Search Documents

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By M Higgins

Measurement while drilling (MWD) techniques can provide a useful tool to aid drill and blast engineers in open cut mining. By avoiding time consuming tasks such as scan-lines and rock sample collection for laboratory tests, MWD techniques can not only save time but also improve the reliability of the blast design by providing the drill and blast engineer with the information specially tailored for use. While most mines use a standard blast pattern and charge per blasthole, based on a single rock factor for the entire bench or blast region, information derived from the MWD parameters can improve the blast design by providing more accurate rock properties for each individual blasthole. From this, decisions can be made on the most appropriate type and amount of explosive charge to place in a per blasthole or to optimise the inter-hole timing detonation time of different decks and blastholes. Where real-time calculations are feasible, the system could extend the present blast design even be used to determine the placement of subsequent holes towards a more appropriate blasthole pattern design like asymmetrical blasting.

Jan 1, 2001

By E Widzyk-Capehart, T Bednarz, O Daud, N Cutmore

The interest of industry, in particular future mining, is pointing towards the use of novel visualisation systems to improve the operational efficiency of user interfaces. While the technologies used to enhance operators’ experience are advancing, the implementation of novel visualisation paradigms within mining operations is trailing behind other industries, particularly health and aviation. In this work, we present a number of initiatives and use cases of immersive virtual and augmented reality systems that can fit within the mining context. These ideas represent a step towards new platforms that might increase the efficiency and safety of mining operations through applications such as 3D panoramic video monitoring technology with annotated information coming from big data analytics and visual analytics processing engines. However, while the technologies are used in a variety of training settings, their application in the working environment is lagging behind. This paper presents examples of scientific visualisations that could be applied in a mining context to extend the possibilities of operators’ cognitive abilities and working efficiency. They are intended to foster a discussion within the mining community to move beyond the training realm and into the operational environment.CITATION:Bednarz, T, Widzyk-Capehart, E, Daud, O and Cutmore, N, 2015. Effective immersive visualisation systems for mining applications and beyond, in Proceedings Third International Future Mining Conference, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Forty two new apatite and zircon fission track analyses on the Kubor-Marum-Bena Bena area of northern Papua New Guinea severely constrain the timing of tectonic events and hence the tectonic models for New Guinea, particularly arc-continent collision. In addition, the data can be analysed regionally in terms of known and assumed lithospheric fault zones inferred to control mineralisation (eg. Corbett 1994; Kendrick et al 1995; Hill et al 1996) to determine reactivation of these zones. When combined with the new kinematic plate models for the evolution of New Guinea (Hall 1997) there is the potential to predict likely zones of mineralisation. The low-medium grade? Palaeozoic rocks of the Bena Bena terrane yielded a zircon fission track age of 17 Ma, indicating the time of cooling below 200¦C. The age is consistent with `the shift, at about 16-18 Ma, from volcanolithic sediments to mixed provenance sediments rich in quartz and metasedimentary lithic fragments in the southern Finisterre Ranges (Abbott et al. 1994). This shift was recorded in the Sukurum Formation, which ranges in age from Middle Miocene to Pliocene with quartzose and metasedimentary grains in all samples. Although recording rocks at temperatures of 200¦C and hence depths of ---5km, the 17 Ma age suggests the Bena Dena terrane was rapidly cooling at that time due to uplift and erosion, supplying metasediments to the southern flank of the Finisterre Range, currently 100 km to the east. Significantly, the Middle Miocene Akuna Intrusive Complex, dated 14-17 Ma by Page (1976), lies almost entirely within or adjacent to the Bena Bena terrane. Potentially the uplift, erosion and cooling of the terrane at 17 Ma may have been caused by the rising plutons. If so the 800 sq km exposure Akuna Intrusive Complex at the SE end of the Bena Bena terrane may have been the focus of uplift and supplied the metasedimentary detritus to the Finisterre Range. This suggests that the Finisterre Range was not far removed from the Bena Bena terrane, perhaps less than the 200 - 400 km indicated by Abbott et al (1984). The Akuna Intrusive Complex probably resulted from subduction of the Solomon Sea Plate beneath the PNG margin. In order for the subducted slab to reach depths of -100km below the area to facilitate partial melting and plutonism (Hamilton 1994), subduction probably commenced 3-5 Ma Ma before plutonism, ie at or prior to 20 Ma suggesting a significant change in the tectonic regime at -20 Ma, perhaps related to collision of the Solomons - Ontong Java Plateau collision (eg. Hall 1997). The main result to emerge from the 28 apatite fission track analyses is that the whole of the study area underwent rapid cooling due to uplift and denudation in the Late Miocene, mainly between 7-10 Ma. Results from several samples indicate that they were not totally overprinted prior to uplift indicating maximum burial of -3 km in the Middle Miocene, assuming normal temperature gradients. The burial is less if higher gradients are assumed, allowing for Middle Miocene plutonism. The Late Miocene cooling in the Mobile Belt agrees well with the Pliocene to Recent cooling in the Fold Belt to the SW, interpreted to be due to uplift and erosion associated with fold and thrust deformation of the Miocene Limestones (Hill & Gleadow 1989). This timing relationship suggests, that compressional deformation in the Mobile Belt occurred in the Late Miocene, at 105 Ma, and that the deformation migrated towards the undeformed foreland in the southwest in the Pliocene, at 5-2 Ma. The regional Late Miocene uplift and denudation in the Mobile Belt is also consistent with that postulated by Crowhurst et al (1996; 1997) for northwest PNG, although they considered the event to have occurred mainly from 8-5 Ma. If so, then the uplift and denudation may have been migrating from east to west as well as to the south into the Fold Belt. These timing relationships place significant constraints on tectonic models for the area, indicating that the major compressional pulse in PNG commenced in the northeast at -10 Ma and migrated to the southwest and west in the latest Miocene to Pliocene. This suggests that the initial arc-continent collision and associated shortening occurred in the Late Miocene around -10-12 Ma. This immediately followed intrusion and cooling of the Akuna Intrusive Complex at -17-14 Ma and the Bismarck Intrusive Complex at -12.5 Ma (Page 1976), indicating a linkage between the end of plutonism and the start of compressional deformation. The timing is consistent with the observation of Hamilton (1994) that in areas of subduction `the common regime in overriding plates is extensional and leading edges are crumpled only in collisions. This suggests that the Middle Miocene magmatism in northern New Guinea occurred during extension above a subducting slab and was terminated by Late Miocene arc collision and resultant compression commencing at -10-12 Ma. In general, these data indicate that the acme of denudation and cooling in the Mobile Belt was in the Late Miocene, with relatively little denudation there since. In contrast, Hill & Gleadow (1989) found that the peak of denudation in basement outcrops in the Fold Belt was in the Pliocene at -4 Ma. However, in this study some samples from the Mobile Belt yielded Pliocene ages or high

