Search Documents

Longwalling has reached a high standard both in Germany and Australia and most improvements should be expected in planning, monitoring and control. Double drum shearer have electric drives to 1000 kW and automatic height control is under development. Conveyor pans to 40mm thickness and chains to 2300 kN breaking load are in use with controls for pretension and load compensation under test.Trends in support are towards two leg shields with loads to 3850 kN per leg and electrohydraulic controls. Expert systems have been devised for planning and diagnosis tasks. With increases in technical standards, staff qualification standards at rising too, drawing attention to training requirements for modem personnel.

Jan 1, 1991

A new test coke oven of seven cubic foot capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from the flues on either side of the charge. The method of charging permits close control of charge conditions'such as bulk density and moisture content. These conditions, as well as coking conditions (e.g. flue temper- atures., coking time) must be varied to simulate conditions in different batteries, The effects of several variables on coke quality are discussed. Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes; for 17 tests, the average A.S.T.M. stability and hardness indices for the test oven coke were 38,5% and 69.7%, while those for the battery coke were 37.1.% and 67.6%.

Jan 1, 1969

The preferred alternatives in heap design and their motivation are identified as- -normal heap leaching, to be generally applied wherever possible, - flooded vat leaching, to be appliedwhere wetted ore lacks adequate cohesion or if limited space necessitates it,- thin layer leaching, to be applied where deleterious vat chemistry necessitates it.A number of the following features would probably be incorporated in the optimization of normal local heap leach operations- pre-cyanidation - pre-agglomeration - retaining walls- staged (counter-current) heap treatment- control of calcium levels- reduced pH and trickler irrigation

Jan 1, 1984

Like almost any other 19th century mining area, the West Coast saw its 20th century scrapping era when machinery which had been installed in seemingly inaccessible places was somehow dragged out again. Fortunately there were some spots so remote that they defied even the most zealous of these pioneering recyclers. One of these was Big River, a mining locality in a rugged landscape straddling the headwaters of the Grey and Inangahua rivers. As a result there remains an internationally important collection of mining equipment including a poppet head, two steam winding engines, a pair of boilers, part of an aerial cableway with its loading system, and remnants of a stamp battery along with its associated gold smelter, cyanide tanks and zinc boxes. There are also assorted building remains associated with 60 years of mining and settlement. Since their abandonment in 1942, these relics have all somehow survived a further half century in a far from favourable climate with two or three metres of rain a year, frequent snowfalls and hot summer temperatures. The rate of decay during the past few years has been alarming.

Jan 1, 1996

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operations at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry.Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle ize distributions and brightness values have been prepared.Extensive drilling and bulk sampling of the deposit over eight years has shown that the orebody is large and of a high grade suitable for the production of premium quality coating kaolins.The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW).The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment, the nature of the production process and details the project management procedure used for the design, construction and commissioning of the plant. Three areas of significant interest, the gas turbine fired pray dryer, the moving bridge shiploader and the use of aerobelt conveyors on the project are detailed.

Jan 1, 1988

Many metallurgical beneficiation and primary concentrating processes rely upon discrimination of products from gangue based on particulate density of the different minerals and combinations of minerals in an ore. The basic definition of density is simple, but the apparent density that minerals exhibit when in the environment of commercial densimetric separation processes is more complex and is ill-defined. Measurement of the apparent density displayed by minerals in their separation situation is essential if modelling of plant performance is to be meaningful or when comparison of an existing operation with a æperfectÆ separation constitutes a part of an audit or of a plant control function. Seven methods of dividing ore samples into discreet density fractions are examined and criticised in this paper. The shortcomings, difficulties and potential errors arising from the use of each method are evaluated. Most of the techniques described have been used by the author and generally their faults are understood and the resultant first-hand experience has been used to overcome these faults. A simple new computer-assisted technique for developing meaningful densimetric data is described.

Jan 1, 2004

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

The exploration and mining risks are investigated and compared to the risks of smelting, secondary processing and other normal industrial activities. This study concentrates on the risk before, or at the investment decision. Internal and external risks are distinguished. Internal risks are the risks inherent in every engineering design and common to all projects. The main external risks are the financial risk, changes in prices, location problems and geological factors. Financial risks concern every capital-intensive and export-oriented project and cannot be considered as typical mining risks. Changes in prices, i.e. the market risk, concern every industry using raw materials, but the market risk is especially accentuated in the mining industry. Problems of location and infrastructure are normally more significant in mining than in other projects, and geological risks are unique to mining. All these risks associated with mining projects combine to form a risk at least twice as high as that for other normal industrial activities. Within the range of profitability of mines, which on average is the same as in the manufacturing industry, only a few highly profitable mines exist. These few mines are the sole reward for the high risks taken.

Jan 1, 1986

By Ennis P. C

The Mt Keith ultramafic intrusive extends for about 200 kilometres from Agnew in the south to Wiluna in the north. It forms the host for a number of nickel sulphide orebodies including Mt Keith and Honeymoon Well. Long fibre minerals are associated with the orebodies. The presence of these minerals impacts on the issue of tailings disposal from several standpoints, particularly the slurry beaching properties and dust generation from dry beaches. Central thickened discharge (CTD) is an innovative method of tailings disposal that involves stacking tailings in a low conical hill instead of storing them in cells. In appropriate circumstances this leads to savings in capital costs and operating expenditure. The method was introduced to Australia in 1981, and is currently employed at four operating mines, Elura and Peak Gold, both at Cobar in NSW, McArthur River in the Northern Territory, and Union Reefs near Pine Creek, also in the Northern Territory. It is the proposed method for Century Zinc and Ernest Henry, both in Queensland. The paper describes laboratory test work and design parameters for the application of the method to tailings disposal at Honeymoon Well and compares them with comparable data for other CTD systems. Of particular relevance for design purposes are beach slope, density, and water recovery. Wind tunnel tests were conducted on the Honeymoon Well tailings samples to investigate dust generation from the dry beach surface and it was concluded that dust generation from an undisturbed beach would not occur because of crusting.

