Search Documents

The purpose of this paper is to provide a ælook behindÆ the Coal Mine Health and Safety Act 2002. The more important policy considerations in the development of the Act are described along with a summary of the main provisions of the Act. The Act, together with supporting regulations and other instruments will formalise the use of risk management as a necessary discipline in the systematic management of occupational health and safety. It must be recognised that the purpose of this paper is not to provide a legal interpretation of the legislation nor is it to provide legal advice. Rather, the main purpose is to provide some indication of the underlying intent behind the Act.

Jan 1, 2003

By E Philippa, J Vitanza, C Hawtin, B Miller

B Miller , E Philippa , C Hawtin and J Vitanza

Mar 22, 2022

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955

To solve the mining safety and health needs of the future, access to, and sharing of, timely and relevant information will be crucial. The next generation of the Web will provide tools (RDF, OWL, SPARQL, etc) to define and link content for more effective discovery, integration, and reuse across applications and organisations. A recent Gartner Research Report (Finding and exploiting value in Semantic Web technologies on the web, May 2007) predicts these technologies will begin to coalesce in ten years. Implementing this Semantic Web requires structured web content described via metadata (information about information). If an industry or enterprise bases its metadata on a common vocabulary, it becomes possible to share and reuse information. The National Institute for Occupational Safety and HealthÆs (NIOSH) Mining web site provides access to more than 1500 NIOSH-developed publications, products, and topic pages on issues as diverse as ground control, respiratory diseases, and mine emergency management. As the site has grown, locating content has become increasingly difficult. To improve the searching process, a panel of internal experts representing all major research programs was established to develop a controlled vocabulary for indexing that content. The outcome is the NIOSH Mining Safety and Health Thesaurus, a faceted, hierarchical thesaurus containing hundreds of mining safety and health terms organised into 20 facets (eg diseases, injuries and disorders; hazardous events and exposures, equipment, engineering and administrative controls). One immediate goal of this project is to reduce the complexity of locating information on the NIOSH Mining web site by implementing metadata and faceted information retrieval techniques. Another goal is to stimulate discussion in the international mining community regarding developing metadata standards so the industry is ready to adopt future Semantic Web technologies to improve access to mining safety and health information.

Jan 1, 2008

By V Pfannenstiel

The United States (US) coal mining industry has been working under comprehensive planning, operating and rehabilitation regulatory requirements for nearly 35 years. The public desire for environmental protection during mining and rehabilitation following mining to achieve post-mining land use and sustainability goals has been a major factor and continues to influence the process. Mining companies have evolved operations to achieve outcomes that address the desired goals and regulatory requirements cost-effectively and successfully. Over the 35 year regulatory period, requirements for more diverse topography, specialised revegetation communities, landform stability and assured sustainability have increased and become more complex. These challenges are effectively met by maximising integration of mine planning and operating with the rehabilitation process. Rehabilitation is then implemented in a more timely and efficient manner and with effective results that achieve desired outcomes, commonly with added value. Peabody Energy (Peabody) has taken this approach in its US operations and this paper discusses an integrated approach and illustrates learnings and results with examples from several of its western US operations.CITATION:Pfannenstiel, V, 2012. Integrated planning, mining and rehabilitation for effective results and sustainable land use - A western United States perspective, in Proceedings Life-of-Mine 2012 , pp 219-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Two key elements in the design of a pastefill or high density hackfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: I. Vacuum or pressure filters. These represent the 'traditional' approach to the preparation of pastefill. 2. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producing paste/high density backfills. 3. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach. This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material- No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mincsin Canada.

Jan 1, 1998

Downstream value-adding is a strategic issue for a country like Australia, which has a resources-driven sector of a scale that has significant impact on the national economy. The question of why producers are not doing more to ævalue-addÆ is often asked. In Australia this debate takes place within the context of: an era of unprecedented growth in demand for resources driven by the rapid urbanisation of China, India and others;impending legislation and uncertainty around carbon pricing;rapidly rising energy costs;significant supply-side shortages including infrastructure, skills and manufacturing capacity; andsignificant industry consolidation of primary resource producers with commensurate improvements in market power.There are several examples of resource-based industries which have developed their business along the complete value-chain; for example large oil and gas producers successfully span upstream and downstream operations including refining and petro-chemicals as well as retail distribution of fuel and other products. Relevant frameworks that provide insight and understanding into the strategic issues around value-adding are reviewed and examples of the application of these frameworks to companies and industries which have successfully adopted a strategy of integrating along the value-chain, as well as those players who have focused on parts of the value-chain are presented. The issues around value-adding in Australia are then reviewed with reference to these frameworks and it is concluded that the issue is a conflict between the objective companies who wish to maximise financial value versus the desire of governments to increase economic benefits. An approach to aligning these objectives is proposed.

Jan 1, 2008

Bakelite is fairly widely known as a suitable material for the mounting of ore specimens, concentrates and tailings for microscopical study, but has not as yet had extensive application. It is the most suitable mount for specimens which are to be held in the mechanical holder of a polishing machine, based on that described by J. W. Vanderbilt*, which is installed in the Geological Department of the Melbourne University.Bakelite products are prepared by subjecting bakelite powder to a temperature of about 1600 C. under a pressure of approximately two tons per square inch for a period of four minutes. The shape and size of the products are governed by the use of suitably constructed dies. When the concentrate or tailing is mixed with the bakelite powder, a briquette is produced which can be polished so that the opaque minerals in the sample can be examined microscopically in the same way as in a piece of solid ore. A simple machine for the construction of these briquettes has been described by Head and Slavin. It consists of a small four-pillar press in which the pressure is supplied by...

