Search Documents

By J. E. Berry

AII evaluation is made of the acoustic velocity log for measurement of formation porosity. Plots of field-observer1 velocities vs core-measured porosities of sandstones and limestotnes with inter intergranular porosity show that the velocity log gives a useful measure of porotity, in agreement with published data. A new method of plotting electrical and velocity log data makes it easier to recognize hydrocarbon-water coritnct~ from log darn and to make serni-quantitative estinlates of hydrocarbon saturation. Two examples of this interpretation technique are given. This paper also discusses the various factors that affect acoustic velocity and shows how corrections can be made for some of these factors. INTRODUCTION Although the continuous velocity log was developed primarily as an aid to seismic interpretation, it is finding widespread use for measurement of porosity. The purpose of this paper is to evaluate this use of the log. Results are presented for the velocity-porosity relationship in many sandstones and one limestone. Practical applications of porosity values derived from the velocity log to improve interpretation of electrical surveys are presented. Various parameters which affect velocity in porous media are considered. Porosity, composition, cementa-tion, pressure difference (overburden pressure minus fluid pressure), fluid saturation, and wellability are discussed. Some of the ideas are opinions based on general considerations of well logging problems while others are supported by published data and our own observations. Major conclusions from these studies arc given in the body of the paper and detailed discussions of some of the various factors affecting porosity are given in the Appendix. POROSITY Sandstones The primary factor affecting the velocity of sound in porous media is porosity. Wyllie, et al,1 have reported a time average equation for the relationship between velocity and porosity.* This has found considerable acceptance in the industry. Other relationships between velocity and porosity have been proposed, none of which are entirely satisfactory. It is doubtful that any one relationship will completely describe all situations. We have tried an empirical relationship based on correlating log velocities with core-measured porosities. Measured porosities were averaged over a depth interval equal to the spacing used in recording the velocity logs. The depth range for the information used was from 2,000 to 12,000 ft. Velocity measurements were normalized for the effects of depth and overburden pressure. A detailed discussion of the basis for this normalization is given in the Appendix. The change is usually insignificant and when working with individual formations it can be neglected. All velocity measurements were normalized to a depth of 10,000 ft. The velocity-porosity data for sandstones in Fig. 1 came from 20 wells scattered throughout the Mid-Continent and Gulf Coast areas. The scatter of the data points is attributed to three causes: 1. There is no theoretical basis for expecting an exact velocity vs porosity relationship and it is not possible to correct precisely for the effects of such factors as impurities, grain shape, manner of cementation, etc. Some of these factors are discussed in the Appendix. 2. Porosities measured by core analysis are not necessarily representative of what the velocity log "sees". 3. Inaccuracies appear in the velocity log reading. This is particularly true of velocities from one-receiver logging tools.*" A linear-time curve (time-average equation) is plotted in Fig. 1 along with the best straight line through the points. Velocities used for the linear-time curves were 19,500 ft/sec for the matrix velocity (zero porosity) and 5,500 ft/sec for fluid velocity. For clean sandstones with velocities greater than 10,000 ft/sec, there is little difference between the velocity-porosity and the time-porosity curves. Both curves are well within the scatter of data points. The data points in Fig. 1 were restricted primarily to clean sandstones, using the SP and/or gamma-ray logs as clues to the lithology. Where a lithologic de-

