Search Documents

By W. H. Somerton

The effects of drilling variable on rotary drilling rates and efficiencies have been studied by a series of laboratory drilling tests. TWO-cone 1.25-in. diameter hits were used to drill vertically upwards into rock samples at corltrolled weights and rates of rotation. Shale, sandstone and specially prepared concrete samples were used in this study. Power input to the ririllirig systeln was measured and drilling chips collected for energy — .size reduction studies. Reasouably good correlations between drilling variables and rates of penetrotion were found. Qrrantities that are difficult to evaluate include rock strength parameters and the effects of bit wear. Effects of bit size and geormetry require further investigation. Analysis of the drilling chips confirmed the premise that, for rocks containing two or more mineral constituents of diflerent strengths, a greater amourrt of rock breakage occurs in the weaker constituent. Drilling conditions which required greater amounts of energy produced finer drilling chips. As bit tooth wear progressed, drilling chips became finer. Efficiency of rotary drilling as a rock breakage mechanism was extremely low. Comparison was made with theoretical energy requirements and with energy requirements for size reduction by comminution methods. INTRODUCTION Many technological developments and innovations have made possible the successful drilling of oil wells by the rotary method to depths exceeding 20,000 ft. Bigger, more powerful rigs, better steels, improved bit design and more careful control of the circulating system have all contributed to this success. Despite these advances comparatively little is known regarding the basic mechanism of rock breakage by the rotary drilling process. Future improvements and, in particular, reduction of drilling costs will undoubtedly require a clearer understanding of the variables controlling effectiveness and efficiency of rotary drilling. Rotary drilling is inherently an inefficient means of producing rock breakage. Loss of energy in transmission from the surface to the cutting mechanism may be large, thus limiting the total amount of energy which may be applied to rock breakage. Increased efficiency may be realized by improved energy transmission methods such as the turbodrill. Conversion of transmitted energy to rock breakage by use of rotating cutter teeth is likewise inefficient. Improvement of cutter efficiency has been obtained essentially by empirical means —changes in bit tooth size, shape and spacing, and tooth deletion to give clean bottom-hole patterns. The present work was undertaken to investigate the factors controlling rates of bit penetration under laboratory drilling conditions. Laboratory drilling apparatus is shown in Fig. 1. The effects of rock strength and bit wear on drilling rates were investigated. Drill cuttings were analyzed to determine the character of breakage and to compare this with other methods of producing rock breakage. VARIABLES INVOLVED IN ROTARY DRILLING Some of the variables controlling bit penetration rates can be studied conveniently by dimensional grouping. R/DN f(F/D2S) or

By C. E. Cannon, R. C. Craze

This paper discusses the results of a study of reservoir pressures in the Gulf Coast area of Texas and Louisiana, showing the general relation of the reservoir pressure to its subsea depth, as well as excessive reservoir pressures that have been encountered. The latter are particularly important in mud-control work, and the data show why it is necessary to use muds having a relatively high density in many of the deeper wells drilled in this area. Only a comparatively few of the wells drilled in the Gulf Coast that have encountered excessive pressures are discussed, but as far as is known those omitted fall within the range of pressure observed by the writers. Measurement of Pressures The following methods were used to determine the values of the original pressures: 1. Estimation of original pressure from subsequent pressure behavior of fields. This method is not precise, and was used only in a few of the older fields in which better methods of obtaining original pressures were not available. Only normal pressures were determined by this method. 2. Measurement of shut-in pressures soon after completion of the first producing well. With one exception, all pressures measured by this method were normal, this well having a pressure slightly higher than normal. 3. Measurements of pressure in connection with drill-stem tests. 4. Estimates from the maximum hydrostatic head of mud that failed to prevent flow from the high-pressure formations into the hole. This method is not exact, tending generally to indicate low pressures. Normal Pressures All pressure measurements available are plotted in Fig. 1, with original pressure at the water-oil contact as abscissa and subsea depth as ordinate. All producing fields fall close to the solid line, which passes through the origin and has a slope of 0.465 lb. per sq. in. per ft. By way of compari-

Jan 1, 1938

By George Beavers

FLASH roasting of iron concentrate is in the experimental stage at Copperhill. The problem is peculiar in that the iron concentrate is predominantly pyrrhotite; the ratio of that mineral to pyrite being 5 to 1. Results so far indicate that the heat, generated in roasting a material containing 52.0 per cent iron and 38.0 per cent sulfur, requires special handling and for this reason the installation costs per ton of roaster feed may be too great to compete with hearth roasting. Interesting features of flash roasting at Copperhill are: 1. The sulfur dioxide content of the roaster exit gas can be varied between wide limits. Eight per cent sulfur dioxide gas, with 1.30 per cent sulfur in the calcine, has been common practice and gas up to 13.0 per cent sulfur dioxide has been possible. 2. Temperatures of the exit gases are very high. When roasting 60 tons or more of iron concentrate per 24 hr. in a modified Wedge roaster, the temperature in the roaster rises to 2000° F. and the calcine is lowered to 0.20 per cent sulfur. If the entire roaster system could be constructed to withstand such temperatures, ideal roasting conditions would obtain as regards sulfur elimination and tonnage roasted.