Jan 1, 1933

Addressing community concerns in relation to an economic activity, particularly when it causes significant community impacts, is especially important for the development of extractive industry projects. Pipelines comprise an integral part of many hydrocarbon developments, which may cause different effects on local economic development, communities and the environment compared with open cast mines. This paper explores community impacts associated with a case study of the oil pipeline æEastern Siberia-Pacific OceanÆ in the Republic of Sakha (Yakutia), Russia. Based on semi-structured interviews, conducted in 2006 - 2008 in Russia, the paper investigates claims of local communities about potential impacts of the pipeline development of their environments and economic activities as well as community claims for greater involvement in sharing the benefits from this major infrastructure project. A community of Indigenous people, Evenk, is likely to be most profoundly affected by the development due to impacts on their traditional activities such as hunting and reindeer herding. The paper examines in detail the regional economic, social, environmental and Indigenous peoples concerns over the construction of the oil pipeline and investigates actions and methods adopted by community organisations to voice their concerns about the pipeline development. Finally, the paper assesses the process of interaction between the pipeline developers and regional stakeholders.

Jan 1, 2009

By S Arya, A Bhandari

Dust emissions by blasting are of concern to both mine operators and surrounding communities. The quantity of dust produced, and the effects of its dispersal depend substantially on geological, blasting and meteorological conditions. This paper provides details of methods used to quantify the amount of dust produced after collecting samples using high volume dust samplers, and the difficulties encountered in satisfactory dust sampling and quantification. Also described are practical dust reduction methods by using water filled ampoules and water filled balls.

Jan 1, 2004

By Y, Li Jianxiong, Hu Hua, Gu Desheng

After having briefed the technical and economical advantages of continuous mass mining in underground metal mines, the authors discuss the four stages of research and development of continuous mass mining in China. The four stages are: vibrating ore drawing in a stope, continuous mass mining in a stope continuous mass mining without rib pillars in an area and continuous mass mining in whole mine. The authors briefly review the research achievements of the first and the second stage; Combining the key national research project of the æNinth Five Year PlanÆ ù æThe experiment and research of continuous mass mining without rib pillarÆ, the authors introduce in detail the technological condition of mining, the design ideas of continuous mass mining, the design scheme of mining, the technology of mining. the equipment of mass mining, the chief research achievements and so on. The success of research of continuous mass mining without rib pillar indicates the arrival of the third stage of research. The introduction of continuous mass mining will promote the technology revolution of mining in China remarkably. The authors also point out that the development direction of continuous mass mining of the 21 century is continuous mass mining in whole mine, which is the fourth stage of research.

Jan 1, 2000

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

There are two main challenges in analysis of spectral data: to output as accurate an interpretation of the sample mineral assemblage as possible and to then use the spectral data to map out trends (downhole, across section or traverse) that will assist the exploration geologist to target drilling and further exploration. This paper will discuss methods of extracting the maximum amount of information from spectral data and examples of plotting the information downhole, in section and plan view to assist in exploration and mining. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021

By R Bearman

The importance of crushers in the mining industry declined with the introduction and resultant dominance of AG and SAG based circuits, but the recent move to consider more energy efficient circuits has caused the industry to re-consider the role of crushers.Different types of comminution equipment have different efficiency in the way the energy is applied in the size reduction process. Because of the general trend towards more sustainable production processes and emission of carbon dioxide, energy use has become more important. To fully understand how crushers can contribute to optimising the energy application in comminution circuits, detailed models of process performance are required. Such models need to take into account the mechanical design factors and how the crusher performance changes in response to feed conditions, the control strategy utilised and the wear of the crusher liners.It is also critical to analyse the total circuit, not just the individual crushers. To fully understand the performance of the entire circuit, dynamic simulation should be applied. Without the holistic understanding of the total circuit and the incorporation of transient effects, the full circuit performance cannot be adequately determined and the true energy picture will not be quantified.Based on detailed mechanistic modelling of crushers by the authors and the application of dynamic simulation, the opportunities to optimise the use of crushers for energy efficiency are examined.

Aug 8, 2011

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Aspects and anomalies in the present Standard Specifications for Blended Cements which may have operated in Australia against the development of the greater use of Slag Blended Cements are noted. Estimates of slag and ash usage in Australia are given and the need for further research with local materials stressed.

Jan 1, 1979

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011

By Bertrand D. L

Although investigations into treatment of Mt. Keast (a hill of tailing) began as early as 1940, it was not until the Imperial Smelting Furnace (I.S.F.) was installed at Cockle Creek by Sulphide Corporation that its treatment became eooncmically feasible. Early investigations and milling operations which began in mid-1976, with their developments are described. Metal recovery involves sulphide flotation, oxide flotation and gravity techniques.

Jan 1, 1983

By J Kwak

Driving sustainability concepts and practices into the heart of the design process is the key to achieving a successful, sustainable plant design. Engineering design practices, tools, systems and methodologies should be prepared around true eco-efficiency parameters, adopt wholesystems-thinking and consider life-cycle impacts for the design task. Experience dictates that the application of sustainable plant design practices is most likely to succeed if: The principles are well documented and explained. All stakeholders agree on what sustainability means. Sustainable plant design is treated as a core process. The principals of sustainable plant design are equally applicable in brownfield and Greenfield environments. Although brownfield situations provide the designer with less latitude for change, these types of projects do allow easier measurement and demonstration of relative impacts. This paper further develops the above points by drawing on case studies from HatchÆs repertoire.

Jan 1, 2004