Search Documents

By Coates J. R, Firth I. C

The Imperial Smelting Furnace at Cockle Creek, NSW, was constructed in 1961 and is the oldest facility using the Imperial Smelting process in operation. In recent years there have been significant improvements in many areas of the operation, including production, safety, hygiene and environmental performance. Steps taken to achieve these improvements are described. Plans to secure a profitable future while meeting environmental requirements are outlined.

Jan 1, 1993

Sampling and sample preparation systems at the Hamersley Iron Pty. Limited port of Dampier, W.A., were developed for two separate objectives. 1. The need for rapid determination of physical properties. On stream size analysis enables lump ore and pellet- ized ore physical properties to be monitored and controlled whilst shiploading is in progress. As a control procedure this facility allows optimum shiploading rates con sistent with physical quality control. 2. The need for accurate chemical analysis. Chemical analysis on ship- loading forms the final link in overall quality control procedures encompassing the operation of mining, railway and port blending. Thus maintenance of specification products with minimum variation in chemical characteristics is ensured.

Jan 1, 1976

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By Artmont G. J, Palmer K

Alluvial gold is an ideal exploration tracer to bedrock source and indicator of bedrock mineralisation style because (i) gold occurs in a wide range of deposit types, (ii) primary composition is sensitive to style of mineralisation, and (iii) it is a heavy resistate mineral that is readily preserved and easily sampled. In regional exploration of the Central Ranges of Irian Jaya, alluvial gold mineralogy has been applied to maximise the information return from panned concentrate sampling and to focus exploration effort. Primary gold is a solid solution of Au+Ag¦Cu¦Hg, ¦ trace Pd, Te, and Sb. In general Ag¦Hg increase and Cu decreases with inferred decreasing temperature of formation, and gold from particular mineralisation styles has signature compositions that can be used as indicators of bedrock mineralisation type. Furthermore, the abundance of alluvial gold is an indicator of the economic potential of a catchment. The convergent continental-oceanic plate geology of the Central Ranges is conducive to a wide range of mineralisation styles. Mineralogy of gold in ophiolite, skarn, porphyry, mesothermal vein and possible VHMS environments is characterised from alluvial and bedrock samples, and the use of gold mineralogy in prospecting at regional scale through prospect definition to drilling is demonstrated.

Jan 1, 1995

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

By Walker G. S

Infrared and Raman spectroscopy have been used to study a range of solid state and aqueous solution species which are of interest in extractive metallurgy. In the solid state new Cu(II)/CN'/NH3 complexes have been detected, iron impurities in kaolin characterised, aluminium substitution in hematite and goethite quantified, and the crystallinity and orientation of zircon determined in heterogeneous crystals. In aqueous solution metal cyanide complexes and equilibria were readily characterised, the thermal decomposition of SO2 monitored and products identified, and complexation of AI(III) by hydroxycarboxylates observed. Attempts to monitor the early stages of the gelling of silicate solutions were less successful, with only changes in the gel being detected. However, the degradation of 12-tungstosilicic acid was readily monitored as a function of both time and pH.

Jan 1, 1996

Buoyant levels of world economic growth and recovery in intensity of metals usage suggest that demand for minerals will remain relatively strong into the 1990's. Supply constraints, low stock to use ratios, financial and political factors imply lower elasticities of supply for minerals in the future. The outlook for minerals and metals prices from a pro-ducers viewpoint is, accordingly, promising.The recent recovery in world minerals prices, following strong growth in the world economy over the last few years, makes it appropriate to consider the structural forces at work in the formation of world demand and supply of minerals. This paper will review past trends and consider some of the main economic issues facing the mining industry in the 1990's.

Jan 1, 1990

The rocks of the Serranias Chilla massif of Bolivia are a suite of metamorphosed Palaeozoic basalts and associated continental sediments. Whole-rock trace element geochemistry of the basalts suggest a calc-alkaline affinity and indicate that subduction extended as far north as the Bolivian Altiplano during lower Palaeozoic time.

Jan 1, 1990

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

An integrated mining equipment development organisation is typified by Deutsche Montsn Technologic of Essen, Germany. working on improvements in reliability, production and control in coal mines. Examples of recent mining advances are in mechanised roadheading, in different approaches to cutting technology, and in low height roof bolting.On the longwall face the mechanics of cutting are related to supplied energy as well as to dust make. In conveying both armoured face conveyors and conveyor belts are monitored. Roof support is not neglected and the continuous pumping of stowage slurries provides further options for longwall support. Surveying developments, particularly the gyro-theodolite, directional drilling. and shaft vehicle monitoring provide further examples of advances in control in coal mining activities.

