Search Documents

There has been considerable attention in the literature to coarse sizing by wet and dry screening, but these methods have not proven to be applicable to the calculation of screen capacities for fine wet sizing, desliming and media recovery: A method is presented for the calculation of the size of screens for such duties, being based on the mean particle size of the oversize material on the screen which reflects the surface area from which the fines or media must be removed. Similarly for dewatering, it is the area from which the water must be drained. Desliming, media recovery and dewatering are each considered along with water require- ments both with the feed and as wash water.

Jan 1, 1984

By E P. O’Dwyer

Segment and gasket lining in tunnel boring machine (TBM) tunnels; and sheet membrane lining systems in driven tunnels are robust waterproofing systems each with a proven history of performance in Australia and further afield. Where an interface between these two systems occurs, the potential for costly failures is vastly increased and additional attention to detail is required in design, planning and construction. TBM cross-passages represent the most common occurrence of this interface, with steel compression flanges and neoprene gaskets being the typical means of connecting the waterproofing systems. There is a large variance in both detailing these flanges and associated outcomes, which makes this an area where there is room for improvement within the industry.The paper will look to tease out the various issues associated with this interface and how they can be dealt with efficiently with appropriate design measures, robust planning and carefully controlled construction methods.The paper will also look to review the new technologies and systems currently being put forward as potential alternatives, including an epoxy tape system, which has recently been successfully trialled on a project in Europe under high-pressure head.CITATION:O’Dwyer, E P, 2014. The challenge of waterproofing cross passages in segmentally lined tunnel boring machine tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Kleinitz, J Halilovic, K Trappitt

Mine operators use grade control to determine the destination of each block of material in the mine. In polymetallic mines, grades are best expressed in dollars: the Net Smelter Return, NSR, per tonne. To estimate NSRs, geologists working on grade control develop models for each geometallurgical domain in the mine. These models may incorporate observations on the mineralogy and grain sizes of the material being examined. The site’s mill operators contribute to the models by providing geologists with statistical analyses that relate assay results and mineralogical compositions to metallurgical parameters, such as the rates of recovery of each economic metal to each of the concentrates produced, and the compositions of those concentrates. The team responsible for sales and marketing of the site’s products contributes to the NSR models by providing details of the costs of shipping concentrates to smelters and refineries; and by providing figures that are specified in the smelter contracts, such as the payability of the metals in each concentrate and the fees charged by the smelter. The mill operators also provide, for the NSR models, equations to estimate the rates of recovery of deleterious materials to each concentrate. Deleterious materials comprise mostly halogens and amphoteric elements, both of which reduce the efficiency of smelters. Furthermore, deleterious materials such as antimony and arsenic may be poisonous to people and to the environment. The sales and marketing team provide specifics of the penalties that smelters impose upon deleterious materials. These penalties may reduce NSRs by tens of percent, possibly to levels below the cut-off grade. Thus, in the blocks that are subject to grade control, mine geologists monitor not only the concentrations of economic metals, but also the presence and abundance of deleterious materials. The preparation and maintenance of models, to estimate NSRs and to assess changes in the levels of potentially toxic materials to be mined, requires close and continuing consultation between corporate departments. There must be strong communication of mine geologists with the mill operators; with the people who market the mine’s concentrates; and, should there be a risk of encountering toxic levels of deleterious materials, with the mine’s health, safety and environmental officers. This co-operation could require radical changes in the structure of many organisations. However, experience suggests that such changes can significantly improve the profitability of a mine.

Mar 22, 2022

There are a number of different mechanisms by which wetlands can immobilise the metals in mine drainage. Here, the biogeochemistry behind four of these mechanisms (adsorption, biological uptake, precipitation as oxyhydroxides, and precipitation as sulfides) is discussed from the perspective of sustainability. Moreover, treatment wetlands are considered as part of a larger system, also taking into account the source of the drainage and various aspects of the receiving waters. The biogeochemistry of different metal immobilisation mechanisms in wetlands determines what kind of drainage can be treated with success, and it also places an upper limit on the amount of metal that can be removed from the water phase per unit of time. This has important implications for the design of treatment wetlands, perhaps particularly in colder climates. A thorough understanding of the prevailing biogeochemical processes is essential when attempting to establish treatment wetlands after the closing of a mine. If a wetland is to be used as a sustainable æwalk-awayÆ solution, the anticipated change in treatment efficiency over time (as pollutants accumulate in the system) must be considered in relation to the expected changes in drainage quality. It is also important that the total metal immobilisation capacity of the wetland is not exceeded and that the integrity of the system is maintained, in order to minimise liberation of previously immobilised metals.

Jan 1, 2003

By S Servant, T J. Bidwell

Paste backfill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste backfill is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the backfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in situ measurement of paste backfill properties.

