Search Documents

By Clark IH

Numerical modelling is an effective aid for the planning and design of underground coal mines. With funding from the National Energy Research Development and Demonstration Program, CSIRO Division of Geomechanics has produced a workstation environment which will allow the Australian Coal Mining Industry access to a wide range of numerical design models. The emphasis is on usability and simplicity and the long-term aim is that the techniques should be used routinely at the mine site, so that, in the future, design of a new underground mine will routinely involve modelling of each proposed layout.Each of the five numerical analysis programs, FESOFt, FLAC, MNLAY, FEBLK and UDEC has both strengths and weaknesses. Some analyses with each program demonstrate areas when; observed in situ behaviour in underground coal mines has been successfully modelled, and the results of site monitoring provide a basis for comparison with the predictions of numerical models.

Jan 1, 1991

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The efficient development and exploitation of an orebody relies on an understanding of the mineral characteristics of the deposit. This information is valuable throughout the mining cycle - during exploration, assessment, testing, design, operation and rehabilitation. Problems can arise at each stage if there is an inadequate appreciation of the mineralogy involved and its effects on the treatment process. Modern image analysis systems now permit a more quantitative understanding of the mineralogy of an ore to be gathered. Where previously the metallurgist had to rely on qualitative information to guide technical decisions, it is now possible to give numerical estimates to the compositional and textural properties which govern the mineral concentration processes. Ore samples can be characterised according to modal abundances, mineral grain size parameters and mineral associations, all of which affect the liberation and concentration of the values. The paper will discuss the application of quantitative process mineralogy by considering a number of case studies. These include: ore characterisation to assist in exploration, assessment and mine planning; modal analysis of complex mineral suites to assist in the evaluation of ores, the deportment of values between products and the recovery or loss of these values; liberation analysis for ore testing, plant optimisation and performance monitoring; and characterisation of tailing to guide estimates of leachability, stability and rehabilitation options.

Jan 1, 1998

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Whiteley M, Robinson T, Vernon B

The Western Australian gold industry has approximately 100 operating plants, mainly CIP/CIL. The nature of the State's rapidly expanding gold industry gave rise to concerns over management of the cyanide hazard, in that most plants are remote from major population centres, have a workforce with a high turn over and use highly saline process water. Approximately 4,500 workers in the industry have the potential to be exposed to cyanide in the course of their normal work.This paper outlines the risk management strategy developed by Government and industry to monitor atmospheric HCN gas in the work environment and the role of continuing education and training along with regular site inspections by Department of Mines Inspectors.

Jan 1, 1990

Modern off-highway trucks have evolved over 30 years from small 20 ton units to vehic- les with capacities of up to 170 tons. Diesel engines are used by all manufacturers while transmissions are either mechanical or electri- cal. Development over the years has kept pace with component availability from engine, trans- mission and tyre manufacturers.Computer simula- tion studies are recognised for purposes of vehicle evaluation and costing under various op- erating conditions. Several manufacturers are currently manufacturing or evaluating vehicles with capacities of up to 260 tons. This paper describes the essential facts associated with the operation of off-highway trucks of the rear dump type in the mining industry.

Jan 1, 1973

By J de Witte

When used in suitable ground conditions, rock bolts can have advantages over other permanent tunnel lining solutions. Permanent rock bolts offer flexibility in tunnelling profile and rapid rock bolt installation can enable time and cost savings. There are also disadvantages when considering the suitability of rock bolts for permanent support installations. These generally concern achieving the specified durability requirement over the specified design life. By investigating alternate approaches to rock bolt installation, quality assurance (QA), monitoring and design life it may be possible to alleviate some of these concerns.The design and construction benefits that can be realised through the use of rock bolts are primarily related to reducing project program time. This time reduction could be realised if rock bolts are considered as a permanent solution, with the installation being completed as a part of the primary excavation cycle. Any reduction of the program could allow direct and indirect cost savings and in the case of a major project, allow the revenue stream to be realised earlier.Currently ambiguity exists where the treatment of rock bolts as permanent support components is inconsistent with that of (often identical) ground anchors, as utilised in stabilising cut and cover structures. The ground support design process, implementation and testing are generally similar, though the acceptance of rock bolts as long-term support elements is treated differently to ground anchors in technical specifications.This paper discusses some of the benefits available through the use of rock bolts. It offers different solutions to the concerns surrounding durability, including alternate approaches to installation, Quality Assurance practices and monitoring solutions. The selection of an alternate design life is also investigated as another means of alleviating concerns around long-term durability. The paper will also provide an indication of savings that could be expected through the use of rock bolts as part of a long-term support system.

