Search Documents

By T. R. Lippard

PURE gypsum may be broken down into its constituents as follows: [ ] Standard specifications (ASTM Designation C22-25) state that a material shall not be considered gypsum if it contains less than 64.5 pct by weight of CaS042H2O. Anhydrite, the second calcium sulphate mineral found in nature, may be broken into its constituents as follows: [ ] PROPERTIES OF GYPSUM AND ANHYDRITE Pure gypsum is colorless to white but various impurities change its color to shades of gray, brown, red, or pink. It has a hardness of 2 in the Mohs scale and can be scratched with the fingernail. The specific gravity of pure gypsum is 2.3 to 2.4, so that rock gypsum, free from moisture, weighs about 145 lb per cu ft. Gypsum crystallizes in the monoclinic system in tabular crystals that exhibit good cleavage

Jan 1, 1949

Chairman James F. Kemp :—I call upon Prof. Albert Sau-veur to open the general discussion on the subject of sound steel ingots. Albert Sauveur, Cambridge, Mass.:—I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain Rome very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my views. I have always remembered my astonishment, not to say dismay, some twenty years ago, when I beheld for the first time a steel ingot, a rail steel ingot, that had been split open from top to bottom. There was the pipe! There was an enormous cavity extending from a short distance from the top to nearly one-third of the length of the ingot; and when I was told that manufacturers seldom discarded more than one-tenth of the total length of the ingot it became evident to me that a large proportion of piped, and therefore, defective, or at least weak and dangerous, rails were manufactured; in fact, probably one rail out of six, nearly 17 per cent., of dangerous rails.

Jan 1, 1914

By G. M. Gay, R. L. Perrine

This paper describes a method of numerical computation for three-dimensional, unstable, miscible displacement behavior useful for heterogeneous systems, as well as for more ideal conditions. In the method, flow equations are first linearized by a perturbation approach. The basic flow process is separated and a solution for its behavior readily obtained. The remaining problem of deviations from the basic flow caused by non-ideal conditions is then subjected to numerical analysis. Results obtained from use of the method are also presented. Although conditions assumed in the test cal-culations were severe, results show the type of dispersing flow expected and appear quite satisfactory. The method has eliminated or reduced in importance problems of oscillating values near steep fronts, excessive computer smoothing, etc. A unique advantage of the method is that the source of variations from ideal behavior can be observed. ,The one serious drawback results from the algebraic complexity of the perturbation approach, and the need for second-order terms to be retained in calculations of interest. Fewer array points are available and more computer time is required than would be desired. However, these difficulties are also experienced with other approaches to the solution of three-dimensional dispIacement problems. INTRODUCTION Prediction of behavior of the miscible displacement process within a porous medium for any system of engineering importance is plagued by a number of difficulties. With typical fluid properties the displacing fluid has the lower viscosity, and there is a natural tendency toward flow instability. The problem of predicting instability is compounded by the fact that every real system is heterogeneous. Permeability will vary from point to point — not entirely systematically, and yet not in a random fashion leading to a readily defined average. Furthermore, permeability is unlikely to be isotropic. These permeability properties, which are characteristic of any real porous medium, accentuate the effects of flow instability. Another factor to be considered is that flow dispersion accompanies the displacement process in a porous medium. Mechanistically, dispersion is due to the fact that flow between any two points in the medium follows multiple tortuous paths, each characterized by slightly different flow properties. The fact that the coefficient characterizing dispersive properties of the real medium JS a tensor with variable elements complicates matters. Further difficulties arise because the parabolic influence, while not negligible, is small. Thus, there is a tendency toward steep and uneven displacement fronts along which dispersion smoothing must be represented accurately. Yet frequently used numerical analysis schemes may tend toward either instability, oscillation or excessive smoothing, none of which gives the desired accurate picture of flow behavior. Thus, while many experimental and analytical studies of the process have been made, predictions of actual performance are still subject to considerable uncertainty and possible improvement. This paper reports on part of a study which attempts to develop improved methods for solution of the flow equations describing the miscible displacement process. Of necessity, the calculations were performed on a large digital computer. A three-dimensional system is represented, and the coefficients defining dispersion and permeability can be varied in a manner representative of a real system. Because the differential equations are nonlinear, a first step is to linearize them using a perturbation approach. Objective of this approach has been to separate the basic flow which would occur in an ideal system and for which predictions are readily made. Then the numerical analysis, which is necessarily complex, is directed toward solution of the perturbation equations. These equations state how the basic flow is modified

Jan 1, 1967

By D. H. Woodard, G. W. Geil, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

Paper withdrawn from publication September 8,1977, after book was printed. Pages 258.272 are therefore omitted.