Jan 1, 1996

By Moore J

Gunpowder Copper Ltd is using in-situ leaching to extract copper from the Mammoth sulphide ore deposit in north-west Queensland. To increase metal recovery, ore is fragmented using conventional underground longhole drilling and blasting techniques. Although the upper levels of the orebody had previously been mined by open cut and underground methods, significant reserves of copper existed around old workings. To safely and economically recover this resource, a decision was made to fire the remaining pillars in the upper part of the mine by a single 1.37 million tonne mass blast in February 1992.This paper records the planning, design, and implementation of the Mammoth mass blast. Geological and geotechnical aspects are summarised, to explain the reasons for such a large blast. Drilling, charging and blast initiation are discussed in detail, to show how standard equipment and products were applied to a unique task.

Jan 1, 1992

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

By Hommert P. J, Brown B

Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. An improved damage model based on microcrack growth in tension allows finite element calculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model.

Jan 1, 1990

By Willis GM

The matte-metal-equilibria in the system Pb-Cu-S have been studied at temperatures between 720 and 920¦C by direct sampling and D.T.A. methods. These results are compared with those of other workers. The applications of such data to a continuous copper drossing process, and to a number of other metallurgical processes are discussed.

Jan 1, 1975

Broken Hill has a long history of mining and it is without doubt a world-class deposit. It has seen production since 1885, notwithstanding the strikes that made the city infamous in days gone by and has given rise to three of the nation's leading mining companies; BHP, North and CRA. Prior to the formation of Pasminco in 1988, the mining and exploration activities were undertaken by separate companies who were business competitors and tended to operate in relative isolation. There were a few notable exceptions such as the Central Geological Survey of 1936 - 38 (Gustafson, 1939; Gustafson et al, 1950) and the Mine Managers' Association. The latter sponsored many university based research projects. At a local level there was good communication and cross fertilisation within this remote outback centre through personal contacts and professional bodies such as The AusIMM. Pasminco was formed by the merging of the lead-zinc interests of CRA Ltd and North Broken Hill Ltd. In Broken Hill this meant the joining together of North Mine and ZC Mines, the two largest mines then operating on the Line of Lode, to form Pasminco Mining Broken Hill Operations. The exception was the central part of the orebody, the original BHP, South Mine and

Jan 1, 1997

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

By Readett D. J

Soluble salts can be removed from Bowmans lignite by water and acid leaching. The success of the removal of water soluble or acid exchangeable impurities is directly associated with the efficiency of dewatering these slurries. The filtration characteristics of a slurry at its natural pH (4.0) were poor, with a filter cake moisture of 65%. Acid treatment of the slurry at pH2 caused the filter cake moisture content to drop to 61 %. Various oils, oily surfactants and a flocculant were tested to determine the conditions for minimum filter cake moisture. A series of pilot scale filtration tests were conducted on flocculant dosed slurries with and without washing on a horizontal test unit. Moisture contents of 54% were obtained in laboratory testing using high additions of oily surfactant. For the pilot scale test work, moisture levels close to 60% were obtained with low flocculant additions, similar to results obtained in laboratory studies. Removal of soluble salts could be correlated directly to the final moisture content of the filter cake. This process of leaching followed by filtration resulted in the removal of approximately 75% (more than 80% with washing on the cloth) of the sodium chloride originally present in the lignite.

Jan 1, 1989

By F Hungerford

"In-seam drilling has been undertaken for the past 30 years for gas drainage to reduce the risk ofoutburst and lower the concentrations of seam gas in the underground ventilation. The drillingpractices have reflected the standards of the times and have evolved with the development oftechnology and equipment and the needs to provide a safe environment underground. Earlypractice was to adapt equipment from other fields, but with changing emphasis, research anddevelopment by the coal industry has created specifi c equipment, technology and practices toaccurately place in-seam boreholes to provide efficient and effective gas drainage."

Jun 1, 2012

By Fradd WP

South Australia pioneered metal mining in Australia and was the main source of copper for several decades. Gold discoveries and mining also contributed significantly to the development of the Colony. Across the State can be seen the holes, the mullock heaps and, in some instances, the remnants of machinery of the past era. In this, the centenary year of the discovery of the Teetulpa goldfield, considered by some to he the most significant discovery of gold in the State, it is appropriate that we should present a paper on the history of gold mining in South Australia. South Australia has not been a major producer of gold with recorded production a little in excess of 15 million grams (15 t). This represents about 0.25 per cent of the Australian total and ranks last of the States of the Commonwealth. The outstand- ing feature of gold production in South Australia has been the succession of short periods of rela- tively high production immediately following a discovery, with payable dirt being quickly exhausted, a fact clearly illustrated by the graph of South Australian gold production (Figure 1).

Jan 1, 1987

By Hirose K, Itakura K

A new global stiffness matrix evaluates the performance of powered supports by estimating and comparing the global stiffness matrices of ten different types of powered supports with lemniscate linkages, each support having its own deformation characteristics. Expanding the global stiffness matrix allows the implementation of a finite element scheme to analyse the interaction between the powered support and the strata around the coal face.The evaluation of performance by the stiffness matrix method shows that 4-leg chock shields possess both the desirable convergence and shear deformation stiffness properties. The finite element analysis also confirms that 4-leg chock shields present well balanced performance for controlling strata around the coal face.

Jan 1, 1991