Search Documents

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

Efficient project planning during the detailed feasibility to final engineering stages of a project requires not only the accurate prediction of the grade, tonnes and recovery, but their degree of variability as well. An understanding of the major parameters involved in the grade and tonnage estimates is essential, and the communication to those receiving the results is most important. The personnel involved in the project require more than just a global reserves classification. Quality parameters other than grade should be evaluated as carefully as the estimate itself. This paper does not present any novel ideas to overcome or enhance any of this. Rather, it takes a step back and tries to look at the global picture of requirements for proper project planning.

Jan 1, 1987

By A Tawadrous, D S. Preece

Cave mining is of interest to the mining community as it offers a chance to extract large, deep orebodies with low operating costs and high production rates. It allows for extracting large low-grade orebodies, which may not have previously been considered for mining. Cave mining is done either top down (ie sublevel caving) or bottom up (ie block/panel caving). Both approaches rely on gravity, stresses and weakness of the rock to fracture and achieve a controlled collapse.Block caving starts at the base of the orebody. It progresses upward and across through continuous collapse of the roof. To achieve this, a critical hydraulic radius must be exceeded. This is accomplished by blasting drawbells, through which the caved ore passes to the production level. An entire level above the drawbells (undercut level) is excavated to help initiate the cave. The undercut level ensures the connection between drawbells and achievement of the required hydraulic radius.Conventionally, drawbells are generated by drilling and blasting several times from the production level as well as the undercut level. Mucking between each shot is required to generate enough void space for the rock to swell. The need for several blasts necessitates some downtime between each blast. Also, the cost of developing and maintaining the undercut level can constitute up to 35 per cent of the cost of mining the panel.A new blasting technique was developed to create the drawbells in a single blast from the production level. The technique ensures the connection of the drawbell to the neighbouring ones, thus, the critical hydraulic radius is reached and propagation of the cave achieved without the need for the undercut level. The technique has the potential to reduce the capital cost of a block caving operation, increase its feasibility and reduce time to reach the ore and consequently the payback period. This paper presents the modelling of a traditional drawbell excavation process, the philosophy of the developed technique, the modelling of that new design and its implementation.CITATION:Tawadrous, A and Preece, D S, 2015. A novel blasting technique to create drawbells and eliminate the undercut level in block cave mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 617–624 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The fundamental natural ingredient of any mining development is an ore reserve. The classical definition of an ore reserve has both technical and commercial components, each involving elements of risk. By definition the desposit must contain mineral values which are "extractable at a profit". Metallurgy supplies a vital link between these two basic requirements of a successful mining project; the metallurgical input establishes the process by which the contained minerals may be recovered and converted into marketable product(s).

Jan 1, 1983

The recommissioning of the plant at Mary Kathleen involved several distinct phases. The previous plant process was modified significantly, the plant capacity was increased by the addition of new equipment and the exist- ing equipment was in most cases overhauled. This equipment was either reused in its original duty or relocated. Maintenance requirements after the plant was cmommissioned were high because of the amount of modified equipment and also because some old items of equipment were deliberately not overhauled during recommissioning. The equipment that was overhauled has operated reliably. However some new equipment has not been as satisfactory.

Jan 1, 1978

By R C. Owen, M A. Ward

The paper describes the application of New Zealand's environmental impact assessment procedures to a proposed gold and silver mine in the North Island of New Zealand. The project is described and a summary is provided of the statutory permits or consents that are required prior to operation of the project. Emphasis is given to the requirement for environmental impact assessment and the preparation of a formal environmental impact report. The company's approach to impact assessment is described, with examples of how this assessment and the identification of management alternatives influenced the engineering design of the project. This paper was prepared as a contribution to a working session of the International Association of Impact Assessment VII Annual Conference, July 1988.

Jan 1, 1988

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By J Mauk, J Rowland

The Karangahake epithermal Au-Ag mine consists of two main lodes, the Maria and the Welcome/Crown hosted in Miocene andesites. Mineralisation is strongly constrained to major structures and is genetically linked to dynamic tectonic processes. Two main periods of faulting are represented in the deposit: 1. NE striking right-lateral/normal oblique linked spatially and temporally with the mineralising system, and 2. ESE striking right-lateral/normal oblique post-mineral faulting that displaces the lodes. Paleostress analyses performed on a limited kinematic data set indicate NW-SE extension during the formation of the vein system. Veins and lodes strike NNNE and accordingly contain a strike-slip component. The kinematics of vein formation at Karangahake is broadly consistent with that of other deposits within a NNE-trending belt of deposits. Oblique shear on deflecting structures will create zones of compression and dilation. Dilatant zones created on steep structures create fluid pathways potentially focussing large volumes of fluid from deep parts of the system into dynamic structures.

