Search Documents

Segregation of granular material is a very common phenomenon. Realised in a forced manner it is a basis of all separation processes in mineral processing, mainly classification and beneficiation. Spontaneous segregation, occurring under dynamic conditions and making possible mutual translocations of grains, is however an undesired phenomenon as a rule. It decreases the degree of blending of the material which in many cases is an important technological feature of the material. It should be noted that the segregation can be treated as the reverse phenomenon to blending. The importance and frequency of spontaneous segregation has caused many rules and technical solutions to be developed aimed at decreasing the possibility of the spontaneous segregation. However, not enough attention has been focused on an quantitative description of the phenomenon of segregation, either to ways of quantitatively evaluating segregation effects or to explanation of the influence of conditions under which the grained material exists on the occurrence of segregation and its degree. The paper presents the following topics: 1. new numerical indicator for evaluation of the segregation degree (and blending) of material contained in an arbitrary determined region is proposed; it is determined relative to the maximum possible degree of segregation of the given material when taking into account its individual properties; values of the indicator can be calculated effectively for an arbitrary material, also for ulticomponent material. 2. there is proposed a way of evaluating the state of segregation (or blending) of material in an arbitrary part of the region mentioned above, based on investigation of the gradient of distribution of the material features; algorithms of analytical procedures and calculations are presented for typical cases met in mineral processing; 3. results of initial experimental studies, both laboratory and industrial, concerning the effect of the chosen factors occurring in transport and storage of the material on its degree of segregation are presented; and 4. conclusions referring to the fundamental and practical significance of the results are also presented.

Jan 1, 1993

Because of the coincidental location of orebodies and population in Australia, the mineral sands industry has been subjected to numerous land use conflicts, resulting in the sterilisation of strategic ore reserves and a severe downturn of activity in the eastern states. All tiers of government of various political persuasions were responsible for the decisions leading to this sterilisation. As such, it became a community response to intense land use pressure along an attractive and popular coastline. The resultant high public exposure of the industry has placed it in the forefront of developments in rehabilitation technology. In eastern Australia, the industry has operated in a wide range of ecosystems, many with conservation values. Rehabilitation ech- niques have been developed to suit these varied conditions, and much of this technology is now widely adopted throughout the mining industry. Land use considerations in Western Australia are somewhat different to those of the eastern states. Nevertheless, the same basic principles of rehabilitation apply with modification to suit local conditions and land use objectives. The development of rehabilitation in both Eastern and Western Australia is reviewed, and the direction of future trends is indicated.

Jan 1, 1986

By Cooper W. C, Stokes M. A

Proterozoic gold deposits in the Pine Creek Geosyncline are at present receiving renewed attention with the opening of old mines and several new discoveries. This important polymetallic province contains occurrences of gold, base metals, tin, tungsten, tantalum, platinum, palladium and aluminium. These resources have been exploited over the past century with periods of major interest during the turn of the century and during the past 20 years. Economically viable resources of predominantly gold, eg Pine Creek, Woolwonga, Brocks Creek and Union Reefs, and Ag-Pb-Zn, eg Woodcutters are currently in development or being mined. A variety of genetic models, ranging from magmatic through hydrothermal to syngenetic, have been postulated in the past for the formation of gold deposits in the Pine Creek Geosyncline. The first discussion on the regional geological factors that control ore deposition in the Brocks Creek-Howley District was by Sullivan and Iten (1952). They recognised that the most important ore deposits are associated with anticlinal and domal structures and that granites may be a controlling factor in the localisation of the mineralisation. More recently a group of authors, Needham and Roarty (1980), Goulevitch (1980), Nicholson and Eupene (1984), Sanger-Von Oepen, Friedrich and Kater, (1988), Nicholson and Eupene (1990) and Kruse, Whitehead and Mulder (1990) have suggested an exhalitive syngenetic origin, or remobilised syngenetic during dolerite intrusion and/or regional deformation, for gold mineralisation, especially those associated with South Alligator Group lithologies (eg Bridge Creek, Mt Bonnie group of mines and Cosmopolitan Howley). Studies carried out at the Bridge Creek and Western Arm Prospects over the last three years suggest that syngenetic models for gold mineralisation are less relevant to gold mineralisation in the Howley District than first thought (Wall, 1989; Partington, 1990). The Bridge Creek prospect has been cited as an example of a syngenetic-syngenetic remobilised deposit (Oepen, Friedrich and Kater, 1988) while the Western Arm prospect is more clearly a vein hosted epigenetic deposit and a comparison of the styles of mineralisation at both prospects will be made. The nature of the gold mineralisation at both prospects will be described and compared, and possible genetic models for gold mineralisation and their relevance to regional exploration discussed.