Jan 1, 1997

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

Edie Creek is located in the Morobe Goldfield about 17km by road from Wau in the Morobe Province of Papua New Guinea (PNG). Four distinct periods of mining development have occurred since discovery of rich alluvials in 1926. During the two years following discovery, individual expat-riate miners with gangs of native labourers mining rich alluvial gravels dominated the field. After the discov-ery of hardrock mineralisation in 1927, companies accumulated leases and devel-oped extensive underground mines and mechanical processing plants at Day Dawn Mine and Edie Creek/Karuka Mine between 1929 and 1942. After the Second World War, the underground operations were not re-opened, and mining activ-ities mostly concentrated on working alluvial and eluvial deposits. From 1962 onwards, Papua New Guinean miners became increasing producers as company activities declined. In 1990, Edie Creek Mining Company Pty Limited, a joint venture company involving Wau landowner groups commenced operations on New Guinea Goldfield's leases. It currently mines by open pit methods, rich quartz stringers and is invest-igating the open pitting of the Edie Creek/Karuka underground workings.This paper describes the mining and processing techniques employed during the various phases of develop-ment at Edie Creek in the past 70 years. The problems and hardships of operating on a new and remote goldfield are outlined.Abstract

Jan 1, 1994

By S Walters

The emerging discipline of ‘geometallurgy’ is not new but is becoming increasingly recognised as a discrete and high-value activity. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance behaviours. A key outcome is enhanced economic optimisation of mining and improved risk management tools.Industry recognition of the need for large-scale, integrated research to support this emerging area resulted in commencement of a major ongoing initiative in mid-2005. The AMIRA International P843 ‘GeMIII’ project (Geometallurgical Mapping and Mine Modelling) is a cross-discipline collaboration involving a number of world-class research organisations supported by over 20 industry sponsors.The project is delivering integrated tools and methods which link intrinsic rock characteristics to prediction of mineral processing performance. These indices must be capable of spatial distribution in 3D resource models and incorporation into mine planning and optimisation. A key aspect is provision of new cost-effective tools and methods which can provide the large numbers of measured and estimated data points required to undertake effective modelling and spatial distribution. The integrated methodology and enabling technologies being developed through the ongoing AMIRA GeMIII project are outlined, together with implications for supporting industry best practice.