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By Kenneth A. Moon

An exact statistical treatment of a one-dimensional model is used as a basis for evoluating the reliability of certain simplified expressions for the activity of the solute in interstitial solutions, including one obtained from the exact expression by setting the repulsive interaction equal to infinity. The latter approximation is found to be satisfactory at low and moderate concentration if the repulsive interaction is large, even though not infinite. A similar expression (identical if the co-odination number is two) is derived from the quasichemical expression of Lacher, and is recommended as the best available expression for the excess configurational entropy of interstitial solutions with excluded sites. Some reasonable models are discussed, and the nature of the saturated solutions is determined by inspection. Some of the models reduce to the one -dimensional case. An analysis is given of the excess partial entropy of hydrogen in V-H; Nb-H; and To-H solutions. MOST treatments of the statistical thermodynamics of interstitial solid solutions have followed the classic paper1 of Lacher in making the simplifying assumption that the configurational entropy of the solution is ideal. However, it is becoming increasingly apparent that there are many interstitial solutions with very large so lute-solute repulsions, and for these the assumption of ideal entropy is not valid or useful. It is important to realize that with substitutional solutions large repulsions between the component atoms must lead to phase separation, whereas in interstitial solutions the free energy of the solution is not drastically increased by large solute-solute repulsions until intrinsic saturation is reached at the concentration where further solute would be forced to enter a site in which it would experience the repulsive effect of one or more solute atoms already present. In the limiting case of an infinitely large repulsive interaction, the excess free energy would be attributable entirely to excess entropy, the enthalpy of mixing being zero. AS will be shown below, even if the repulsions are less than infinite, a treatment based on an assumption of infinite repulsions may be very satisfactory up to moderately high concentrations of the interstitial component. Often in solutions where large repulsive interactions exist, there are also small interactions — often attractive—between solute atoms in configurations other than that corresponding to the large repulsion. In such cases the excess free energy will consist of an excess entropy term attributable to the large repulsive interactions, and an enthalpy term corresponding to the other small interactions. Nomenclature to differentiate succinctly between important cases would be a convenience. In this paper the nomenclature shown in Table I will be used. In Table I, and in the preceeding discussion, excess quantities are defined in terms of standard states which are pure solid solvent and pure (possibly hypothetical) solid saturated phase of the structure in question. In practice, it is more convenient to choose the interstitial element as a component, and its conventional standard state. This will add a composition-independent term to the excess entropy and the enthalpy. The earliest paper known to the present author which treats the thermodynamics of athermal interstitial solutions was given by schei12 in 1951, but the statistical derivations in that paper are open to criticism. Speiser and Spretnak were the first to give a correct statistical treatment,3 limited, however, to concentrations sufficiently low that the number of empty sites excluded from occupancy by more than one filled site is negligible. The purpose of the present paper is to extend the statistical treatment to more concentrated solutions, and to examine the magnitude of the errors introduced by assuming that the repulsive interactions are infinite when in fact they must be finite. THE QUASICHEMICAL APPROXIMATION Fortunately, a standard method already exists for taking into account the effect of large interactions upon the entropy of mixing. This is the quasi-chemical method, in which the probability of existence of a given pair of solute atoms in a certain proximate configuration is assumed to be proportional to exp(-w/kT), where w is the energy increase of the solution when the two atoms are moved from isolated locations in the solution to the configuration in question. A quasichemical treatment of interstitial solutions was given in 1937 in a widely neglected paper by Lacher.4 The result comes out

