Search Documents

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By Z. Y. Liu

A local additional potential model (LAPM) was developed to illustrate the role of strain rate in stress corrosion cracking (SCC) of pipelines. According to LAPM, both density and mobility of the local active spots on the steel surface, i.e., dislocation emergence points, increase linearly with strain rate. Generation of such active spots introduces an additional negative potential locally, affecting the electrochemical reaction and, consequently, the susceptibility of the steel to SCC. Electrochemical corrosion measurements, slow strain rate tests and electrochemical hydrogen permeation test were combined to demonstrate the validity of LAPM to illustrate pipeline SCC in an acidic soil solution. It is found that a maximum of the SCC susceptibility occurs at strain rate of 10-6 s1, which is associated with an enhanced hydrogen evolution due to the local additional potential (LAP) effect.

Jan 1, 2010

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls’ life and facilitating rolls’ change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By Y. Serres

In the past, conventional reflection seismic techniques were not very successful when applied to typical mining exploration: they lacked resolution in the shallow range or were not cost effective. By combining a light earth tamper source, special geophones and field procedures, a stacking process of the returning seismic events using a microprocessor system, and a sophisticated sequence of adapted digital data processing, Mini-Sosie achieves high resolution in the 100-ft to 4000-ft range. Additional advantages result from the very quiet nature of the source and flexibility of the system. Although Mini-Sosie might be used in the refraction mode, or for well velocity logging, it has found its main applications with the reflection technique.

Jan 1, 1978

By Geology Staff, C. H. Stockwell

"The Flin Flon base metal mine, owned and operated by the Hudson Bay Mining and Smelting Company, is on the Manitoba-Saskatchewan interprovincial boundary at a point 400 miles north of the International boundary. The deposit was discovered in 1914 by Thomas Creighton and the Mosher and Dion brothers. Since production commenced in 1930, 25,000,000 tons of ore have been mined. On January 1st, 1946, reserves were estimated to be 26,000,000 tons, averaging 2.99 per cent copper, 4.i4 per cent zinc, and 0.089 oz. gold and 1.25 oz. silver per ton. In addition to the four metals named, others recovered from the ore include- cadmium, selenium, and tellurium. The mine workings extend to the 3,750-foot level, but little development work has yet been carried on below 3,250 feet.The known ore occurs in six lenticular to irregular bodies within a zone 500 feet wide. These bodies average 900 feet long, 70 feet wide, 1,500 feet in vertical depth, and 2,500 feet in length along the plunge. They were formed by replacement of the country rock and include ore of two types, solid sulphides and disseminated sulphides. Seventy per cent of the total known ore is of the solid sulphide type. This consists essentially of metallic sulphides- chiefly pyrite- with included remnants of the host rock, and additional quartz and carbonate. In places, the ore exhibits banding, inherited from pre-existing structures. The disseminated ore occurs usually on the footwall side, and along the bottom of the plunge, of the solid sulphide bodies."

Jan 1, 1954

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By A. M. Bell

"The property of Gaspe Copper Mines, Limited, is in the Gaspe Peninsula some 60 miles west of the town of Gaspe and 20 miles in from the north coast. The Copper Mountain deposit was first discovered in 1921 and first optioned and drilled by Noranda in 1938. The Upper Needle Mountain showings a mile south were found in 1938, but it was not until after a delay of 10 years that the more important deep ore at Needle Mountain was located by drilling. Production started in 1955, and the smelter commenced operation in December. Mining is by open stope methods with first production coming from the Lower Needle Mountain orebody, of which only a small portion has been exposed in underground openings.Stratigraphy and AlterationThe country rock is composed of limy siltstones of Devonian age. Away from alteration these are dark and generally carbonaceous. Throughout the drilled area numerous narrow layers of tuffaceous fragmental material occur, and such beds are found to provide excellent horizon markers by virtue of their uniform thickness and wide lateral distribution. These markers are valuable for stope control in mining the bedded replacement deposits.Intruding the sediments at Copper Mountain are porphyry dykes, and one drill hole encountered granite 1,400 feet below the valley. Solutions responsible for the rock alteration and ore deposits seem to have emanated from this intrusive centre.On the mine claims strong hydrothermal alteration has completely obscured the original character of the sediments. The unaltered formations are all very similar in appearance, but following alteration rocks that are very dissimilar in physical characteristics are produced, and such differences have an important influence on ore deposition. The alteration effects are known to extend over a vertical range in excess of 3,000 feet and have a surface area of two square miles. All known ore bodies are within the zone of alteration. In this, rocks are strikingly bleached to a white colour in contrast to the normal dark-coloured sediments, and are much harder and more abrasive, with bedding often obscured. The first effect of alteration is driving off of carbonaceous matter, followed progressively by silicification in the acid rocks and by the formation of lime silicates in the lime rocks, with an accompanying gain in silica and a corresponding loss in lime. Extensive analysis has shown that there is an actual addition of silica involved in the alteration."

