Search Documents

Radioisotope x-ray methods for the on-stream determination of copper, lead, and zinc in mineral product slurries were developed, and were successfully tested at the plant of Cobar Mines Pty. Ltd.The tests were made in three stages. Measurements to determine the precision of analysis were made initially on briquettes of the mineral products. The effect of slurry solids content variations was then determined by measurements on the mineral products in a recirculating slurry loop. The radioisotope analyser was finally tested in a series of on-stream measurements in the plant.Copper, lead, and zinc in flotation feed and in copper concentrate were determined to a precision ranging between 1·4 and 15 per cent of the mean element concentration in the slurry solids. These precisions are within limits required for plant control purposes at Cobar.

Jan 1, 1971

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

The importance of reducing the moisture content of fine coal, the nature of the retained water, and the means of its removal are discussed. A statistical technique, using a balanced block design, was used to isolate the significant factors determining water content of a coal filter cake. The most significant factor was particle size distribution. A simplex evolutionary operation (evop) was used to determine the optimal quantities of additives required to produce the lowest moisture content for a selected coal size. For this optimum condition (18·6 Ib H20 per lOO Ib dry coal), additions of 0·045 Ib magnesium ion, 0·0026 lb Separan AP30, and 0·098 Ib Aerosol OT, per lOO Ib dry coal were required. The work illustrated the uses of a statistical evop technique for the determination of optimal conditions in industrial research projects.

Jan 1, 1970

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

The suitability of char from Yallourn brown coal as a filler for carbon electrodes used in the aluminium smelting industry has been assessed on the basis of the specifications usually laid down by electrode manufacturers for petroleum coke fillers. The purity specifications can be met by a simple acid leaching of the coal before carbonization. The true density of char produced at 1200°C is within 5 per cent of the specification figure, but the bulk density of char obtained from as-mined coal is only half that specified for petroleum coke.Although this can be increased to three-quarters of the specified figure by briquetting the coal before carbonization, further increases would be very difficult to achieve, as the remaining shortfall in density is due to an extensive microporosity developed in the particles of char during carbonization.

Jan 1, 1970

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

By R WOODS

The interaction of, flotation collectors with sulphide mmerals takes place at the solid-solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulphides is an electrochemical process, xanthates being electro-oxidized to chemisorbed xanthate and dixanthogen.The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidized xanthate species. The action of reagents which can activate or depress the flotation of sulphides is discussed briefly.

Jan 1, 1972

At the present time this plant is treating by direct cyanidation 1,000 tons of ore from Open Cut mining and dumps, and 1,200 tons of current flotation tailing obtained from the Sulphide Mill, per day.The following table shows the average analysis of the two feed products (see Table 1):Precipitation Process.-The pregnant solution obtained by the cyanidation of the above has the following general analysis:-Gold 0·600 dwt. per tonTotal Cyanide 0·050 %Free Cyanide 0·045 %Calcium Oxide 0·015 %KCNS 0·060 %Na2S20S 0·140 %CaS04 0·200 %Cu 0·050 %Zn 0·004 0/0K4Fe (CN) 6 NilThis solution, after standard clarification, is precipitated by means of zinc dust and a soluble lead salt.

Jan 1, 1939

This method determines tellurium at concentrations down to 0·01 p.p.m., with geochemical accuracy. Tellurium is volatilized from the rock at 800°C in the presence of sulphur from decomposing pyrite, condensed, dissolved, and finally determined by atomic absorption in a long tube burner. The distribution of Te is shown near some gold lodes at Kalgoorlie. Lastly, a method of synthesizing Te-free pyrite from sulphur and ferrous sulphate is described.

Jan 1, 1969

Alkaline leaching with sodium carbonate solution adjusted to pH 9·5 to 10·0 preferentially dissolves thorium from a mixture of rare earth and thorium hydroxides. Rare earth sodium carbonates form in the alkaline leaching stage.These are converted to rare earth oxides for use as optical and ophthalmic polishing agents. Quadrivalent cerium is extracted under similar alkaline leaching conditions.INTRODUCTIONAustralia has made significant contributions to mineral chemistry and mineral dressing. As often happens with an industrially immature country, research investigations often outstrip the ability or desire of commerce to exploit them. It is wrong to think exclusively in terms of export of raw materials. Imagination assists in developing world trends. The chemical utilization of mineral sands has interested a group of investigators, chiefly at the Commonwealth Scientific and Industrial Research Organization (C.S.I.R.O.) and, more recently, in the mining industry itself. From an international point of view the highlight of this work was Newnham's (1960) process for the separation of hafnium from zirconium. Earlier work at C.S.I.R.O. investigated the chlorination of rutile, zircon, and monazite. Assuming that titanium tetrachloride would be available in large quantities in the post war years, extensive work was done by Kraitzer, McTaggart, and Winter (1948) on organic compounds of titanium. This work led to the development of heat resistant paints, plastic compositions, and improved organic protective coatings that predated overseas work by up to seven years. (Post, Shiihara and Schwartz, 1961; Anon, 1955). Contributions were made to the production of refractory hard metals (Kraitzer, 1949; Kraitzer and Newnham, 1956). Pilkington and Wylie (1947) and Urie (1947) investigated the production of rare earths from monazite by an acid process.

