Search Documents

By Maurice Rey, H. Brevers

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

MARCH 15-Industry is rapidly snapping back from another coal crisis, other business news is in general favorable and the outlook through the Spring is by most observers considered quite promising. Most industries report comfortable backlogs of unfilled orders, department store sales in recent weeks have equalled in dollars those of the corresponding period last year, retail sales of automobiles show again over the same period a year ago, and new orders for machine tools are at the highest figures since August 1946. Orders for railway freight cars have shown a very encouraging pickup, with a total of 9385 cars in January and the N. Y. Central alone ordering 4500 in February. Construction continues very active. In January new housing starts totaled 80,000 against 50,000 a year ago and the daily average contract awards, according to the Dodge reports, were 57 pct larger. In the first 22 days of February the increase in awards was 27 pct. Lumber orders since Jan. 1 have run 22 pct above last year. All of these favorable factors bolster the opinion that the upturn in industrial output and employment which began last summer has not yet spent itself and that the setback caused by the strikes will be made up when people get back to work. Only in a few lines are there indications that primary production may be outrunning the consumption of finished goods, although inventory build-up would seem to be rather modest as the National Association of Purchasing Agents reported in February that 78 pct of its members were buying for 60 days or less. Industrial prices as a whole show no significant trend despite the continued alarm over both the immediate and the long-term possibility of inflation caused primarily by the government's increasing expenditure and its inability to balance the budget. A recent advance of 1.9 pct in primary market prices is viewed by some people as the surface symptom of renewed inflation, but even so it is more than two years since the alltime high was reached by the daily index of sensitive commodities in November 1947. Over two years have passed since prices received by farmers hit their peak and about a year and a half since all wholesale prices and the consumer price index touched their highest points in August 1948. The decline in the wholesale price index has been almost continuous, interrupted only twice by slight advances in the monthly figures from February to March 1949, and, later in the year, from August to September. Of course, this continued decline in the last half of 1949 largely reflects a downward movement in farm and food prices. Wholesale prices for commodities other than farm and food leveled out after June and now stand only slightly under the June level. Farm products are down by 22 pct from January and by 18.6 pct from August 1948. Food prices are down only slightly less. Consequently, the farm price support program is in serious trouble and has imposed a heavy financial burden on the Treasury. In those commodities other than farm products only building materials, chemicals and textiles have come down as much as the average, while housefurnishings and metals and their products have fallen hardly at all. Glancing away from the domestic front, the results of the British general election indicated a highly inconvenient situation, that public opinion there is so exactly deadlocked as to divest the victors of much ability to make forceful decisions or create significant policy. It is generally considered that another election in the near future would give substantially the same result. The British people are equally divided and the politicians are not likely to precipitate another appeal to the country until there is manifest reason to believe that external and internal circumstances have changed sufficiently to permit one party or the other to obtain a decisive verdict. Because of the lack of a clear mandate steel nationalization will likely lag in Britain. In the meantime there is considerable discussion going on as to whether the European steel industries as a whole are at a disadvantage in world competition with the American industry. An article in the "Statistical Bulletin" for January of the British Iron and Steel Federation takes issue on this point with the authors of the Geneva report, observing that they wrote before devaluation, and this particular conclusion "has been overtaken by events." The "Bulletin" also contends that the statement was in any case incorrect so far as Britain was concerned, and that it was based on scanty and insufficient evidence. To support the rebuttal a detailed and extensive comparison is made of the home prices of certain steel products in Britain and in other countries of the world. The accompanying table gives a selection of the prices published. It sets out the changed position since devaluation and since the recent increases in American steel prices. These are home market prices; no doubt in competitive export business some of the price levels could be brought closer together at need.

Jan 4, 1950

By David White

Jan 1, 1925

Established as a Division January 15, 1932 John C Calhoun, Jr, Chairman O Cutler Shepard, Vice-Chairman J R Van Pelt, Jr , Past Chairman Thomas A Read, Secretary-Treasurer Dept of Mining and Metallurgical Engrg University of Illinois Urbana, Illinois