Mar 8, 2011

By A Innis, A Bye, B McCarthy, S Glover

Technology adoption in the mining industry has been steadily increasing over the past decade, driven by the need to improve operational efficiency, safety, sustainability, and profitability. As mining companies wish to implement solutions to improve mining safety and productivity, various technologies are being integrated into mining operations to enhance processes, reduce risks, and optimise resource utilisation. Adoption of new technologies such as autonomous trucks requires a strong focus on foundational operational technology (OT) and a systems-thinking approach. OT support is critical however, OT is traditionally not considered or integrated into standard maintenance activities. Consequently, sourcing and applying service support to OT systems in real-time has posed significant challenges to date. Neglecting the monitoring and upkeep of these operational technologies and equipment can lead to a host of adverse consequences. Operating instability becomes more prevalent, necessitating reactive measures, and the vulnerability to cybersecurity threats increases significantly. To address OT monitoring and maintenance challenges, a systems wide mindset and remote support discipline must be utilised. Remote operations support refers to real-time, 24/7 monitoring, control and support of site OT: network, production systems, maintenance systems, enterprise systems and mobile and fixed plant through a single interface remote from site. The presence of a disciplined team, grounded in a systems-oriented approach, is of the utmost importance to remote monitoring, given the intricate interdependencies of OT systems. The ability to understand the relationships among multiple systems, coupled with the capacity to distinguish between symptoms and root causes, assumes a pivotal role in operations. Through diligent monitoring and the astute understanding of system thresholds, remote operations support can actively identify and alleviate constraints, in turn, serving as the enabler for transformative advancements in technology output.

Sep 1, 2024

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

Blast furnace slags which fall into the quaternary system SiO2 - A1203 - MgO - CaO have latent hydraulic properties which depend on the degree of vitrification. When the oxides com- bine to form Calcium Silicate Hydrates and other products of hydration the bonds between elements are at a lower energy level than those which exist in the glassy state. Transition from the glassy state to the crystalline state is thermo- dynamically favoured and, in the context of this paper, such slags possess internal energy. Manufacture of Portland cement is respon- sible for about 3.6 per cent of total industrial energy consumption in Canada. Pyroprocessing accounts for about 83 per cent of this figure or 3 per cent of the total. The processing of blast furnace slag to a condition in which it can be used as a partial substitute for Portland cement requires no pyroprocessing and, on average, only about 11 per cent of the energy needed for Portland cement. In North America the benefits of slag as a cementitious materials have been obscured by other considerations, the most important being commercial strategy. This situation has under- gone radical change as a result of the rising cost of energy, and government pressures to conserve energy.

Jan 1, 1979

By P Hayes, D Fadhlurrahman

Molten slags, fluxes and salts play key roles in a wide range of the high temperature industrial process applications, including metals production, refining and recycling, metal manufacturing processes, electrochemical metal production cells, batteries, and efficient heat transfer media. Recognising the importance and significance of fundamental scientific knowledge of these systems, the International MOLTEN Conference series was established to provide a forum to bring together leading academic researchers and industrial engineers to present and discuss the latest scientific ideas and findings, and their application in their respective fields. This article presents an analysis of the research carried out in this field over time in terms of the number of journal articles, fields and slag systems studied and geographical origin of the research.

Jun 19, 2024

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

By A D. Campbell

The sublevel caving (SLC) mining method is becoming more widely adopted as an underground mining method as mines become deeper and target lower grade mineralisation. SLC has been successfully adopted in increasingly complex and wide-ranging conditions in the past 10–20 years, demonstrating the flexibility of the method. Various challenges encountered at SLC mines around the world have led to significant differences in operating practices, mine performance and mine productivity. Unfortunately, aspects related to productivity, operational performance and best practice are not widely published and remain with individual companies. Limited information is publicly available to compare operational performance of SLC mines in the various conditions where the mining method is now being applied. To overcome this shortcoming, a global review of SLC operations was undertaken over a three-year period as part of the Cave Mining 2040 research consortium. The purpose of the review was to document technical and operational practices, hazard management strategies and key benchmarking metrics at SLC mines around the world. A total of 21 mines spread over four continents and 17 different mining companies were included in the project. The main outcome of the project was a manual of operational and technical practices, benchmarking of key metrics and documentation of the current state-of-the-art for each aspect of SLC mining. This paper describes the main findings from the benchmark in terms of mine productivity, including mine development, production and mining costs. The implications of mine scale, depth and ground conditions on operational performance at each of the benchmarked mines is described and charts are provided comparing key productivity metrics.

Mar 29, 2023

Segregation of granular material is a very common phenomenon. Realised in a forced manner it is a basis of all separation processes in mineral processing, mainly classification and beneficiation. Spontaneous segregation, occurring under dynamic conditions and making possible mutual translocations of grains, is however an undesired phenomenon as a rule. It decreases the degree of blending of the material which in many cases is an important technological feature of the material. It should be noted that the segregation can be treated as the reverse phenomenon to blending. The importance and frequency of spontaneous segregation has caused many rules and technical solutions to be developed aimed at decreasing the possibility of the spontaneous segregation. However, not enough attention has been focused on an quantitative description of the phenomenon of segregation, either to ways of quantitatively evaluating segregation effects or to explanation of the influence of conditions under which the grained material exists on the occurrence of segregation and its degree. The paper presents the following topics: 1. new numerical indicator for evaluation of the segregation degree (and blending) of material contained in an arbitrary determined region is proposed; it is determined relative to the maximum possible degree of segregation of the given material when taking into account its individual properties; values of the indicator can be calculated effectively for an arbitrary material, also for ulticomponent material. 2. there is proposed a way of evaluating the state of segregation (or blending) of material in an arbitrary part of the region mentioned above, based on investigation of the gradient of distribution of the material features; algorithms of analytical procedures and calculations are presented for typical cases met in mineral processing; 3. results of initial experimental studies, both laboratory and industrial, concerning the effect of the chosen factors occurring in transport and storage of the material on its degree of segregation are presented; and 4. conclusions referring to the fundamental and practical significance of the results are also presented.

