Search Documents

By Iley J. D

The production of zinc from low grade concentrates, particularly those high in iron, has a poor economic return due to a combination of higher concentrate transport costs, increased processing costs and an increased cost for disposal of iron residues. The production of iron-bearing residues from the electrolytic zinc process is also seen as undesirable for both cost and environmental reasons. This paper details the pilot plant testwork conducted at the Pasminco Research Centre in conjunction with Minproc for the production of zinc oxide fume from a high-iron zinc sulphide concentrate from Colquiri in Bolivia. The concentrate is derived from a tailings retreatment operation and has a high iron content (40 - 45 per cent Zn, 14 - 17 per cent Fe) due to the presence of marmatite. Pilot plant trials were conducted using the slag bath reactor at Pasminco Research Centre at rates up to 500 kg/h of pelletised zinc concentrate, using a natural gas/oxygen-enriched air lance. The fume produced averaged 76 per cent Zn at recoveries up to 96 per cent and was recovered in a baghouse after gas cooling. The iron was oxidised into a fayalitic slag that passed the TCLP test (toxicity characteristic leaching procedure) and the sulphur was oxidised to produce a high SO2 gas which would be suitable for sulphuric acid production. The process produces a zinc oxide fume that can replace calcine as a feed for electrolytic zinc plants. The iron reports to a stable slag for disposal, thus eliminating the need for its disposal as jarosite from the leach plant. Only a simple leaching operation on the fume is required as there is no zinc ferrite present.

Jan 1, 1993

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020

By N J Welham

A commercial enargite concentrate was mechanically milled in inert and oxidising atmospheres for 10 hours. No substantial effect was observed in either an inert atmosphere or in air other than a broadening and weakening of the diffraction peaks. Milling dry in oxygen or wet in air was dramatic with a significant reaction occurring which formed arsenolite, As2O3 and CuSO4.5H2O, both of which are readily soluble.A small amount of SO2 was also formed. Dissolution in acid left CuS as the major phase implying incomplete oxidation. The small fraction of tennantite in the sample was comparatively resistant to oxidation.

Jan 1, 2001

By M Creech

During the 1990s, wider and more productive longwall panels were being introduced into the Newcastle Coalfield. The strata of the Newcastle Coalfield incorporate numerous massive sandstones and conglomerates, some of which formed the immediate roof of the coal seams being mined. The unexpected implications of introducing wider panels into this geological environment included more variable and increased subsidence, severe periodic weighting (with associated mid-face falls) as well as windblast.Subsidence prediction at the time was based on empirically derived data essentially relating subsidence to the width/depth ratio of the panel without accounting for actual widths, nor the impacts of variable geology. This approach required modification as locally derived data was gathered and reinterpreted.The interaction of massive strata located close to the roof of the mined seam resulted in dramatic implications for some of the operations. When associated with longwall goaf geomechanics severe periodic weighting events and crippling mid-face roof falls were the consequence. When associated with narrower panels and shortwall goaf geomechanics, mines in the region experienced aggressive windblast events. The relationships between the overlying massive strata, longwall panel geometry and the various risks encountered during this period is in the author’s opinion, the most concise still documented.As the extensive coalfields of Queensland turn to underground mining operations the relevance of these experiences cannot be underestimated. This paper will discuss recent developments as well as incorporating diverse subjects such as microseismic monitoring, low frequency radio emissions and ‘electrophonics’ as they relate also to the topic.Like Moriarty, massive strata can be disguised and can offend when you least expect. This paper documents a trail of crimes committed by conglomerate in the Newcastle Coalfield that were inflicted on the general public, miners and mining equipment. Although this paper concentrates on the criminal behaviour of conglomerate, this story is also relevant to other massive units such as coarse sandstones that may be more difficult to identify and apprehend. Currently Moriarty remains at large and able to reoffend at any time, once again taking advantage of the unwary.CITATION:Creech, M, 2014. Moriarty was a conglomerate – experiences and implications of coal mining under massive strata in the Newcastle Coalfield, in Proceedings Ninth International Mining Geology Conference 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Neville WE, Parkinson J