Jan 1, 1991

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are the most common steel-based ground reinforcement used in underground mines in Western Australia. As with any other steel-based product used in underground mines they are susceptible to corrosion, particularly under aggressive minewater and mineral conditions. Because of their thin-wall tubular construction and large surface area, the potential damage resulting from corrosion is considered to be more severe for this type of reinforcement than for other forms of reinforcement made of solid steel bars. Because of the obvious safety problems which may result from corrosion, both mine operators and regulators have raised concerns regarding the long-term effectiveness of FRS installed in underground mines in Western Australia. Although corrosion has been recognised as an important safety issue, the controls of corrosion in varied underground mining environments has not been well understood. To improve the understanding of the corrosion behaviour of FRS, the Department of Minerals and Energy has initiated a research project focused on the mechanisms and extent of corrosion attacks, and their influence on the effectiveness of the reinforcement. This paper describes the research project and presents the interim results achieved To-date.

Jan 1, 1995

Blasting in Norwegian mines is often carried out by contractors who tend to look for the cheapest solution, without concern about fragment quality. The requirementsfor a contractor are usually only related to the maximum size of boulders and the quantity per month. Even when the owners of the mine are responsible for blasting, very little effort is made to optimise the blasting process. This paper presents test methods which were used and results from small-scale and full-scale blasting tests. In the small-scale tests, cubes 500 x 500 x 500 mm of four different rock types were blasted in a chamber, using two types of dynamite explosive. The velocity of detonation (VOD) for the dynamite explosives was 3000 m/s and 6000 m/s respectively. Three cubes of each rock type were blasted with each type of explosive, and a total of six cubes of each rock type was used. The entire muckpile (approximately 350 kg) was- sieved and weighed after each blast and fragments between 8-16 mm were tested for impact values and flakiness. The results of these tests clearly showed improvement in fragmentation the closer the acoustic impedance ratio of the explosive (VOD x density) over the rock (Cp density) was equal to one. The results also showed that the quality of the fragments (in terms of impact values) tends to be better when the cubes are blasted with the high velocity dynamite.

Jan 1, 1995

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

The need to solve the problems associated with spontaneous combustion, system of ventil- ation and methane drainage in gassy coal mines has brought about the development of mining and degassing methods which has made possible up to 80% gas recovery in retreating longwalls. Beneficial results also were obtained mostly in the double or multiple-entry systems, but for single-entry systems and for a seam thickness exceeding 3 m, gas recovery rate is still very low. With some single-heading systems, such as those where a return roadway is not maintained in the goaf behind the face line, a new methane drainage technology is practiced. Attempts were made to extract methane from roof holes drilled from offsets in the ribside of the longwall block. The inclinations and lengths of the boreholes were planned and designed on the basis of the geological and mining condit- ions encountered at the time and every second hole was terminated precisely at the point where the previous hole intersected the immed- iate roof goaf area above the face. There are mathematical relations approp- riate to the design of the above drainage systems to give optimum methane recovery under the given conditions. Some examples of drainage have reached 87% recovery and have attained 94% CH4 purity.

Jan 1, 1982

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

The Macquarie Dictionary defines `information' as: knowledge communicated or received concerning some fact or circumstance; (in communicating theory): a quantitative measure of the contents of a message. For mining companies investing in data capture and information processing technology for operations management is a key issue. Beyond producing performance related information that employees can relate to it is being able to deliver that information into the workplace when it is required, to the employees that can utilise it. To be effective the data needs to be received and understood as `information'. The technology is now available and proven to enable `information' to be delivered into the mining workplace adding value to the activities performed by mine employees. The application of computers and information technology in the mining industry has typically been limited to the resource definition and planning stages, accounting and administration and the process plants that treat the ores and minerals. The mining extraction processes that consume expenditure and determine output in a mining operation occur in an environment dominated by unpredictable events and variable conditions. The mining operation has long been regarded as an inexact science conducted in unpredictable circumstances with many independent variables affecting the output and resultant cost of production. Financial accountants keep track of expenditure and management accountants analyse the cost of production usually on a weekly or monthly basis but all this effort can't affect the outcome, that was determined by the real time events and variations of circumstances over a week ago. Such reporting and analysis can result in conclusions being drawn about what improvements can be made and how you might do better next time, but generally the data is not detailed enough, is inaccurate or misrepresents the real issues. The capital investment required for any mining operation is substantial and comparable to other industries such as manufacturing. The performance and utilisation of manufacturing plants is usually closely monitored down to the lowest level of detail. Many modern plants are controlled and optimised using programmable intelligent devices and monitors display real time performance to the operators and prompt them to make informed decisions to maximise production and minimise wastage. Technology suitable for the mining industry is now widely available and has proven to be a reliable and powerful tool for the optimisation of mining operations. This paper focuses on the latest information technology developed by Modular Mining Systems that has been implemented in mining operations worldwide. The benefits reported by the mining companies utilising real time information technology over the past 15 years have generally related to optimisation of truck fleet allocation and material blending. Some mining operations have reported improvements in equipment utilisation of greater than 20 per cent. With the development of real time graphical display screens in the operators cabins the benefits of information delivery can be harnessed to make employees more effective in the workplace.

