Search Documents

By M. Nusheh, C. Bumby, A-H. Puichaud

"Vanadium-bearing titanomagnetite ironsand deposits occur along a 480 km stretch of the west coast of New Zealand. In the present study, the leaching behaviour of NZ ironsand was investigated in hydrochloric acid (2–10 M) solution at 50–80°C for 2 h. The resulting leaching liquors exhibited Fe/V ratios in the range 150–180. The distribution of trace element contaminants between solution and solid residue was investigated, and processing conditions have been determined for rapid and efficient dissolution of Fe, Ti and V into the leaching solution. In addition, mineralogical analysis of raw ironsand and leached residues was performed in order to study the leaching mechanism. Samples were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), X-ray fluorescence spectroscopy, qualitative and quantitative X-ray diffraction and inductively coupled plasma mass spectrometry (ICP). Results indicate that the dominant dissolution process follows shrinking particle mechanism. However, ironsand particles containing ex-solution lamellae exhibited a different leaching behaviour compared to homogenous titanomagnetite particles.INTRODUCTION Titanomagnetite ironsand (blacksand) forms Quaternary onshore beach and dune deposits and offshore marine deposits (Figure 1) along 480 km of coastline from Kaipara Harbour south to Wanganui on the west coast of the North Island (Christie, 2016). It attracted the attention of scientists from the earliest times (Galbreath, 1998). The principal minerals in ironsand are titanomagnetite (TTM), ilmenite, quartz and ferromagnesian minerals such as augite, hornblende, diopside, and olivine with smaller amounts of rutile and apatite (Mauk, 2016).Several large ironsand deposits have been discovered and exploited since the late 1960’s. The Waikato North Head and Taharoa mines are currently operating and they have a 2015 measured resource of 400 million tonnes in total and provide over 2 million tonnes of concentrate per year by simple cost effective magnetic separation process (Christie, 2016; Christie & Brathwaite, 1997). The concentrate contains not only 7–8% TiO2 and 56–60% SFe, but also 0.3–0.6% V2O5, is both a valuable titanium mineral and a source of vanadium. All the production is used for steelmaking industries. The other potential for utilizing more of this resource without requirement of integration into an iron and steel producing plant is to develop a hydrometallurgical route with advantages of higher efficiency along with lower emissions. Currently, there is no existing commercial process capable of extracting all three of these elements as industrial-grade commodity products. Acid leaching of TTM concentrate with higher degrees of recovery and selectivity is a key step in any possible hydrometallurgical route."

Jan 1, 2017

By O. W. Ellis

Introduction During the month of September, 1928 enough money had. been promised by private individuals and corporations to comply with the Research ?Foundation Act 1928 (Chapter 57, 18 George V) of the Province of Ontario. The Ontario Research Foundation (referred to below as O.R.F.) may be said to 1iave come into being at that time. Under the terms of this Act, the Treasurer of the Province was empowered to match dollar for dollar of the sums subscribed by private .corporations and individuals up to a limit of $1,000,000. However, the response to the appeal for this by the Premier of the Province, the Honourable Mr. G. Howard Ferg uson, was so exceptional that the Act was amended in 1929 so as to empower the Treasurer to increase the maximum contribution on the part of the Province to $2,500,000. In March, 1933, the Chairman of the Foundation, Sir Joseph Flaville, Bart., was able to report that, in the interval between the Premier's appeal and December 1st, 1932, private enterprise had paid ?into the treasury of the Foundation $1,670,050, and that the Provincial Treasurer had assumed responsibility for a like sum. The endownment Fund of the Foundation was, therefore. $3,340,100. This sum was ?invested a lm~ s t entirely in Government securities, in securities guar. anteed by the Government, and in 1mmicipal securities. Sir Joseph Flavelle remarked at that time that "The payment of $1,670,050 to the Endowment of the Foundation by private persons and corporations is a somewhat remarkable performance when it is remembered that for three of the five years the business of the country has been suffering from a severe depression". Since that time it has been the consistent policy of O.R.F. to live within the income derived (1) from the investment of its Endowment Fund and (2) from fees collected for services rendered.

Jan 1, 1950

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By P. C. Richards

"Future Integrated Gasification Combined Cycle (IGCC) power plants will have superior environmental performance and unmatched efficiency.The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an IGCC plant. SCGP flexibility has been demonstrated for feeds ranging from bituminous coals to lignites and petroleum coke, and the process is ideally suited for combined cycle power generation, resulting in efficiencies of 42% to 46% (LHV).In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology is being built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N. V. Sep). The plant is scheduled to start up in 1993. IntroductionBasic ConceptShell's experience with gasification dates back to the 1950s, when the first Shell Gasification Process was commissioned with oil as feedstock. There are now over 140 SGP gasifiers licensed. The experience gained on oil gasification provided a firm theoretical and practical base for the start of coal gasification process development in 1972.At that time, there were serious concerns about the future availability and price of crude oil. Coal gasification (making carbon monoxide and hydrogen by the partial oxidation of coal) was considered to be an important option for refinery applications, because the synthesis gas (syngas) produced can be used as:• a chemical feedstock for making transportation fuels and chemicals;• a source of hydrogen (making use of the water gas shift reaction) for upgrading petroleum products; and• a fuel for heating process streams and/or generating electricity."