Jan 1, 1994

By W Y. Guo, L X. Chen, D X. Zhang

To obtain the rock type-I crack propagation process accurately, a novel fixture is used to make the prefabricated crack of rock propagation along the predetermined direction. In this study, the crack propagation process of rock is monitored with the digital image correlation method (DICM), and a mechanical model of crack directional propagation was established. The results show that the simple crack directional propagation device can effectively realise the stable propagation of type-I crack along the predetermined direction, the crack initiation angle is less than 10°, and the deviation between the peak strength of crack propagation calculated by a simplified mechanical model and the tensile strength of Brazilian splitting is 22.76 per cent and 7.53 per cent, respectively. According to the deformation field evolution law, crack propagation can be divided into three stages: microcrack development, main crack propagation, and main crack propagation. As for the rock type-I crack initiation and propagation mechanism, before reaching the peak strength, the prefabricated crack tip is subjected to maximum tensile stress; the elastic energy increases rapidly, and the dissipation energy increases slowly; after the peak strength, elastic energy exceeds its energy storage limit and released rapidly, and most of the input energy is converted into dissipation energy, which makes the crack propagation rapidly. The crack directional propagation device will be further optimised and improved, and it is expected to provide a new method for the study of crack propagation mechanism, rock failure precursor information and crack arrest principle, etc. It will also provide theoretical references for the optimisation of coal strata directional blasting, fracturing, fracture arrest, and other related technologies in geotechnical engineering.

Nov 29, 2022

The Prospero orebody is a part of the Helene mine at Cosmos and was scheduled to begin production in March 2008 after the exhaustion of the Tapinos orebody in the same mine. Treatment of the Tapinos orebody was challenging and it was envisaged that Prospero would have similar properties given that it was also anomalous in deleterious elements and would be of a similar mineral hosting. It was deemed necessary to undertake a metallurgical test work program to identify any potential processing issues, complex mineralogy or significant metallurgical domains. The paper discusses the processes which were employed to undertake the metallurgical test work program and describes the aspects that can be employed by other developers to quickly and effectively assess potential future orebodies. It will demonstrate that the work was successful at determining expected metallurgical behaviour, providing direction for mining operations and highlighting areas for more extensive research.

