Search Documents

The nature of exploration in Australia is reviewed from its inception to the present time. It is seen as consisting of three phases: the first, prospecting; the second and third, mainly company-based activity. The first yielded the discoveries on which the mining industry was originally built. The great recent growth of the industry has been due mainly to the discoveries of the third. The technical, organisational, legis- lative and other aspects are reviewed. The overall result has been a very great increase in the known mineral resources and, viewed collectively, exploration is seen as providing the principal means of assessing, evaluating and building up the nation's mineral resources.

Jan 1, 1973

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

As the mining sector increasingly embraces the sustainability agenda, and implements thorough environmental reporting in support of its case for a continued æsocial licence to operateÆ, there is a need for ever-clearer metrics for key areas of impact. It is clear that natural waters are both the predominant pathway and main recipient of the environmental impacts of mining. A new approach to summarising the impacts of mining operations on water quantity and quality is proposed, adapted from an existing generic framework, which is increasingly used to quantify the æwater footprintsÆ of cities and nations. This includes both direct water use and ævirtual waterÆ use, implicit in goods and services used by the mine. In contrast to the existing formulation of æwater footprintÆ, it is here argued that it makes hydrological sense to express the water footprints of mines in areal terms, as equivalent catchment areas. It is also important in the mining sector to capture systematic changes in the scale of impact, which can be anticipated and predictively quantified over the full life cycle. This includes the essentially infinite post-closure phase, during which æremanent water consumptionÆ occurs, either through physical water loss (eg by evaporation from pit lakes) or by ongoing contamination of sizeable flows of natural waters. Methods for assessing the water footprints of mines are now available, and the time is increasingly ripe for them to be applied in earnest in environmental reporting. An example application to a mine in a humid subtropical area of South America is presented. In that case, the mine site itself extended over 106 ha, whereas the maximum water footprint exceeded this by a factor of 27. Although the water footprint can be expected to decline by a factor of ten immediately after closure, sustained evaporation from pit lakes and tailings dams with water covers will gradually increase the remanent water consumption rate, such that the final post-closure water footprint remains about 25 per cent of that encountered during the peak of mining.

Jan 1, 2006

Choosing an Effective Dust Suppressant

Sep 13, 2010

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

The geological features of the destructive plate margins of the southwest Pacific favour the formation of porphyry type deposits. The major controlling factor favouring the formation of gold-rich deposits of this type is a dense crust. This results in shallow intrusion of large magma bodies beneath andesite stratovolcanoes. Where the intrusives have near vertical sides, the comparatively low temperature of transfer of volatiles from the solidifying melt favours the partitioning of gold into bubbles of volatiles. They reduce the viscosity and density of the melt, resulting in the upward movement of a mineralised melt. With the drop of pressure with upward movement the bubbles separate into a two phase mixture, triggering freezing of the mineralised melt and the formation of a gold mineralised stockwork.

Jan 1, 1995

Applications of chlorine metallurgy to the extraction of metals often result in the production of volatile metallic chlorides, most of which condense directly to a solid phase at 1 atm pressure. A stirred-bed condenser suitable for the recovery of these materials is described.The unit, developed from the concept of a fluid bed condenser, has the advantages of versatility of operation and ability to control fog and dust formation. Test work using aluminium chloride vapour (as an example of a volatile chloride) gave recoveries approaching 100 per cent. The yield was dependent upon halide content of the vapour, flowrate, and, to a lesser extent, upon coolant temperature. Analysis of the heat transfer dataindicated condensation side coefficients in the range 10 to 30 B.T.U./hr sq. ft. 0p.

Jan 1, 1971

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By F Musa

One of the main energy efficiency opportunities identified from the majority of mine site energy audits is to optimize the comminution circuit to reduce energy consumption through improved throughput and product size distribution. Typical analysis reviews comminution process efficiency/inefficiency i.e. utilization of grinding mills, process bottlenecks and product vs. target size, to identify instances of overgrinding or undergrinding. From this, it is possible to establish the potential improvement that could be gained through formal plant optimization and what the optimization program would entail. It can also sometimes reveal immediate opportunities for process improvement. This paper presents steps that can be taken to optimize the efficiency of comminution circuits.