Jan 1, 1977

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By John Griffen

OF the western European countries, only England has made any extensive use of equipment developed initially by the coal preparation industry of the United States. About 20 years ago, the Chance sand flotation process for cleaning coal was introduced in England, and it has had a fairly wide adoption, particularly in the South Wales coal fields. In recent years, particularly since 1946, a considerable number of Denver flotation cells have been installed throughout the English coal fields for the cleaning of slurry. Until the advent of the Denver cells, the flotation of coal slurries in Western Europe had been done largely with the Mineral Separations cell or its modifications. Kleinbentik of Dutch State Mines had developed a cylindrical cell used in Holland and occasionally in Belgium and France. In England, the establishment of the National Coal Board to control the planning and operation of all coal production has retarded somewhat modernization of properties. A considerable period of study was required before definite long-range plans could be formulated. It was soon recognized that stopgap measures were needed in many cases to bridge the period until final plans could be developed and consummated. One of the stopgap problems in coal preparation was providing plants of small and medium capacity that could be used for a few years at one site and yet could be moved economically to another site so as to reduce depreciation charges per year and per ton. Such plants are being installed but the most satisfactory answer probably has not yet been found. One such installation uses a Norton Baum jig to wash 6 in. to 0. The equipment is in a steel structure rather than in a reinforced concrete frame with brick curtain walls, which is the normal structure for permanent plants. Since England has between 700 and 800 preparation plants for an output of 200 million tons per year, one of the long-range objectives is a consolidation of mine output which will require fewer coal

Jan 1, 1952

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By E. M. Wise

THE practice of dentistry, particularly the construction of artificial dentures and "bridges," involves a unique and difficult application of the precious-metal alloys. Appliances used in the mouth are continuously exposed to corrosive agencies which can hardly be described as mild, and must remain free from tarnish and be substantially immune to corrosion. Limitations with respect to space and weight demand high physical properties, while complexity of form requires ease of working. The high corrosion resistance required necessitates the use of alloys of high precious metal content. The usual expedient of resorting to mechanical working to produce the requisite strength and stiffness cannot be utilized because of the frequency of annealing and soldering operations. To meet these difficult conditions manufacturers of dental goods were early led, unknowingly perhaps, to the production of precipitation-hardening or temperable alloys. The excellent properties of iridium-platinum may have suggested the addition of platinum metals to the conventional gold-silver-copper alloys to produce greater strength and hardness. It was found that such quarternary alloys retained their high physical properties after passing through the usual soldering process; i, e., heating to 7500 to 8000 C. and cooling naturally in the air. Later it was discovered that they could be softened and rendered more ductile by heating to the same temperature and quenching, in water. These early examples of precipitation hardening, for years the common knowledge, of dental practitioners and laboratory technicians, escaped the attention of the scientific world and discovery of the transformation which was responsible for this hardening was discovered by the Russian investigators of the system Au-Cu, Kurnakow, Schemtschushny and Zasedatelev,(1) § although the optimum conditions for securing good properties in aged alloys were not given attention.

Jan 1, 1932

By Douglas Bunting

In the anthracite fields of Pennsylvania, mine fires occur with more or less regularity and their existence is an ever-present hazard in coal mining. In all probability 90 per cent. of the mine fires can be ascribed directly or indirectly to the ordinary miner's open lamp. Other causes may be smoking, electrical installations, gas explosions, gas feeders, and the communication of fire to the outcrops from ash dumps, culm banks, timber and brush fires. Fires in pump rooms, engine rooms, and barns have been largely eliminated as a result of the Act of Assembly, approved June 15, 1911, which provides that all inside buildings, including engine rooms, pump rooms, barns, etc., shall be constructed of incombustible materials. Smoking of pipes, cigars, and cigarettes should be prohibited in the mines and too much care cannot be exercised in preventing fires by enforcing all rules designed for that purpose. Mine fires that involve underground fighting are invariably dangerous, and all fires, irrespective of the method pursued in extinguishing them, involve property loss and expense. Each fire generally presents a more or less original problem, dependent on the particular conditions. Generally mine fires may be divided into two classes: Those occurring in inaccessible workings and those occurring in accessible workings. The methods pursued in extinguishing or controlling mine fires are as follows: (I) direct attack, (2) smothering by sealing, (3) flushing with silt or other solids, (4) flooding with water, (5) cutting off, (6) surrounding with incombustible materials, (7) digging out by stripping from the surface. Most fires arc extinguished in their incipiency by direct attack and failure to extinguish by this method is due to late discovery, lack of water, and facilities for fighting, or improper procedure in the initial attack. Should the method first pursued be unsuccessful, careful consideration should be given in determining next the method to be adopted; then the work should be carried on as rapidly as possible and under the supervision of the most competent persons. Materials and supplies should be furnished without delay and in sufficient quantities for the work to be accomplished.

