Search Documents

By E. R. Hoskins

Results of a primary stress measurement investigation conducted on the 1100 copper ore body of the Mt. Isa mine, Mt. Isa, Queens., Australia, are presented in this chapter. The investigation started in September 1965, after discussion with the engineering staff at Mt. Isa, and consisted of both underground or in-situ tests at Mt. Isa and laboratory tests on Mt. Isa rocks and stress measurement techniques at the Australian National University in Canberra. Underground stress measurements were made in and adjacent to the 1100 copper ore body. The primary stress measurement site was in J 32 west crosscut on 14 Level. Approximate coordinates on the mine grid are 3000 north, 1650 east. The vertical depth below ground surface at this point is approximately 2180 ft. Some preliminary measurements were made in M 30 west crosscut on 13 Level, coordinates 3000 north, 2000 east, depth beneath the surface approximately 1990 ft. Additional flatjacks were installed on 11 Level in L 30 west crosscut, coordinates 3000 north, 2200 east, and depth beneath the surface approximately 1580 ft. All of the sites were in rock that from a mining engineering viewpoint must be considered extremely sound. The 13 and 14 Level crosscuts were approximately 14 ft on a side and nearly square and the 11 Level crosscut was approximately 10 ft on a side. All of the crosscuts had been standing open for several years and no artificial support of any type was necessary. Extraction openings hundreds of feet on a side have been made in this mine in similar rock and these have remained open also without additional support (see Davies 1 for a recent summary of mining techniques and conditions). The geology of the Mt. Isa mine has been most recently described by Bennett.2 Briefly, Mt. Isa is a silver-lead-zinc and copper mine in a series of Precambrian siltstones, shales, and bedded carbonates that strike north-

Jan 1, 1972

Jan 1, 1949

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS W E WRATHER, Chairman A B KINZEL -EARLE E SCHUMACHER DONALD H MCLAUGHLIN - JOHN R SUMAN FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERLE V DAVELER, Chairman PHILIP KRAFT - CLYDE E WEED

Jan 1, 1952

Underwood & Underwood HERBERT C. HOOVER ALBERT SAUVEUR CHAIRMAN OF WASHINGTON, D. C. CHAIRMAN OF BOSTON SECTION SECTION FREDERICK LAIST R. V. NORRIS CHAIRMAN OF MONTANA CHAIRMAN OF PENNSYLVANIA LOCAL SECTION ANTHRACITE SECTION CHAIRMEN OF SOME OF OUR LOCAL SECTIONS