Jan 1, 1963

By Paterson R. G, Compston W

The Mine granite at the Ardlethan tinfield is dated by Rb-Sr on a muscovite concentrate at not less than 417 ± 2.5 Ma (2s), consistent with the intrusion of this granitic body into folded Late Ordovician sediments. A combination of Rb-Sr and K-Ar evidence suggests a slightly younger age, 41O ± 2.5 Ma, both for the neighbouring Ardlethan Granite and for the hydrothermal alteration of the Mine granite, with which the tin is associated.On this basis, the somewhat high 206Pb/204Pb of two galena samples from within the hydrothermal alteration zone is best explained by an increase in U/Pb of order 10 per cent during a geochemical event in the Late Precambrian, in the rocks which eventually yielded the Pb to the mineralising fluid. This earlier event probably increased Th/U in these rocks as well, by as much as 5 per cent. If these reconstructions are valid, the lower-than-average U/Pb implied for the original Precambrian source rock bespeaks a mantle component of marginally greater proportion than for "average orogene".

Jan 1, 1982

Silica reacts with cryolite at 1010°C in two stages. The first stage is the formation of a sodium aluminosilicate of composition consistent with the mineral jadeite (Na20.AI20s.4Si02). The formation proceeds by atleast two different reactions. Formation of alumina or an aluminosilicate proceeds to its limiting value in the first 30 min while the formation of jadeite proceeds at a steady rate until quantitative conversion is achieved after 150 min. The net overall reaction can be expressed by the equation 6 Si02+2 Na3AlF6? (Na20.AI20s.4Si02) +2 SiF4 +4NaF.The second stage involves a slow reaction that proceeds with the evolution of a little SiF4, The net result is the formation of sodium aluminosilicates that are soluble in 30 per cent AlCIs-HCI solutions. While this could be explained by disproportionation of jadeite to form albite (Na20.Al203.6Si02) and nepheline (Na20. AI203.2Si02), it is more likely that it is due to further but limited reaction between the oxides and fiuoroaluminates.

Jan 1, 1972

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty. Ltd. differ supstantially in their characteristics. Knpwledge of performance not only enables comparison and promotes better control, but also provides the means for predicting results.Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep). Results for Baum jigs, a Chance cone, heavy medium cyclones, and water washing cyclones were examined. The efficiency factors derived from the probable error were applied to the float and sink analysis, mathematically simulating operating conditions. This method was applied to the Balgownie seam.The Balgownie seam lies between the Bulli and Wongawilli seams in the coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits rather difficult washability characteristics, due to a comparatively high middlings content. These properties and the relatively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique.Applications of result forecasting are listed.

Jan 1, 1971

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Turker L

The leaching of Tellness (Norway) ilmenite concentrate in hydrochloric acid and mixed aqueous HCl-alcohol solutions at boiling temperatures was investigated. It was found that the alcohols methanol, ethanol and ethylene glycol all substantially increased the leach rate and in the case of methanol and ethanol this was achieved at lower boiling temperatures compared with aqueous HC.

Jan 1, 1986

The Main Seam occurs in two 'pods', termed North and South, separated by an east-west oriented 'want' zone (most probably a palaeo-channel). The seam on either side of the 'want' area reaches thicknesses of over 30 metres but the North Main Seam adjacent to the 'want' zone has been split into multiple seams of 10 to 15 m thickness. Rock types in the inter-burden of this area are characterised by inter-bedded sandstones and carbonaceous mudstones varying in thickness from 0.5 to 5 m. In the South Main Seam, an area of un-split coal exists and is characterised by few inorganic partings. Overburden in this area varies geographically from relatively thick mudstones in the south and east part of the coal deposit to inter-bedded sandstones and carbonaceous mudstones adjacent to the 'want' area. The sandstone/mudstone overburden probably represents a splay or splay-channel complex emanating from the larger 'want' area palaeo-channel. Modelling lithological variability is of use because it is one of the factors used in predicting cavability and roof support system design. The coal in both the north and south deposits were found to exhibit highly predictable quality and breakage parameters in relation to the coal geometry. Although ash yield and sulphur are mostly low and not variable, volatile matter and thus fixed carbon, varied in relation to seam thickness. In general, volatile matter (dat) decreased and moisture increased with decreasing seam thickness whereas moisture increased with decreasing seam thickness. In addition to these parameters it was found that the energy needed to crush the coal was lowest at the top and bottom of the seam and, on a whole seam basis, decreased with seam thickness. All of these parameters were found to vary in relation to the vitrain band content of the coal which itself was controlled by seam geometry. These parameters can therefore be modelled and inputted into mining plans and quality control operations.

Jan 1, 1996

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35°C to 90°C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0·75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975