Jan 1, 1922

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By R. Maddin, N. Ujiiye

ALTHOUGH the cold-rolled texture for body-centered-cubic metals and alloys is well known (see, e.g., Barrett'), the pole figure representing the texture may be interpreted in two ways. It may be regarded as consisting of several ideal preferred orientations with an associated spread (a view which is shared among several investigators2), or it may be regarded as consisting of two sets of continuous preferred orientation also with an associated spread."." Recently, Chen and Maddin7 noted a stable (001) [loo] end orientation for molybdenum single crystals rolled at low rates of reduction provided the initial rolling. orientation" was close to the cube ori-

Jan 1, 1957

By Herbert D. Drechsler

Mining Finance-is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm". The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance.

Jan 1, 1978

By Charles W. Goodale

The ores of the Butte district present a variety of combinations, and their treatment by concentration is an interesting study. They may be classified in general as follows: 1. Copper-silver ores, which are produced by the mines of the Anaconda group, and by the Mountain View, Colusa, Silver Bow and Parrot. The high-grade ores from these properties are roasted and then smelted; but a large proportion of the output is low-grade and siliceous, and hence requires concentration. The copper-bearing minerals are chalcocite, bornite, enargite and chalcopyrite, in varying proportions in the different mines, the gangue, which breaks readily into grains, being quartz and feldspar. 2. Silver-copper ores, of which the Gagnon vein is the largest producer. The grade of the ores from this mine is such that nine-tenths of the output requires concentration. The silver- and copper-bearing minerals of this vein are massive wurtzite, sphalerite, bornite, chalcopyrite, pyrite, tetrahedrite, enargite, tennantite and galenite, with a quartz gangue associated with feldspar and small quantities of barite and fluorite. The gangue is very hard and not at all granular. 3. Silver-ores containing a small amount of gold, embracing the product of the Alice, Magna Charta and Moulton claims, on what is known as the Rainbow lode, and that of the Lexington, Blue Bird, Nettie, Burlington and other mines. The gangue is quartz, carrying pyrite, sphalerite, galenite, tetrahedrite and argentite, with manganese in the form of rhodochrosite and rhodonite. Good results on ores of this class cannot be obtained by concentration, because large percentages of the silver-bearing minerals are disseminated through the gangue in such minute grains that even the finest practicable crushing

Jan 1, 1897

The Duluth Engineers' Club was formally organized on the evening of Aug. 5, 1918, at a meeting .attended by over l00 members of the several engineering professions. W. G. Swart, a member of our Institute, was elected the first President of the Club. At the organization meeting, an opportunity was given, to Alfred D. Flinn, Secretary of the United Engineering Society, to outline the assistance that is being rendered to the Federal Government in the present contingency by members of the engineering profession. Membership in the Duluth Club is to be open to mining engineers on the iron ranges as well as to the residents of the city of Duluth.

Jan 10, 1918

By F. W. Newhall, L. N. Plein

During the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Brownsville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to thechairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corporation, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which arc presented in this paper. Acknowledgments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication. Geologic Conditions The shaft is at Merrittstown, which is about one mile northwest of Republic. The topography in the immediate vicinity of Merrittstown consists of rolling country dissected by the meanders of Dunlap Creek and its tributaries. The surface slopes of the hills are gentle and their average gradient is less than 6º. The area at the point where the study was made lies on a hillside sloping towards the southwest, the gradient, varying from 1º to 14º. Fig. 1 shows contour lines at 5-ft. intervals on

Jan 1, 1936

By L. N. Plein, F. W. Newhall

During the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Brownsville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to thechairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corporation, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which arc presented in this paper. Acknowledgments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication. Geologic Conditions The shaft is at Merrittstown, which is about one mile northwest of Republic. The topography in the immediate vicinity of Merrittstown consists of rolling country dissected by the meanders of Dunlap Creek and its tributaries. The surface slopes of the hills are gentle and their average gradient is less than 6º. The area at the point where the study was made lies on a hillside sloping towards the southwest, the gradient, varying from 1º to 14º. Fig. 1 shows contour lines at 5-ft. intervals on

Jan 1, 1936

By Charles C. Russell, Glenn C. South

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Glenn C. South, Charles C. Russell

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944