Jan 6, 1919

By R. E. Zinkham

An investigation has been conducted to compare short transverse and longitudinal fatigue and fracture properties in 4.25-in.-thick, high strength aluminum alloy plates. One plate was produced using standard rolling techniques while the other was pre.forged before rolling. Little difference was shown in fatigue strength of longitudinal specimens taken from mid-thickness of the plate. Howeuer, in the short transverse orientation fatigue strengths at 107 cycles were about 25 and 50 pct less, respectively, for the preforged and standard rolled plate. Differences in fatigue strengths were attributed to grain size and shape as well US orientation of constituents. Fatigue crack propagation rates and fracture toughness were compared at three different stress intensity (K) levels, using a constant compliance, double cantilever, wedge-shaped specimen. In a given plate, comparable fatigue crack Propagation rates were observed in the longitudinal (i9W) and short transverse (TW) orientations. Somezuhat gveater rates were observed in the short transzerse (TR) orientation. The preforged plute gave a lower rate for all three directions. Considerable secondary cracking developed, at times, over portions of the fatigue crack in both plates, particularly at the lower stress intensity levels in the short transverse specimens. Micro structure revealed constituent stringers as possible causes of the crack branching. Fracture toughness was considerably less in both plates in the short transuerse orientation. It is concluded that preforging not only improved directional tensile properties but also the fatigue and fracture properties in general. On occasion, aluminum plates have been milled away for hinges or bolted connections and stressed through the thickness or short transverse direction. Little or no information is available concerning fatigue characteristics or fracture toughness in this loading orientation in aluminum plate, or of the effect of fabrication on these properties. It was the intent of this project to examine, develop, and apply a unique specimen that has been advocated by others to study the fatigue characteristics and fracture toughness of two differently fabricated high strength aluminum plates. Linear elastic fracture mechanics criteria may be applied to the specimen so that the fatigue crack propagation rate and fracture toughness data may be of use for design or inspection applications. Fatigue characteristics are generally measured in the longtudinal or long transverse direction, where fairly large specimens such as center notched panels,' are usually employed. Limitations are evident due to plate thickness, however, in the type and size of specimen that may be tested in the short transverse direction without extensions. Therefore, a specimen that is to be loaded in this direction should, for convenience, be compact. The general type of fatigue crack propagation specimens discussed and employed herein meet this requirement. These specimens are commonly called double cantilever beam specimens and lately "crackline-loaded edge-crack specimens".2 They may vary from a slope of zero (parallel-sides) to a wedge shape, the type employed herein. In general for most specimens the stress intensity KI at the tip of a crack is a function of the load, P and crack length, a. Some varieties of the wedge shaped specimen, however, give essentially a constant stress intensity KI over a considerable range of crack length.' This feature can be a valuable asset in fatigue crack propagation experiments because the stress-intensity can be controlled simply by controlling the load without regard to crack length. MATERIAL AND METHODS Material. A standard rolled (light pass reduction) and a ~reforged and rolled (heavy pass reduction) plate of 7179-T651 material were used for the evaluation. The chemistry, processing history and average tensile properties are shown in Table I. Specimen Selection and Preparation. The specimen selected for the generation of fatigue initiation or S-N data was an axial tension type and is shown in Fig. 1. Specimens were taken from mid-thickness in the longitudinal and short transverse directions from both plates. Specimens were polished with 500 grit paper in a direction parallel to the loading axis. For the fatigue crack propagation tests, the specimen shown in Fig. 2 was used. This is similar to a specimen that has been employed by Mostovoy3 for fracture toughness studies on 7075-T6 aluminum alloy. It also fortuitiously agrees quite well with the dimensions of a specimen for which Srawley and Gross2

Jan 1, 1970

By R. M. Brick, J. T. Richards

Tests have been conducted to determine the mechanical properties of several beryllium copper alloys down to liquid air temperatures. The materials investigated include beryllium copper, beryl-lium-cobalt-copper, and beryllium-zinc-copper in the wrought and cast conditions. As a means of evaluation, the influence of cold work and age hardening treatment upon subzero behavior has been observed. The effects of temperature upon both elastic and plastic deformation are also considered. THE low temperature mechanical properties of beryllium copper are of current interest in view of the increasing number of subzero applications. At extremely low temperatures, beryllium copper components are employed in temperature control and gas liquefaction equipment. At more moderate temperatures, such as those encountered in arctic regions, these alloys find use in a wide range of civilian and military applications. Although several previous subzero investigations have included beryllium copper,'-' none have been complete with respect to test temperatures or materials employed. As indicated in Table I, the alloy: used by Colbeck and MacGillivray,1 Walle,2 and Kostenets' were nonstandard and were not representative of present commercial practice. In addition, Kostenets4 did not test age hardened specimens, while the temperature in the other investigations", "-' were not carried below —100°F. These tests, however, indicate that beryllium copper offers interesting possibilities in subzero atmospheres, since the increase in strength with decreasing temperature is not accompanied by a reduction in ductility or impact resistance. As a means of checking and extending this earlier work at subzero temperatures, an investigation was undertaken at the University of Pennsylvania. In addition to testing the standard 2 pct beryllium copper, other alloys were also considered in wrought and cast forms. Charpy impact and tension tests were included with particular emphasis on the elastic characteristics, since beryllium copper is frequently selected for its spring qualities. Nominal test temperatures were +80°, —75", —200°, and —300°F. Test Materials Wrought beryllium copper, beryllium-cobalt-copper, and beryllium-zinc-copper specimens were machined from 0.560 in. diameter rod. These alloys were tested in the solution treated, cold drawn, or age hardened conditions. In the case of solution treated beryllium copper, some specimens were aged (3 hr at 600°F) for maximum hardness and others were overaged (1 1/2 hr at 750°F) to determine the effect of heat treatment. The compositions and average room temperature properties of these wrought alloys are presented in Table 11. The casting alloy versions of beryllium copper and beryllium-cobalt-copper were prepared as sand-cast cylinders, roughly 3/4 in. diameter x 6 in. long. Test specimens were machined from these cylinders. Conditions tested included as cast as well as solution treated and age hardened. Table 111 lists compositional and room temperature property data for the cast alloys. Test Methods Tension tests were conducted on specimens having a 0.25 in. diameter reduced section over a 1 in. gage length. To insure axiality, specimens were loaded by means of hardened chains. The yield strength at 0.2 pct offset was obtained from autographically recorded stress-strain curves resulting from a spe-

