Search Documents

By Q Zhou, G Barrett, Y Choi, J Jiang

As part of a general review of processing double refractory ores through Barrick GoldÆs autoclaves /carbon-in-leach (CIL) facility at Goldstrike, a study was made to evaluate the use of surfactants for reducing the loss of gold during cyanide leaching of preg-robbing gold ores. Consistent improvement of gold recovery was observed with surfactants at various testing conditions. This paper will discuss the results obtained from laboratory and pilot-scale testing, as well as, review potential mechanisms for the observed improvement in gold recovery.CITATION:Zhou, Q, Barrett, G, Jiang, J and Choi, Y, 2013. Surfactants for gold recovery improvement with preg-robbing gold ores, in Proceedings World Gold 2013 , pp 367-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

GENTLEMEN, I have to thank you very much for the honour you have conferred upon me by electing me President of the Institute for this year. On behalf of resident members, I have to offer the visitors a very cordial welcome to Mount Morgan, and to tell them that all arrangements have been made to enable them to inspect the mine and works at their own convenience, and to supply them with any particulars they may need.It is very pleasing indeed to see such a large gathering, especially on account of the long journeys many have undertaken in order to be present. The first congress in Queensland, about eleven years ago, was attended by a comparatively small number of members, and a rather long time has been allowed to pass in consequence. The large attendance at this meeting encourages the holding of meetings in Queensland more frequently. Owing to the long distances, and the number of mining centres in Australia and New Zealand, we cannot expect to meet oftener than once in six or seven years in...

Jan 1, 1911

By Howarth W. J, Sowerby B. D, Watt J. S

On-line analysis systems have found widespread application in the metalliferous mineral and coal industries. The continuous analysis and rapid response of these systems has led to improved control of mining, processing and blending operations, with increased recovery of valuable minerals and coal combustibles.The paper reviews developments in on-line analysis by CSIRO and Mineral Control Instrumentation Ltd which led to the award of the Australia Prize 1992. These commercialised systems analyse mineral and coal slurries; determine the ash and moisture contents of coal on conveyors, and the moisture content of coke on conveyors; and determine the carbon content of fly ash. These gauges are estimated to have resulted in productivity increases valued at $50 million per year to Australia.

Jan 1, 1993

By J Langhans, Y Choi, Q Wang, J Y. Baron, P Kondos

Barrick has successfully developed the thiosulfate leaching process to treat sulfidic high preg-robbing ores. The process was developed through rigorous bench test programs and proved in pilot campaigns and demo plant operations. The process uses calcium thiosulfate as a leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recovery. The thiosulfate leaching plant is under construction as a brownfield project and the start-up is planned in 2014 at Goldstrike, Nevada, USA, one of BarrickÆs operations.CITATION:Choi, Y, Baron, J Y, Wang, Q, Langhans, J and Kondos, P, 2013. Thiosulfate processing - from lab curiosity to commercial application, in Proceedings World Gold 2013 , pp 45-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By Corrans I. J, Yan D. S

The CIP process for gold recovery has enjoyed widespread application in most gold-producing countries. The development of a mathematical model of the CIP process has value for use in process design, process optimisation, and process control. Mathematical model development through laboratory experimentation is an important step in the design and optimisation of the CIP process. For this purpose, data has been generated through small scale laboratory leaching and adsorption tests both in batch and continuous mode. This test program has been carried out on specific ores of various types prior to the application of the models to production CIP plants utilising these ores. The applicability of leaching models derived from batch experiments was tested in a continuous five stage CIP pilot plant. The models were then adapted to scale-up the batch to the small scale continuous operation.

Jan 1, 1991

By A G. Greenwood

Research into cemented rock fill at Mount Isa Mines Limited since 1992 is described. The key mechanisms controlling segregation during stope filling with cemented rock fill are described and include the gravity flow mechanism which is described in detail. Examples are provided to demonstrate these mechanisms. Comparisons are made between Mount Isa MinesÆ cemented rock fill and slurry-based cemented rock fills. Recent backfill stability modelling using a three-dimensional finite element program is described.