Jan 1, 1934

By Luiz C. Correa da Silva, Robert F. Mehl

An experimental study of the movement of markers in the systems Cu/a-brass, Cu/Sna-solid solution, Cu/Ala-solid solution, Cu/Ni, Cu/Au, Ag/Au, employing many types of markers and a variety of temperatures. Marker movement is confirmed and undoubtedly associated with the manner in which atoms move during diffusion. EVERAL years ago Smigelskas and Kirkendall' •S reported measurements on the interdiffusion of copper and a-brass and on the movement of inert markers placed at the original join. These markers were observed to move toward the a-brass side of the join, and from this it was inferred that zinc diffuses in a-brass more rapidly than copper. Similar results were reported a little earlier for the diffusion of solvents into high polymer solids.' This has attracted much attention, particularly from those interested in the mechanism and the theory of diffusion: Seitz3 has employed it in supporting the vacancy theory of diffusion; from the data Darken4 has calculated separate diffusion coefficients for copper and zinc, developing a "phenomenological" theory of diffusion; and Bardeen5 has employed it in constructing a general theory, including therein the work of Seitz and Darken, as has Le Claire. These matters have recently been reconsidered in a sympo~ium.7 Some reason has existed for questioning the work of Smigelskas and Kirkendall.' Their technique consisted in electroplating copper on a-brass, upon the surface of which Mo-wires had been secured, and then diffusing, measuring the extent of diffusion along the normal to the join, and measuring the marker displacement in the same direction by a comparator determination of the distance between Mo-wires on opposite sides of the electroplated brass sample. It has been suspected that the copper plate might have been porous, and that the original interface might have been an imperfect join, both contributing to the transfer of the volatile zinc by vapor transfer;' it has also been questioned whether the marker movement might not in a measure be a property of the marker itself; etc. These legitimate questions require experimental answers; the present paper offers such answers. Moreover, Smigelskas and Kirkendall studied the effect only in the Cu-Zn system and at one temperature; the attention which the work of Smigelskas and Kirkendall has commanded recommends similar

Jan 1, 1952

By G. Purcell, S. C. Sun

The objective of the present study was to detennine the role played by double bonds in the flotation of a very pure mineral using 18-carbon unsaturated fatty acids as collectors. Streaming potential measurements were made on a plug of pure synthetic rutile in solutions of inorganic electrolytes and unsaturated 18-carbon fatty acid soaps. Experimental results from these tests are detailed in the paper. The collector effectiveness of oleic acid with one double bond, linoleic acid with two double bonds, and linolenic acid with three double bonds has been a matter of speculation for many years, and conflic- ting experimental evidence1-8 has not clarified the issue. The overall objective of the present study was to determine the role played by double bonds in the flotation of a very pure mineral using 18-carbon un-saturated fatty acids as collectors. Since zeta potential is dependent on adsorption and orientation of ions at the solid-liquid interface, its variation under different conditions of pH and collector concentration should throw some light on the behavior of unsatu-rated fatty acids in flotation pulps. Titanium dioxide, in the form of rutile, was chosen for the investigation because it is now available in a very pure, synthetic, crystalline state, and despite the fact that it is one of the most important synthetic inorganic chemicals in commercial use, its electro-kinetic properties have not been closely studied. Electrokinetic properties of rutile in various aqueous solutions are discussed in this paper. Adsorption information gained from the streaming potential measurements enabled the flotation resultsg to be explained in a qualitative way, thus providing a clearer