Aug 8, 2011

By C Delwig

ThyssenKrupp specialises in the manufacture of high-grade steel-sheet products. Its main customers include the automotive, construction, household appliance, energy and packaging industries.At its works in Duisburg, Germany, ThyssenKrupp Steel Europe produces 12 Mt of crude steel annually, making Duisburg one of the world’s largest steel hubs.ThyssenKrupp have installed an online elemental analyser and limestone dosing control System on one of three Sinter strands at Duisburg in an attempt to control the sinter raw mix with better precision. Traditionally, set point changes to the raw mixture were made after sampling and laboratory analysis of the sinter product. The analyser chosen uses prompt gamma neutron activation analysis to determine the elemental content of moving material on a conveyor each minute and was supplied by Thermo Fisher Scientific. The project goal was to control the CaO/SiO2 ratio (basicity) and reduce its variability in the sinter feed.Evaluation of the system has shown that the addition of the online analyser reduces the time lag related to the former method, therefore upset conditions can be reacted more quickly by the control system, and this has resulted in a more stable sintering process. As a result, the sinter feed variability in case of the basicity has been reduced by half. While CaO/SiO2 control was the initial aim of the project, a number of other benefi ts have been realised, such as a reduction in return fi nes and a financial benefi t of 0.11 €/ton of sinter attributed to the reduction of coke breeze and limestone. ThyssenKrupp Steel Europe has identifi ed that additional information available from the analyser could be used to optimise the complete sinter process.The project was carried out with a financial grant of the research program of the ‘Research Fund for Coal and Steel’.

Jul 11, 2011

By E A. Gunn, J Zhou

In this paper a project to develop a joint optimisation/simulation model for production planning in a mine-mill complex is presented. The system involves a mill receiving ore from a number of different locations, each with a unique mineral composition. The mill consists of several crushing and grinding circuits that function in series and parallel. Scheduling the flow of materials through the mill is complex due to constraints on throughput imposed by the millÆs design, the length of time material can be stockpiled on the surface, varying input mineral composition, and throughput targets for a range of output products.An optimisation model is used to create a set of campaigns (ore feed rates) over a given planning horizon under the assumption of deterministic mill throughput. A simulation model is used to evaluate the production plan under assumptions of stochastic machine failure and operational losses created by the need to cycle between input feeds. Campaign scheduling has two important implications for the simulation. First, during any campaign, multiple ore types may need to flow through the mill. However, the mill must be controlled to ensure that only one type of ore can be in a crusher, a grinder or a storage bin at any point in time. Second, as the mill switches from one campaign to another, the set of ores being processed may differ. Thus, the flow of ore through the equipment during a campaign changeover must be controlled to ensure that one or more of the ores from the current campaign can be completely eliminated before the ores from the new campaign are introduced.The simulation architecture employed for this project is Visual Basic for Applications (VBA) combined with MS-Excel as a user interface. A fixed step discrete event orientation is assumed as the simulation framework. A set of model constructs was built for the project with a specific Canadian milling operation in mind, but was designed to be representative of a broad class of milling operations. The constructs are implemented as class objects within the VBA structure, each with a number of properties and methods. The collection of VBA objects forms a composable modelling toolkit. These objects can be linked together by users, via MS-Excel, to represent a broad range of milling operations.

Sep 26, 2011

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By C Simpson

In 2011 the forecasted world demand for iron ore continues to grow, and during this time Australia is looked upon as a reliable supplier of high quality ore. The expansion of the current Australian mines is unlikely to meet the forecast demand. New mines are therefore being actively explored for and when discovered, are quickly being developed into mines in order to meet the world’s hunger for steel.The Solomon Project area is a large new iron ore discovery, located in the central Hamersley Ranges of the Pilbara province in Western Australia. The first Fortescue exploration drill holes commenced on the project in 2007 and to date three billion tonnes (Bt) of iron ore have been defi ned within the project area. Fortescue is fast-tracking the development of the ‘Solomon Stage 1’ project, with rail and mine construction commencing during 2011, and ore to be railed to Fortescue’s existing shipping operations at Port Hedland commencing in 2012. At a designed production rate of 60 Mt/a, the Solomon operation will be one of the biggest production centres of iron ore in the Pilbara.Deposit types include the three dominant mineralisation styles of the Pilbara province, being bedded iron deposits (BID), Channel iron deposits (CID) and detrital iron deposits (DID). All these mineralisation styles are present in large concentrations within the Solomon project area, and when mined will produce two product streams. These are a single product of CID, and a combined product from a blend of BID and DID material.This paper defines the geological characteristics of the Solomon iron deposits as recognised through the exploration and development of this vast resource over the three years since exploration commenced on the project.