Jan 1, 1994

By Hugh S. Spence

This paper deals with an occurrence of radium ore near Wilberforce, Haliburton county, Ontario, upon which development work has recently been undertaken and which seems more likely to prove of commercial grade than any other deposit' of radioactive minerals hitherto found in Canada. This occurrence is sometimes called the Richardson property, after Mr. W. M. Richardson, the discoverer, and will be so referred to in the present paper. Occurrences of radioactive minerals are not uncommon in eastern Canada, and a number are recorded in the literature. The earliest of such references is probably that in Geology of Canada, 1863, where is mentioned an occurrence of uraninite at Mamainse, on the east shore of lake Superior. The mineral was first described by J. L. Leconte, in 1847, under the name of coracite, and was said to occur in a two-inch vein at the contact of trap and syenite. Search for this locality in recent years has proved unsuccessful. Obalski, in 1894, mentions (1) the occurrence of uraninite at a mica mine near Murray Bay, Que. In 1903, Obalski records (2) tests made on this uraninite by Rutherford and the Curies and the determination in it of the then newly-discovered element radium. In 1901, he mentions (3) the occurrence of uraninite at the Villeneuve mica mine, on the Lievre river, and of samarskite at the Maisonneuve mica mine, in Berthier county.

Jan 1, 1930

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By M. Remillard, M. Garon, M. Thérien, D. Hodouin

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami division of Noranda Inc. have been sampled for particle size distributions chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMAT. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper clean¬ing flotation stages and to determine how overall silver and three silver-bearing minerals are recovered in the plant final products.RESUME Dix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, analyses chimiques et le contenu d'argent et d'or des fractions granulométriques. Le bilan métallurgique a été obtenu à l'aide du programme BILMAT. Ces résultats couples avec une etude minéralogique à la microsonde sont utilises pour quantifier les pertes argentifères aux diverses étapes de nettoyage du circuit de cuivre et pour de¬terminer la repartition de l'argent et des trois minéraux argentifères dans les produitsfinals de l'usine.INTRODUCTION The Matagami division of NORANDA INC. produces copper and zinc concentrates from a sulphide ore which contains a small amount of gold (0.34 g/t) and silver (20 g/t). Only a small part of the silver (~-30%) is presently recovered in the copper concentrate. The objective of this study is to evaluate the metallurgical behaviour of silver, and secondarily of gold, in the flotation circuit for a possible increase of its recovery in the copper concentrate to improve its economic value. For that purpose it is worthwhile to study the minerals which bear silver and to determine the critical flotation stages where they are lost in the tails. The methodology proposed here is based on a coupling of a mineralogical study and a detailed mass balance calculation in the flotation circuit."

Jan 1, 1986

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC's confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By Walter Curlook

"With Inco recording record profits over the past year, most people have forgotten the painful years of the last recession/depression when Inco was losing up to a million dollars a day for a short period . While high nickel prices have contributed to the exceptional recent profits, the real achievements stem from the tremendous advances in productivity and cost improvements that make Inco one of the lowest cost nickel producers.Some of the major advances in productivity have occurred in the mines. The establishment of Mining Research Departments in both Thompson and Copper Cliff in 1979/80 provided the stimulus and the opportunity to dedicate personnel to specific research projects, on a full-time basis; and more particularly to concentrate on the efficiency of the total mine system. The Copper Cliff North Mine was brought back into production as a research mine dedicated to the development and testing of new mining methods and equipment. A shop facility known as the ""Murray Shop"" was set up as the centre of innovation for the development and construction of prototype equipment required for new bulk mining methods. While other expenditures were being curtailed , investment in mining research was being increased. An early success was an ""in the hole"" drill that could be broken down into small components to access even the remotest sectors of a mine to convert labour intensive undercut-and-fill mining to "" vertical crater retreat "" , VCR, bulk mining. A new mine manufacturing company-Continuous Mining Systems-was incorporated with the objective of building innovative mining equipment, with strong focus on automated continuous sytems. Continuous Mining Systems has now grown to a $25 million per year business. With these synergistic thrusts, the VCR bulk mining method was implemented in all of the Ontario Division mines, raising the percentage of ore mined by bulk mining techniques from 320/0 in 1981 to over 90% today. Coupled with re-designed job responsibilities, sup- ported by appropriate training, mine productivity more than doubled. It was discovered that VCR mining could be adapted to the narrower Thompson mine ores with identical improvements in productivity. Development of the Thompson Open Pit North had an additional favourable impact on production cost s in Thompson. The timing of the open pit development could not have been better. It permitted Inco to rapidly increase production at high productivity and low cost, in years of record demand and prices."