Jan 1, 1998

By S Wotherspoon

At Kalgoorlie Consolidated Gold MineÆs (KCGMÆs) Fimiston Operations, located on the periphery of Kalgoorlie Boulder in Western Australia, roughly 7.5 million tonnes of rock are broken each month for the extraction of gold. With the close proximity of neighbours to the mining operations in the Chaffers Cut Back, special blasting techniques and tools were employed by KCGM to manage the blast induced vibrations and noise in this area. The i-konTM initiation system coupled with OricaÆs complementary modelling and analysis tools offered the complete blast management package. With these tools KCGM management and Orica Mining Services commenced an investigation into the benefits of electronic initiation. Prior to the commencement of electronic blasting, initial modelling was conducted to examine the vibration time waveforms and their frequency content, as these were expected to have an impact on vibration interaction with structures such as large buildings and urban dwellings. This work looked at results measured for a previous conventionally (pyrotechnic) initiated blast in the area and compared it to the results obtained when the blast was modelled with electronic initiation and faster timings. The predicted peak particle velocity (PPV) and structural vibration factor (SVF) were calculated. From the results it was concluded that the investigation into using i-konTM electronic initiation system and SHOTPlus«-i blast design software had some real potential to improve blast vibration management on the cut back. The use of the electronic initiation system and complementary software allows intricate timing designs to be accurately placed into blasts. The system has a number of working modes that allow either the precise design timings to be logged automatically into each detonator or to be manually logged where a variation from the design exists. Where such variations from the design occur, the electronic system permits the actual timings used to be uploaded back into the design file. This allows both design and real actual timings to be stored for future analysis or reference.

Jan 1, 2004

One of the most difficult places to ventil ate in any mine is the working face area of an advancing mine heading. With an ever changing configuration, continual modification and extension to the ventilation system is necess- ary to maintain an adequate supply of fresh air and to control mixing and recirculation. Methane emissions and high dust levels as coal is broken and removed from the face area can produce unhealthy and dangerous conditions if ventilat- ion is not adequately monitored. An understanding of the air flow patterns which develop through use of different face ven- tilation systems can be reached by undertaking underground measurements or through observations using physical models. Tests undertaken by the author to determine the adequacy of different system-configurations are discussed together with approaches adopted by others working in the United States. Various new methods have been proposed for improving face ventilation beyond that sustained using conventional brattice curtain or tubing systems. The adequacy of some advances adopted by mining companies to improve ventilation while maintaining output efficiency is discussed.

Jan 1, 1983

The Mt Whaleback open cut mine South Wall is, in part, developed as an unbenched dip slope. The remainder of the rock slope consists of asymetrical overturned folds which have been locally truncated by major low angle faults. The Mt Whaleback orebody is structurally controlled and therefore extensive structural geology input has gone into the final rock slope design. The design is based on normalised 40 m geological cross sections, but the inherent complexity of the geological structure of the orebody yields a high degree of uncertainty within that interval. There- fore, the final slope bench face and the penultimate bench faces are mapped in detail to accurately establish the geological contacts and struc- ture. The knowledge of accurate geology of final and penultimate faces plays a very important role in the design of controlled perimeter blast- ing. Accurate geology is established mainly by face mapping, and by hole geological evaluation of blastholes to locally refine the current Geologi- cal model.