Jan 1, 1998

By T Stambolie

Mine planning processes are continuously evolving, increasing in complexity, and are required to be developed in shorter timeframes, often missing important steps in the process. Underground coal mines are also moving into more challenging environments, with the more favourable resources having been exhausted. In addition to traditional mine planning processes there is an increasing level of complexities associated with parallel systems including the preparation of Joint Ore Reserves Committee (JORC) compliant estimates (JORC, 2012 and Guidelines Review Committee, 2014) or seeking critical regulatory development consent to undertake mining. There is a clear link between geotechnical considerations and success of mining operations, and therefore it is essential that such considerations are elevated in both status and priority. It is obvious that geotechnical considerations are paramount in any mine, however it is imperative to accept that such considerations, and the collection of information relating to such, are undertaken from the onset of any mining project. CITATION:Stambolie, T, 2018. Elevating geotechnical considerations in the Australian underground coal industry and mine planning process, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 383–391 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The evolution of mineral sand mine rehab ilitation techniques have been techniqually based. Research and investigations have been carried out by government authorities, mining companies and academic institutions. Protection of the physical and biological environments is a vital part of any mine oper- ation. The Mineral Sands Mining Industry in New South Wales is successfully working within the State's environmental framework and is meeting; community requirements and expectations concerned with the environment and mine rehab- ilitation. Keywords: Environment, mineral sands mining, mine rehabilitation, revegetation.

Jan 1, 1986

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

East Nelson and Marlborough, in the northeast of the South Island, contain a wide variety of metallic minerals, including gold, silver, copper, chromite, antimony and scheelite, but no sustained metallic mining industry has evolved. Gold was the most sought-after mineral during the first century of European settlement and numerous discoveries were made but these failed to live up to expectations. While traces of gold are widespread in east Nelson, including in quartz veins in Nelson City, no payable deposits were found. In Marlborough the probability of a gold discovery had initially seemed remote but all this changed with the finding of rich deposits in the bed of the Wakamarina River in 1864, which provided a much-needed boost to the provincial economy. However, the decline of gold mining in Marlborough began virtually as soon as it had commenced. Extensive floods in 1865 hastened the exodus of miners to the profitable new fields of the West Coast.

Jan 1, 1993

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

By P Hartlieb, M Noeger, M Varelija

Rock bolts are important in underground mining as they provide support to the rock mass around the excavation. They are the most common reinforcement method in mining and civil engineering excavations. The length of the bolts, types and spacing between them can be varied, depending on the reinforcement requirements and the use case (Kolapo, Onifade and Praise, 2022). The rock bolt provides safety and stability for the rock mass in the excavation area and they can be mechanically anchored, grouted, or friction anchored. They normally don’t have a measurement option and there is a possibility that it failed without showing visible signs on the surface, especially in grouted rebar bolts where they can still have some residual strength. Therefore, support functionality can be lost without recognising it. To overcome that, sensors can be installed on all three previously mentioned bolt systems. Intelligent bolts with implemented measuring systems have a function of showing changes and indicating if there is some damage on the bolt. So, it can be said that intelligent rock bolts are regular bolts equipped with additional instruments which are helping us detect potential instabilities inside of the rock mass or malfunction of the bolt itself. Changes in rock mass can be tracked, by measuring rock bolt reaction concerning the excavation response. Rock mass damage and instabilities are therefore measured in terms of rock mass deformation. Moreover, other additional information depending on the type of the sensor device could be collected. Based on such measurements, information about rock mass state can be derived. Different rock bolt types work at different reaction principles. Therefore, limitations on sensor application and information that can be extracted must be considered.

Sep 1, 2024

Computerisation of mine planning activities, specifically in the areas of geology, design and surveying, has been in progress for a number of years in underground metalliferous mines. The combined capabilities of hardware and software have only recently reached the levels necessary to fully support integrated mine planning computer systems in a graphical three dimensional environment. Despite the apparent capabilities of systems now on the market, many sites retain significant parts of their older paper based systems, and employ a mix of two or more software packages. This paper examines what underground metalliferous sites are doing in this area in Australia, and discusses the factors which are inhibiting full implementation of fully integrated computerised systems. Future directions for further developments in the field are also briefly discussed.

Jan 1, 1995

By Y D. Jeon, K S. Kim, C-H Eom, C M. Yoon

The carbon neutrality continues to require reduction of carbon usage in ironmaking and steelmaking processes. Specially, it is expected that the hot metal ratio (HMR) in the steelmaking process should be reduced essentially. Unfortunately, the reduction of the HMR in converter can bring about poor environment for nitrogen removal from molten Fe. From this situation, nitrogen prediction model has been developed to understand the fundamental of behaviour of nitrogen and quantitatively interpret its content changes in the converter process. Thermodynamic and kinetic approaches were improved based on existing mathematical model and attempted to predict nitrogen content in realtime by combining process data. In present study, heat supply from the oxidation (mainly carbon and silicon) and CO evolution in the converter are considered, and scrap melting due to the heat transfer from the molten Fe to the solid scrap charged in the converter also be considered.