Jan 1, 1993

By M Hilden, G Forbes, Z Ye, M Yahyaei, F Reyes, V Jokovic

Soft sensors offer several practical advantages for the process control of comminution circuits by combining multiple conventional sensors and other data sources with real-time analysis using mechanistic, phenomenological or machine learning models. While there has been a growth in the use of machine learning techniques for developing soft sensors in minerals processing applications, this paper describes advantages and challenges of using soft sensor models developed on the basis of process knowledge. Recent experience with three new soft sensor technologies developed by the authors are discussed. The Mill Filling Inference Tool which has been implemented at several mine sites, compares SAG mill load cell and power draw measurements with outputs of a semi-mechanistic power model to estimate the mill ball and total filling in real time. The progressive wear of the mill liners is modelled, allowing the model to correct the load mass due to the mass loss automatically and to estimate the charge trajectory. This information enables the mill to be operated more confidently near its limits. A coarse-ore stockpile soft sensor as been recently developed using a 3D cellular automata-based model to track ore size throughout the pile, and estimating the live capacity and size at each stockpile feeder to the primary mills. Finally, a hydrocyclone soft sensor is being developed to monitor performance using available hydrocyclone models to estimate the size and flow balance around the cyclone in real time. The model-based soft-sensor approach aims to synthesise and analyse existing data and provide operators and engineers with process- and model-relevant information that can facilitate making better process decisions. Maintenance data has proven useful for model development as it allows soft sensors to automatically adjust and compensate for the effect of progressive wear, for example for mill liners, thus helping the models to maintain calibration throughout the equipment life.

Aug 24, 2022

By W Y. Guo, L X. Chen, D X. Zhang

To obtain the rock type-I crack propagation process accurately, a novel fixture is used to make the prefabricated crack of rock propagation along the predetermined direction. In this study, the crack propagation process of rock is monitored with the digital image correlation method (DICM), and a mechanical model of crack directional propagation was established. The results show that the simple crack directional propagation device can effectively realise the stable propagation of type-I crack along the predetermined direction, the crack initiation angle is less than 10°, and the deviation between the peak strength of crack propagation calculated by a simplified mechanical model and the tensile strength of Brazilian splitting is 22.76 per cent and 7.53 per cent, respectively. According to the deformation field evolution law, crack propagation can be divided into three stages: microcrack development, main crack propagation, and main crack propagation. As for the rock type-I crack initiation and propagation mechanism, before reaching the peak strength, the prefabricated crack tip is subjected to maximum tensile stress; the elastic energy increases rapidly, and the dissipation energy increases slowly; after the peak strength, elastic energy exceeds its energy storage limit and released rapidly, and most of the input energy is converted into dissipation energy, which makes the crack propagation rapidly. The crack directional propagation device will be further optimised and improved, and it is expected to provide a new method for the study of crack propagation mechanism, rock failure precursor information and crack arrest principle, etc. It will also provide theoretical references for the optimisation of coal strata directional blasting, fracturing, fracture arrest, and other related technologies in geotechnical engineering.

Nov 29, 2022

By A H. Hofstra, G P. Landis, P Emsbo, A G. Hunt

Models of the evolution of the hydrothermal systems that form porphyry Cu (Mo-Au) deposits are compromised because aqueous magma-derived fluids in the ore zones of most deposits have changed from their original magmatic compositions as a result of cooling, depressurising, mineral precipitation, brine-vapour unmixing and fluid-rock reactions. However, in deep quartz-rich, sulfide-poor veins from numerous porphyry type deposits, we have identified parental fluids trapped in inclusions at near magmatic temperatures and pressures above the brine-vapour unmixing solvus. We have analysed these inclusions for bulk salinity, density, solute chemistry, helium isotopic ratios and elemental composition. These parental inclusions contain 35 - 70 volume per cent bubble, are low to moderate salinity, contain up to ten mol per cent CO2, and commonly contain a chalcopyrite daughter crystal. Our results indicate that these Cu-rich fluids transport Cu from a plutonic complex below upward into a hydrothermal system, where decompression, cooling, unmixing and water-rock reaction drive ore-mineral precipitation. Na/Cl ratios greater than one indicate that in addition to chlorine, sulfur and/or carbonate must play a key role in Cu transportation. Helium isotope ratios indicate that between ~15 and 100 per cent of helium in these fluids is mantle-derived. We suggest that in addition to He, volatiles from mafic magmas in the mantle are also likely to supply CO2, Cu and S to the fluids that form porphyry copper deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008