Jan 1, 1956

By A. M. McQueen

Activity in the oil industry in Peru was somewhat above normal in 1928. Probably the most significant feature was the interest displayed in the oriental region in the northeast part of the country (Fig. 1). This region, though little known, has long been considered potentially rich in oil! gold, coal and other minerals, lacking only transportation to make it the country's most valuable source of income. The Standard Oil Co. of New Jersey, through its recently formed subsidiary the Standard Oil Co. of Peru, has acquired various tracts along the Maranon and Ucayali rivers in the neighborhood of the Brazilian border. Standard Oil Co. interests have had geological and surveying parties in this part of Peru since 1921, and as a result of the work done, we understand they have under lease at the present time some 2,500,000 acres of prospective oil lands. Development in the coastal region continued along normal lines during the past year. Production figures for both the International Petroleum Co. and Lobitos Oilfields show a small increase over the last few years. Total production figures since 1924 for the International Petroleum, Lobitos Oilfields and Zorritos companies, only in a minor degree estimated, are as follows: 1924, 7,924,700 bbl.; 1925, 9,138,042 bbl.; 1926, 10,750,676 bbl.; 1927, 10,110,696 bbl., and 1928, 11,969,677 barrels. International Petroleum Co., Ltd. Operations on the La Brea-Parinas Estate during 1928 continued with satisfactory results; nearly all branches showing improvement over the previous year. The average daily production for 1928 was 25,966 bbl., compared with 21,282 bbl. for 1927, an increase of 22 per cent. During the last two or three years, production methods on the company's property have been improved in line with the advance in scientific technique throughout the oil fields of the United States. Extensive investments were made in compressor equipment for handling surplus gas with the result that the gas-lift and repressuring operations are in no small way responsible for the increase in the 1928 production. In addition, the company's three casinghead plants produced 24,847,708 gal. of gasoline compared with 17,240,865 gal. in the previous year.

Jan 1, 1929

Vice-Chairmen GEORGE D. BARRON, PHILIP N. MOORE, EDWARD H. BENJAMIN, ROBERT H. RICHARDS, FRED H. BOSTWICK, MILNOR ROBERTS. ELI T. CONNER, CARL SCHOLZ. C. R. CORNING, WILLIAM WRAITH, WALTER DOUGLAS, THOMAS T. READ, Secretary, Woolworth Bldg.. New York, N. Y.

Jan 1, 1917

By C. R. Dale

IT IS the purpose of this paper to point out a number of the most common causes of crooked holes; to outline methods of drilling and straightening which to my personal knowledge have proved successful in numerous cases; to describe some of the characteristics of holes which, though not crooked in an exaggerated sense, may still cause serious mechanical trouble if not recognized and properly remedied; and to define clearly the part of oil-well surveying in the concerted effort operators generally are making to keep their wells straight from spudding to completion

Jan 1, 1931

By John Gross

THE method of measurement of surface on quartz particles was given in a previous paper.1 With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in .the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. THE CRUSHING DEVICE The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1-in. dia. by 1/2 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 ½ in. dia. by 3/4 in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of the chamber.

Jan 1, 1928

By LUIS EAIYLNN SALAS

IF the ordinary wet method be attempted for silver-bullion containing tin, much trouble is experienced, varying with the amount of tin present. Even with a percentage as low as 0.05, the end-point is masked by a persistent turbidity, while with amounts ranging from 0.5 per cent. upward, the determination of the exact end-point is impossible, owing to the finely divided or colloidal metastannic acid resisting all efforts to cause it to settle, or to give a clear supernatant liquid. The object of the following experiments was to seek a remedy for these difficulties, and to find the conditions whereby the Gay Lussac method might be applied directly to these bullions. Material containing tin is met with frequently in bullion from Mexico or Bolivia; and tin is carried (sometimes in large quantities) in jewelers' sweeps. 1. A bullion was prepared containing Ag, 74; Cu, 25; and Sn, 1 per cent. A weighed amount was treated by the humid assay-method as if it were an ordinary bullion free from tin. Ten cc. of HNO3 (1.21) was added, and the bottle was heated until all traces of red fumes had been expelled. Before heating, the solutions were moderately turbid; and after heating, the turbidity greatly increased. One hundred cc. of normal NaCl solution was added and the bottle was shaken vigorously at intervals during 30 min. The turbidity persisted. The bottle was allowed to stand over

Mar 1, 1912

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By K. L. Meissner

It is well known that the so-called pure aluminum contains noticeable amounts of impurities, chiefly iron and silicon, and many investigators have studied the forms in which these impurities exist. Hanson and Archbutt1 state that iron exists in aluminum as FeA13 and silicon as elementary Si. The solubility of FeA13 in solid aluminum is practically zero, or at least so small that the smallest trace of this compound is always visible as a separate constituent. Under the microscope an untrained eye can hardly distinguish, without etching, the two constituents FeA13 and Si, but they can be differentiated by suitable etching reagents. Anderson2 also found the same results. At the same time, Merica, Waltenberg, and Freeman3 found a constituent of unknown composition. They found a small thermal effect, at 610" C., on the cooling curves of aluminum with small amounts of iron and silicon. The intensity of this effect increased with increasing silicon content, until an effect occurred at 576" C. due to the eutectic between aluminum and silicon. The authors ascribed the effect at 610" C. to a compound, which they call "X constituent." It was thought to be a ternary compound containing iron and silicon and could be observed under the microscope as dark particles. Dix4 has published unetched photomicrographs of an aluminum with 0.51 per cent. iron, 0.99 per cent. silicon, and 0.32 per cent. copper that shows three constituents: the dark Si (black in the figure), the lighter FeA13, which appears in half tone and crystallizes in needles, and a constituent of the same color as FeAL3 but of different crystal form, often resembling Chinese script. This last constituent, Dix thought, is a compound of Fe and Si; not the compound FeSi but a compound containing a relatively small amount of silicon. Therefore an alloy of aluminum. iron, and silicon (the copper should not be regarded in the following considerations) must contain the following four constituents: Al, FeA13, Si, and a compound of Fe and Si. This, however, does not agree with the laws of chemical equilibrium.

