Search Documents

By J G. McLellan, B Miller

Copper and Gold mineralisation at the Ernest Henry deposit is bound by two controlling shears along the hanging wall and footwall margins. The shear zone geometries have been influenced by a large diorite intrusion, dated at ca. 1660 Ma, which lies to the north-east and south-west of the main orebody. The shear zones, which partitioned strain prior to the main mineralising event ca. 1514–1504 Ma, and in conjunction with adjacent regional structures, have been a critical factor in the deposit location and geometry. Conventional exploration techniques have been utilised proximal to the current deposit since the initial discovery in order to expand upon known resources, with limited success. However, new geomechanical modelling techniques have now been employed to target structurally controlled mineralised zones in three dimensions. The main aim of the geomechanical modelling was to simulate the effects of regional deformation events to highlight areas of anomalous strain, which indicate areas with a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE-SW compression) to examine preconditioning of the system, and a D4 event (SE-NW compression) which have ultimately been responsible for the current location of the mineralisation.CITATION:McLellan, J G and Miller, B, 2017. Geomechanical modelling of the Ernest Henry iron oxide copper gold deposit – identifying fluid pathways to predict potential mineralised zones, in Proceedings Tenth International Mining Geology Conference 2017, pp 75–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

It is a facet of modern-day life that change, even of a revolu- tionary nature, normally passes without comment. People have become so conditioned to continuous improve- ments in every aspect of their lives that they would be surprised only if there were to be no change. This paper seeks to demonstrate the extent of technical change, and to indicate the need for a fuller advantage to be taken of the technologies available, or potentially available, to the profes- sion. It contends that the mineral industry has been particularly slow to embrace technical change, and has good reason to con- sider an improved attitude for both prosperity and survival.

Jan 1, 1988

By F Kock, Y Sulianto, T Trott, B G. Putland, D Morgan

"Northparkes installed and commissioned a secondary crushing circuit in 2010 to debottleneck the semi-autogenous grinding (SAG) mill constrained grinding circuits. Following further improvements to the circuit (inclusion of a double deck vibrating screen), the project successfully delivered finer feed to the SAG mill. The result of this project was an increase in the milled tonnes from 5.6 Mt/a in 2012 to 6.0 Mt/a in 2013.The increased throughput rates introduced new challenges with the circuit becoming power limited. How to best optimise the available comminution power, while delivering the optimal particle size to the flotation circuit was made the key optimisation objective. To achieve this objective, Northparkes initiated a project that included engaging comminution experts. Recommendations included changes to the SAG mill including mill lifter design, increased grinding media charge levels and reduced grinding media size with aim of producing a finer grind size.Northparkes implemented these recommendations along with some other changes to SAG discharge grates and the mill discharge vibrating screen. This achieved a substantial reduction in the flotation feed particle size distribution (approximately 20 microns) by utilising increased average SAG power utilisation, in turn resulting in a two per cent increase in copper recovery.With power utilisation now maximised, the next phase of optimisation has moved to the throughput-grind-recovery relationship and the cost benefit analysis of installing additional grinding power.Citation:Sulianto, Y, Trott, T, Morgan, D, Bell, T, Kock, F and Putland, B, 2016. Optimisation of Installed Mill Power Post-installation of Secondary Crushing Circuit at Northparkes Mines, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 331–338 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By K M. Watling, F M, G K. Parker

Surface enhanced Raman scattering (SERS) spectroscopy at surfaces under electrochemical control has been applied to elucidate the adsorption of thiol collectors. SERS spectroelectrochemical studies at coinage metal electrodes have been carried out on ethyl xanthate and three iso-xanthates, O-isopropyl-N-ethylthionocarbamate, 2-mercaptobenzothiazole, diisobutyl- dithiophosphinate and butylethoxycarbonylthioura. For each collector, adsorption occurs via charge transfer to form a metal-sulfur bond and, in situations for which the reversible potential of the formation of the bulk phase is known, at underpotentials.

Jan 1, 2005

Chlorination of organic matter by direct injection of chlorine gas or hypochlorite has been investigated metallurgically worldwide with little understanding of the basic chemistry of the passivation mechanisms in- volved. In this paper, chlorination of carbon is attributed to oxidation-reduc- tions, resulting in surface halogenation of graphitic or amorphous carbon. It is proposed that chlorine and carbon interact to form thin coatings of chioro-carbon complexes that block the adsorption of gold cyanide com- plexes, thus passivating the gold adsorption sites of carbonaceous matter. Analytical, spectrographic, microscopic and electron-optical methods have been applied to demonstrate the proposed mechanism of chlorine-carbon bonding, as well as to evaluate the advantages and limitations of chlorination in the pretreatment of refractory carbonaceous gold ores.