Jan 1, 1955

[OH. O'C. Acker '86 Jinzoc Adachi '88 *Truman H. Aldrich '78 Walter H. Aldridge '89 *Anson W. Allen '87 *John H. Allen '84 *Thomas Andrews '94 *William R. Appleby'90 *W. Lawrence Austin '82 . S. Ayres'73]

Jan 1, 1946

W. M. CURSE, Mansfield, Ohio.-Outside of the commercial valu-ation of the material, for what purpose does this alloy-90 per cent. of copper, 6 ½ per cent. tin, 2 per cent. zinc, and 1 ½ per cent. Lead-seem to be eminently fitted? C. P. KARR.-So far as our tests go, it would be eminently fitted for steam valves and pistons, and for the work for which 88-10-2 bronze is generally used, although for very large castings it would not be superior to 88-8-4 bronze. P. E. MCKINNEY, * Washington, D. C.-Some time hack, clue to a desire to avoid some of the objectionable features of 88-10-2 bronze, particu-larly on heavy castings, also to save tin where possible, we took up the question of a substitute for 88-10-2 bronze, where red bronze was ordinarily specified. After trying most of the mixtures, we found that when using as low a tin content as is given in this proposed composi-

Jan 12, 1919

(Under this heading will he published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 488.-Mining engineer, member, technical graduate, married, age 38, desires position of superintendent or assistant superintendent. Has had 15 years' practical experience as miner, millman, machinist, surveyor, engineer, foreman, and superintendent in the West, Southwest, and Mexico. Speaks Spanish. Now employed as superintendent of copper property in Southwest. Can give the best of references. Minimum salary $250. Available now. No. 491.-Mining engineer, member, married, age 43, desires to connect with some-good coal company as superintendent or manager. Is thoroughly conversant with flat and pitching systems of coal mining. Has had 23 years experience from the bottom up; 7 years experience as superintendent and manager. Good organizer. Has handled all classes of labor acid has always made good. Available now. No. 492.-Metallurgist and chemical engineer, member, with 8 years executive experience in research and technical direction of all departments of nom-ferrous metallurgical manufacturing, is open for change in position. Specialist in raw materials-and supplies, reclamation of wastes, and standardized control of processes. No. 493.-Member, age 37, technical education, married. Seventeen years' experience as superintendent, engineer, chemist, and assayer, exploration engineer in United States, Central and South America, Siberia and India. Especially in iron, manganese, copper, and rare metals. Desires to make a change. No. 494. Electrometallurgical engineer, member, age 30, A. M. and Ch. E. degrees, thoroughly trained in electrochemistry, metallurgy and electrometallurgy. Three years in charge of experimental work on and operations of electric furnaces. Desires responsible position in investigative or executive work with commensurate salary.