Jan 1, 1926

OFFICERS AND COMMITTEES C C Long, President John Chipman, Past President J S Smart, Jr, Vice President T D Jones, Treasurer R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y D C Johnston, Assistant Secretary

Jan 1, 1960

The University of Colorado, Boulder, Colo. The University has published a volume, "Geology and Natura Resources of Colorado," by R D George The price is $2 and the volume may be had from the Campus Bookstore, University of Colorado, Boulder, Colorado.

Jan 1, 1933

THE morning session on mining methods with R. M. Raymond as chairman was devoted mainly to papers on explosives and the discussion of these papers. A paper on the numerical index of the re-sistance which rocks offer to the penetration of a drill bit was also read. The first paper, "Relation Between the Oxygen Bal-ance and Propulsive Strength of Eight Gelatin Dynamites" by G. St. J. Perrott, N. A. Tolch and J. E. Crawshaw, was presented by Mr. Perrott, super-intendent of the Pittsburgh Experiment Station of the U. S. Bureau of Mines. In this paper which is the beginning of a series of publications on explosives, Mr. Perrott stated that the attempt was made to put down in quantitative form the facts which have been known to explosive engineers for a long time. Eight samples of 40 per cent gelatin dynamite, with oxygen content varying from + 15 to - 36 per cent of the theoretical amount necessary to form complete combustion with all of the combustible elements were tested. The experimental work showed that a bal-anced explosive did not give the greatest propulsive strength-but the most favorable range was from - 8 to - 25 per cent oxygen. The experimental work also brought out the fact that the wrapper of a stick of dynamite enters quite completely into the explosive reaction, and gelatin dynamites from which the wrapper had been removed developed less strength than the a same explosive with the wrapper. The second paper, "Effect of Oxygen Balance of Gelatin Dynamites on the Gaseous Products of Det-onation," by G. W. James and G. St. J. Perrott, was also presented :by Mr. Perrott. The first portion of this paper is given over to a discussion of the relative merits of different types of apparatus for testing and analyzing the combustion products of dynamites. Three types were used (1) the Bichel gage, (2) the Crawshaw-Jones apparatus and (3) the Hercules tank. All three of these types were used in testing dynamites whose oxygen balance varied from-35 to + 6 per cent.

Jan 3, 1928

By Roswell Johnson

PENNSYLVANIA will be remembered, as long as oil is produced, as the cradle of the industry of petroleum in North America. It was on Oil Creek, near Titusville, Venango Co., .that Cola Edwin L. Drake, superintendent for the Seneca Oil Co., brought in the first commercial oil well on Aug. 28, 1859. Great difficulty was experienced in getting the well down to the producing depth of 69 ft. (21 m.) with the spring-pole system then in vogue for punching shallow water wells, so the novel expedient of driving an iron tube through the surface clays and quicksand was finally resorted to. The well had an initial yield of 25 bbl. a day on the pump, but soon went off, though 2000 bbl. were produced by the end of the year. With the Drake well a success, a young industry sprang into being, the rapid growth of which has been second to none in the country and the value of whose product is only surpassed by that of coal. For years the only producing territory, the Pennsylvania-New York field attained its greatest production in 1891, when the bringing in of the McDonald pool, between Pittsburgh and the West Virginia line, gave a total of over 33,000,000 bbl. At present the field, combined with West Vir-ginia and southeast Ohio, gives 25,000,000 barrels. GEOLOGY AND STRATIGRAPHY In general, the Appalachian field is a huge geosyncline, the axis of which runs roughly northeast-southwest, from north of the New York state line south through Brookeville, Kittanning, Pittsburgh, Washington, through the southwest corner of the state of Pennsylvania into West Virginia. Minor folding has accompanied or followed the dominant fold of the field, and it is from these structures near the Pennsylvania-West Virginia line and their influence on the accumulation of oil and gas that I. C. White, state geologist of West Virginia, obtained his evidence for anticlinal guidance of prospecting.

Jan 2, 1920

[ ]

Jan 1, 1938

By David J. Reddish, Barry N. Whittaker

The characteristics of surface ground strains due to longwall mining are reviewed with special reference to U.K. coal mining observations. The current empirical method of estimating ground strain is discussed. A method of determining surface ground strain above a longwall extraction is described whereby strain can be accurately represented along a line in any direction. The discussion is supported with examples of its application to common subsidence engineering problems.

Jan 1, 1984

By Frank M. Stephens, Robert D. Macdonald

As processes for handling low-grade or complex ores become more complicated and as new methods are found, the need arises for more complete and detailed pilot-plant studies to protect the capital investment required for a full-scale plant. Occasionally a process is firm technically, but there is a need for a demonstration plant that will convince nontechnical men of the wisdom of investing in a full-scale operation.

Jan 5, 1959

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962