Jan 1, 1990

By Bruce Peberdy

Outline ?Building Systems ?Climatic Effects ?Thermal Effects ?Building Components ?Building Materials ?Structural Deterioration ?Maintenance Considerations

Nov 1, 2011

By E. Goris Cervantes

"A theoretical framework based on a detailed analysis of mine operations data from an oil sands mine in northern Alberta and the static simulation of truck cycle times are developed, verified, and validated in this paper. Implementation of this framework provides better results than existing tools that rely solely on manufacturer data. This, therefore, aids in efficient equipment planning for the life of the mine. The use of this framework to modify existing productivity curve estimation methods currently in use at the mine site is also proposed. This method replaces “loaded flat haul” with “loaded effective flat haul” in the productivity estimation. Validation of the model results in a 4% overestimation of productivity, versus an underestimation of more than 10% when using the existing in-house method. ¦ KEYWORDS Equipment planning, Life-of-mine (LOM) planning, Oil sands, Productivity, Truck cycle times RÉSUMÉ Un cadre théorique fondé sur une analyse détaillée des données relatives aux activités minières d’une exploitation de sables bitumineux dans le nord de l’Alberta et la simulation statique des temps de cycle des camions sont développés, vérifiés et validés dans cet article. La mise en oeuvre de ce cadre offre de meilleurs résultats que ce que proposent les outils existants, lesquels se basent uniquement sur des données des constructeurs. Ceci contribue donc à une planification efficace de l’équipement pour des projets relatifs à la durée de vie de la mine. On propose également de se servir de ce cadre pour modifier les méthodes d’estimation de la courbe de productivité actuellement utilisées sur le site minier. Cette méthode remplace le concept de loaded flat haul (la distance parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) par celui d’effective loaded flat haul (la distance relative parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) dans l’estimation de la production. La validation du modèle résulte en une surestimation de 4 % de la productivité, par rapport à une sous-estimation de plus de 10 % avec la méthode actuellement utilisée en interne. ¦ MOTS CLÉS planification de la durée de vie de la mine, planification de l’équipement, productivité, sables bitumineux, temps de cycle d’un camionINTRODUCTION One aspect that differentiates oil sands mines in northern Alberta from conventional hard-rock mining is the environment in which they operate. Due to ground characteristics, producers in the region experience roads with very high rolling resistance (RR) that, in turn, negatively affect haul-truck performance and greatly increase fuel consumption and emissions. Oil sands mining companies use some of the largest haul trucks in the world. In addition, oil sands mines cover more extensive areas than hard-rock pits, resulting in longer haul distances on roads made of comparatively more viscous material."

Jan 1, 2019

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the ClM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposits. Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. UranitnlHeiated studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to D were presented in previous issues of the ClM Bulletin, abstracts related to themes E and F are presented in this issue. The remaining abstracts will be presented in a future issue."

Jan 1, 1994

By J. W. Matousek

Tonnage oxygen plays a critical role in the primary production of two of the most important industrial metals - copper and iron - and minute quantities of oxygen play equally critical roles in determining the properties of the market products. For refined copper, oxygen in the final metal is balanced between maximizing electrical conductivity, neutralizing the effects of harmful impurities, and ensuring that the metal takes on the desired "set" during casting - the surface texture and physical properties required for subsequent rolling and drawing. For refined iron, oxygen must be removed to minimize reaction with carbon during cooling from the molten state with the generation of CO and CO2 - leading to a loss of carbon and the creation of "blow-holes" in the solid ingots and the potential for defects in rolled and forged products. This paper reviews the thermodynamics of oxygen in molten copper and iron at the levels of primary interest to production metallurgists.

Jan 1, 2014

By Glen Robertson, Jeff McLaughlin

"The Clarabelle Mill rock tailings have the potential to generate sulphuric acid through chemical and biological oxidation of sulphide minerals. Current rock tailings assay between 0.80 -1.40 %S, with sulphur occurring principally as coarse pyrrhotite. Acid generation within the tailings area can be substantially reduced by segregating pyrrhotite rich tailings in a submerged storage area and by depositing only low sulphur rock tailings in exposed areas. Laboratory tests confirmed that low sulphur tailings could be produced by flotation at reduced pH with a small xanthate addition. A plant test was conducted to evaluate the production of low sulphur tailings in conjunction with INCO's continuing commitment to environmental protection and progressive decommissioning of the metallurgical site.During the plant evaluation, approximately 5% of the mill rock tailings were reprocessed in a line of 100 tt3 Denver flotation cells. Tailing grades below 0.40% S were easily achieved through operation at pH 6 -7, with xanthate addition (dosages up to 0.02 lb/ton) and 10 -15 minutes of nominal retention time. Froth depths between 1 -3 inches combined with relatively liberal amounts of frother were required to pull the lightly mineralized froth into the concentrate which averaged 11% sulphur and less than 5% mass recovery. In addition, three field lysimeters were each filled with two hundred.ton bulk samples of low sulphur tails (0.35% S), standard rock tailings (0.98% S), and mill total tailings (2.30% S) for long term monitoring. The implications for full scale plant design, tailings area decommissioning, the possibility of increased nickel recovery and preliminary field lysimeter data are discussed."

Jan 1, 1994