Jan 1, 1991

By A Manzoori, M T. Shadloo

This paper describes a CFD modelling study which was carried out to investigate possible improvements in the design of an alumina precipitator tank at the Jajarm plant of Iran Alumina Company. In particular, the tank has an impeller located very close to the tank bottom, such that it quickly becomes covered with settled solids after a shut-down of the agitator, making it difficult to restart. A CFD model was firstly set up in which the existing design was evaluated in terms of flow pattern, off-bottom suspension and distribution of solids, and power consumption. Further simulations were then carried out to test alternative designs, leading to a recommended design, which maintains good mixing, with the same power consumption and without the use of a low-clearance impeller.

Jan 1, 2006

By F Flitti, M Haest, O Dominguez, D Mittrup, G Hird

The automated geology interpretation (AGI) tool has been developed in BHP Billiton to automate stratigraphy logging of drill holes, using any available quantitative data sets. At present, AGI is set-up to utilise geochemistry and mineralogy from infrared spectroscopic data to predict stratigraphy. Once the AGI tool is calibrated, results show that the tool is capable of automatically defining stratigraphy across all of the deposit types, encountered by BHP Billiton Iron Ore in the north-west of Western Australia. Accuracy of AGI at predicting stratigraphy is on average better than 75 per cent, with average accuracies exceeding 85 per cent for some deposit types. The AGI tool can deliver fast, accurate, consistent and objective geological interpretations.AGI is currently being implemented in BHP Billiton Iron Ore Exploration to streamline the drill hole logging process and allow geologists to spend less time defining stratigraphy at the drill hole level and more time investigating stratigraphy in 3D. This will deliver improved geology models, with significant downstream benefits in terms of better resource models, more accurate mine plans, higher plant efficiencies and more consistent ore products, driving productivity in BHP Billiton Iron Ore over the next decade.CITATION:Mittrup, D, Flitti, F, Hird, G, Haest, M and Dominguez, O, 2015. Semi-automated geological interpretation using assay and infrared spectroscopic sensing parameters towards improvements in geological modelling, in Proceedings Iron Ore 2015, pp 313–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

ALTHOUGH the development of the various flotation processes during the last 8 years has been so revolutionary, this development has been, until recently, entirely confined to the separation of the gangue from the mixed metalliferous sulphides.The desirability of finding some method of separating the independent sulphides from such a miXture, by means of flotation, has long been recognized. ThIS need was emphasized when the slimes resulting from the grinding of Broken Hill sulphide ores were for the first time successfully dealt with by the Mineral Separation Company's process on the Central mine. This process proved the practicability of separating the sulphides of lead and zinc as a mixed concentrate from the gangue present in slime. Although this was a very notable achievement, the process has not been generally used, owing to the mixed lead and zinc concentrates resulting from the treatment being acceptable neither to the zinc nor the lead smelters.Although the introduction of eucalyptus oil in minute quantities as an emulsifying agent has simplified the work of the subsequent tabling of mixed sulphide concentrates, rendering unnecessary the burning off or removal of the oil, there will always be a considerable quantity of slimy product too fine to settle on the moving surface of the concentrating machines, and therefore requiring other means for its division into lead and zinc concentrates.

Jan 1, 1911

The Broken Hill (BH) Block contains a wide variety of mineralization, with comrodities including Pb, Ag, Zn, W, Cu, Co and Sn. Much of the mineralization is stratigraphically controlled. Fe, Cu and Co-rich mineralization is dcminant in the Thackaringa Group; Pb, Ag, Zn and W is dcminant in the BH Group and Sn mineralization is present above the BH Group. Some mineralization occurs as concordant syngenetic deposits, but other types have been partly or completely remobilized by metamorphism, magmatic activity or hydrothermal fluids. Almost all of the non-syngenetic mineralization, including stratabound, vein and intrusive-related types, has formed from the "recycling" (remobilization and redeposition) of metals originally deposited with the sediments and volcanics of the Willyama Supergroup.