Jan 1, 2003

By M I. Pownceby, J Manuel, S Suthers, A Poliakov, E Donskoi, N Ware

"The mining industry is constantly seeking methods for optimising the exploitation of mineral resources, such as iron ore, in a sustainable and eco-efficient manner for economic and social benefit. When faced with resources that have mineralogical or textural complexity, poorer grades or geological variability, it is particularly important to apply a comprehensive geometallurgical approach to the development of the mining operation, from resource definition through to processed product. Integral to this approach is the quantitative characterisation of representative samples across the whole orebody.A key factor that associates the geological characteristics of iron ores to their processing response is ore texture. While the classification of samples on the basis of chemical or physical properties alone is often not sufficient to predict their processing behaviour, classification and quantification of texture types can be effectively correlated to metallurgical performance in processes such as blending, beneficiation, pellet making, sintering and ironmaking. This paper describes some of the research conducted by CSIRO pertaining to the design and rationale of a texture-based classification system for Australian iron ores; some of the tools developed and used to apply such classification; and the application of the generated data to quantifying, modelling and predicting sintering behaviour and performance in the blast furnace.CITATION:Suthers, S, Pownceby, M I, Manuel, J, Ware, N, Donskoi, E and Poliakov, A, 2016. Geometallurgical Characterisation of Australian Iron Ores – from Ore to Processed Product, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988

By D J. Williams, A Shokouhi, A Naderian

Extracting alumina from bauxite involves the production of fine-grained waste known as red mud. The highly alkaline red mud is usually neutralised by applying sea water, thickened to between 25% and 30% solids by mass, before disposal to a Tailing Storage Facility (TSF). Hydraulic sorting, settling, self-weight consolidation, and desiccation are the processes contributing to the overall volume change of the red mud after deposition. Investigating the effect of these processes on the volume change behaviour of the fine-grained red mud is an important step in the estimation of the required storage volume of the storage facilities. This paper presents the results of a series of laboratory consolidation tests in a slurry consolidometer, and comparisons are made with field testing and observations.CITATION:Shokouhi, A, Naderian, A and Williams, D J, 2018. Assessing the volume change behaviour of red mud through laboratory and field testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 309–316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G D. McDonald

Flinders Mines is an ASX300 iron ore explorer and developer with a tenement package located in the Hamersley Ranges region of Western Australia, approximately 70 km north of Tom Price. Exploration over the past three years has identified a Global Resource in excess of 740 Mt at a grade of 55.4 per cent Fe (+50 per cent Fe cut-off). This resource is spread across multiple deposits and has been divided into a number of mineralisation type domains based on geometallurgical and geochemical boundaries. These domains are comprised of transported haematite rich detrital iron deposits (DID) and goethite dominant Channel iron deposits (CID) as well as in situ bedded Brockman iron deposits (BID). On the basis of differences in physical and chemical characteristics, the DID have been divided into four discrete units. The four DID units form a stratigraphic sequence with the iron grade increasing and the contaminant concentrations decreasing with depth. The upper DID unit is lower grade and currently unlikely to provide a marketable product, without signifi cant beneficiation. The lower three DID units, together with the CID and BID, are of a higher quality and have the potential to yield marketable ore. The ability to define and recognise these different units has resulted in a more reliable and robust geological interpretation and hence greater confidence in the resulting resource model. This has been evident in the excellent conversion of inferred to indicated resources.

Jul 11, 2011

By C Gimber

Dust suppression is an important environmental control in most mining operations. The poorest quality water within a mine site is often used for dust suppression since it provides an effective means of reducing the volume of poor quality water. The ultimate fate of contaminants or salinity associated with water used in dust suppression is important to consider for optimising water management and assessing the environmental impact and life span and maintenance requirements of roads associated with dust suppression.The propensity for remobilisation of contaminants or salts depends on a range of factors such as the application rate, climate, road construction, water chemistry and soil geochemistry. This paper describes a typical study approach which could be used to assess the short- and long-term impacts of mine water application for dust suppression. The steps of the study are: reviewing the environmental setting, estimating water requirements for dust suppression, reviewing source water chemistry, developing a mass balance model and assessing the mobility and fate of contaminants with a geochemical model.This approach identifies which salt species are likely to form and whether they are prone to remobilisation. It is possible to quantitatively assess the risk of exporting contaminants or salt from roads and to refine the dust suppression strategy to minimise the environmental risk. The approach can be applied at mine sites to address regulator concerns, aid decision-making and improve the understanding of short- and long-term environmental risks.CITATION:Gimber, C, 2013. Assessing contaminant risk associated with the use of mine water for dust suppression, in Proceedings Water in Mining 2013 , pp 235-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Oxidation or sulphidization of the surface of pyrrhotIte partIcles enhances atomic interdiffusion at elevated temperatures and provides a mechanism for interface growth between particles in contact. In a mass of pyrrhotite-rich ore or tailing, where oxidation heating is not controlled, bonding of particles by diffusional mass transport contributes significantly to the agglomeration of the mass.

