Search Documents

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022

Radioisotope X-ray and neutron techniques of analysis can be used for the determination of a wide range of elements in minerals. The most important applications of these techniques to the mineral industry are for on-stream analysis of slurries and solids, and for geological assay. The radioisotope X-ray techniques are the more developed ones and two installations for on-stream analysis are in routine use in mineral processing plants in Australia. Neutron techniques are being developed, and should prove valuable for geological assay of large numbers of mineral samples, for borehole logging, and for specific on-stream analysis when the cost of the equipment is warranted.

Jan 1, 1969

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By Hoppe AJ

Drilling and shooting techniques at Moura open-cut have evolved over a period of 16 years and are the result of hard earned experience combined with established practices and consul- tation with professional services. The wide range of overburden types encoun- ted in the field requires varying methods to achieve the best results at all times. Safe working conditions for the employees and protection of mining equipment is of para- mount importance and close liaison is maintain- ed with the Department of Mines Queensland to keep abreast with changing legislation. Drill patterns, charging profiles, types of explosives and ultimate results are des- cribed in detail along with a resume of equip- ment. Costs of drilling, labour and explosives are also analysed with a total of approximately 20c per cubic metre of shot ground. Future developments and improvements to facilities are also outlined.

Jan 1, 1978

This case study describes various aspects of establishing a laboratory facility for testing chemically-cemented fill materials. The applicability of data obtained from such a facility related to mine conditions depends on many factors: kind of data, type of testing facility, sample parameters (composition, geometry, size, etc.). The equipment employed must be adaptable, to accommodate variations in sample size and properties. The design, construction and operation of the testing facility is described, and its application to fill samples prepared from sulphides and oxides both chemically and naturally cemented. The present system was selected following an extensive study of equipment available for testing materials in the fields of rock mechanics and construction materials. The strength testing' facility incorporates Linear Variable Differential Transformers for monitoring both lateral and axial displacements during sample compression. The output from these and from other related instrumentation can be recorded or fed direct to a computer, enabling stress-strain data to be printed out while the test is in progress. Also described are controlled environment curing facilities which allow samples to be cured or weathered under different temperature or humidity conditions to simulate long-term ageing and in place conditions.

Jan 1, 1973

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

With mining development on hold and other underground works in a slowdown, the development of nuclear wa te repositories takes centre tage on the American rock engineering scene. Three repositorie for commercial spent fuel-in salt, tuff, and basalt-are in the phase of site characterisation and conceptual design, and one pilot project for defense high-level wa te in salt is under construction. A repository design for crystal line rock has recently been postponed.Because of strict quality assurance requirements throughout design and construction, and because of the need to predict and ascertain in advance the satisfactory performance of the underground openings, much intellectual energy has been expended to analyse underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behaviour and improved methods of underground analysis and design. For the shorter term, a formalised ground control plan was developed, the principles of which may be applied to other types of projects.This paper summarises the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1988

By Pigdon SP, Anderson RM

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of I MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998

Gold mineralization like other low concentration high value commodities has gained the notoriety of being difficult to sample. This adversely affects the confidence that can be placed in resource estimates and ore reserves. As an example, it is not uncommon to find differences of the order of 30% between duplicates of a single sample sent to two different commercial laborartories. Two halves of drill core generally show marked differences in grade. Again differences of 50% are not uncommon in halved core. In the context of this type of "error" within the base data used for the resource estimate, many of the subtleties of computation methods and expert judgement of resource categories, are almost a case of shutting the gate after the horse has bolted. Managers, financiers and consultants must question the quality of the base data upon which resource estimates are made. They must insist that standard and duplicate samples are used to measure the accuracy and precision of commercial analytical laboratories, that sampling practices have been checked for possible bias and give tolerable repeatability. Further they must ensure there can be a realistic confidence in the estimates by correctly using these measures of data quality to quantify risk.

Jan 1, 1990

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Burks WG, Hughes FE, Muceniekas E, Whitcher IG

The area containing the iron field, recognised by the writers, is part of an uplifted, portion of the 'Western Australian Plateau,' ranging in elevation from about 1,000 feet to about 3000 feet above sea level. The local rock succession is flat-lying or moderately-folded and belongs to the Nullagine Series of Upper (2). Precambrian age. This series forms the Hamersley Rangeland vast portions of the...