Jan 1, 1949

"In the first half of 1990, Cambior earned $1104 million, or $0.37 per share, on revenues of$66.4 million. The company&apos;s strong cash position, attained late in 1989 and in the beginning of1990 through the exercise of warrants, put working capital at $83.8 million as of June 30, 1990. Long-term debt was reduced by over $10 million during the weak gold market, leaving the company with a debt to equity ratio of only 0.03. Production for the six first months of 1990 was 107 720 oz. Au, an increaseof24% over the corresponding period in 1989.Financial Profile/Results and Corporate Financial StrategiesTotal revenue for the 1989 fiscal year was $116,883,000 compared to $109,848,000 for 1988. The 1989 results achieved despite a lower average gold price, resulted from a higher level of commercial gold production and a 115% increase in investment income over 1988. Investment income rose to $3,568,000 in 1989 due to higher levels of cash assets.Cambior&apos;s mine operating costs increased 19% to $68,561,000 in 1989 from $57,472,000 in 1988. This increase resulted from rising operating costs at the Doyon Mine ($250/oz to $274/oz) due to the shift from open pit to underground operations, as well as from the start -up of three new mines with relatively higher costs. These costs have reached a stable level that should be maintained for the next few years.In 1989, net exploration expenses were $6,838,000, down 31070 from 1988, partially due to the Canadian tax reforms introduced since 1987. Depreciation and depletion grew by $1,432,000 in 1989, reflecting a higher volume of commercial production from the Pierre Beauchemin, Lucien C. Beliveau and Chimo mines.Net earnings for 1989 amounted to $17,661,000 or $0.73 per share compared to $17,438,000 or $0.74 per share in 1988.Cambior has an exceptionally liquid and strong balance sheet. As at December 31, 1989, net working capital stood at $85.6 million, with a total assets base of $338.6 million. With a long-term debt (including gold loans) of $21.5 million and shareholders&apos; equity of $277.2 million, Cambior has a debt to equity ratio of 8%. All but about $100,000 of long-term debt is in the form of gold loans.The total market value for Cambior&apos;s stock as at September 10, 1990, stands at $420million, based on recent stock market prices. Cambior&apos;s stock and warrants are traded on the Montreal and Toronto Stock Exchange."

Jan 1, 1990

By Frank Doxley

"FIRST OF ALL I should like to express to the members my sincere thanks for having had the privilege of serving them as President during the year now ending, to the Council for their guidance, and to the Secretary-Treasurer for his untiring efforts on both the Society's and my behalf during my year of office.During the .past five years the Canadian •Coal picture has changed considerably. In the West, production has been almost halved and many mines have been closed, due to the development and expansion of oil and natural gas industries, which, with some imported residual oil -on the Pacific coast -have provided competition which has been impossible to meet. The two major railway companies have embarked on an oil-burning and dieselization .programme and with this has .been lost one of the largest available markets for coal. Natural gas pipe-line installations still further threaten the remaining outlets for Western coal.In the East, retention of markets has also been a •problem, due to the intense competition provided by imported American •coal and the importation of residual oil.Because of cost it is impossible for central industrial Canada to be supplied with .coal from the Maritimes and markets are, therefore, restricted to fringe areas in Ontario and Quebec, and the Maritime Provinces.The dieselization programme of the Canadian National Rail ways has meant the loss of a large market for Nova Scotian coal and it is fair to assume that within a comparatively short time the market will be completely lost."

Jan 1, 1955

By Stanley Davidson

"This description of the structural geology of the Beattie mine has been condensed from a more comprehensive paper published previously (4).The property is in western Quebec, a short distance east of the Ontario boundary on the extension of the so-called Porcupine belt into Quebec.According to the geological surveys of the Dominion and Provincial Governments the regional structure in the vicinity of the mine is an easterly pitching, overturned syncline with several thousand feet of Timiskaming sediments in the centre surrounded by Keewatin volcanics (1, 2, 3).The mine lies on the north limb of the syncline, and the Keewatin series in this locality is, with few exceptions, overturned, dipping steeply north and facing south.The mineralization is closely related in space, and possibly genetically, to a body of syenite porphyry intruded into the Keewatin series along the north limb of the syncline. No ore has been found very far from the syenite or related lath-porphyry dykes, and the largest orebodies are composite, consisting of bleached and brecciated volcanics ( primarily tuffs) adjacent to altered syenite porphyry, both silicified and mineralized with very fine pyrite and arsenopyrite. In addition there are important ore shoots following a fracture zone within the syenite."

Jan 1, 1954

By H. T. Fargey

This paper considers the social, economic and political factors and their influence on future production and marketing of Western Canadian minerals. Among the subjects discussed are inflation, taxation, anti-combines legislation, unstable international currency relationships, economic nationalism and protectionism, the European Common Market and environmentalism.

Jan 1, 1973

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, &apos;longwall&apos; and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011