Jan 1, 1963

The following advertisements show the contemporary view of the value of coal on a tract, usually as compared with farming advantages of several kinds. Fayette Gazette and Union Advertiser, February 10, 1798: "For Sale in Washington twp., Fayette Co., 211 acres of land whereon is a good new grist merchant mill, a good stone dam, and a house for the miller, about two acres of bottom, cleared and fenced, an excellent coal bank and saw-mill seat unimproved." Pittsburgh Gazette, March 19 and 26, 1802: Ads. offering for sale two properties, one of 38 acres, "together with a Coal Pitt and Lime Quarry, lying on the Monongahela side of Grant's Hill, and within one mile and a half of Pittsburgh," and the other two tracts of 700 acres on "Racoon creek, contiguous to which is a valuable limestone quarry, and a quarry of building stone, also plenty of stone coal." Pittsburgh Gazette, Oct. 8, 1802: A farm between Pittsburgh and Greensburg "with house, barn and a Smith shop-also, a fine sugar camp, and a Coal Bank within sight of the house," was offered for sale. The Farmers Register, Greensburg, Pa., March 13, 1802: An advertisement of a "plantation, six miles from Greensburg, there are two coal banks on it, one at each end of the place." The Commonwealth, Pittsburgh, Aug. 4,1805: A number of lots were laid off on Saw Mill Run, nearly opposite the first opening made on the Pittsburgh seam. They were from two to twenty acres each "and a great quantity of Limestone and stone coal." Pittsburgh Gazette, Aug. 9, Sept. 6, Sept. 27, Oct. 4, 1811; The Commonwealth, Aug. 19, 1811: Five tracts were advertised that contained coal. One had "fine springs and an inexhaustible mine of coal;" one, "excellent sugar camps, coal banks and limestone and a good mill seat;" one, "good sugar camps, an excellent coal bank and an elegant seat for a distillery;" another, a tract of 45,000 acres in Allegheny and Butler Counties affording "stone coal and iron ore, and seats for water works;" and the last a tract on Beck's Run, four miles from Pittsburgh "and a coal pit opened about one fourth of a mile from the river." The Mercury, Pittsburgh, April 8, Jan. 14, Feb. 11, 1813; Pittsburgh Gazette, April 16, Dec. 3, 1813: These tracts were advertised during the year in the vicinity of the city. One had "a good sugar camp, woodland and plenty of coal;" another, "a sugar camp and a coal bank on the premises;" while the others were "well timbered or well watered and had excellent stone coal." The Mercury, Pittsburgh, Feb. 2, 1814: A farm was offered for sale on the headwaters of Robinson's Run, in Washington County, four miles from Burgettstown, containing 60 acres, "a young bearing orchard,... a coal bank and a good sugar camp." Genius of Liberty and Fayette Advertiser, Uniontown, Pa., March 2, 1814, carried an advertisement of a sale of lots in the new town of Perriopolis; "the quantity and quality of the clay, sand and salt licks, near the premises, together with the timber and abundance of .stone coals The town of Perriopolis was situated upon a . farm at one time belonging to Washington.

Jan 1, 1942

By William H. Case

The Bertha zinc-mines of the Bertha Zinc and Mineral Company are in that part of the State of Virginia popularly known as Southwest Virginia, and are included in that division of the " Great Valley " named in recent years the " New River-Cripple Creek Mineral-Region of Virginia." The mines lie wholly in the southeast part of Wythe county, two miles from Pulaski county on the east, and three miles from Carroll county on the south. The only other zinc-mines that are opened in the region are those of Manning & Squier, which adjoin the Bertha zinc-mines on the northeast, and the mines of the Wythe Lend and Zinc Company, at Austinville, eight miles to the southwest. A little farther southwest of Austinville, near Ivanhoe, a new company is preparing to mine zinc-ores. The mining properties named are included within a distance of ten miles along a direct line, bearing north 55' east, on the south side of New river, which here flows northeastward in a tortuous course. The greatest distance of any of the mine-openings from the river is a little less than two miles. It is not the magnitude of the operations in zinc-mining in this particular region, as compared with that of other well-known districts, that merits especial notice. Aside from the exceptional purity of the spelter made directly from the Bertha ores, some peculiar features of the zinc-ore deposih, as shown at the Bertha mines, and

Jan 1, 1894

By Theo B. Comstock

Since 1892 the writer has published several articles in the Engineering and Mining Journal concerning the relations of the