One of the earliest recorded risk management schemes was implemented by the boatmen of the Yangtze river some 4,000 years ago.. Between them they arranged for shipments to be split up in such a way that a load was divided five ways: if one was lost, then 80% of the shipment got through. Bottomry contracts were in vogue in Babylonian times with similar systems being used in India, in 60OBC and 4th century Greece. One of the first accepted mutual insurance ideas came in 1835 when a mill owner in America negotiated a lower insurance premium in return for installed fire safety measures. Approximately 20 years ago risk management as a philosophy was developed in the U.S.A., the philosophy followed to England and hence to Australia about 10 years ago. The business climate which induced the philosophy of risk management was that of "tight money". The definition of "assets" was then broadened to include earning capacity, skilled personnel and in a negative sense, a corporation's liabilities. In more affluent days losses were comfortably absorbed into the ongoing business expenses, the more prudent managers took out insurance which "covered everything" at a suitable premium. Statistics are available to indicate that a high percentage, (over 60%) of businesses which suffer massive plant damage due to fire, do not restart operations, or in the event of restarting have closed operations within the next 2 to 3 years - in spite of collecting an insurance payout.

Jan 1, 1986

By Reimer TH

The model described in this paper has been developed for and in close collaboration with the Bong Mining Company Ltd, Liberia/West Africa. When working an irregular deposit a de- tailed short term production schedule becomes necessary in order to ensure an equal and homo- genous concentrator feed. If the irregularity of the ore body exceeds a certain degree, blen- ding facilities have to be provided between the mine and the concentrator, but even then sche- duling of the mine production is inevitable to meet the given requirements of the blending bed and to keep these conditions steady for at least some of the successive periods. To assist the planning department in set- ting up optimal production schedules a computer model has been developed using a linear pro- gramming approach. The deposit is divided into equally shaped blocks containing defined quali- ties and quantities of ore and/or waste; from which one has to select those quantities of ore which will meet the requirements of the blen- ding bed. The objective function of the model

Jan 1, 1977

Coal exploration and mine planning now use all the modem techniques to indicate geological hazards to a new or developing coal mine. Drilling, seismic and other sophisticated geophysical methods aim to increase the reliability of prediction of features which will inhibit mine development. But do they?. During the past 40 years, geological investigations for coal mines in New South Wales have ranged from the general observations of Eric Rudd, in the Southern Coalfield in the late 1940s to the very detailed examinations of roof strata by John Shepherd and others in the 1980s. Then, the large scale regional relationships between sedimentary and structural features often were ignored as the minute examination of seam roof strata became fashionable.

Jan 1, 1991

Classifications of Ni-Cu deposits are based on petrology, geochemistry and the geotectonic setting of host igneous bodies (Naldrett and Cabri, 1976; Besson et al, 1979; Nadrett, 1989). The four major classes in Naldrett's (1989) division rest on the geotectonic setting of the igneous complexes and the classes are further subdivided on the basis of the petrology and geochemistry of the intrusion. A more common subdivision of mafic and ultramafic igneous rocks is based on the environment of rock-forming processes, endogenic or exogenic, intrusive or extrusive, and this subdivision has been applied, in practice, to the classification of sulphide Ni-Cu deposits, too. The extrusive deposits, Class I in Naldrett's (1989) classification, are directly related to volcanic processes whereas all the others refer to the intrusive environment. This paper looks at the differences between the extrusive and intrusive groups of Ni-Cu deposits and presents generic, genetic and structural features of the intrusive group.