Jan 1, 1963

By R. C. Craze

This paper discusses the characteristics of the velocity logs now available to the petroleum industry, and some of their advantages and limitations. The velocity log was designed as an aid to the geophysicist to determine velocity layering in the earth and to provide fast, accurate and economical vertical travel time data. After a number of logs had been made, studies were carried out on their use ia correlating strata in adjacent wells. It was found that adjacent strata usually show sufficient velocity contrast to make it possible to correlate these from well to well, even in areas where electric or radioactive logs fail.' In addition, velocity logs have been useful in the determination of porosity and thickness of reservoir rock.' These uses for velocity logs require an understanding of the characteristics of the log in response to the changes in velocity and in borehole conditions encountered normally in logging. GENERAL DISCUSSION OF INSTRUMENTATION The measurement made in velocity logging is more accurately described as a measurement of time rather than velocity. Ideally the log is obtained by measuring the length of time required for compressional sound waves to travel through a fixed distance in the formation. In practice, the time measurement may be made accurately but the distance through which the waves have traveled may vary slightly. Changes in borehole diameter are responsible largely for the difficulty in maintaining a fixed distance, especially if the diameter variations are so abrupt and frequent that the borehole instrument cannot follow contours of the hole. Several service companies have velocity logging equipment available or under development which have different transmitters, receivers, and measuring systems. While these differences are important, there are actually only two systems in use at the present time (Fig. I)."' The first system initiates a pulse at a trans-mitter and detects it at a single receiver. The transmitter and receiver are separated by a fixed distance, called the spacing. The time measured is that between the initiation of the pulse and the first arrival of acoustical energy at the receiver. The second system uses two receivers and a transmitter. The receivers are separated by a fixed distance and the time between arrivals of energy at the two receivers is measured. Here, the spacing is the distance between receivers. The two systems have much in common for it is possible to record both logs simultaneously. Usually the transmitter is an electro-mechanical transducer which produces discrete

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson' indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel's' data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,' Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By Donald W. Petrasek

The effects of selected alloying elements on the elevated-temperature tensile properties of copper alloy -tungsten fiber reinforced composites were invcstigated. A cornparison of the elevated-temperature tensile properties of copper alloy - tungsten fiber reinforced composites, representing soluble systems. was made with copper - tungsten fiber reinforced composites, representing a mutually insoluble system. A linear relation between tensile strength and volume percent fiber content existed at elevated temperatures for all the systenzs investigated. The copper alloy composites were weaker in tension at high volume percent fiber contents than copper composites in which alloying with the fiber did not occur. The tensile strength of the alloyed tungsten fiber decreased with increasing penetration of the alloying element into Ihe tungsten fiber. THE technique of combining strong fibers with relatively weak matrix materials so that the fibers are load-carrying members has been utilized for many years in the reinforcement of plastics with glass fibers. This type of strengthening is currently being extended to include the reinforcement of metals with metallic fibers. Investigations of the room-temperature tensile properties of metal-fiber-reinforced metallic composites have been numerous,'-" but the study of tensile properties at elevated temperatures has been limited. In previous work done at the Lewis Research Center' composites consisting of mutually insoluble constituents were investigated. Composites were made of copper reinforced with uniaxially oriented tungsten fibers. The stress-strain behavior and tensile properties of the composites were related to the tensile properties of the base materials. The tensile strength of the composite was directly proportional to the volume percent of tungsten fiber present, and the full strength of the fiber was realized. Few metal fiber - metal matrix systems exist that are mutually insoluble, and those that do exist are not generally practical. An extension of this work was an

Jan 1, 1967

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By J. W. Pugh

PREFERRED orientations in cold-rolled body-centered-cubic metals appear to have remarkable similarity. The as-cold-rolled textures in iron,1,2 silicon-iron,3 mild steel,4 molybdenum, vanadium,&apos; chromium,&apos; tantalum,&apos; tungsten,&apos; and a-zirconium-niobium alloys10 have been determined. These textures have, in some cases, been represented by congrUOUS pole figures and have all been described in one or both of two ways. They have frequently been reported as predominantly (100) <011> orientation

Jan 1, 1959

By C. A. Siebert, D. J. Girardi

PRACTICALLY every metallurgical process in-volves, at some stage or another, the contact of a metal with a gas. Because of this, gas-metal re-actions are of great practical importance and have been subjected to numerous investigations. It has long been recognized that the presence of cuprous oxide in liquid copper has an important effect on its casting characteristics and .physical properties. This has led to the desirability of determining the quantitative relationships between cuprous oxide in the liquid copper and the usual gases present during processing. Such data are not only of practical importance but also of a theoretical interest in that they provide a means of applying the principles of physical chemistry to problems in applied metallurgy. The object of this investigation was to determine the quantitative relationship at equilibrium between the gases carbon monoxide and carbon dioxide and the cuprous oxide content of liquid copper. The reaction and its equilibrium constant may be expressed as follows: 2 Cu (liq) + CO2 (g) = Cu2O + CO (g) acu2o X aco/a2 cu X aco2 Here the underlined symbol Cu2O designates cuprous oxide dissolved in liquid copper and (a), the activity of the various constituents. The activities of carbon monoxide and carbon dioxide are assumed to be directly proportional to their re- spective partial pressures and the activities of cuprous oxide and copper are taken to be proportional to their respective mol fractions. The equilibrium constant may then be expressed as follows: K2 = Ncu2o X Pco [Ncu]2 X Pco2 where N = mol fraction The solubility of carbon monoxide and carbon dioxide in liquid copper is a rather controversial subject.&apos;-&apos; A review of the literature is given by 0. W. Ellis.&apos; It appears that carbon monoxide and carbon dioxide are both only very slightly, if at all, soluble in liquid copper. Volskii and Slobodskoi5 determined the equilibrium between carbon monoxide, carbon dioxide, and liquid copper at 1100°C. Their results show a higher cuprous oxide content for a given CO/CO2 ratio than found in the present work. The system hydrogen, water vapor, and liquid copper was investigated by Allen and Hewitt8 over the temperature range of 1090" to 1350°C. Equilibrium values for the system carbon monoxide, carbon dioxide, and liquid copper calculated from these data agree reasonably well with the present work. Materials and Procedure The copper used was oxygen free, designated as OF and analyzed as 99.98 pct copper with no appreciable amount of any one impurity based upon spectrographic determinations. The carbon dioxide was cylinder gas averaging about 99.95 pct CO2 with air as the major impurity. The carbon monoxide was produced by passing carbon dioxide over heated charcoal. Alundum combustion boats were used as containers for the liquid copper. No appreciable reaction took place between the copper and the alumina. This was evident from the fact that the copper sample after a run did not ordinarily adhere to the bottom of the boat and that the