Jan 1, 1901

By Whitman E. Brown, Louis J. Erck

The installation in 1948 of a Hum-phrey~ spiral concentrator section at the Hill-Trumbull plant of The Cleve-land-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus ? in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 36 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus ? in. size. After de-sliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant. Overall recovery of the ball mill feed in the Hill-Trumbull spiral plant during the 1948 season was about 53 pct of the weight and 66 pct of the total iron content. Of the actual feed delivered to the spirals from the 78 in. classifier 64.9 pct of the weight was recovered containing 73.7 pct of the total iron. The average analysis of the spiral concentrate is 55.05 pct Fe and 14.83 pct SiO2. An average of mill assays during the 1948 season is given in Table 1. The Hill-Trumbull plants treat both wash ore and jig-type ore. During the 1948 season spirals were used only on the fine sizes of jig-type ore. At times the deslimed minus ? in. size is of sufficient grade to warrant bypassing the spirals but in the main the fine size is delivered to the 48 first stage spirals and thence to the 36 cleaner or second stage spirals. In the past several years numerous Mesabi Range ores in the fine size cate- gory have been tested by a wide variety of beneficiating equipment. The prodigious amount of research devoted to the recovery of values in the fine ore reflects the dire need of the iron industry to squeeze the last possible unit of iron from the mined ore and to develop suitable equipment and processes to satisfactorily concentrate the leaner horizons as they are encountered in the process of mining. Large governmental and private appropriations have been allotted, new laboratories built, research and technical staffs increased, and operator-manufacturer cooperative agreements applied to hasten the solution of the problem. The University of Minnesota, at its Eighth Annual Mining Symposium in January 1947, dedicated as its objective the bringing to light of technological developments in iron ore beneficiation. Papers were given at that time relating to processes being developed. Specifically, these papers reviewed flotation, Baum jig, selective media concentrator, Hardinge concentrator, Dorrco sizer, heavy media concentration, Hydrotator, and the Humphreys spiral. The Cleveland-Cliffs Iron Co., after encouraging results from tests in a small pilot plant using one full size spiral, made the first commercial installation of Humphreys spirals on the Mesabi Range at their Hill-Trumbull mine, Taconite, Minn. This company

Jan 1, 1950

By L. G. Huntley

I. HISTORY OF OIL DEVELOPMENT IN MEXICO THE occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopote" as a building cement.1 DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de Ias Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 ft. deep was drilled by a company organized in Mexico City, in what is now known as the Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said too have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican, Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State -

Jan 9, 1915

By Samuel Daniels

The Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such condition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400" to 600" F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400" F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600" F., the Al-Cu-Fe-Mg alloy at about 700" F. The former starts to reharden at 700" F., the latter at 800' F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500" and of 700" F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500" and 700" F. Although the latter can be made harder initially than the Al-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. Certain aluminum alloys have been used for pistons and other parts operating at temperatures up to 650" F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance to corrosion. In the piston, the inertia forces and the bearing loading, and with this the vibration, are decreased. The piston head functions at a lower temperature (about 200" F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design. The range in analyses of aluminum alloys, used for pistons in domestic and in foreign internal-combustion engines is shown in Table 1. There seem to be three general types of composition; one containing about 10

