Search Documents

The Hemersley Ranges are located in the North West Division of Western Australia and extend, approximately, from latitudes 21¦ 30! to 23¦S and longitudes 117¦ to 120¦E. Their mean height above sea level is'. 2,000 feet, and they rise from 600 to 800 feet. above the gen- eral level of the tableland which extends south-east from the coastal town of Roebourne.. Mt. Bruce, the highest peak, is 4,024 feet above sea level. The ranges are intersected by numerous north-flowing streams, dry during the greater part of the year, which have carved deep gorges, and it is in these that the principal deposits of orocidolite outcrop. The presence -of the mineral was first recorded in 1917., but the deposits remained untouched until 1937 when reports of a strong market demand for-croeido lice resulted in considerable prospecting and mining activity, particularly in Yampire, Wittenoom and Daleis Gorges. . It was established also that the blue asbestos belt extended from Willi- Wolli Springs north-west to Millstream Station, i.e.,-over a.:length of 180 miles and a width of 20 to 30 miles. A number of attempts were made to develop aid treat the Yampire and Wittenoom'Gorge deposits from 1938 onwards, but, for a ,variety of reasons, none of these-proved successful. Current production,. is wholly by Australian Blue Asbestos Pty. Limited at Wittenoom Gorge. This company commenced operations at the Wittenoom Mine in 1946, with an output of 601.8 long tons of- fibre,. and later transferred tb the Colonial Mine about one mile to the north-west. Output has been increased steadily to an' average of 12,000 to 14.,000.. long tons; per annum over the past six years. The total Western Australian output to the end of 1962 is reported by the Mines Department as 110,013 long tons valued at úAl2,403,728..

Jan 1, 1964

By P A. Grossman, J H. Rubinstein, M Brazil

The installation of truck turntables at above-ground crushers has the potential to yield gains in efficiency and productivity by eliminating the need for the trucks to turn around and reverse up to the crusher to dump their loads. The benefits include savings in time, fuel consumption and tyre wear. In addition, having a smaller area near the crushers dedicated to manoeuvring the trucks can be a significant benefit at some sites. Safety is also enhanced using turntables.This paper describes a project with the Australian Turntable Company to develop software that generates near-optimal layouts for the paths taken by the trucks in the vicinity of the crushers when turntables are present or absent. The geometry of the paths is constrained by the turning radius of the trucks and by the boundary of the manoeuvring area. The software quantifies the benefit of installing turntables by generating a design for paths with turntables and comparing it with the layout in current or planned use by the mining company. Through the use of this software tool, a mining company can readily assess the benefits of using turntables at their site.CITATION:Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Demonstrating efficiency gains from installing truck turntables at crushers, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By P B. Hills

Almost a quarter of a century since Bridges (1993) documented techniques for the assessment of ground conditions in a seminal paper in the Proceedings Second International Mining Geology Conference, the necessary role of the geologist in recording geotechnical data on exploration properties and in mines remains. Typically, the geologist is the first professional on the exploration property. Of course, most exploration properties don’t become mines. However, when a property does start to come together and form a coherent mineral deposit and professionals from across the minerals industry spectrum, including specialist geotechnical engineers, become increasingly involved, it remains the geologist who has the most intimate knowledge of the deposit. By association, that knowledge extends to the character of the rock mass.Throughout the various phases of prefeasibility, feasibility, construction and production, culminating in the mature mine, the knowledge of the rock mass held by the geologists continues to grow. In the current era of minimising cost and optimising profit, meeting the requirements and expectations of stakeholders ranging from fellow employees to investors, industry and financial regulators and the broader public, in a social environment where occupational health and safety concerns are of uppermost concern in every endeavour, the value of the geologists’ observations cannot be understated. Mines nowadays employ more geotechnical engineers than they did in the early 1990s when Bridges (1993) wrote his paper. More funds are available for specific geotechnical investigations of exploration properties and mines; none-the-less, those programs remain limited in their extent and there is a wealth of additional data available for collection with the appropriate training, at little additional effort. Fundamentally it is all about the numbers. Any hole not geotechnically logged is a hole that will need to be drilled again if the data is required. Any face, surface or underground, not geotechnically mapped is one that may need to be mapped a second time. That doesn’t mean every hole or every face. However, it is the proposition of this paper that the opportunity for additional geotechnical data to be gathered during traditional geological investigations is an opportunity that cannot be ignored. Occupational health and safety requirements demand that the geotechnical risks associated with mining are appropriately managed. Mining regulations in most Australian and overseas jurisdictions requires the consideration of geotechnical risk through formalised management plans. The Joint Ore Reserves Committee (JORC) Code requires the consideration of modifying factors more than ever before. The benefit to be realised through improved geotechnical understanding by geologists on the ground leads to improved occupational health and safety, optimised reporting compliance, and improved financial and social outcomes for the exploration property and ultimately for the mine that follows.CITATION:Hills, P B, 2017. The necessary role of the geologist in geotechnical data gathering, in Proceedings Tenth International Mining Geology Conference 2017, pp 347–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Reynolds JO

This contribution by. The Australasian Institute of Mining and Metallurgy has three main thrusts. First, an Institute (and industry) view on academia and the need for more entrepreneurship at top academic levels, second the need to lift our technological game, and third, professionalism and the perceived role of mineral industry education. While I will deal with each of these separately they are of course inter- related and can be brought together under the frequently used, but insufficiently practised title, "communications". First then, The Institute and industry view of academia. There are some academics in the audience and I imagine they may wish to reply to my remarks with an academic view of industry. That is not unreasonable. Like all human institutions, academic institutions vary in quality and characteristics. Some are successful and some less so. Some historically are well renowned. Others that were once successful schools have declined. Lesser known schools have grown into prominence. What is it that sets apart 'good' highly regarded schools from those that are not so well regarded? It comes down to one main ingredient - "leadership". The strong mining schools in the past 100 years have been strong because they have had outstanding and clearly identified leaders. Strong clearly identified leadership has always had rapport with, and the support of the industry. The two go hand- in-hand, each nourishing and supporting the Other.