Jan 1, 1989

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

BHP is the world's largest copper concentrate producer with production from mines at Escondida (Chile), Ok Tedi (Papua New Guinea), and Island Copper (Canada). The entire concentrate production is further processed into refined copper by third-party smelters around the world. In anticipation of an expansion in the global copper concentrate production capacity and a corresponding increase in treatment and refining charges by copper smelters, BHP has continuously evaluated various opportunities for downstream copper processing. An expansion in the Escondida mine production, combined with BHP's interest in processing some of its concentrate production on-shore in Chile, ultimately resulted in the development of the Escondida Leach Process. This process was specifically developed for higher grade concentrates, such as from Escondida. An ammoniacal lixiviant and air are used under ambient conditions to leach less than one-half of the contained copper values. After solid-liquid separation, the solution is subjected to solvent extraction regenerating the ammoniacal lixiviant and the copper loaded organic phase is stripped in spent electrolyte returned from the electrowinning plant where ultra-high quality SX-EW copper is produced. The solid leach residue can, if required, be upgraded by flotation to produce a high-grade copper concentrate with improved fuel values and a pyrite tail for disposal. After an 18-month bench and pilot plant scale program and an engineering feasibility study, Minera Escondida Limitada decided to build an 80 000 tonnes of copper per year facility near Antofagasta, Chile. The installed investment cost amounted to around $160 million. The plant went into commercial production in November 1994 and better than 99.9995 per cent Cu cathodes were produced right from the start. BHP believes that the process and the commercial plant are an excellent example of a novel approach advancing the science of copper metallurgy in harmony with present demands for environmentally sound processes and high quality products.

Jan 1, 1995

By C McIntosh, M Carder, P M. J Durance

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Disseminated, gold-bearing sulfide minerals hosted in sheared, wall rock metasediments and clay alteration zones comprise one of the dominant styles of Palaeozoic orogenic gold mineralisation within the Reefton Goldfield, and is exemplified by OceanaGold’s Globe Mine. This study begins the exploration and characterisation of the gold-arsenic-antimony mineralisation hosted within the dominant lithologies of the Globe-Progress shear zone. The main gold-bearing sulfides are pyrite, arsenopyrite and stibnite. Pyrite and arsenopyrite are not compositionally uniform across the Globe-Progress shear zone. Pyrite from the mineralised greywacke and argillite has higher As contents than pyrite in the host rock and pug breccia. Furthermore, the mineralised greywacke and argillite pyrite are enriched in As from core to rim. The 3D models based on bulk assays reveal a significant correlation in the distribution of Au, As and Sb. The interpolant for Sb envelops those for Au and As, which in turn are very similar to each other in their vertical and lateral extents across the shear zone. This result is consistent with earlier findings that the occurrence of stibnite represents a separate and likely later phase of mineralisation relative to that represented by the formation of disseminated pyrite and arsenopyrite both of which exert a stronger control on the distribution of As.CITATION:Durance, P M J, Christie, A B, McIntosh, C and Carder, M, 2015. The composition of disseminated, gold-bearing sulfides within the three-dimensional framework of bulk Au, As and Sb in the Globe-Progress orogenic gold deposit, Reefton Goldfield, New Zealand, in Proceedings PACRIM 2015 Congress, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Sasol Roche Blasting Services (SRBS) has undertaken a process of trialing and evaluating the use of the SMI electronic initiating system with the specific purpose of being able to fully quantify the benefits of the system over a pyrotechnic system. After an initial trial of three shots in mid-2001, it was decided that to fully quantify the system, a complete strip would need to be fired using the system so that any losses due to ramps or end walls would be the same for both scenarios. The results have shown a significant improvement over the use of pyrotechnic initiators in several key areas including percentage cast. Through the use of survey results, the increase in cast and subsequent net improvement in blasting has been quantified. These trials have set out to compare each system in comparable situations to determine the real benefits, if any, of the electronic system over the pyrotechnic one. As the percentage cast is relatively easy to quantify using modern survey techniques, it was decided that this would be the principle method of comparison. However, while the assessment only included survey results, any improvement in fragmentation size and consistency would have flow on effects on reduced running and maintenance costs.

Jan 1, 2003

High interest to basic-ultrabasic rocks is ex-plained by their specific, sutural, geotectonic po-sition and by deep level of generation of ultraba-sic magmas. These two factors allow us to treat this group of rocks as valuable source of informa-tion about the lower crust and upper mantle of the Earth. Basic-ultrabasic xenolith series is another source of information about the interior of the Earth. Detailed studies of the xenolith series give valuable material to geologists as to how endogenic deposits are fed and what is their source.Besides, the interest is explained by attempts to understand the relationship between basic-ultra-basic complexes and deposits of metalliferous and non-metalliferous mineral material.Absence of genetic boundaries in manifestation of metalliferous and non-metalliferous minerals, their temporal and spatial relationship allow us to treat the minerogenesis of ultrabasic complexes as a result of one ore-forming process manifested in Koryak-Kamchatsky, Sakhalin-Japanese, Ryukyu-Korean and Taiwan-Philippines island arc systems which re-present, in the opinion of the authors, one eastern Asian chain of the Pacific ore belt (Radkevich, 11)87).

Jan 1, 1990

Developed and built in 1982 for simultaneous bathy-metric and reflectivity mapping of the deep ocean by the Hawaii Institute of Geophysics, SeaMARC II was a breakthrough in sea-floor mapping technology. The design was developed cooperatively by industry and academia, and the system has served as a prototype for a new generation of mapping tools for operation in both shallow and deep water.Research programs using the SeaMARC II system have focussed on basic research into the geophysical evo-lution of the Pacific, ranging from intra-atoll mapping to surveys of the deep-sea trenches. During the past few years most work has been concentrated on detailed investigations of the morphology of mid-ocean spread-ing centers, seamounts, and the subduction zones which surround the Pacific. The detail provided by the high resolution, 10-km wide side-scan sonar images of fault and fold structures, combined with the swath of bathy-metric information obtained simultaneously, allow previ-ously unattainable analysis of seafloor morphology and are leading to development of detailed models for ocean crust genesis and deformation.

Jan 1, 1990

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important alvantage. of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate: (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elim-ination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the thresthold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step copper smelting is still a process of the future.The paper describes the potential advan-tages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By Y Li, L Zhang, G Li, S C. Dominy

Qiagong skarn iron (copper) deposit is located in Xietongmen County of Tibet, China (N 29¦52Æ14.9ö, E 88¦24Æ10.3ö). It is situated at the middle-western Gangdese porphyry copper-belt. Mineralisation is related to a Himalayan porphyry intrusion, with the mineralised body occurring at the contact zone between the Tertiary Takena Formation carbonate rocks and Himalayan monzonitic granite porphyry. The melt, melt-fluid and fluid inclusions were observed in early quartz, with most abundant fluid inclusions in quartz, calcite and garnet from the skarn. The geology and inclusion assemblage show a close relationship between iron (copper) mineralisation and a Himalayan porphyry intrusion. Based on preliminary inclusion studies, this paper discussed the characteristics, evolution of ore-forming fluid and affiliation to the Himalayan porphyry intrusion. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

To obtain the best economic results in treating the comparatively high-grade ore of the Kalgurli Mine a good roast is essential, and the effort of this paper will be to briefly describe the plant and the conditions prevailing in roasting, which, on an output of about 360 tons daily, subsequently enable an average extraction of slightly over 94% of the gold to be maintained.The percentage of sulphur in the ore varies between 2'5 and 3'5, the lower figure existing when treating oxidized ore. The average gold value is 13 dwt; this occurs chiefly as sylvanite, containing .a lower percentage of silver than is usually present in that mineral. One ore body in the mine contains hessite (Ag2Te) in considerable quantity, associated with gold telluride, and when ore from this stope is being treated the silver contents rise to as high as 20 dwt, but the usual amount is about 9 dwt. per ton, of which only a small proportion is extracted. Other metallic minerals, in addition to pyrite, occurring more or less commonly, are arsenopyrite, magnetite, chalcopyrite, and the tellurides calaverite (AuTez)and coloradoite HgzTe3). A small proportion only of the value occurs as free gold.

Jan 1, 1911