Jan 1, 1996

By B N. Noller, J C. Ng, S L. Bruce

Mining activities can result in the transfer of harmful elements, including arsenic and lead, into the environment. In Australia, one of the potential future uses of rehabilitated mine land is to stock grazing animals. Elemental uptake is dependent on bioavailable fraction for adsorption upon exposure. Bioavailability data are generally lacking in order to provide realistic health risk assessments relating to harmful elements from mine tailings in Australian conditions. Another key component of risk assessment is the ability to estimate a realistic exposure, or dose rate, of the tailings to the grazing cattle over a set period of time. Hence, we aimed to conduct grazing trials directly on rehabilitated tailings facilities in order to provide valuable in situ information on heavy metal dose rates and associated accumulation. For the laboratory-based evaluation of comparative bioavailability, groups of cattle were fed five days a week on a normal diet spiked with mine tailings or soluble pure salts of target elements (eg sodium arsenate, sodium arsenite and lead acetate) for about eight months. For the field validation, cattle were allowed to graze directly on rehabilitated tailings facilities over a similar length of time. Blood and a biopsy of the muscle and liver were periodically collected to monitor arsenic accumulation. At necropsy, blood, muscle, liver, kidney and other saleable tissues were measured for arsenic concentrations. Although this study was focused on arsenic, lead and other metals were also measured. Predictive models for arsenic and other metals have been established to calculate the maximum grazing duration without the risk of exceeding specific food safety guidelines. The outcome of this study is a predictive model for maximum beneficial use of certain rehabilitated tailings for cattle grazing where grazing activities do not impact on the integrity of the tailings dams.CITATION:Ng, J C, Noller, B N and Bruce, S L, 2014. A predictive model for beneficial use of rehabilitated mine tailings for grazing cattle after mine closure, in Proceedings Life-of-Mine 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The Mount Lyell Company's concentrating mill is situated about a quarter of a mile westward of the portal of the North Lyell tunnel, which serves the North Lyell, Royal Tharsis and Crown Lyell mines, being on the 1100-ft. level of the first named. The Comstock mine is connected with the tram system at this level by five and a half miles of steam tramway, two-foot gauge being standard throughout.The plant is well placed with regard to all essential services and has an excellent water-supply from a series of three dams on the West Queen river.MILLING ORESThe mill feed is a mixture of the outputs from the foUr mines mentioned, each of which has its characteristic ore, but, generally speaking, about half of the ore consists of siliceous schists and the other half of hard grey quartzite. The schisty ores are easy to crush, but, on grinding, while the schist slimes readily, the quartz granules are hard, resulting in the handling of heavy loads on the secondary classifiers. The quartzite ores are both hard to crush and difficultto grind.The principal sulphide materials are bornite, chalcopyrite, and pyrite, chalcopyrite being the main copper-bearing mineral.The crystallization is coarse in the schisty ores, but it has been shown that even the 200 mesh (Tyler) material contains included sulphide particles. At the present time the sizing of the final tailing averages 80% through 200 mesh.

Jan 1, 1932

By Withington J. T

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

Integrated chemical thermodynamic software and computerised databank systems have evolved over the last 15 years. The extent to which these systems have automated thermodynamic calculations relevant to extractive metallurgy is examined. The scope for further automation and the role of the expert consultant is discussed.