Sep 5, 2011

By C Lutherborrow

The Sangdong Tungsten/Molybdenum Deposit is located in the Republic of Korea and was discovered in 1916. At this time Korea was a colony of Japan. It was mined for two years after discovery closing in 1918. Full production recommenced in 1933, and from that point until 1945, it was the major source of tungsten for armour plate for the Japanese military. After World War 2 the US government ran the mine until late 1946. The mine operation then passed to Korean ownership but production ceased during the Korean War and did not recommence until late 1953. The mine ceased operation in 1992 due to low metal prices. From the late 1960s to the time of closure, Sangdong was the largest tungsten mine in the world (Kim, 2002). An understanding of changing mining methods over time has been critical in assessing the potential of redeveloping the Sangdong Deposit.

Aug 22, 2011

In December 1997, a series of new environmental legislation was enacted including:ò Environmental Planning andAssessmentAmendmentAct 1997; ò Contaminated Land ManagementAct 1997;ò Protection of the Environment (Operations) Act 1997; ò Native Vegetation Conservation Act 1997; andò Pollution Control (Load Based Licensing) Act 1997.These new Acts will have varying degrees of impact on the coal mining industry in New South Wales when they commence later this year.

Jan 1, 1998

Drilling underground can be a hazardous undertaking in many circumstances. Raiseboring and boxhole boring underground could form an integral part of the block caving production methodology and getting the right mix of technical capability, ergonomics and economical viability has been the goal of many machine manufacturers. With the introduction of the Terratec Universal Boring Machine concept, flexibility of raiseboring, downreaming and boxholing has been enhanced by the introduction of a single machine that will perform all three processes. In addition to its technical flexibility, additional safety features have been introduced that will eliminate many sources of injury by mechanising most of the operational procedures. Together with the one-man remote operation, this machine design addresses and solves many of the safety issues. This paper outlines the machine concept, details its safety features and shows the techno-economic advantages for use in the block caving environment. Block caving is a distinct caving method applied mostly to large massive orebodies because of the inherent low costs and high production capabilities. Areas of sufficient size are mined by undercutting so that the mass above will cave naturally. Extraction of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling (Figure 1).

Jan 1, 2000

The space probe Magellan is on its way to Venus (May, 1989) and with its sophisticated radar systems will discover much more about our twin planet. There is tennuous evidence that Venus once had liquid water. Did it have life? Why was it not stable and why did liquid water not persist through the period of the dimmer young Sun? These are profound questions for us. We understand why Mars froze when volcanism terminated (Just as Earth will freeze one day) but could Earth boil if we continue to add greenhouse gases (Broecker, 1985). What will happen if 10 billion humans continue to use fossil carbon as their main fuel source? The Earth is warming fast and the new satellite data show that the oceans are warming faster than we thought. Is this just a fluctuation or is the greenhouse signal coming through the normal noise of climate?

Jan 1, 1990

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By Gottlieb P, Sutherland D, Jackson R

The QEM'SEM system for automated image analysis of mineral samples is described. Details of the equipment are given together with information on the methods of measurement. Finally some practical applications are described where QEM*SEM has been used for the solution of metallurgical Problems.

Jan 1, 1989

By M Slight, H Lacy

In recent times, with the global mining industry’s focus on sustainable development there has been a significant focus on mine closure and rehabilitation performance and reporting through the development of the International Council on Mining Metals (ICMM), the Global Reporting Initiative and the Equator Principles. In addition, financial reporting obligations under International Financial Reporting Standards and the Sarbanes Oxley Act (2002) have also led to better understanding and improvements with industry closure performance, liability management and reporting.Under these sustainable development principles and financial reporting obligations, mining companies are required to consider mine closure planning and associated cost estimates across all life cycle phases of the mine. Internal processes have been developed within mining companies to better understand their closure liabilities and obligations and likely costs and cost estimating processes are generally developed for long-term life-of-mine (asset) planning and budgeting, financial reporting for corporate balance sheet provisioning purposes, and regulator reporting for environmental bonding and financial assurances.These days mining companies need to plan for, prepare and actually mine for closure right from the start of a project. This means that their closure and rehabilitation liabilities throughout each stage of the mine life cycle phases must be understood, planned for, managed and controlled.So how is the industry performing? Understanding of closure liabilities is improving and reflected in liability cost estimations that are recognising the likely issues to be faced at closure, but there is a way to go to ensure that the industry doesn’t add to the increasing legacy liabilities being passed onto the wider community.CITATION:Slight, M and Lacy, H, 2016. Closure liabilities – where are we at?, in Proceedings Life-of-Mine 2016 Conference , pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By G J. Lyman