Jan 1, 1951

By J. L. Rodda, R. L. Wilcox, E. C. Truesdale

IN recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on .the current equilibrium diagrams.. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I. of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part II of the paper the attempt is made to review all of the published work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data

Jan 1, 1935

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

By B. Egeberg

IN A previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature, between 200° and 450° F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress - tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy.

Jan 1, 1929

By A. B. Kinzel, Walter Crafts

Inclusions of nonmetallic matter have long been recognized as objectionable in steel. A complete theory of the effect of inclusions, which is consistent with that held today, was outlined in Howe&apos;s early work on the metallurgy of iron and steel. This, by analogy with wrought iron, assumes that the observed difference in properties between specimens with and across the direction of rolling is due to slag enclosures. The fact that wrought iron shatters in ballistic test is taken as an indication of the effect of inclusions on the resistance to&apos;shock. Since that time, the development of the metallurgical microscope has shown the discrete nonmetallic inclusions in the iron matrix. Better resolution has brought out the great number of inclusions, and the availability of good microscopes in steel mills and laboratories has constantly drawn more attention to these inclusions. This recent emphasis on inclusions has resulted in studies as to their nature, mode of formation and methods of elimination, such as the work of Wohrman, Dickenson, Herty and Schenk. In addition to the published works, many investigations which have not been published have been carried out by private laboratories and have resulted in the application of specifications intended to limit inclusions in many qualities of steel. Neverthless, a clear understanding of the quantitative effect of inclusions on the physical properties of steel has been lacking. It is the specific purpose of this study to determine the quantitative effect of inclusions on the physical properties of steel that determine its behavior under dynamic stress. The study has shown that a quantitative relation between counted inclusions and impact strength does exist in normalized steels, but that factors other than readily visible inclusions are equally important. Furthermore, the present commercial rating of inclusions is unreliable with respect to counted inclusions or dynamic tests, and this study indicates that the tensile-impact test is more reliable as a measure of quality. General Scheme The general plan of the study follows: (1) To develop or establish a satisfactory measure of dynamic strength; (2) to develop or establish a

Jan 1, 1931

By Arthur Notman

SacRamento Hill is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the masa of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chal-cocite with associated carbonates as stringers in a mass of strongly brccciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or SO places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface obscrved in the other disseminated deposits of the Southwest.

Jan 1, 1916

By C. C. Griggs

FROM its inception, a limestone quarry or mine should be under the direction of a capable engineer. Before it becomes a reality, he should outline the future results, plan the most economical methods for moving the materials and the most efficient equipment, and pilot the undertaking along the narrow pathway of success, avoiding the pitfalls of uneconomical production and the precipitous walls of scanty profits. Inspection of successful limestone properties shows that all have had difficult engineering problems, the solution of which have required keen engineering ability. In approaching a subject of this nature, it is logical to follow the progress of the limestone operation from its inception to the end, as reflecting the engineering required. There are four major divisions: Investigation, equipment, development, and operation.

Jan 2, 1925

By John H. Bassarear, Harold W. Sorstokke

The never ending search for lower unit costs led Pima Min- ing Company&apos;s management to study various alternatives shortly after Expansion III was completed. A considerable amount of ore as- saying 0.35% copper had to be moved to maintain mill feed at the desired 0.54 % copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8-10 yr, about 14,000 tpd of 0.30- 0.40% copper ore pass the crusher enroute to the low grade stockpile. This ore is very hard, very clean and has to be mined at a uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway), the major costs would be against milling. The decision to proceed was made in August 1970. Fluor-Utah was retained as the prime design construction contractor. Ore was put through the new mill on December 29, 1971. By March of 1972 design tonnage

Jan 5, 1973