Search Documents

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By Rowe P, Rogers D, Warren M

Pressure cyanidation of the minus 10 micron slimes fraction of the Fimiston flotation concentrates for the recovery of gold values has been evaluated as an alternative processing route to the roasting and atmospheric cyanide leaching of the calcine. Laboratory and pilot trials have demonstrated that gold extractions of greater than 94 per cent can be achieved at cyanide consumptions of 12-24 kg/t and oxygen consumptions of 0.1-0.3 Nm3/t with total pressures of 1000-2000 kPa. Economic and operational assessment of several reactor configurations suggests autoclaves may be preferred over pipe reactors at treatment rates of 10 t concentrate/h.

Jan 1, 1996

By R Frew, E Wong, G Ferguson

The Chang Jiang Tunnel and Bridge Project, when completed, will provide a fixed link between ShanghaiÆs rapidly developing Pudong District and Chong Ming Island, situated in the Yangtze River delta. The link includes 7.5 km of bored tunnel from the Pudong to the intermediate Changxing Island from where the link comprises viaduct and a cable stayed bridge. The bored section comprises twin 13.7 m internal diameter segmentally lined three-lane highway tunnels. At its deepest point the tunnel will be 55 m below the river. Cross passages will link the two bores for passenger evacuation. Tunnel boring commenced in October 2006 and is scheduled for completion in mid-2009. The paper describes the key features of the design and construction of the bored tunnel by two 14.53 m diameter slurry TBMs and eight cross passages using ground freezing techniques in alluvial sediments. A decision to include light rail below the road deck was taken after the completion of the detailed design. This posed a number of design challenges including passenger evacuation to the road deck, and the redesign of the low point sumps. The various options considered are discussed together with those adopted for construction.

Jan 1, 2008

By K White, R Hardie, J Merritt, B Kirsch, R Lucas

Constructed stream diversions are a common element of mine sites across Australia. A review of constructed stream diversion performance in the Bowen Basin funded by the Australian Coal Association Research Program (ACARP) in 1999 found over 80 per cent of constructed stream diversions failed to meet regulator and operator expectations. Since that time, improvements have been made in the assessment, design, monitoring and management of constructed stream diversions. Fundamental to these improvements has been the development of a better understanding of the regional stream systems and efforts to replicate the natural stream processes in the function and operation of constructed stream diversions.This paper discusses the history of constructed stream diversions through the Bowen Basin in central Queensland recorded in the outcomes of a series of ACARP funded research projects. Further, the paper reports on the outcomes of a current ACARP funded project that has reviewed the success or otherwise of constructed stream diversions in the region. The assessment has compared the performance of diversions that have been designed to replicate and provide for ongoing stream geomorphic processes with those diversions that were designed and built prior to the development of these design improvements. Based on these investigations we have identified design and construction successes and issues requiring further research and management attention.CITATION:White, K, Lucas, R, Hardie, R, Merritt, J and Kirsch, B, 2013. Challenges and opportunities for constructed stream diversions in the Bowen Basin, Central Queensland, in Proceedings Water in Mining 2013 , pp 73-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By J Hadjigeorgiou

Underground mines often rely on ore pass systems to ensure the transport of ore and waste. Consequently, it is important to ensure the smooth operation of such systems. Ore pass degradation that may require rehabilitation results in production delays and high operational costs. The occurrence of hang-ups within an ore pass also leads to disruption of ore production. There are important safety concerns when worker intervention is necessary to re-establish material flow in the ore pass. In order to facilitate the design of ore pass systems, mining operations often rely on past experience, or semi empirical guidelines. This paper describes recent efforts to establish a comprehensive database on current practices; encountered operational problems and solutions in ore pass design in Quebec underground mines.

Jan 1, 2003

By Chia A. H

This paper presents an overview of the development and operation of the PT Adaro Indonesia coal mining project. This operation is an initial two million tonne per annum mine, located in South Kalimantan, Indonesia.The paper places emphasis on some of the more unique infrastructure development and operational challenges that exist in such a remote location environment.A brief summary is also given of the Indonesian coal industry, its direction and position as a significant coal producing competitor for Australia.

Jan 1, 1992

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By Toguri JM

A solid electrolyte technique has been used to measure the activity of cobalt in liquid cobalt-gold alloys containing between 0.085 and 0.50 mole fraction of cobalt, and for temperatures from just above the liquidus to around 1550 K. The system exhibits positive deviation from ideality, both in the activities of cobalt and gold, and in the enthalpy and excess entropy of mixing. The results agree with previous measurements using a Knudsen cell - mass spectrometer technique, but differ from those reported for a gas equilibration method. The data have been used to calculate the activity coefficient of cobalt oxide in silica saturated iron silicate slags and to express the solubility of cobalt in such slags as a function of cobalt activity and oxygen pressure.

Jan 1, 1984

By D Flint, O Rindriatmoko

PT FreeportÆs Deep Ore Zone (DOZ) Mine is the latest block cave mine within the East Ertsberg Skarn System (EESS).Issues with undercutting and stress concentrations at the extraction level were experienced, leading to reduced pillar strength.The extraction level-related issues became more pronounced, leading to local panel drift collapse, in an area that was over 100 per cent extraction. A review of ground conditions, panel collapse descriptions, and factors contributing to panel collapse are presented in this paper.