Jan 1, 1983

By Wang J, Ma Y, Jia H

The Hedong Gold Mine is located in the Yan(ai area, tihandong hroo%ill, e. China. It is an underground mine with an annual gold output of some 700 0(H) grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called 'sublevel open and fill stoping method' in the mine. Experience to-date is that new mining method is Satisfactory.

Jan 1, 1998

By G R Ryan

Recent events have raised the issue of whether, and if so when and how, an explorer may gather data from a mining tenement or permit which is held under the relevant mining Act by another party. Two situations arise: that of the small operator who wishes to prospect, and if successful mark off, ground held by others by virtue of the local form of exploration permit; and that of a regional explorer who may wish to enter on to some one else's existing mining tenement within the region of interest. The legal situation varies from state to state. At present the broad consensus seems to be that, provided consent is given, small-scale prospecting on another's exploration permit is at least tolerated if not actually provided for by the relevant Act. Entry onto a granted tenement to carry out any form of exploration is, however, prohibited in all jurisdictions unless consent is given. Furthermore it would appear that the proposal and conclusion of a joint venture agreement places certain obligations upon the party proposing to carry out exploration. These conclusions apply where ground surveys are proposed. Where data acquisition is by aerial survey the situation is much less clear, principally it would appear, because up to now little thought has been given to it. If trespass applies at ground level, at what height does it cease to apply? Can aerial magnetometry or photography be classified as prospecting? Is there an obligation upon public authorities who carry out remote sensing to make data available to the holders of mining tenements within the surveyed areas? Moves are now afoot to address these and other considerations, and it would be in the interests of everyone if a national approach to the problem could be adopted from the beginning. Certain suggestions in this respect are put forward.

Jan 1, 1994

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By E Widzyk-Capehart

The mines of the future can be envisioned as complex, large-scale technological systems being operated remotely from few centrally located (major cities) operating centres and skeletal crew stationed at the site. These systems will require remotely located human operators to constantly adapt to new and unforeseen system and environmental demands. In addition, the remote operators will need to match system properties to the changing demands and operational conditions, ie must be able to handle the ‘non-design’ emergencies, because the system designers would not have been able to foresee all possible scenarios of failures and provide automatic safety devices for every contingency. Therefore, it is highly important that the operators’ job, which involves problem solving and decision making at the workstation level, is facilitated by the proper interface designs. This paper argues that decision support systems and thus human-system interfaces for the mines of the future should be developed based on the principles of human-system integration that take into account human information processing and cognitive abilities. The information presented to the operator must support the operator in taking appropriate action through a human-system interface designed according to scientific principles of User Centred Design. A case study is presented where an iterative design process was used by CSIRO researchers as an evaluation method involving users (control room operators) at several stages of the user interface design in order to correct any design inadequacies as they emerged. This process allowed the designers to identify any usability issues before the user interface was fully implemented, which subsequently enabled the control room operators to easily adapt to the new interface and carry out all designated tasks in a timely and effective manner.

Nov 22, 2011

By J T. Woodcock

This paper discusses characterisation techniques that can be applied to complex waste products from metal production and processing operations with the aim of devising treatment methods for upgrading the metal content for recycling. Two waste streams were selected to illustrate the role of characterisation in adapting mineral processing techniques to provide an effective recycling strategy. Waste products chosen were:aluminium dross, which contains metallic aluminium particles in a coarse matrix of many components; and steel shredder sludge that contains copper wire and other metallics in a matrix of plastic and natural fibres, iron oxides, metallic iron, and other compounds. Characterisation methods discussed include chemical analysis (XRF, ICP-AES, and selected specialised techniques), phase analysis (XRD, SEM, TEM, and optical microscopy), morphology (IFESEM), sizing analysis (screening, Cyclosizing, Infrasizing, Malvern sizing), and general techniques such as particle shape, surface area, and porosity determinations. The applicability of these techniques to the waste products is considered in relation to their advantages and disadvantages, and sampling issues.Treatment techniques considered for the two waste products included comminution, screening, air or water classification, simple water leaching, gravity separation, magnetic separation, flotation, and eddy current separation.Tentative flow sheets were developed for the two wastes. For aluminium dross, it was proposed to use fine crushing followed by water washing to remove soluble chlorides and aluminium nitride, and then desliming followed by flotation of the granular fraction to give a metallic aluminium-rich concentrate. For shredder sludge, it was proposed to use wet screening, water classification, and gravity concentration to produce a copper-rich product and magnetic separation to produce a metallic iron-rich product.