Jan 1, 2009

By A H. Hofstra, G P. Landis, P Emsbo, A G. Hunt

Models of the evolution of the hydrothermal systems that form porphyry Cu (Mo-Au) deposits are compromised because aqueous magma-derived fluids in the ore zones of most deposits have changed from their original magmatic compositions as a result of cooling, depressurising, mineral precipitation, brine-vapour unmixing and fluid-rock reactions. However, in deep quartz-rich, sulfide-poor veins from numerous porphyry type deposits, we have identified parental fluids trapped in inclusions at near magmatic temperatures and pressures above the brine-vapour unmixing solvus. We have analysed these inclusions for bulk salinity, density, solute chemistry, helium isotopic ratios and elemental composition. These parental inclusions contain 35 - 70 volume per cent bubble, are low to moderate salinity, contain up to ten mol per cent CO2, and commonly contain a chalcopyrite daughter crystal. Our results indicate that these Cu-rich fluids transport Cu from a plutonic complex below upward into a hydrothermal system, where decompression, cooling, unmixing and water-rock reaction drive ore-mineral precipitation. Na/Cl ratios greater than one indicate that in addition to chlorine, sulfur and/or carbonate must play a key role in Cu transportation. Helium isotope ratios indicate that between ~15 and 100 per cent of helium in these fluids is mantle-derived. We suggest that in addition to He, volatiles from mafic magmas in the mantle are also likely to supply CO2, Cu and S to the fluids that form porphyry copper deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Industrial relations on Australian and New Zealand resource projects can be volatile. Therefore investors have become increasingly aware over the years that sound industrial relations during construction is vital to the overall success of their project. There has been a wide range of actual industrial relations performance, project by project, and the degree. of success often directly correlates with the degree and thoroughness of pre-project planning. However, although many projects have been crippled by delays and cost overruns because of labour disputes, good results are achievable. Total commitment to the project by all parties involved is essential and it is up to the employers to seek out this commitment and not just trust mother luck. Industrial relations must be taken very seriously as the price of failure can render a resource project unviable.

Jan 1, 1983

By J Jackson, D C. Curry, A C. Keith

Australian Bureau of Statistics (ABS) data shows that since 2006 the balance of capital costs associated with mine development has become weighted greater than 75 per cent to enabling infrastructure and less than 25 per cent on process plant, equipment and machinery. The well-developed mine planning techniques including pit optimisation and scheduling and process plant design and optimisation have typically proceeded in a linear fashion from geology, mine planning, through processing, with some iterations back to the mine. Only then is attention paid to planning and costing of enabling infrastructure in any detail.Optimisation has typically involved developing cut-off grades, mine plans and schedules and ore processing that produces maximum economic ore. Infrastructure has then been sized æto suitÆ the mining and processing core business drivers.What the ABS data, together with global trends, indicates is that infrastructure can no longer be an afterthought if miners wish to achieve robust project value estimates, realistic ore to market costing and resource statements based on achievable economic cut-off grades.In addition, with such a large proportion of the costs originating from non-mining or processing activities, a mining operation can only be truly optimal if these aspects are given due consideration in the mine design stages, based on quality geometallurgical inputs so that the size and cost of enabling infrastructure is optimised to maximise project value.This paper outlines an iterative holistic approach to mining project development, which integrates the geometallurgical approach and enables infrastructure planning into project design and evaluation. It presents case studies showing reduced overall costs, increased net present value (NPV) and reduced project delivery timelines.CITATION:Curry, D C, Keith, A C and Jackson, J, 2013. Is a 2.5 per cent success rate good enough? Traditional mine development methods have the tail wagging the dog, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 113-128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Wollongong* is Australia's largest single centre of mining and metallurgy. Wollongong's total employment in manufacturing of basic metal products (over 26,500 in 1972/1973) was almost 50 per cent higher than that of Newcastle and double that of any other Australian city. Although the great bulk of this employment was in steelmaking, Wollongong's copper industry was also a significant employer. Wollongong's total employment in mining (4,900 in 1971) was second only to that of Newcastle among Australian mining centres. Although the bulk of Wollongong's mining is of coal, there is also considerable mining of blue metal, sand and clay. In all, over 40 per cent of Wollongong's work force is employed in mining and metallurgy. The great bulk of the other

