Search Documents

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By M. C. Flemings, P. J. Ahearn

Dendvite morphology of unidirectionally solidified Sn-12 pct Bi alloy was determined with the aid of X-ray and macroetch techniques. Columnar growth direction (growth direction of primary arms) in this alloy is [110]; secondary arms grow in the [lii], [111), and [112] directions. Interstices between [112] dendrite arms fill in during early stages of solidification so that well-defined (110) planes are seen in the final structure (parallel to the heat-flozo direction). Similarly, interslices betweex the [111] secondary arrlls fill in to form (112) planes, and interstices between [1111 ] arms fill in to form (112) planes. DENDRITE morphology in alloys is conveniently studied in unidirectionally solidified castings. In this type of solidification, heat is extracted from a single chill surface of the casting while other surfaces are insulated. Solidification progresses from the chill and results in cast grains that are columnar with the long axis of the grain perpendicular to the chill. Dendrite morphology is conveniently studied by examination of etched surfaces parallel and perpendicular to the chill, as previously described.'" Experimental studies on the growth direction for tin are in general agreement. The major growth direction is [110]:-' although this is altered somewhat by supercooling. In one study, tin dendrites pulled from a supercooled melt had a growth orientation 12 deg away from the [110] direction toward the [002] direction.' This orientation could be changed back to the [110] or close to the [110] direction by changing the tempera- ture gradient in the melt. In a study using autoradio-graphic techniques, (111) directions were shown to be directions of preferred growth in addition to the [110) direction.7 PROCEDURE The samples employed in this study were cut from 12 pct Bi-88 pct Sn castings, 1.5 in. in diam and 3.5 in. tall. The casting procedure consisted of heating the charge to 390°C and then pouring the molten alloy directly into a gypsum sleeve mounted on a massive copper chill. Specimens were cut from the ingot, mounted, polished, and etched with Taffs reagent [FeC13 .6H2O, 2 g; HC1, 5 cu cm;H20, 30 cu cm; CzHaOH (95 pct), 60 cu cm].' The dendritic pattern was clearly visible after etching. Photomicrographs at about 8 and 35 times were taken on surfaces parallel and perpendicular to the chill. Laue back-reflection patterns were obtained from three different columnar grains in a singIe polished face 2 in. from the chill. The cut face was polished and positioned in the beam of a Laue camera, so that diffraction occurred from a single dendritic grain. The resulting diffraction pattern was interpreted to determine crystal log raphic orientation in relation to the heat-flow direction and in relation to microstruc-ture of the given grain. RESULTS Fig. 1 shows a horizontal and vertical section of the columnar structure, at low magnification. Light regions are rich in tin, and darker regions tin-poor; the primary phase is tin-rich a phase. The two sections shown were taken orthogonally from the same metallographic specimen. It is readily seen from Fig. 1 that the dendrites have

Jan 1, 1968

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By M. Muskat, R. D. Wyckoff

The general problem of the simultaneous movement of water and oil in a connected sand is of considerable practical interest from two points of view. First, there is the situation usually described as "edge-water encroachment." Here the water in the sands contiguous to and flanking the oil sand begins to enter the latter as the oil is removed and the reservoir pressure declines. The physical questions involved concern an understanding of the mechanism of the advance of the water and its control, so as to aid the oil recovery rather than to hinder it. In so far as the entry of the water into the oil sand means at least the partial replacement of the oil from the region of the encroachment by the advancing water, it is quite appropriate to consider this type of situation as one of natural water-flooding. For the present discussion, however, we are primarily interested in the problem of artificial flooding. Here the water is deliberately injected into the oil sand with the intention of displacing the oil and removing it through prearranged output wells. For the practical development of such a procedure rather large areas are included in the flooding program and the injection and output wells are arranged in regular patterns or networks, which are felt to be most favorable for a high oil recovery. Although remarkable success has already been obtained in such flooding programs, especially in the Bradford field of Pennsylvania, essentially by the application of the lessons of practical engineering experience, a more thorough physical analysis of the problem appeared to offer promise of leading to results of some interest and value. Another phase of the problem, which stimulated both the experimental and mathematical analysis, is that it is susceptible in large measure to empirical field tests. It, is in itself but an example and illustration of the general theory of the flow of dead (gas-free) liquids through porous media, in which the authors have been interested for the last several years. From the point of view of its applicability to actual petroleum technology problems, however, water-flooding is a particularly favorable

Jan 1, 1934

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum' of useful samples.