Jan 1, 1995

By Cullen JF

Australia has a large resource of manganese at BHP's Groote Eylandt mine which has been progressively developed over the last two decades. While much of the product is marketed internationally to the iron and steel industry, substantial quantities are processed in Australia at the Company's ferro alloy works in Tasmania. In addition, small but increasing quantities of ore are being consumed by the non-metallurgical industry. Fluctuating fortunes in the steel industry produce similar trends in the marketing of manganese. The increasing cost of freight and power together with strict environmental control is further affecting the market balance. Mine operators are expanding into the alloy making field. Reduction in usage in less developed countries is occurring.

Jan 1, 1982

By A Jewbali, R Perry, R Inglis, L Allen

"The use of conditional simulation to characterise mine plan uncertainty is increasing for the assessment of risk in mining projects. While the development of grade uncertainty profiles is relatively straightforward and can be validated using standard geostatistical techniques, the addition of geological uncertainty to evaluate total risk remains problematic. Some of the problems associated with geological uncertainty methods include the clustering of data in favourable geologic units, difficulty in training image definition and the inability to address change of support issues for categorical variables. Despite these obstacles, the importance of geological uncertainty as a contributor to total uncertainty has prompted Newmont to explore and evaluate the use of various techniques (and combinations of techniques) on different deposit types.Two orogenic deposits of different geological complexity were selected for the study: Subika, a shear zone-hosted deposit, and Merian, a deposit containing gold mineralisation associated with quartz vein zones and stockwork within which are found higher-grade quartz breccia zones. Newmont trialled various categorical simulation approaches to determine the applicability of these methods for each deposit type and the effect of parameter choice on the width of the uncertainty interval. Some of the techniques that were trialled include multiple point statistics methods, sequential indicator simulation using local probabilities as well as variations of these methodologies.The goals of this study included: gaining an understanding of which techniques may work best in which deposit types gaining an understanding of the intricacies of each method gaining an understanding of the effect that each method has on total uncertainty analysis.This paper presents a comparison of the various techniques and makes recommendations for their use in uncertainty analysis.CITATION:Jewbali, A, Perry, R, Allen, L and Inglis, R, 2014. Applicability of categorical simulation methods for assessment of mine plan risk, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 85–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By F R. M Pires, Y Hasui, A Schrank

The iron ores of Alegria mine are composed of itabirites enclosing minor bodies of high-grade ores. The itabirites are classified according to mineralogical composition in five types: martite-rich, goethite-rich, specularite-rich, magnetite-rich and anphibolite-rich ores. The hematites are martite-rich, magnetite-rich, specularite-rich and more rarely, amphibolite-rich. Other classification criteria of the ores are based on the physical properties and the degree of compaction. As such, the itabirites and hematites can be classified as hard, friable and soft types. The mineralogical/textural evolution of the ores is linked to the pressure and temperature conditions that accompanied the tectonic processes in anphibolite facies and the different degrees of subsequent surficial weathering processes. Petrographic and microstructural studies indicate that the magnetite and amphibole bearing itabirites represent the parent rocks that created the other itabirites and that the specularite itabirites and the hard martite types are related to silica dissolution and redeposition in zones of high and low strain. Most of itabirites ores correspond to chert oxide facies banded iron formation, except the goethite and amphibole bearing itabirite that resemble a silicate or oxide-silicate facies with minor carbonate impurities. The great mass and pods of soft martite itabirites are probably shaley oxide facies BIFs with little volcanic contribution. Trace element contents of the AlegriaÆs itabirites show strong dissimilarities with BIFs associated with volcanism (Algoma type), but closely ressemble to the Lake Superior type, with high content in Cr, Co and low V, Ni, Cu and Zn. Although the absolute contents of REE present in the AlegriaÆs itabirites are, in general very low, the pattern when normalised by NASC is similar to the great majority of the Archean and Paleoproterozoic BIFs elsewhere in the world, and characterised by positive Eu anomaly.

Jan 1, 2002