Jan 1, 1926

By J. C. Todd

The volume of air needed to move the combustion wave through each acre-foot of the reservoir is a very important quantity for engineering economic analyses. A new method, which involves backflowing the injection well, has been developed for determining the air requirement .for the forward combustion thermal pilot in the Delaware-Childers field. The method depends on measurement of the total volume of air injected and measurement of the pore volume in the zone swept out by the combustion front. The basic premise of the method is that the pore volume of the swept zone contains air, while the formation around this zone contains flue gas, oil and water. The pore volume of the swept zone is determined by blowing down the pilot section of the formation through the injection well after the pilot is shut down. Oxygen balance is used to differentiate between air from the swept zone and flue gas from the surrounding formation. Data indicate that air'is produced from the swept zone by relatively efficient miscible displacement by the flue gas. The pore volume occupied by the air in the swept zone is determined by simple PVT relationships. The average temperature of the swept zone is calculated by heat balance from the total amount of heat generated during the pilot and losses to the surrounding formation. The new method was applied successfully at the conclusion of the pilot in the Delaware-Childers field; the air required for the reservoir conditions involved was calculated to be 19.2 MMscf/acre-ft of reservoir swept. INTRODUCTION One of the most important pieces of information to be found from a forward combustion pilot is the air requirement; that is, the volume of air needed to move the combustion wave through each acre-foot of the reservoir. Compression costs per barrel of oil recovered, which are a direct function of the air requirement, are a large portion of the expenses incurred in the thermal recovery process. Thus, the profitability of thermal recovery depends largely on the air requirement, which is a measure of the amount of fuel deposited and burned in the thermal recovery process. Several attempts have been made to correlate crude oil properties with fuel deposition and, hence, air requirement.l*2 Other attempts have been made by our laboratory to find the air requirement by material balance, gravity survey, pressure transient analysis,3 magnetic survey and the poten-tiometric model. Better methods are needed to predict more accurately the economics of fieldwide application of the process. Another method of finding the air requirement consists of operating a pilot thermal project for several years. This is followed by an extensive coring program to define the volume swept by the combustion wave. The air requirement is found from the total injected air divided by the volume of the swept region found from the coring operation. This method is costly; an adequate coring program usually costs several hundred thousand dollars. A thermal pilot was operated in a watered-out portion of the Delaware-Childers field, Bartlesville sand, from Nov., 1960, until May 3, 1965. One of the primary purposes of this pilot operation was to determine the air requirement for economic calculations which determine the advisability of expanding the project to the entire 128,000 acre-ft field. Barnes4 has described the result of this pilot operation,, including calculation of the air requirement from limited coring data. The value obtained, as calculated, was 15.8 MMscf/acre-ft. One purpose of this report is to describe a new method of finding the air requirement from a thermal pilot operation. A second purpose is to describe the application of this method to the Delaware-Childers thermal pilot. THEORY AND DESCRIPTION OF THE METHOD The combustion zone in the forward combustion process is propagated from injection w producing

Jan 1, 1970

By Charles S. Barrett, Robert F. Mehl, Dana W. Smith

The Widmanstatten figures found in the steels have been long recognized and in some aspects carefully studied,' especially as they occur in cast hypoeutectoid alloys. Aside from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords to obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-statten figure of unique interest from the crystallographic viewpoint, particularly in comparison with those formed on slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By Edgar Bain

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin, Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By Clemens Catesby Jones

The substance of this paper, now amended and altered in form for its present use, was the basis of a private report prepared under professional engagement.* A private report is necessarily objective, and deprived of the scope and technicality of a scieintific treatise—which accounts for the prevalence of drawings and succinct mathematical statements rather than full descriptive details in a paper reproduced from data, of which all the original working-notes have been destroyed. In a practical sense the Hudson river valley clay-deposits owe their present existence to the protection afforded by the rock-formations on which they are supported, and, instead of being uniform in depth or continuity, are subject to the irregularities of the rugged masses which preceded and are now concealed by them. The only available information concerning these deposits contained in previous public reports or maps furnished at best a mere photograph of the surface, and as now apparent this was misleading or unreliable. It was the object of this investigation to determine in a practical manner the location, form and extent of all the clay-deposits at present existing in the lower Hudson river valley, and to ascertain with a

Jan 1, 1900

By R. S. Archer

THE binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.1 Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application.