Jan 1, 1964

Answers to the questions "which rocks contain diamonds?" and "which indicator minerals should diamond explorers look for?" are no longer so easily obtained, now that diamonds are known to occur in lamproites and various types of lamprophyres, as well as their traditional source of kimberlites. One way of isolating those factors (host-rock"geochemistry, geographical or tectonic location, xenolith minerals, etc.) which are most critical in determining the diamond potential of a given pipe, is a detailed and critical re-examination of the huge volumes of accumulated data on kimberlites, lamproites and related rocks. A large analytical database to this end has been set up on an Apple Macintosh II microcomputer using the quasi-relational database management system 4th Dimension. Currently, it contains data for up to 90 major and trace elements, isotopic ratios and contained mineral compositions for some 4,000 rock specimens from all over the world. Many experiences in setting up this database are probably relevant to other geologists setting up their own systems: they include determining the relationships between data items; the advantages of codes over free text in representing categorical variables such as rock types; the need for rigorous error trapping and data validation; and the problem of missing data values and ambiguities thereof. The working system is now being used in a rigorous statistical assessment of the criteria which distinguish diamondiferous from non-diamondiferous rocks.

Jan 1, 1989

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

Analysis of different environmental scenarios and to represent, spatially, of impacted areas is possible by the use of geoprocessing techniques, specifically Systems of Geographical Information (SIG). Through these systems it is possible to create dynamic mathematical models, constituting of a georeferenced digital database and employing the integrated data originated from several sources. In this context, the general goal of this paper is to apply this tool in an environmental analysis of a specific karstic area impacted by mining activities. In order to preserve a limestone site, internationally recognised by its archaeological features, including caverns, lakes and evidences of prehistoric ages, the Brazilian government has created the Lagoa Santa Environment Protection Area. This place is located in the proximity of the Belo Horizonte international airport. In the past two decades exploitations of dimension stones have increased in this area. These exploitations have been done without a mine plan promoting several environmental impacts. The objective of this paper is to analyse these activities using SIG as a basic tool to locate the main mining related impacts and propose mitigation measures including waste and tailings disposal and reshaping of the landscape and introducing a drainage system for the considered zone.

Dec 6, 2010

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Geostatistical conditional simulation is a method to assess variability and risk in mineral deposits and the tool has wide potential applications in the iron ore industry. Correct reproduction of multivariate relationships is important in iron ore simulation, especially between Fe and impurities such as Al2O3, SiO2 and P. The turning bands simulation method, using a full model of coregionalisation for multiple attributes, is the main multivariate conditional simulation algorithm used in the Western Australian iron ore industry. This paper discusses the results of a more recent approach using minimum/maximum autocorrelation factors (MAF) to transform and decorrelate the multivariate data prior to independent sequential Gaussian simulation (SGS). MAF-SGS results are compared to those of the turning bands approach in the Yandicoogina channel iron ore deposit (CID), and both methods performed well in simulating Fe, SiO2, Al2O3 and P distributions. Extensive checking of simulations showed that both approaches could reproduce multivariate statistics and spatial continuity of the original conditioning data. Both approaches reproduced the histograms and variography of input sample composites. While the MAF-SGS approach requires additional transformations when compared with the single normal scores transformation required for the turning bands method, MAF requires only that the direct semivariograms be modelled. In contrast, using turning bands with multiple attributes requires modelling a full linear model of coregionalisation, which can be difficult to model because of the need to ensure the model is positive semi-definite. Turning bands may be preferred if there are a modest number of correlated variables allowing construction of a linear model of coregionalisation that adequately models the multivariate behaviour. MAF-SGS is preferable for larger numbers of correlated variables. Both MAF-SGS and turning bands methods performed well in conditional simulation of correlated variables at Yandicoogina.

Jan 1, 2007

By J M. Santini, I C. A Streimann

Arsenic is a naturally occurring element in the environment and is toxic to biological systems. Arsenic can exist in the environment in the following redox states, arsenite (+3), arsenate (+5), arsine (-3) and elemental (0) (Oremland and Stolz, 2003). Arsenic is released into the environment by natural and anthropogenic activities such as rock weathering and ore mining, respectively. Such activities result in the release of the soluble inorganic arsenic oxyanions, arsenite and arsenate. The redox state of arsenic in the environment is influenced by a number of factors including, redox potential, pH and microorganisms (Irgolic et al, 1977; Genc-Fuhrman, Tjell and McConchie, 2004). Recently, the ability of microorganisms to influence the cycling of arsenic in the environment has attracted much attention. Microorganisms that can oxidise arsenite and reduce arsenate have been isolated and the mechanisms of arsenic metabolism are currently being investigated. The differences between arsenic resistance and arsenic metabolism are being revealed. The role of microorganisms in the release of arsenic into the environment is of particular importance with arsenic contamination of waters causing the death of millions of people worldwide, due to the consumption of contaminated water (Vasken Aposhian et al, 2003; Islam et al, 2004).

Jan 1, 2004

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005