Jan 11, 1918

By M. J. Marcinkowski, D. B. Crittenden, A. S. Sastri

A study co.mbining stress-strain .measurements in conjunction with transmission electron microscoPy has been made with near equiatomic Fe-Cr alloys which were aged for various times at 500°C. Associated with this aging is a marked increase in deformation twinning. The outstanding feature of these twins is that they generate stress fields sufficiently great so as to give rise to spontaneous dislocation loop nucleation nearly normal to the propagating twin. This observation is in agreement with the theoretically predicted elongation of the stress field of a dislocation Perpendicular to its direction of motion as it moves near the speed of sound. Dislocation loop nucleation is more difficult in the longer aged alloys so that this energy absorption mechanism is not effective in hindering twin propagation. Since crack nucleation can readily occur near the tip of a twin, the aged alloys become extremely brittle when deformed in tension. Iron-chromium alloys in the vicinity of the equiatomic compositions become severely embrittled when aged at about 500°C. Fisher et 01.' have shown that this embrittlement is related to the decomposition of the original random Fe-Cr solid solution into a chromium-rich and an iron-rich phase. In addition, Mar-cinkowski et a1.' have shown that twinning becomes an increasingly more important mode of deformation as the aging time is increased. These results have been recently corroborated by the transmission electron microscopy study of Mima and amauchi . The Fe-Cr alloy thus seems ideal for verifying the predictions made in Parts I4 and 115 of this investigation where the behavior of large static or blocked twins and those of large dynamic or propagating twins, respectively, were investigated numerically. It was thus decided to measure the stress-strain curves generated by embrittled alloys that were aged for various times and to examine sections by transmission electron microscopy. EXPERIMENTAL PROCEDURE Electrolytic iron and electrolytic chromium were vacuum-melted and poured into ingot form. The composition of the resulting alloy was found to contain 46.0 wt pct Cr (47.8 at. pct), the remainder being iron. The resulting ingot was swaged above 850°C into 0.250-and 0.400-in.-diam rounds. Compression samples of 0.250 in. diam and 0.400 in. long were cut from the smaller-diameter rounds. These samples were then sealed in evacuated quartz tubes and annealed for 30 min at 1150°C to produce a uniform and equiaxed grain size of mean diameter equal to 1.73 mm. They in turn were rapidly quenched from 850°C so as to preserve the condition of random solid-solution characteristic of the elevated temperature. The samples were then aged for various times up to 300 hr at 500°C in a massive Pb-Bi alloy bath. The samples were next polished and tested in compression at room temperature as described in Ref. 6 using an Instron tensile testing machine. The strain rate used was 0.05 in. per in. per min. The remaining larger round was converted into compression specimens of 0.325 in. diam and 0.500 in. long. This larger diameter enabled wafers of sufficient size to be prepared for examination by trans-mission electron microscopy techniques after subjecting them to a suitable strain. Foil preparation is described in some detail in Ref. 6. All foils were examined in a type HU-11A Hitachi electron microscope operating at 100 kv. RESULTS AND DISCUSSION Fig. 1 shows the effect of aging at 500°C on the room-temperature stress-strain curves of the FeCr alloys. For greater clarity the origin of each curve has been displaced upward. The same origin has been used for both the 0 and the 0.1 curves. It is apparent that with increased aging times a sharp drop in load is observed at the yield stress which becomes more pronounced as aging proceeds. A loud sonic burst accompanies this drop and subsequent metallographic examination shows the sample to contain numerous twins. For intermediate aging times, a number of smaller twin bursts follow the initial large one. The total plastic strain associated with the twinning mode of deformation can be obtained by adding up the contributions AE~ from all i twin bursts, i.e., £,¦££,-, in the manner illustrated schematically in Fig. 2. The contraction of the specimen, as measured from the strip chart of the Instron, after suitably correcting for the elasticity of the machine, was converted into true strain using the assumption that there was no volume change and that the sample remained cylindrical. The dashed lines are all drawn parallel to the

Jan 1, 1970

A Report Of Current Activity In The Industry

Jan 7, 1951

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

MINING METHODS F A WARDLAW, JR, Chairman WILLIAM J COULTER, Past Chairman PHILIP B BUCKY, Past Chairman FRANCIS CAMERON, Vice-Chairman R D LONGYEAR, Vice-Chairman J MURRAY RIDDELL, Vice-Chairman LELAND A WALKER, Vice-Chairman E D GARDNER, Secretary