Jan 1, 1930

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By E. A. Holbrook

The art of ore dressing is as old as civilization itself. Jason's search for the golden fleece was perhaps only the use of sheepskins for catching gold from gold-bearing sands washed over them. From Hoover's translation of Agricola we gather that in the middle ages ore dressing had advanced through the stage of hand sorting to water concentration by jigging. German methods and apparatus continued in the lead until the closing years of the past century; indeed, it is little more than a generation ago that many ore-dressing plants in this country were designed and operated by German-trained ore-dressing specialists. Meanwhile the development of the ore deposits in this country during the nineteenth century brought forth new inventions and methods. Blake's invention of the rock breaker in 1858 and the coming of the Wilfley table about 1896 are random examples of the improvements caused by our expanding needs. Yet ore dressing remained an art developed and practiced more or less by cut and try methods. The publication of the volumes on Ore Dressing by Dr. Robert H. Richards in 1903 marks the beginning of American ore-dressing practice as a science. Previously we had as guides only a few incomplete books based on foreign practice, or scattered references and articles in our own Transactions. Dr. Richards set down all the developments that had gone before, and outlined the ways for a scientific approach to the subject. He gave us a starting point. Since then ore-dressing practice and technique in this country have set the pace for the world. Coal preparation has been called "ore dressing upside down,'' because in ore dressing we generally save a small percentage of the heavy valuable mineral and discard the lighter gangue, whereas in coal preparation we save the larger quantity of light mineral and discard the smaller percentage of heavy waste. By comparison with ore dressing the history of coal preparation is brief, extending backwards hardly 100 years, for although coal had been dug and used locally for centuries it became an important article of commerce only with the coming of the industrial revolution 150 years ago. In new mines it was to he expected that the thickest and purest seams should be worked first. So long as these lasted there was little thought of coal preparation other than hand picking of the larger impurities and simple sizing to supply the real or fancied need

Jan 1, 1934

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949

By Robert H. Merrill, David W. Wisecarver, Raymond M. Stateham

The US. Bureau of Mines, in cooperation with US. Borax and Chemical Corp. and Kennecott Copper Corp., has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of micro-seismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron mine near Boron, CaL, and the Kimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nev. Microseismic monitoring within a frequency band of SO to 5000 Hz indicates noise rates in stable, inactive mining areas are between 0 and 10 noises per hour; the rates in stable, active mining areas are between 10 and 50 noises per hour; and the rate in unstable areas is as high as 2500 noises per hour. High microseismic noise rates in the Liberty pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic technique is applicable to large pit walls, and that the wide-band, wide-range microseismic equipment appears to be suitable for open-pit investigations. The microseismic method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. The method has been used for many years to detect incipient failure in roofs or pillars in underground mines. In 1963 the U.S. Bureau of Mines (USBM) started an investigation of the microseismic method in large, open-pit slope walls. The purpose of this investigation was to evaluate the method in open-pit slopes where the rock may be fractured and broken and where the size of the rock mass under investigation is much larger than normally encountered underground. In addition, both the stresses in the rock and the strength of rock near pits are lower than usually found underground. Consequently, there was some doubt concerning the feasibility of the method for open pits, and the economics of such an investigation may have been prohibitive especially if large walls had to be monitored with closely spaced geophones. The successful application of the microseismic method to underground operations has improved safety at little, or no sacrifice, to production or extraction ratios. The anticipated reward in open-pit mining would be the improvement of safety with a minimum sacrifice to mining operations. There is also a possibility that the method could be used to optimize the unloading (stripping) of potential failure areas by the removal of intact rock from the slope wall rather than the cleanup of a slide from the bottom of the pit. This report contains a brief description of three types of microseismic apparatus used in four different pit walls, each of which is different in height, slope, rock types, or has different planes of weaknesses, such as faults, fractures, or joints. Because the geologic features of the pit walls are varied and complex, for brevity, this report dwells mostly on the microseismic apparatus, techniques, the rock noise rates, and the slope movements measured at the various sites. PROGRESS AND DEVELOPMENT The microseismic method was developed over 20 years ago; and the method and examples of investigations in underground mines are summarized by Obert and Duvall. 1 In more recent years, the method has been applied in several underground mines, and an in-situ test under controlled stress conditions is described by Morgan and Merrill. 2 Experience has shown that, on occasions, the microseismic noise rate and amplitude reach a peak value and then start to decrease before a failure occurs in an underground mine; on other occasions, the noise rate steadily increases to a maximum at failure. The method has been applied to slopes by Goodman and Blake,3 and by Paulsen. 4 Goodman and Blake found that the noises corresponded with failures in the slope

Jan 1, 1970

By W. B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 1, 1961

By Anton Eilers, R. W. Raymond, O. H. Hann

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty