Search Documents

By Shu DM, Moxon P

Subsidence profiles over longwalls at West Cliff Colliery (WCC) are predicted by three methods, NCB Emperical Method, Salustowicz's Profile Functions and Superposition of Two Critical Profiles. A method of deriving maximum subsidence using local data is also presented. For the first four longwalls, the results are compared with those from the subsidence surveys conducted during and after the extraction of each longwall. Longwall V has not yet been extracted, so the results are for the predicted subsidence profile. Superposition of two critical profiles is carried out in an attempt to check the principle of superposition. In addition, strata movement above the extracted longwalls is discussed.

Jan 1, 1986

By Hematian J

A high horizontal stress field has significant effect on the stability of underground roadways and influences the design of a support system in this environment. The high horizontal stresses at E1lalong Colliery, NSW, Australia provided the environment for this study. Samples of coal measures 'rock were collected and tested to determine their mechanical properties. The lithology, stress state, geometry and conditions prevailing in particular areas of the mine were obtained from geotechnical reports available at the mine and by field observation. The results of a series of finite element models constructed and tested under various conditions provided a basis for comparison with field observations. Analysis of the results indicated sufficient correspondence to provide a basis for the proposed design of an optimum support system. It is not suggested that finite analysis provides 'exact answers', but it does show the relative importance and interaction of various parameters.

Jan 1, 1995

By Boger D. V

Two industrial case studies in which detailed investigation of the flow behaviour of mineral slurries is used to assess the feasibility of pipeline solid transport are described. The first example deals with the pumping of highly concentrated bauxite tailings to disposal, while the second exam- ple examines the possibility of transporting high-density Victorian brown coal slurries which previously has been thought as uneconomical. It is demonstrated that these typical solid handling problems can be solved by a good understanding of the rheology of suspensions.

Jan 1, 1989

By Delahey G, Dunne R

At New Celebration Gold Mine the advent of treating primary sulphide ores resulted in decreased gold recoveries of four to ten per cent. The grind coarsened due to an increase in ore hardness and gold in the residue was found to be associated with pyrite. Finer grinding improved recoveries but was impractical as production rates would have decreased to unacceptable levels. An alternative approach that has proved to be viable combines both gravity separation, to recover the coarse gold bearing sulphides, and then regrinding the concentrate in a tower mill prior to releaching in the cyanide leach circuit. The tailings treatment plant was commissioned in December 1990 and details of the first 18 months' operations are Provided.

Jan 1, 1993

By Flierman GA, Van Toor CH

Investigations were carried out of burden distribution using a full scale model of the furnace top. Various charging sequences were used and large differences were found between ore charged as sinter-pellets and as pellets-sinter. These were attributed to the differences in the angle of repose between the two materials. Permeability index was defined which was independent of the driving rate from which a furnace resistance index was obtained for use in weekly reports. Results are summarised as a single expression between blast rates and pressures and the values of Qbl and Qmax are continuously measured to aid the operators in controlling the wind rate in the safe AP region. Results also indicate a reserve in capacity of No. 7 BF.

Jan 1, 1975

Esso-BHP have installed a Production Supervisory Control System that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control. The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexability to handle future variations in operating conditions. Thn -etom ..ill kn nvt,,ndnd to thn I-lalihn+ rJ,+f, rr , Into +hie -- -A +n the lei...,fieh .,lo+fnrmc A.,;- 1071

Jan 1, 1970

By Katom M

Each of the two 32 feet diameter Semi Autogeneous Grinding (SAG) mills at Ok Tedi's copper and gold concentrator was treating at best 1500 tph at about 65 per cent mill availability in 1988. The process was effectively unmeasured and used manu

Jan 1, 1997

By Christie AB, Bull VH

The geological environments of gold deposits are reviewed in relation to the strong resurgence in exploration for gold since 1979. The resurgence is due mainly to New Zealand's geological endowment with gold and its history as a gold producer. Major past production was from Cenozoic placers of Otago and Westland, late Cenozoic epithermal deposits of the Hauraki Goldfield, and the respective Paleozoic and Mesozoic lode deposits of the Reefton and Otago Goldfields. These same geological environments are the targets of current exploration, mainly in extensions of previously mined deposits. On the Westland and Otago Goldfields alluvial and fluvioglacial gravel placers, mainly representing lateral and depth extensions of previously worked ground, are being mined and prospected. Gold production in 1984 was exclusively from these deposits, and the development of mobile concentration plants has resulted in a great increase in mining activity. Mineralised zones adjacent to previously mined lodes in the Hauraki Goldfield, Reefton Goldfield, and at Macraes Flat (Otago Goldfield) are being intensively explored. At Waihi (Hauraki), an open-pittable resource of about 10 million tonnes of ore has recently been delineated. Some new deposit types and little explored environments are also receiving attention. They include: gold-sulphide quartz veins hosted in an alkaline granite dike in west Nelson; hot spring type gold deposits in fossil geothermal (epithermal) systems of Northland, the Hauraki Goldfield and the Taupo Volcanic Zone; and marine placers off the West Coast where an area of auriferous gravels has been outlined near Hokitika. There is potential in known deposits and prospects currently being evaluated for a large increase in gold production by the early 1990s.

Jan 1, 1986

By Lowell J. D

This paper is an outgrowth of a continuing compilation of the geology of Chilean ore deposits by Carlos Ruiz who was the author in 1965 of Geologia y Yacimientos Metaliferos de Chile which was the definitive compilation of the ore deposits of Chile. A new version was written by him in 1988, with the co-operation of Federico Peebles L, published in Geologia, Distribucion y Genesis de los Yacimientos Metaliferos Chilenos. Over the past eight years J David Lowell studied the geology of the Chilean mineral belts in connection with planning mineral exploration for copper and gold.

Jan 1, 1990

The New Guinea Mobile Belt is the northern zone of the Melanesian Orogeny (Dow and Sukamto, 1984), which consists of a complex zone ofupthrusted and accreted, regionally metamorphosed geosynclinal sediments and volcanics of Mesozoic to Eocene age and the overlying sediments. On the northern margin of this accreted terrane, formed an Eocene to Middle Miocene island arc. The North New Guinea Basin formed during the Upper Oligocene on the accreted margin. The depositional history of this basin is complicated by major crustal movements during the Upper Miocene to Holocene. During the Middle to Upper Miocene two magmatic arcs were emplaced. The northern magmatic arc is in part, spatically and genetically related to the Eocene to Middle Miocene island arc. The Maramuni-Utawa Magmatic Arc (southern) is a result of the Oligocene accretion and regional metamorphism. Coincident witt these magmatic arcs are belts of mineralization containing porphyry Cu-Au, epithermal/hydrothermal Au, Ag + Cu-Pb-Zn, exhalative Cu-Pb-Zn + Ag-Au, lateritic Ni-Cr-Co + PGE and alluvial Au, PGE, Cr occurrences and deposits. An intergrated tectonic model is presented for these and other data for the northern zone of the Melanesian Orogeny.

Jan 1, 1990

By Schofield D, Denby B, Stout F, Moli A

This paper documents the development of a user-friendly computational program, which has been constructed to assist the mine ventilation engineer in the optimal design and operation of methane drainage ranges. In the past, many computer tools for ventilation engineers led to the development of `research systems'. These computer systems, although developed with the needs of the industry in mind were due to a combination of inexperienced programming methods and the availability of suitable user interface software not easily accessible to the practising engineer. Recent developments in computer hardware and software (particularly windows based graphical user interfaces) mean that engineers no longer need to dedicate large amounts of valuable time to become familiar with often complex items of software. The authors of this paper intend to demonstrate a practical system which successfully integrates complex mathematical models, an easy to use interface and knowledge based techniques. The graphical interface guides the user to draw on the screen a mimic diagram representation of the methane drainage network. The user is prompted, during the construction of the drawing, to input the information and data required by the calculation and knowledge based procedures. The computer program then calculates all of the flows, purities and pressures throughout the network. Given reliable measured data from an existing range a comparative analysis can be performed between the predicted and measured network flow data. A knowledge-based system may utilise this analysis to either update the operational status of the network or suggest either a reasoned maintenance or remedial strategy to improve the performance of the drainage system. The development of the OMEN project has been carried out at the request of the Midlands Group, British Coal Corporation, Edwinstowe. The system is about to be field tested at a number of mines. It is hoped that when this paper is presented that the system will be used at both Group and mine level.

Jan 1, 1995

By Phipps P. J

The rate of precipitation of ferric iron as ammonium jarosite, NH4.Fe3(SO4)2(0H)6 from acidic solutions near 100¦C, was found to increase with weight of jarosite seed crystals, and with concentration of ammonium ion, but to decrease with increasing acidity. The particle size of the product crystals was larger at low sulphate concentrations and at high ammonium concentrations. Particles appeared to be agglomerates, with diameters ranging from 0.5 up to 25 um, and composed of individual crystals of diameters ranging from 2 um apparently down to 0.1 um or Lass

Jan 1, 1977

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By Koppe J. C

This paper describes the methodology developed to establish a sequentia mining plan applied to a coal mine, using computers. Firstly, isocontou. maps were generated from the drill holes and outcrop description information, representing the thickness and depth of the rock formation: present in the mine site. The procedure relies on the repeated application of the cross validation techniques, until the standard deviation of thi estimation is reduced to a minimum.From this map the coal reserves of the two coal seams, the overburdet (separated in hard and soft material) and the interburden were calculated After that, the maps were transferred in digital files to AutoCAI software, where different mining plan simulations were performed. 7b ore evaluation in each case was done automatically, including tonnages volumes and stripping relations. The final mine configuration consider the economic aspects of the operation.

Jan 1, 1993

The difficulty in creating and obtaining a competitive edge in the mineral industry is rapidly increasing. The Kiruna Iron Ore Mine in the far north of Sweden is currently thriving on the world market through firm managerial strategy. LKAB believes in upgrading its raw material to produce a high quality iron ore product for sale to steelworks throughout the world. It is vital that this product is also of uniform quality and quantity to provide quality assurance to customers. The first link in meeting these product requirements starts in the underground workings. Mining methods and operations are of large-scale. Automation and continuous production streamline operations and reduce operating costs. These factors have built Kiruna Iron Ore Mine into the world's biggest, most modern, underground iron ore mine. To remain competitive on the world market, LKAB relies heavily on research and development. The mine is currently in a phase of upgrading its operations. A 25-tonne Toro electric loader is being tested to improve the rate of output of ore from the mine. Long hole drills are being improved to increase accuracy and efficiency. An electronic detonating system will improve detonator delay precision. Projects are underway to better understand ore flow mechanisms from a caving orebody. Benefits include improved ore recovery along with better rock quality control at the caving front. The continued updating of mining operations at Kiruna will enable LKAB to continue to maintain its competitive advantage on the world market in the production of high quality iron ore products.

Jan 1, 1997

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

Statistics show that despite a low lost-time accident rate there is a high fatality rate from falls of ground in pillar extraction work. Investigation of accidents indicates that in many cases the planned ex- traction cycle has been ignored. Better training, supervision, and personnel protection and where possible changed systems are suggested as a means of improving safety and achieving better Results.

Jan 1, 1974

By Boland J

Prediction of rock cuttability by various excavation machines such as tunnel boring machines, road headers, rippers, picks, roller disc cutters, excavators, etc is of major concern to both civil and mining engineers and rock mechanics. In principle, the design of a rock cutting tool is based on achieving maximum excavation with minimum input energy, minimum applied force, minimum equipment weight and volume and, more importantly, minimum tool wear. When a rock material is indented by the force of a cutting tool and then unloaded several material zones form underneath and around the tool. As the tool moves into the rock the volume of its associated rock cavity (ie volume of displaced rock) expands and depending on the indenter's shape various phenomena may occur. Immediately beneath the tool a small zone in which the stress state is more or less hydrostatic, is formed which is underlain by an inelastic, or damaged, material zone. Both size and shape of this damaged zone control the magnitude of the indentation force and the chip formation mechanism during unloading. The rock is unable to store the whole strain energy induced by the tool and consequently the extra energy is expended either in forming new fracture surfaces and/or in plastic deformation in the damaged zone. Therefore, it is not surprising to see that both perfect-elastic and rigid-plastic constitutive models are not generally suitable for modelling indentation of rocks. In contrast elastoplastic constitutive models are more appropriate as they can include both elastic and plastic deformations (Kral et al, 1993). Elastic solutions for several half-space indentation problems can be found in most text books on elasticity and in particular in Timoshenko and Goodier (1951), Sneddon, (1951), Poulos and Davis (1974) and Johnson (1985a). If a failure criterion, eg the Mohr-Coulomb failure criterion, is applied to delimit elastic solutions for indentation problems, a lower bound limit of the applied indentation force (for a given indentation depth) can be estimated. It may be noted that elastic analyses, without any delimiting failure criteria, normally overestimate the indentation force. Plastic solutions for a few indentation problems may be found in Hill (1950), Johnson, (1985a) and Alehossein et al (1992). When analysing the behaviour of indented rocks the choice of an appropriate constitutive model describing effectively the behaviour of the rock at various stages and phases during indentation is a challenging issue. Several questions need to be answered before starting an effective analysis. The first question is of course: Which one of these is more appropriate for modelling zones underneath and around a cutter, elasticity or plasticity theory, continuum damage mechanics or fracture mechanics, and what is the bridging link between these various theories? Which mode is more dominant in fracturing rock, tensile or shear mode? What governs the mechanism of chip formation? What is the function, shape and the behaviour of the pulverised zone that forms just underneath a cutter? Is the hydrostatic stress state assumption reasonable for this zone? How does the rock change during the absorption and dissipation of the input energy and how does the indentation energy vary with rock type and depth of penetration? How can we model the damaged zone under the indenter? Furthermore does a plastic material form beneath the pulverised zone? When and how do radial and ring cracks form around and under an indenter?

Jan 1, 1995

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993