Jan 1, 1952

By William H. Kobbé

THE CHAIRMAN (M. L. REQUA, San Francisco, Cal.).-We have had in California a great deal of trouble from the breaking. off and collapsing of well casings from shifting sand, and it is quite true with us as indicated in the paper, that no casing has been found sufficiently strong to withstand that. I know of wells in which casing that has not been in the hole over 2 or 3 days has collapsed and when that casing has, been pulled out it has been just as flat as your hand. I am also familiar with swelling bed rock in the gold drift mining ground of California. It does swell and keeps on swelling and never seems to stop. Just as long as tunnels are kept open in that kind of material there has to be a gang going through the tunnel constantly cutting out and easing up. They have put in timbers 24 in. in diameter in an effort to hold that kind of ground and it has always filled. The only way to succeed is to keep a gang of men busy all the time cutting out and easing down as it squeezes in. C. NARAMORE, Washington, D. C.-My experience has been very similar to yours in, the same field in the matter of breaking off of casing. I had charge of one well, in which I put in reënforced casing, anchored it in place and got 1 day's production, 150 bbl., out of it. The following morning my lease foreman telephoned that it had broken off. I thought at that time we would have more evidence, so I drove out to the well without ordering a new shoe joint. It had been customary to merely start from town with a new shoe joint, pull the pipe, take off the crooked bottom joint, start the casing back and sometimes never touch any iron (lost casing)- when redrilling the well. Where the flattened joints went

Jan 4, 1917

By R. D. Pehlke, P. D. Goodell, R. W. Dunlap

The rate of dissolution of steel bars in molten pig iron has been measured experimentally in the temperature range 2300° to 2650° F. The rate of solution is shown to be a .function of bath composition, temperature, and stirring. A kinetic model based on carbon diffusion in the liquid phase has been derived to fit the experimental results. THE rate of scrap melting has long been an important variable in steelmaking operations. With the advent of the oxygen steelmaking process and the accompanying shorter heat times, the rate of scrap melting has now become one of the rate-limiting factors in steel production. As observed in commercial practice, the solution rate is influenced by the compositions of liquid and solid, the temperature, agitation, and time. However, no definitive work has been done on the Fe-C system, and there is very little information in the literature regarding the relative effects of these variables in steelmaking systems. A number of questions have been raised in regard to scrap utilization in basic oxygen steelmaking operations. Consideration has been given to the optimum size and shape of scrap, and to the use of preheated scrap as a means for decreasing the pig-iron requirement in oxygen blowing. The determination of an optimum scrap practice for a specific installation depends to a large extent upon the economics of the scrap market and also upon the behavior of scrap in the vessel. The present research was undertaken as a preliminary study in evaluating the behavior of steel in a pig-iron bath under various conditions of temperature, composition, and agitation, as might be encountered in oxygen converter operations or in any steelmaking operation where scrap behavior is an important process variable. Related studies have been carried out on non-ferrous systems. The solution rate of solid aluminum in a molten A1-Si alloy has been studied.' Furthermore, the increasing use of liquid metals has created considerable interest in studies related to dissolution of a solid in a liquid, or mass transfer taking place between a solid interface and a liquid metallic phase.2-10 In an effort to clarify the relative importance of factors influencing the dissolution of scrap in Fe-C alloys, this paper presents the results of a study of the rate of dissolution of a low-carbon steel cylinder in a molten Fe-C bath at various bath compositions, temperatures, and conditions of agitation. An attempt has been made to determine the mechanism of solution, and a model has been derived to fit the experimental results. The rate of heat transfer between the molten pig-iron bath and the solid-steel cylinder has also been studied. EXPERIMENTAL PROCEDURE A molten bath of pig iron (nominal composition 4.2 pct C, 0.5 pct Mn, 0.8 pct Si)* was held in a 200- *In view of the fact that the composition of the pig-iron bath was slowly changing with time because of steel dissolution and reaction with the surrounding atmosphere, intermittent samples of the liquid bath were taken throughout each experiment, Table 1. lb induction melting unit. The internal diameter of the furnace was 8-1/2 in. and the bath depth approximately 14 in. Cold-finished 1020 steel cylinders of 1/2-, 3/4-, 1-, 1-1/2-, and 2-in. diameters were cut into 1 -ft lengths for use as test specimens. One end of each bar was machined to fit a hand-driven, mechanical stirring device which rested on top of the furnace. This fixture permitted 7 to 8 in. of the bar to be immersed in the melt. The steel cylinders were cleaned to free the surface of grease and oxide. The rods, at ambient temperature, were immersed into the molten pig-iron bath. The melt temperatures studied in this investigation were 2300°, 2500°, and 2650°F. Different agitation conditions were achieved by operating with a) the power to the furnace, giving induction stirring; b) induction stirring plus mechanical stirring, using hand rotation with a chain and sprocket assembly at approximately 200 rpm; c) mechanical stirring alone with the power off; and d) the power off and no mechanical stirring resulting in minimum agitation, i.e., only that caused by natural convection currents in the bath. The samples were immersed in the melt for prescribed times ranging from 30 sec up to 6 min. Immersion times were measured with a stopwatch and temperature control of the melt was achieved by power adjustment following temperature measurement with an optical pyrometer. The measurements with the calibrated pyrometer were checked out to within less than 10°F with simultaneous thermocouple measurements. Following immersion, the bars were water-quenched and the diameters were measured with a micrometer at several positions on the reduced area, and by volumetric displacement. The dissolution rates calculated from the

