective mining or bulk mining with well controlled dilution and fragmentation. The key characteristics of future mines will be smaller access excavations, more effective ground support, very precise blasting techniques and more efficient and reliable materials handling systems. Equipment will be smaller and designed for high efficiency and low maintenance, reducing both the capital and operating cost. This means there will be fewer scoops, more continuous mucking machines and conveyor belts, both lateral and vertical.Orepass failures have become accepted and the resultant redevelopment and retramming has become common. The capital investment in so-called permanent ore passes and crusher stations becomes questionable, particularly when crushers are only necessary for less than 10% of the ore going through the system. The best way to solve the chronic instability of ore passes is, as with all of the stability problems at depth, by reducing the excavation size rather than increasing ground support. Smaller access drifts would reduce the capital cost and increase the rate of development as well as reduce the amount of waste to be handled, reducing the ground support and the ventilation requirements. Large drifts and ore passes are essential only for the equipment needed to handle large pieces of ore and the productivity of scoops is very expensive when the requirements for ventilation and large access drifts are taken into account. The key issue is the fragmentation generated by primary blasting.The future of mining in Canada will depend on simple and robust technology geared to the environment in which it will have to operate. Its survival will depend on some-thing much more fundamental and difficult to accomplish than a technological advance — it will require a dramatic change in the way the mining process is managed, how work is organized, how effort is rewarded and how costs are measured — a complete change in mind-set."

Jan 1, 1996

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By N. T. Oo, L. D. Hutton

"The Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. A site specific rock classification system was developed that characterised all the rock units based on the engineering properties governing the rock mass behaviour i.e. intact rock strength and defect characteristics (spacing, aperture, infilling, wall roughness and weathering) irrespective of the geological origin. This approach simplified the design and the on-site verification processes. Based on this classification system, rigorous quantitative statistical assessments of the available geological information including various laboratory and field testing were performed to derive the geotechnical design parameters for various rock classes. These parameters were used to complete geotechnical designs of retaining wall systems. INTRODUCTIONThe Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The key features include two interchanges, a 300m long viaduct, a large cutting through Sexton Hill with an associated 100m wide Land Bridge and retaining walls reaching 490m long and up to 22m high. This paper focuses on the derivation of representative geotechnical parameters for geotechnical design of the retaining structures supporting Sexton Hill Cutting including bored pile retaining walls and soil nail walls. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. Due to the complex geological nature of the site, an understanding of the regional and local geology, the typical behaviour of individual geological units and the implication of onsite variations from design intention are the ultimate challenges to the geotechnical engineer in order to select representative geotechnical parameters for design."

Jan 1, 2015

By J. F. Fiset, N. Bouzoubaâ, N. Reynier, C. Laviolette, Canadian Nuclear Laboratories

Canadian Nuclear Laboratories (CNL) is developing a disposal strategy for radioactive wastes, which contain significant amounts of uranium, cesium, and mercury. There are safety and economic incentives for the extraction of these elements before permanent storage in deep underground repositories. In addition, the actinide elements are also an important component in rare earth element (REE) ores and considered as impurities. Actinides separation from REE tailings is a significant concern in order to manage radioactive nuclides. Reprocessing mine wastes may present significant financial and environmental benefits. Experiments were carried out with radioactive cemented wastes (RCW) prepared at CanmetMINING. For all of the tested RCW batches, solubilisation yields are above 97% for Cs and 98% for U and Hg. Sulphuric acid leaching with potassium iodide improved the solubilisation of Hg by oxidation and formation of the tetraiodide complex (e.g. HgI4 2-, Kf = 2.1030). Cs and Hg were removed selectively by using potassium cobalt hexacyanoferrate (KCFC) and Lewatit TP214 ion-exchange resin respectively. U recovery using the chelating resin Lewatit TP260 was the most efficient. The presence of high iodine concentration improved the U uptake by the resin. The best U elution was obtained using 1 M Na2CO3, which resulted in 99% U recovery. U was then precipitated as sodium diuranate. A counter current effluent recirculation was performed successfully on RCW. The process was also applied to submerged tailings collected from two U mines and an REE ore. This paper presents an innovative process, using sulphuric acid and potassium iodide, for U, Cs, a

Jan 1, 2016