Jan 1, 1991

By C S. Kelsey, J R. Kelly

Australia is presently enjoying the fruits of a booming iron ore market. Expectations are that market strength will be supported in the short to medium term by increasing feedstock demands from steel mills, as world economies rebuild post-Covid-19. However, as cost and environmental pressures increase the longer-term market outlook will be dominated by product quality. The ‘flight to quality’ will place increasing demands on direct shipping ore miners as they compete to maintain their standing in the iron ore marketplace. China will progressively disengage from its dependence on Australian imports, leaving miners under increasing pressure to boost product quality and diversify outlets globally. Australia has vast deposits of low-grade magnetite ores located mainly in remote and arid regions of the continent. This paper proposes a dry grinding and magnetic separation process to produce premium concentrate grades from the low-grade ores, to assist in meeting future product quality demands. The premium grade concentrates could be either blended with lower quality direct shipping ores or marketed separately. The proposed dry concentration process involves the pairing of Vertical Roller Milling (VRM), a mature technology widely used in the cement industry, and Planar Magnetic Separation (PMS), a new methodology, which has been developed to the threshold of commercialisation by the private Australian company Cyclomag P/L. Two laboratory prototype planar magnetic separators with field strengths of 1800 gauss and 6000 gauss have been built and tested on a range of magnetite ore types over the past three years. In each case, following grinding to liberation sizes, a combination of roughing and cleaning operations has produced pellet grade concentrates. Vertical roller milling has competed successfully with conventional media milling in grinding cement clinker, limestone and blast furnace slags. A key advantage of dry VRM/PMS processing is its potential adaptability to stepwise modular development, which can minimise initial capital investment, while generating early revenue streams to cope with unpredictable market volatility.

Nov 8, 2021

The reality is that in today's world almost half of nearly six billion people on the planet do not have access to commercial energy and the services it brings. Based on UN projections, in 30 years time there are likely to be nearly three billion more people in the world, over 90 per cent of them in countries which are already economically poor. The World Energy Council (WEC), through its 102 member countries, monitors trends and developments and projects future trends. WEC is a non-governmental international body representing all forms of energy and is committed to the sustainable use of energy for all mankind. This paper is based on WEC studies and papers presented at its many conferences and congresses worldwide. Primary energy demand growth is dominated by the developing countries over the next 30 years. The world energy mix is projected to change very little over the next 30 years. Fossil fuel supplies (ie coal, oil and gas) are likely to decline from 77 per cent to 73 per cent, nuclear energy may grow from five per cent to six per cent and renewable energy sources (eg hydro, solar, geothermal, wind, tidal and biomass) could increase from 18 per cent to 21 per cent. World energy consumption is expected to grow by over 50 per cent over the next 30 years. The paper reviews changes in energy demand in the world, particularly in the Asia/Pacific region. Environmental issues are covered, as are developments such as solar energy from space and the status of renewable energy forms. Agendas for action to achieve change are also reviewed.

Jan 1, 1997

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By L Cain, C Every, S Mirlatifi, J Ashley

This paper presents a geographic information system (GIS) based method for the prediction of ground movement and the associated impact on existing buildings and structures due to tunnelling in the North West Rail Link (NWRL) project. The NWRL is a priority rail infrastructure project for the New South Wales (NSW) Government and includes 15 km of twin tunnels between Bella Vista and Epping, which will be Australia’s longest rail tunnels. The NWRL tunnels will be constructed in an urban environment where the prediction of ground movements induced by tunnelling and the associated impacts to existing structures must be assessed in the early design stages of the project. An assessment process was developed using GIS able to respond to design changes.An iterative GIS analysis methodology was developed to generate ground settlement contours and identify impacted buildings and structures in response to multiple changes in tunnel alignment during design development stages. The GIS analysis undertook to rapidly provide detailed and accurate parameter information including tunnel depth from surface, tunnel separation, diameter and sample point proximity to the tunnel and assess ground movement contours along the project alignment. Determination of the ground surface settlements were based on empirical methods proposed by Peck (1969) and Mair (1993). The control parameters and the relationship between damage categories and risk classifications for impact assessment were based on Burland, Broms and de Mello (1977), Rankin (1988) and Boscardin and Cording (1989) methods.The GIS-based ground movement impact assessment approach adopted for the NWRL project demonstrates an efficient, iterative and robust approach and could provide an initial framework for other similar tunnelling projects where rapid design changes and early understanding of tunnelling impacts are required to bring greatest benefit to all stakeholders.CITATION:Mirlatifi, S, Cain, L, Ashley, J and Every, C, 2014. An iterative geographic information system based approach for the assessment of tunnelling impact to existing buildings and structures, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 647–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014