Aug 21, 2024

The last decade of national water reform implementation has improved the availability and efficiency of water source allocation in Western Australia. However, it is critical to recognise that the concurrent mining boom witnessed the approach of full water allocation limits, and increasing trends in mineral processing, water infrastructure costs, and wastewater management costs. Water supplies are commonly viewed as absolutely critical to project feasibility in mining, industrial and energy generation projects, even if considered 'non-core business'.   An increasing density of mining projects and industrial estates in Western Australia (WA) creates an opportunity for water infrastructure cost sharing and synergies. The WA government and its agencies have given preliminary consideration to the establishment of independent water utilities in the goldfields (Kalgoorlie), the Pilbara, and Collie regions, and in the Kwinana Industrial Area. The impending Oakajee industrial area and Mid West regional development, and Anketell port in the East Pilbara, could also be considered for common non-municipal water supplies.   The critical issue of apparent commercial risk due to the large scale of water demands and the low customer numbers in the minerals sector relative to other water markets is expected to mandate government partnership in any non-municipal water utility ownership. The commercial feasibility risk is observed as a risk to water supply security for potential mining and industrial customers. Absence of proper water infrastructure planning and governance has the potential to create infrastructure access issues as observed for Pilbara rail developments under the Trade Practices Act 1974.   Other aspects of water cycle management which could be addressed by a non-municipal utility include resumption of mine dewatering water (required changes to WA legislation that are progressing) and consolidated wastewater management for maximising synergy or reuse opportunities and minimising cumulative environmental impacts.   Address of water infrastructure planning for non-municipal water demands must cover commercial and environmental sustainability outcomes to successfully progress minerals sector growth in the State.

Jun 1, 2010

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

Twenty years of effort in developing the use of computers in the design and control of mineral treatment circuits has resulted in a sound base for future widespread application of the techniques.. The intent of this paper is to speculate to some extent about future applications of computer related techniques in the mineral extraction industries. The use of simulation methods for the analysis and design of circuits is discussed. In the area of process control, computers have been largely devoted to process monitoring and reporting tasks. The application of computers for the total control and optimization of complete plants is considered. Finally, the role of computer based modelling studies for definitions of optimum treatment flowsheets is suggested.

Jan 1, 1985

By D J. Hill

"Mining companies routinely invest in improvements to their processing operations, but often these enhancements do not work to full effect.Improvements can be ineffectual because underlying process problems are not identified or prioritised for correction or repair.This is frequently because ‘black box’ solutions deployed to implement process control improvements typically rely on instrumentation to provide data for algorithms to work effectively, and these solutions are often ineffective or disabled at mineral processing sites.There are three key reasons they can fail to deliver: vital instrumentation is not calibrated or functioning as required basic process control and loop tuning was not implemented correctly or is in need of tuning there is an inability to support the ‘black box’ solutions on-site.Many of these problems can be overcome by implementing operational analytics that identify where problems are occurring and prioritise where improvements need to be made.Incorporating operational analytics into process improvement is not a new methodology. It is more a back-to-basics approach to make more efficient use of capital and systems already deployed.Data collection systems, such as the OSIsoft PI System, provide real-time and historical process information for process control experts to analyse and identify areas for improvement. However, most systems are not used effectively. With some simple enabling, data collection systems can provide evidence for prioritising investments in improvements and determining an investment’s effectiveness.MIPAC advocates that the initial step, with analytical evidence, is that clients review the control strategies and implement small influential instrument repairs/calibrations and operator training. This can significantly boost process productivity without the need to spend large sums of money on new capital or employing expensive, difficult to maintain ‘black box’ solutions.A simple Stage-Gate®-style approach ensures that small investments in evidence-based process improvements deliver significant benefits to mining operations.CITATION:Hill, D J, 2014. How to prioritise process improvements, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By J Szymanski, S Planeta

Extensive rockfill cylinder testing was performed to determine the effect that aggregate size, aggregate moisture, Portland cement, fly ash and cement dispersant addition has on compressive strength of a cemented backfill. In this paper ætwo-level factorialÆ and æcentral compositeÆ designs were used to determine the single and interaction effects that each factor have on the overall strength. The results from the designwork indicated that the per cent of aggregate fines had the greatest influence on the compressive strength of the rockfill cylinders. From the factorial design results, a compressive strength estimation equation was derived, which enables the strength to be estimated, given varying input values.

Jan 1, 1998

By W Lu, D Wang

Study of coal oxidation at low temperatures forms the basis of investigating the inherent properties of spontaneous combustion of coal. In general, the process of coal oxidation at low temperatures is very complex, involving many factors. Experiments examining the properties of oxidation and ignition of coal have been carried out. Based upon the results of these experiments, the catastrophe properties in the process of coal oxidation are analysed and the mechanism of catastrophe is proved for the ignition of coal. A folding catastrophe model is also established for the process of coal oxidation. Results obtained show that the process of coal oxidation to ignition is discontinuous, where the coal-environment system yields structure destabilisation. The system can jump from one stable attractor to another. The research results presented in this paper help to show the irregularities of coal oxidation at low temperatures and how to pursue effective control measures.

Jan 1, 2005

The large El Cerrejon coal open pit in north east Columbia has been developed over the last decade in a remote, entirely new mining area with hitherto unskilled inhabitants. Now over 200 pieces of heavy equipment operate with high reliability and availability due to successful theoretical training and skill improvement programs tuned to the specific reliability needs of the worksite and environment. The process of continuous improvement adopted promises further competitive advantages of the project.

Jan 1, 1991