Jan 1, 1965

By J. A. Morgan, R. E. Lund, D. E. Warnes

The design, operation, and performance of an integrated pilot plant for recovering zinc and copper from a complex sulfide ore are described. Metallurqical processing comprised selective sulfate roasting in a fluid bed, leaching in a weak sulfuric acid solution, recovering copper by cementation with scrap iron, air oxidation to remove soluble iron, more-or-less conventional Purification for removal of impurities deleterious to zinc electrolysis, recovering zinc by electrolyzing solutions, and recycling spent electrolyte to the sulfating roaster. The effects of several feed preparation and roasting variables on the sulfation response of zinc, copper, and iron are set forth, together with the electrolyzing characteristics of the zinc solutions. SEVERAL years ago, St. Joseph Lead Co. undertook a research program to develop procedures for winning values from a complex ore. The deposit was a massive sulfide ore body containing upwards of 65 pct pyrite. Gangue, composed principally of quartz, calcite, dolomite, and alumina, comprised only 10 to 20 pct of the mineralized zones. Zinc, lead, and copper values were variable, but averaged about 6.7 pct Zn, 2.6 pct Pb, and 0.4 pct Cu. Early in the exploratory test work, it was established that the intimate physical association of the minerals in the ore made beneficiation by conventional flotation procedures difficult. Accordingly, in addition to a comprehensive program to investigate physical methods of ore beneficiation, a research program was established to develop a direct metallurgical method for processing the ore. After surveying a number of potential methods for recovery of both metal and sulfur values, effort was concentrated on the development of a sulfate roasting process. It is the pilot-plant development of the sulfate roasting-solution purification—electrolyzing procedures which forms the subject of the present paper. PREPILOT PLANT INVESTIGATIONS From a thermodynamic viewpoint, it is feasible to sulfate selectively a host of metals, including Zn, Cu, Pb, Cd, Ni, and Co, in an iron sulfide ore without sulfating iron. Of course, a number of conditions such as roasting temperature and gas composition must be controlled. In addition, as first disclosed by Hybinette,' an alkali metal salt is frequently beneficial in promoting the sulfation reactions. The application of fluid bed roasting to the sulfate roasting of nonferrous metals was pioneered by Stephens of Battelle Memorial Institute.' Subsequently, Falconbridge Nickel Mines, Ltd. developed an unique process for selectively sulfating and recovering nickel, copper, and cobalt from their nickeliferous pyrrhotite, which recently has been described in an excellent paper by Thornhill.3 One of the unique features of the Falconbridge process is that the feed is introduced into the fluidized roasting furnace in a manner such that the feed slurry is broken up into droplets and the droplets lose their moisture before contacting the surface of the fluidized bed. The dried droplets do not tend to cake or fuse, but rather remain as discrete agglomerates of concentrate particles and roast without significant degradation. St. Joseph, aware that Battelle Memorial Institute had participated in the development of the Falconbridge process, obtained permission from Falcon-