Jan 1, 1976

Carbonatites - igneous carbonate-silicate rocks - host the world's major resources for niobium, phosphorous and REE (rare earth elements).Carbonatites represent the least common products of mantle and igneous processes and their emplacement is principally controlled by lithospheric domes and rift structures. Intrusive carbonatites frequently comprise carbonate-amphibole-apatite-pyrocWore assemblages, occur as plugs, cores, dykes, sills sheets, veins, pipes and irregular bodies, are gecichemically anomalous (Ba, Ca, Cl, F, Hf, Mg, Nb, P, REE, S, Sc, SO4, Sri Tb, Ti, D, V, Zr), are associated with alkaline silica-undersaturated igneous rocks forming carbonatite complexes, and display large, intensive alteration haloes. Also carbonatites are similar to limestones, prone to weathering, and may form thick laterite profiles.Magmatic ores (pyrocWore, apatite, bastnaesite, monazite, magnetite, baddeleyite, phlogopite, fluorite, calcite) and weathering related residual and supergene ores (pyrochlore, apatite, magnetite, anatase, vermiculite) are currently being mined on all continents except Australia. Australia is underexplored for carbonatite associated primary magmatic and especially residual-supergene ore deposits. Chances are very high for the finding of new carbonatite, occurrences and associated ores.

Jan 1, 1994

Mining is a global industry. The conference is a good example of this, as itÆs jointly organised by professional associations from Canada, Australia and South Africa, and has attracted speakers and delegates from around the world. I commend the organisers for their initiative. I am pleased to be asked to participate in this panel û although I would hasten to add I see myself as perhaps an informed observer rather than an expert. It wonÆt be news to most in this room that AustraliaÆs mining sector is booming. As one of the most productive and diversified mineral regions in the world, this activity is also something that has not escaped the attention of CanadaÆs largest mining companies! This means that I follow what is happening in the industry and more specifically what might be occurring here. Two-way investment between Canada and Australia stood at $9.8 billion in 2005 with Canada as the seventh largest overall investor in Australia with $8.22 billion in investments. The majority of this investment is by Canadian minerals and metals companies. In recognition of the importance of Canadian investment in this sector in Australia, I maintain close contact with our companies. By way of example, in the past two months I spent a week in Western Australia visiting Perth and meeting with companies for example, like Teck Cominco and LionOre as well as seeing various Barrick Gold operations in Kalgoorlie. I attended the opening of AlcanÆs new Asia Pacific Headquarters in Brisbane in August and just two weeks ago was in Cowal, NSW for the opening of BarrickÆs new mine there. Having met with BHP Billiton in Vancouver, IÆm equally aware of active Australian mining interests in Canada. This is not designed to indicate how active I am but rather to demonstrate the dynamism in the mining industry and the diversity of Canadian mining interests in this country and Australian interests in Canada.

Jan 1, 2006

In the last 40 years, New Zealand has developed a number of liquid- dominated geothermal steam fields, for electricity generation and indus- trial process steam. New technologies were developed, and in this work, New Zealand led the world. The policy of full publication of the results, in a wide range of sciences, provided a reservoir of detailed data defin- ing the geology, size and shape, and the chemical and physical regime, of many geothermal fields and their constituent parts. The discovery of precious and base metal deposits /precipitates in geothermal drill cores and steamfield equipment, suggested a clear link- age with epithermal mineral fields in general, and with that of the Coromandel (Hauraki) Region in particular. Further work on geothermal/ epithermal relationships have implied that the techniques, developed to obtain an understanding of geothermal fields, could be applied also to epithermal mineral exploration. This work is developing fast, and is now proceeding in many coun- tries. Future work may show that the presumed relationship between geothermal and epithermal deposits may be applicable in the wider con- texts of all hydrothermal deposits, and possibly in many other minera- lised areas with volcanic "country rocks".

Jan 1, 1988

By J Levett, O Rondon, I Glacken

Reporting Codes are not prescriptive on methodologies to report or classify Mineral Resource Estimation results, but the assessment of risk and uncertainty is required, and is likely to be increasingly important in future Code updates. The 2012 JORC Code indicates that relative confidence in tonnage-grade estimations should be considered for classification, and that there should be a discussion of relative accuracy and confidence levels in the Mineral Resource Estimate. These considerations are also relevant to the drill hole spacing required for various classification categories, along with other geological and data quality criteria. This paper summarises the theory, principles and current practice of various drill hole spacing analysis techniques for both achieving a desired level of resource categorisation and for optimising grade control or resource drill-out costs. The authors provide practitioners with a guide in their use to assess uncertainty and relative accuracy, as illustrated by a number of case studies. While all drill hole spacing studies rely on the assumption of consistency of the continuity model from current to future drilling, the range of methods available provide much more objective outcomes than previously adopted ‘rules-of-thumb’.

May 24, 2023