Jul 11, 2011

By T G. Vizcarra, T J. Napier-Munn, A T. Karbowiak, M G. Hart

Squeezing extra performance from existing equipment (‘sweating the assets’) is key to continuous improvement initiatives, particularly during times of cost cutting where the option of spending additional capital to facilitate circuit upgrades can be severely constrained. A common challenge, however, is identifying the best combination of settings for different process variables, as their effects can be camouflaged by interactions with other process variables and, of course, noise in historical data.This paper describes a recent investigation at Boyne Smelters Limited to identify strategies to coarsen the product of its dry, fixed-speed, open-circuit AG mill, without the need for installing pre-screens prior to the mill. The product is used as insulation material for the reduction of alumina to aluminium, and an excessively fine product was inhibiting the ability of the cover material to dissipate heat from the underlying anodes. The approach was to undertake a series of experiments, designed according to statistical criteria, to elucidate the effect of key process variables (feed blend and power draw) upon the product sizing. The results provided clarity about what strategies would encourage the production of a more desirable mill product (with some surprises). The study is a good example of how properly designed experiments can identify hidden potential in processing circuits, thereby mitigating the need for capital-intensive upgrades.CITATION:Vizcarra, T G, Hart, M G, Karbowiak, A T and Napier-Munn, T J, 2018. Getting the most from existing processes: using cleverly designed experiments to optimise the line 3 AG mill at Boyne Smelters Limited, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 207–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S J. Clarke, C S. Walker

The South West Rail Link (SWRL) project involved construction of a rail line to service new residential areas in south-west Sydney. The 11 km rail line is conveyed through a short tunnel at shallow depth where it crosses beneath the eight lanes of the Hume Highway. The underpass location is one of the most heavily trafficked within Sydney’s motorway network.The New South Wales Roads and Maritime Services (Roads and Maritime), as the owner of the highway asset, had the responsibility of managing the risks to the highway and traffic associated with the tunnelling project from the pretender stage through to completion. This paper considers the primary risks and mitigation measures employed, including geotechnical investigation, and development of appropriate construction constraints and concept design of an extensive real-time survey system to monitor pavement deformation during the tunnel works.The geology comprises fresh Minchinbury Sandstone in the tunnel invert and side walls, and variably weathered Bringelly Shale in the haunch and crown. Few tunnels have been excavated in these rock types in Sydney, and there is little information relating to the in situ stresses and stress-relief deformations in these materials.During tunnel construction the monitoring data indicated unexpected surface heave of up to about 24 mm. A multiparametric back-analysis of the deformation data is presented, which provides information on the deformation mechanisms and key geotechnical parameters, including rock mass modulus and in situ stresses.The approaches and methodologies developed for the SWRL underpass were effective in maintaining the safe operation and traffic capacity of the highway throughout the construction period, and the analysis of the monitoring data provides a useful reference for similar future projects, or projects constructed in similar ground conditions.CITATION:Clarke, S J and Walker, C S, 2014. Deformation mechanisms of the South West Rail Link underpass beneath the Hume Highway, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 631–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Most of the copper deposits in the Lachlan Geosyncline fall within areas having either a common host rock, mineral assemblage, form of ore body or time and method of emplace- ment. On this basis a Cobar-type ore has been recognised in the deposits of the Cobar -- Mt. Hope - Melrose region. The copper ores in the Tottenham-Girilambone area to the east have a different mineral assemblage. In the more rugged Central Highlands nearer the coast copper deposits are generally concentrated either in one of several Ordovician andesite belts, particularly between Wellington and Woodstock, or within Silurian acid volcanics developed in irregular fashion over a considerable portion of this region. In only a few instances is copper known in the granite batholiths which adjoin these volcanic belts. Native copper and magnetite are characteristic of the deposits of the andesite province and it is possible that future mineragraphic studies will indicate significant differences in the base metal sulphides of both the andesitic and the more acid volcanic belts. Ores having similar mineralogy and form to the Captain's Flat deposit are known at various localities in the eastern segment of the latter belt. In the Gundagai area several small copper deposits with associated nickel minerals have been developed in the Coolac Serpentinite belt.

Jan 1, 1969