Jan 1, 1939

By Allan Clark

(San Francisco Meeting, September, 1915) IT is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper' read before the Institution of Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the' cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders.

Jan 7, 1915

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969

By Warnie Flint

According to statistics that have been compiled by the National Safety Council, U.S. Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. There isn't anyone who is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver isn't expecting a terrifying crash, the electrician isn't expected to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual. These are the victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed upon industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and the U.S. Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it doesn't. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons: 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group 3) Physical or mental condition.

Jan 1, 1973

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

By Richard F. Moe

INTEREST in developing White Pine, considered since 1942, was renewed by the Korean conflict and its shortage of domestic sources of copper. In view of this Morris F. La Croix, president of Copper Range Co. of Boston, and of its wholly owned subsidiary, White Pine Copper Co., worked an agreement out with Government officials. Essentially the contract called for a construction loan of $57,185,000 at 5 pct interest, with $13 million additional supplied by Copper Range. Defense Materials Procurement Agency contracted for 243,750 tons of copper from the first 275,000 tons produced, at a base price of 25.5& per lb, the contract to expire Dec. 31, 1961.

Jan 4, 1954

By T. Y. Yan

SUMMARY Laboratory high pressure column tests have shown that the presence of 1-20 ppm of aluminum ion effectively prevents permeability loss during uranium leaching with leachates containing sodium carbonate. If added after permeability loss has occurred, aluminum ion can restore the permeability to nearly its original value. No deleterious effect was observed on uranium leaching performance and the technique should be quite compatible with all field operations. INTRODUCTION The recovery of uranium values from underground deposits by in situ leaching or solution mining has become economically viable and competitive with conventional open pit or underground mining/milling systems (Merrit, 1971). In situ leaching processes are particularly suitable for small, low-grade deposits located in deep formations and dispersed in many thin layers. Many such ore bodies occur along a broad band of the Gulf Coastal Plain (Eargle et. al., 1971). The advantages of the in situ leaching processes have been reviewed (Anderson and Ritchi, 1968). In the in situ leaching process, a lixiviant containing the leaching chemicals is injected into the subterranean deposit and solubilizes uranium as it traverses the ore body. The pregnant lixiviant or leachate is produced from the production well and is then treated to recover the uranium. The resulting barren solution is made up with the leaching chemical to form lixiviant for re-injection. Upon completion of the leaching operation, the formation is contaminated with leaching chemicals and other species made soluble in the leaching operation and has to be treated to reduce the concentration of these contaminants in the ground water to levels acceptable to the regulatory agencies (Witlington and Taylor, 1978). Restoration is accomplished by injecting a restoration fluid, which could be the fresh water or water containing chemicals, into the formation. As it traverses the leached formation, the restoration fluid picks up the contaminants and is then produced at the production well. This produced water is either disposed or purified for recycle. In both phases of operation, formation permeability or well injectivity is one of the most important parameters which determines the viability of the in situ leaching process. Low formation permeability limits production rates, leading to uneconomical operations. The formation is said to be sensitive if there is a sharp loss of permeability on contact with water and other fluids. Many uranium bearing formations, for example, the Catahoula formation of the Texas Coastal Plain, contain significant amounts of clay minerals which are water sensitive. Serious permeability losses can occur when the pH and chemical composition of the lixiviant is significantly different from that of the formation water. Jones has investigated the influence of chemical composition of water on clay blocking of permeability (Jones, 1964) and Mungan studied permeability reduction through changes in pH and salinity of the water (Mungan, 1965). Various mechanisms of permeability damage have been proposed and reviewed (Jones, 1964; Mungan, 1965; Gray and Rex, 1966; and Veley, 1969). When large amounts of swelling clays are present, a significant fraction of the flow channels in the formation can be reduced due to swelling. However, in most cases, swelling need not be the main cause of permeability losses. Particle dispersion and migration or clay sliming can be more important causes for formation damage. Clay particles entrained in the moving fluids are carried downstream until they lodge in pore constrictions. As a result, microscopic filter cakes are formed by these obstructions, plugging the pores, effectively restricting fluid flow and reducing the formation permeability. Moore found that as little as 1-4 percent clays present in a fine grained sandstone could completely plug the formation if they are contacted by incompatible injected fluids (Moore, 1960). It has been found that injection of NaHC03/Na2CO3 lixiviant into formations with significant clay content often leads to loss of formation permeability and well injectivity. To alleviate this problem a change of the lixiviant composition to KHC03/K2CO3 has been proposed. At present, however, many in situ leaching operations employ NH4HC03/(NH4)2C03 mixtures as a source of carbonates. This approach has been successfully used in South Texas by Mobil, Intercontinental Energy, Wyoming Minerals and U.S. Steel, etc. The use of ammonium carbonates solutions, however, contaminates the formation and requires a time-consuming restoration operation. The other approach to reduce the permeability loss is to pretreat the sensitive formation with chemicals which prevent clay dispersion and migration. Such chemicals include hydroxy-aluminum (Reed, 1972 and Coppel et. al., 1973), hydrolyzable zirconium salts (Peters and Stout, 1977), hydrolyzable metal ions in general (Veley, 1969) and polyelectrolyte polymers (Anonymous). Still another approach, is to minimize the "shock" caused by sudden injection by gradually changing the chemical composition of the injected fluids from that of the formation water. THE APPROACH Since permeability loss can be an important factor limiting the efficiency and economic viability of the in situ leaching process, a study was initiated on