Jan 1, 2005

The Auscoke project has reached-a stage where a pilot plant nominally able to produce 100 t.p.d. of coked briquettes is being brought on stream during Nov. 1971 . The targets for this stage of the project are to establish the technological and economic value of Auscoke for the iron blast furnace, and to verify the commercial feasibility of large scale plants. The project originated at the B.H.P. Central Research Laboratories (C.R.L.) and work to date has shown that using a two stage contin- uous process, strong large coke can be produced at good productivities from medium or low volatile poorly caking coals. General features of the pilot plant and processing are discussed.

Jan 1, 1972

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005

By Armstrong M

Two methods of Monte-Carlo simulations, one suggested by Matheron (1972) and the other by Rudenno (1983), have been tested for simulating coal deposits. To do this 2160 values of ash percentages were simulated using 60 known data points in a two dimensional grid, 20 m x 40 m. 1L is found that while both methods conserve the mean of the known distribution in the results of the simulations, only the first method reproduces the spatial covariance (i.e. the variogram), of the experimental data. The results show that for simulation of regionalized variables only the first method tested yields the desired results.

Jan 1, 1985

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

The constraints in university courses are lack of hours, high cost of scientific equipment, and poor availability of suitably experienced staff. These have forced the balance away from practical work and towards more theory. Labelling of individuals as either practical, or academic, does not help the inter- change of staff between industry and univer- sities that is necessary to balance idealism and realism. Practical men who do return to universities may lose seniority and find that industry is reluctant to have them back. Academics who specialise too long may concentrate on their research to the exclusion of basic material. It is difficult to operate pilot scale plants in universities because of lack of time, and obsolescent equipment. Small grants from industry might enable tests to be run in research laboratories such as at C.S.I.R.O.. Within universities there may be a need for greater interchange of students among depart- ments, aided by the absence of weighted student unit measurements, as suggested by Aus.I.M.M. and A.M.I.C.

Jan 1, 1984

By J Nell, J Petersen, X C. Goso

The feasibility of increasing the deportment of titanium species and the stability of the pseudobrookite solid solution (M3O5) in a titaniferous slag was investigated, to facilitate the valourisation of titaniferous slags. Thermochemical simulations using FactSage™ software, ver 8.3 (by Thermofact/CRTC and GTT-Technologies), and equilibration-quench experiments were conducted using an appropriate synthetic titaniferous slag composition in an oxygen partial pressure (pO2) ranging from air to 10-16 atm under non-isothermal conditions. The temperature-pressure phase stability diagram for the synthetic slag containing 37.19 per cent TiO2, 19.69 per cent SiO2, 13.12 per cent Al2O3, 16.00 per cent CaO and 14.00 per cent MgO showed that the spinel solid solution (M3O4) was the primary phase until a pO2 of 10-10.5 atm, thereafter M3O5 was the primary phase until a pO2 10-13.2 atm. M3O4 again was the primary phase between a pO2 10-13.2 and 10-16 atm. The changeover of the primary phase coincided with an increase in the liquidus surface. When cooling the slag in a pO2 of 10-16 atm, M3O5 crystallised as a ternary phase that showed a rapid increase in mass while that of the primary M3O4 phase decreased and that of the secondary perovskite (CaTiO3) phase increased at a slower rate. At 1300°C under sub-liquidus conditions, the contents of M3O5, M3O4 and CaTiO3 were about 20 per cent, 15 per cent, and 11 per cent, respectively. Experimental results showed that the Ti3+/Ti4+ mass ratio in the M3O5 phase, ie a measure of the reduction of titanium species, is not considerably sensitive to equilibration temperature in the reviewed range. Slow cooling and minimum/no oxidation during cooling of titaniferous slag would increase the deportment of titanium species to, and the growth and stability of the M3O5 phase.

Jun 19, 2024

By Miller JD, Ye Y

The Air-Sparged Hydrocyclone (ASH) has been developed for the fast and efficient flotation of fine mineral particles in a centrifugal field during the past decade at the University of Utah. Over the years, the air-sparged hydrocyclone unit has shown promising potential for the flotation of copper porphyry ore, low-grade placer gold and auriferous pyrite ores, various industrial minerals, and fine coal cleaning. Many fundamental studies including the X-ray computed tomography (CT) analysis have been carried out in order to understand the multiphase fluid flow phenomena associated with ASH flotation. With data available from these studies, it is now possible to construct more accurate ASH flotation models for different applications in order to analyse the behaviour of the system and to optimise design and operating variables. The ASH flotation model developed in this paper is based on the data given in `Air-Sparged Hydrocyclone/Advanced Froth Flotation Fine Coal Cleaning', Final Report, DOE Contract No DE-AC-88PC88853, submitted by Pennsylvania Electric Company (PENELEC), December 1989. Data from several hundred experiments with the two-inch ASH-2C air-sparged hydrocyclone (capacity 0.1 - 0.3 tph dry coal) are available from the report and have been used for this analysis. In the past, a preliminary model based on limited data had been developed. The current study, however, emphasises the global behaviour of the ASH system by utilising almost all the data from the report for the purpose of scale-up and industrial application. There are two parts in the current modeling and analysis effort for ASH flotation of fine coal. The first part is the modeling/analysis of dimensionless ratio of overflow opening area to underflow opening area, A*, and the dimensionless ratio of air flowrate to slurry flowrate, Q . The second part involves the modelling/analysis of all other variables in the system and an expert system for operation and control is introduced.

Jan 1, 1993

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000