Sampling of grain for mycotoxins is challenging in that some mycotoxins, such as Ochratoxin A (OTA), have very low permitted levels and the kernels carrying the mycotoxin may be highly localised within the bulk of the grain as ‘hot spots’. Sampling for genetically modified organisms (GMOs) can be fraught with similar problems, especially if the contamination is adventitious and random. Incremental sampling under these circumstances can be shown to lead to a high variance in the sampling result.A new design of sampler for grain and other free-flowing particulates has been developed that is effective in practically eliminating the sampling variance due to distributional heterogeneity (DH).This paper introduces the design and argues that the sampler should be free of sampling variance due to DH.CITATION:Lyman, G J, 2017. A new sampler for grain and other free-flowing particulates, in Proceedings Eighth World Conference on Sampling and Blending , pp 277–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

A variety of algorithms and methods are being used by the mining industry today to map mineral resource for reserve estimation. The traditional methods including Polygonal, Sectional and Inverse Distance methods are relatively easy to understand and implement. They have served industry well for several decades and should continue to do so for the large bulk mineable deposits with very regular geometries with relatively small variation in grade.

Jan 1, 1992

There was a time, in the memory of some here tonight, when the annual meeting of The Institute was a nostalgic occasion. Often, in the 1920s, there was comment on the decline of Australian mining and on the lack of new mineral discoveries. When some of our Presidents prayed then for a new Bendigo, and instead were given a Mount Isa, they were justifiably disappointed because of the vastly different capital requirements.In 1967 the mining picture is very different. The recent mining developments in Australia are certainly as important as several Bendigos and several Kalgoorlies. The mining industry in Australia has never been more dynamic than today (Table 1). And if we ask why it is so dynamic, the answer lies in the role which overseas capital is playing in the industry. The contribution of overseas capital should concern us not only because we are members of the mining and metallurgical profession, but also because we have a duty to make our profession contribute as much as possible to the well-being of Australians. It is not sufficient to argue that overseas capital is good for the mining industry; we must also examine whether it is good for the economy and the nation. In this context the current criticism of the inflow of overseas capital into Australian mining is useful, for it gives us an opportunity to see what has resulted from the inflow.In discussing this question I do not suggest that we emulate Captain Hancock, that legendary Moonta mine manager who, according to Oswald Pryor's cartoon, used to say to his miners: "When I say a thing is, it is, even if it isn't". The question can only be discussed on a factual basis; and I would submit that many of the important facts relating to overseas capital in our mining industry are often overlooked or ignored. I would further submit, on the basis of these facts, that Australia's present day mining industry has been largely built on overseas capital and that the overall benefits of that capital to Australia have been enormous.

Jan 1, 1967

By R Urie

Dilution and loss of ore during the mining process invariably occur in all underground mining operations. This dilution and ore loss can have a significant effect on the performance and value generated from a mining operation. Further, excessive dilution or greater than anticipated ore loss during mining is often one of the key reasons for the underperformance of a mining project when compared to a feasibility study or annual budget. Mining professionals often go to great lengths preparing detailed mine plans, schedules and economic models only to then apply high-level estimates or rule of thumb values for dilution and mining recovery that can ultimately lead to inaccurate forecasts for the performance of a mine with the resultant loss of value due to the mining of uneconomic material or the loss of potentially valuable ore. This paper discusses processes and practices that can be practically used to manage dilution and mining recovery in an underground mining operation with a focus on understanding and then maximising value. The processes cover items such as the definition and measurement of dilution and mining recovery, techniques for the estimation of dilution and mining recovery, consideration of the economic implications, management of dilution and mining recovery through the stages of the planning cycle, and practices to reduce dilution and improve mining recovery. Common misconceptions and omissions are also discussed.

Mar 29, 2023