Jan 1, 1982

By Franz Wever

ACCORDING to Tammann,1 the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted-the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes in properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by lowing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By Mark Alling

INTRODUCTION A FEW years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 7, 1914

By F. N. Rhines

STUDIES upon the sintering of metal powders, in the solid state, have led to the proposal that the surface energy of the powder particles provides the driving force that causes points of contact between pairs of particles to grow into broad welds which isolate the residual vacant space into pores that tend to spheroidize and gradually to diminish in total volume.' Investigators differ with regard to the mechanism of the movement of the metal, under the influence of surface energy, to accomplish these changes. One school asserts that there is a mass movement of the metal, referred to as a "viscous flow," while the other school prefers to view the movement as a self diffusion process, wherein individual atoms are, transferred without disturbance of the basic pattern of the crystal lattice. Extensive experimental studies upon the sintering of copper, conducted recently by A. J. Shaler,2 have been in- terpreted by their author as support for the viscous flow mechanism of transport, the theory of which was developed originally by J. Frenkel.3 Duplicating a portion of this work with minor changes, G. C. Kuczynski4 is led to the alternate view, namely, that the initial stages of sintering, at least, proceed as a self-diffusion process. Both of these investigations were designed to deal with an isolated unit of sintering, i.e., with the shrinkage of a single pore, or with the growth of a single point weld. It remains to ascertain the behavior of a typical metal powder compact composed of a large number of particles of varying size and sintering to a body with a multiplicity of pores. The observation of density changes alone during sintering is not sufficient in such a case; it is essential to know how the internal geometry of the compact changes. This has been the object of the present investigation, the results of which are used to support the self-diffusion mechanism of sintering. The present studies consist in the measurement of the number of pores as a function of size and time at temperature during the sintering of a copper compact made from a commercial copper powder lightly pressed and sintered in several different atmospheres. A brief survey was made also of the change in shape of the pores, under the influence of the same variables. All of this was done by direct observation with the microscope. Densities were measured on the same sample. It is found that, while the compact is exhibiting an overall shrink-

Jan 1, 1951

By Charles H. Snow

The engineer has often to penetrate difficult or unknown regions. Mineral, irrigation, boundary and railway problems frequently necessitate journeys through, or long residence in, localities whence sustenance cannot be drawn. The selection and conveyance of provisions, outfit and implements thus become a matter of the first importance. Scientific skill, even of the highest order, is powerless unless supported by the proper appliances and foods. The advance of civilization favors the engineer, in that it is constantly enlarging his facilities and thus reducing his difficulties. Notwithstanding this fact, many are yet brought face to face with the problems considered in this paper. Distinction must be made between parties which are to be in constant or even occasional touch with a base of supplies, and those which will be for a long time dependent on their original outfit. Again, the requirements of a party on the march are different from those of a fixed camp. The district, season, cliinate, size and personnel of party also influence the character of the outfit. A party that is to be detached from its base of supplies for some time requires a greater variety of food than if it is to be gone for a short time. Much less in proportion need be taken where the journey is not long, so that privation is confined to a limited period. The ability to establish a fixed camp permits a larger outfit than would be possible if the camp mere to be moved from day to day. Transportation, climatic and other conditions are thus so varied that lists prepared for one work could hardly be applied to any other without some modification. Lists that have proved successful in some instances may, however, serve as bases to be added to, or otherwise altered, for the case in hand. The mistake usually made is in providing too large an outfit. Every emergency cannot be provided for; so that it is well to take, not what may be needed, but what cannot be spared.

Jan 1, 1900

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, H Pray, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941