Jan 1, 1962

MOWRY BATES, ? Tulsa, Okla.-In the first part of this paper the author says: "In an unpublished paper on Water Problem in the Augusta Field, S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked

Jan 4, 1919

Arrangements have been completed in New York whereby the re- sources of The Engineering Foundation, under the auspices of the four principal national engineering societies, are placed at the disposal of the National Research Council, which was appointed by the National Academy of Sciences* at the request of President Wilson. The object of the Council is to coordinate the scientific research work of the country in order to secure efficiency in the solution of the problems of war and peace. The Council was without funds until The Engineering Foundation, established to further scientific and engineering research, offered to place its resources at the Council's disposal, including the services of its secretary, Dr. Cary T. Hutchinson, to act as-secretary of the Council. The offer was accepted and plans for immediate activities have been placed in the hands of an executive committee. In indicating how thoroughly, every branch bf science and engineering is represented, Dr. George E. Hale, Director of the Mt. Wilson Solar Observatory, and Chairman of the Council, when he was in New York attending to the details of the arrangement, called attention to the personnel of the body, saying that it is the purpose to enlist the cooperation, in the solution of our industrial and military problems of a scientific character, of every possible established agency. Medicine, for example, is represented on the Council by Dr. William H. Welch, President of the National Academy of Sciences, Brigadier General William C. Gorgas, , Surgeon Crenera.1 of the United States Army, Dr. Simon Flexner, Director of the Rockefeller Medical Institute, and Dr. Victor C. Vaughan, Past President of the American Medical Society; biological science by Dr. Edwin G. Conklin, Professor of Zoology, Princeton University; chemistry by Dr. A. A. Noyes of Massachusetts Institute of Technology and Dr. L. H. Baekeland; physics by Dr. A. A. Michelson of the University of Chicago; and electricity by Professor M. I. Pupin, of Columbia University.

Jan 10, 1916

By B. E. Parsons

Curtailment of production of crude oil, to the extent of effecting an approximate balance in supply and demand, was a problem confronting the oil industry in California throughout the year 1930. At the beginning of the year, with drilling operations only slightly checked, the California industry faced a steadily increasing potential production, an actual production in excess of market requirements and stocks of crude oil and refined products which had reached staggering proportions. During the year, the intensive development of the Playa Del Rey field and extensions to several oil fields, together with flush production from numerous large wells from both new and old fields, caused a steady increase in the state's potential production to a record peak in November of 1,186,000 bbl. daily. Despite the burden of this steady stream of flush production and the handicap of incomplete cooperation in several fields, curtailment successfully lowered the trend of crude oil production in California, except for the period of an open-flow test to determine actual potential production in several important fields in February. Under the curtailment programs in effect, the state's production of crude oil for the year was reduced 22 per cent. under the production of 1929 and even slightly under the production for the years 1927 and 1928. The total stocks of crude oil and refined products were reduced 2.7 per cent. during 1930, as compared to an increase of 30 per cent. in total stocks of all products during 1929. Drilling operations were reduced 28 per cent. as compared to drilling activities during 1929. Voluntary curtailment of drilling programs by many operators, particularly the major companies, accounts for the greatest portion of the reduction in drilling activity. The decline in drilling activity at Santa Fe Springs and in the east-side fields of the San Joaquin Valley was more than offset by development in new fields and extensions to deeper zones of old fields. There were 755 new wells completed during 1930, as compared to 910 completions in 1929. At the close of the year, 220 wells were drilling in the oil fields of California, 9 of which were being drilled in search of deeper producing horizons.

Jan 1, 1931

By J. B. Macelwane

GEOPHYSICS differs from geology and physics in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, volcanology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratory system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist-the exploration geophysicist -calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist-the paleontologistneeds some knowledge of geology. DEVELOPMENT OF A GEOPHYSICIST Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydrologist, or an exploration geophysicist? We may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1941