Jan 1, 2004

By Morland R, Peck R

The Joint Committee of The Australasian Institute of Mining and Metallurgy (AusIMM) and the Australian Mining Industry Council (AMIC) have published a Code for the Reporting of Identified Mineral Resources and Ore Reserves. The Code is the result of an initiative begun in 1971 to achieve industry self regulation of Resources and Ore Reserves reporting which resulted first in guidelines for reporting standards but which have now been incorporated in ASX Listing Rules as a Code with significant sanctions ensuring compliance. This paper describes the background to the Code, its key provisions, and comments on practical aspects of working with the Code and compliance issues.

Jan 1, 1990

By J Zhang, B Wei, T Zhao, K Wang

Understanding mining-induced surface movement and fissures is critical for environmental protection and geological prevention. In this study, image recognition algorithms, satellite remote sensing and unmanned aerial vehicle photogrammetry (UAVP) were combined to identify surface movement and fissures caused by mining, and a case study was conducted in a coalmine in western China, and the following conclusions were obtained.

Sep 1, 2024

By Goldie R

The use of options theory in business has become well established in recent years and is currently one of the most exciting areas of current finance research. The theory can be used to value levered firms, and streams of contingent payments. This technique also has very practical applications in the areas of capital investment analysis and the valuation of equities in the natural resource industry. The use of options theory has been well accepted and used for many years in the trading of commodity options and futures contracts, in banking and insurance and in other industries. It also can be used to value such diverse contingent claims problems as the income tax liabilities of the firm and share underwriting agreements.Its application to the more complex options, such as those present in the resource industry, is only now becoming known. This lag is, at least partially, due to the difficult mathematics involved in solving complex options problems. Another factor is the almost overwhelming abundance of uncertainties, such as grade, tons and other natural risks, which must be considered in the evaluation mining projects.

Jan 1, 1990

By M Saghaeian, V Sheikhzadeh, R Hejazi

Mining dilution is one of the most important factors affecting the economy of mining projects. Instead of quantifying dilution in mining studies, it is common to assume a general dilution such as 5 per cent for massive deposits. Dilution increases the operating costs in the plant by increasing the tonnage of material to be milled. It prolongs the mine life by reducing plant’s effective capacity. It also reduces the feed grade. In most cases, lower feed grade means lower plant recovery. Dilution also increases the cut-off grade, which in turn reduces the overall ore utilisation of a mine. In this study has been investigated applying pre-concentration by dry magnetic separation for decreasing of dilution impact on reserve estimation and open pit design in low-grade iron ore mine. Based on the preliminary open pit design and assumption 3 per cent as dilution factor, the mineable ore in life-of-mine (measured + indicated) has been estimated with Fe = 25 per cent, SiO2 = 49.7 per cent. Based on the experimental test work on the ore, by dry low intensity magnetic separation of dry HPGR product grinding circuit, it is possible to remove diluted waste material and liberated gangue before concentrate plant, so that around 34 per cent rejected and Fe grade increase from 25 per cent to 33 per cent and by weight recovery 66 per cent. The results of the test work showed that this methodology could decrease largely the impact of dilution in the feed to the plant. It also slightly effect on the reducing of dilution factor impact for open pit design and optimisation and leads to increase the mineable tonnage in the low-grade magnetite iron ore mine.

Aug 24, 2022

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

Research cruises dedicated to seafloor hydrothermal activity along the Kermadec arc first began with the Sonne-135 expedition in 1998. This was followed by the worldÆs first systematic survey for venting along an arc during the 1999 NZAPLUME I expedition. Since then, cruises dedicated to mapping plumes along the Kermadec arc include NZAPLUME II (2002), NZAPLUME III (2004) and ROVARK (2007). In addition, the manned submersible cruises SWEEP Vents (2004) and NZASRoF (2005) utilised the Shinaki 6500 and Pisces V, respectively, to sample in detail select hydrothermalsystems for mineralised samples, rocks and vent fluids. The ROVARK (2007) cruise was the first to deploy an autonomous underwater vehicle (ABE) along the arc which surveyed Brothers volcano at a far greater resolution than had been done previously by ships on the sea surface. While these expeditions have largely been led by GNS Science, together with its collaborators from National Oceanic and Atmospheric Administration, Pacific Marine Environmental Laboratory (NOAA/PMEL), significant contributions have been made by other groups from various nations, exemplifying the global interest in seafloor hydrothermal activity associated with intraoceanic arcs. This is an ASTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008