Jan 1, 1976

THIS SYMPOSIUM ON AUSTRALIAN BEACH SANDS IS MOST TIMELY; WHEN WE ARE APPROACHING PEAK PRODUCTION FROM THESE RESOURCES AND WHEN PRICES ARE GOOD, BUT THE RESOURCES CAN BE SEEN TO BE COMING TO AN END IN THE LIFETIME OF OUR YOUNGER COLLEAGUES - 20 TO 25 YEARS AS WE HEARD FROM ROY TOWNER TODAY. THE SPREAD OF PAPERS HAS BEEN 15 PERCENT EACH ON GEOLOGY AND THE MINERAL RESOURCES, WITH 25 PERCENT ON LAND USE AND ENVIRONMENTAL PROBLEMS. I AM PLEASED TO SEE 20 PERCENT HAS BEEN ON TREATMENT PROCESSES AND 25 PERCENT HAS BEEN CONCERNED WITH DOWNSTREAM USES. I SUSPECT THESE RATIOS ARE DUE IN PART TO THE WAY PAPERS WERE CALLED FOR, BUT THEY ALSO SUMMARISE CLOSELY THE BALANCE OF INTERESTS IN THE INDUSTRY. NOTE AGAIN; 30% CONCERNED WITH SUSTAIN -ING RESOURCES, BUT 25% WATCHING LAND USE AND IMPOSING CONTROLS; 20 % IMPROVING THE PRESENT PROCESSING, AND A HEALTHY 25% WITH AN INTEREST" IN WHAT HAPPENS TO THE MINERAL CONCENTRATES. I SHALL RETURN TO THIS FOURTH POINT AT THE END OF MY REMARKS. THE POSSIBILITY OF ADDITIONAL HEAVY MINERAL SANDS IN NEW AREAS WAS HINTED AT BY M.S. SHEPHERD (EG TERTIARY SHORELINES OF THE MURRAY BASIN). OLD FOSSIL SHORELINES, WELL REMOVED FROM PRESENT SHORES ARE AN IMPORTANT MINERAL SOURCE IN CHINA AND IT WOULD HAVE BEEN INTERESTING TO HEAR FROM THE SEVERAL COMPANIES EXPLORING IN THE MURRAY BASIN. I ALSO NOTICED THAT WHILST OUR MONAZITE

Jan 1, 1986

By He F, Zhu D

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced Normally.

Jan 1, 1992

A schematic overview of the variables which interact to determine ore reserves precedes consideration, in this context, of some recent views on the concept of a 'production cycle'. Political and governmental action, for whatever motives, is a greater obstacle to future mineral supply than technical problems.

Jan 1, 1979

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

By Andersson PO

Boliden Mineral AB Boliden Mineral AB operates nine mines in Northern and Central Sweden, producing zinc, lead and silver concentrates and copper and gold. Seven of these mines use cut and fill (C&F) mining with a total production of 2 Mtonnes of ore per year.

Jan 1, 1998

After a short presentation of the Division of Mining at the Royal Insti- tute of Technology, Stockholm, Sweden, the author presents some of-the fill research carried out at the Division. Literature surveys and testing methods and equipment are described. The use of flocculants' in hydraulic filling has been tested both in laboratory and in mines and the results are very promi- sing. Finally compressibility investi- gations and some finite element calcu- lations are presented.

Jan 1, 1973

By Di Pasquale S, Osler GD

Mount Isa Mines Limited recently commiss ioned an 800 tph Heavy Medium Preconcentration Plant for lead/zinc/silver ores. The decision to build this plant was made in late 1979 based largely on investigations conducted in the Company's pilot plant on a variety of ore types including Hilton ores, between 1972 and 1978. The paper reviews the historical develop- ment of the pilot plant heavy medium circuit through this period and illustrates the extent to which this work impacted on the final design criteria. This review also includes a description of plant operation, manning levels, process equipment and metallurgical performance Achieved.

Jan 1, 1978

After four or so long years at university, where life revolves around lectures, assignments, and drinking coffee strong enough to keep you awake for five nights in a row to finish your thesis, preparing yourself for employment is not an ea

Jan 1, 1994

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

While international coal trading operations often involve relatively small contract quantities, delivered over short periods or even in single shipments, most coal is supplied under long term arrangements. In entering into these arrangements the customer needs to be assured that coal of suitable and consistent quality can be supplied for their duration in the volume required. A detailed knowledge of the mine and transport system is required and must be presented from the customer's perspective.

Jan 1, 1983