Jan 1, 1986

Although the title of this paper permits a very broad scope for discussion, I propose to deal mainly with those aspects of design part- icularly related to rook filling, the'theme of this conference. The unique suitability of belt conveyors for the continuous economical delivery of materials into or out of underground workings, is well established and needs no elaboration. The facility with which conveyor units, comprised of modern modular components, can be adjusted to lengthen or shorten, their ability to be readily repositioned to suit the develop- ment of a work pattern and their virtues as low noise, reliable transport media, are already accepted by all who are involved with the mining industry.

Jan 1, 1973

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

The Filblast Cyanidation Process incorporating intense high shear mixing, high gas mass transfer efficiency and high oxygen concentrations under conditions of elevated pressure has now been been successfully applied in gold cyanidation mills since May 1993. The first commercial unit had a slurry capacity of 110 cubic metres per hour. Since then 230 and 450 cubic metre per hour units have been installed and a 1000 cubic metre per hour unit has been designed. Laboratory and pilot plant Filblasts have also been built.The reactor is a robust, compact in-line or end-of-line device and may be constructed out of a wide range of materials including wear and corrosion resistant alloys and ceramics. The Filblast Process may be applied to high temperature leaching of refractory gold ores and base metal concentrates.

Jan 1, 1997

By G A. Davis, D G. Laughton

The great variability of mineral and energy prices has motivated some governments to incorporate a windfall profits tax into their mineral taxation regimes. Windfall profits taxes are a means for governments to capture additional mineral revenue when mineral prices are considered higher than some historic level. Governments need to be aware of the effects of such contingent taxes on the exploration, development and operating decisions of mining companies. Mining companies need to be able to calculate the full impact of windfall profits taxes on the economics of their projects. This paper examines the valuation of a multi-phase copper-gold project in the presence of a windfall profits tax. Real options Monte Carlo simulation is used to characterise the different exposures of the mine owner and of the government to the risky cash flow streams that they receive from the project. The results highlight that Monte Carlo simulation paired with the real option valuation method is able to account appropriately for the differing risk exposures, while the traditional discounted cash flow valuation model is not. Our key conclusion for governments and mining companies is that the impact of contingent tax and royalty terms can and should be assessed using advanced valuation techniques, and the results used to improve contract designs under the constraint of actual and perceived fiscal system stability.

Jan 1, 2007

In recent years there have been a number of excellent towns built for mining communities in remote parts of Australia. Planning has been thorough, and very large capital expenditures have been made by companies to provide high standards of accommodation, services and amenities. But so often the phrase 'company town' comes to be applied, expressing the frustrations of the residents, working for a single employer who dominates their lives, and of the company, which would prefer not to have to build and operate a town. The much-vaunted early success of some iron ore, bauxite and coal projects has led to a belief that the success of all mining projects is assured. Those holding this belief ignore the vagaries of mineral deposits and of markets, and the need to amortise large high-risk capital expenditures, much of which is spent on social and industrial infrastruc- ture. This expenditure on infrastructure does not have to be

Jan 1, 1975

The importance of good winding rope practice is stressed. Details of the ropes used for various duties in the four shafts of The Zinc Corporation, Limited (ZC) and New Broken Hill Consolidated Limited (NBHC) are given. Inspection, testing (including non destructive methods), maintenance and rope discard criteria are discussed. There are sane catments about rope installation methods and an appendix is included which outlines the appropriate statutory requirements for winding ropes in New South Wales (NSW).

Jan 1, 1983

The growth of the mining industry around Australia over the last ten years has seen many open cut mines developed on shallow oxide reserves. Most of these have been gold operations, although there are some copper mines in the list, too. Many of these have exhausted their oxide reserves and have made the transition to underground mining to access their deeper sulphide ores. Other operations have reached or are approaching the point where the decision has to be made to go underground or cease mining. This paper discusses the issues involved in making the transition from surface to underground mining. The aim is not to discuss each of the issues exhaustively. This would take a conference in its own right. Nor is it intended to provide a primer on underground mining. Instead the aim is, firstly, to flag the issues which must be addressed when planning to make the transition from surface to underground mining and, secondly, to identify critical aspects of mine development.

Jan 1, 1997

The treatment of steels with acid solutions for the removal of oxide products represents possibly the largest outlet for chemicals in steel processing. Organic pickling inhibitors are required to prevent base metal attack by these acids otherwis

Jan 1, 1980

By Madgwick J

A novel method for determining viable cells of the mineral leaching bacterium Thiobacillus ferrooxidans has been developed. The cells were collected on 0.45/Lm cellulose acetate filters, washed with artificial minewater, and incubated in the presence of ferrous ion at pH3 in an atmosphere containing radioactive (14C) carbon dioxide. Colonies of bacterial growth were detected by the image formed on X-ray photographic paper (autoradiography). The method was compared with three conventional techniques and shown to detect three orders of magnitude more cells in cultures of Thiobacillus ferrooxidans in the late exponential phase of growth.

Jan 1, 1987

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices andoptimisation of the mining method to suit the mining environment.Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave.Prior to the implementation of bulk emulsions an investigation wasrequired to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011