Search Documents

By Thomas M. Dr. Drown

IN experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

W: 0. HOTCHKISS, Madison, Wis. (written discussion*).-Mr. George's paper on. "The Wisconsin Zinc District" is a very complete and clear description, which it is a pleasure to read. His discussion of the origin of the ores is the least satisfactory part, and Mr. George correctly states present knowledge when he begins his paragraph on a origin with the words "the general supposition is, etc." There is still much to be learned regarding the details of the processes by which the ores have reached their present situation. In this the Wisconsin district differs not at all from other mining districts. It is my hope that Mr. George and others, equally clear-thinking, who are in close touch with these operations will be able at an early date to give us more information on this subject.

Jan 3, 1918

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By Lawrence H. Van Vlack, Otto K. Riegger, Gerald I. Madden

The microstructural variations of periclase (MgO) in the presence of oxide liquids are examined under the steelmaking variables of: 1) temperature, 2) liquid composition, and 3) FeO additions under different oxidation levels. Attention is given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. Silicate liquids penetrate more extensively between individual periclase grains than do liquids containing high percentages of Fe2O3 Higher MgO solubilities in the liquid and lower MgO contents of the solid favor more rapid grain growth. The presence of a second solid phase reduces the periclase grain growth rate and increases the amount of the solid-to-solid contact within the oxide microstructures at high temperatures. The service suitability of a refractory depends on many factors. Two are of major importance and include 1) the thermal resistance to melting, and 2) the mechanical resistance to loads at service temperatures. Neither is a simple consequence of the service temperatures because service conditions will alter compositions, produce partial melting, and induee phase changes. Consequently, the equilibrium phase relationships have been rather thoroughly studied and give a knowledge of the thermal resistance to melting, but do not give full information about the mechanical properties because two refractories with the same types and quantities of phase may have different microstructures. Although variations of microstructures with time, temperature, and composition have been subjects for extensive investigation in metals, only a limited amount of comparable microstructural work has been performed for refractory materials.' This study was an attempt to evaluate some of the consequences of service parameters upon the microstructures of refractories so that bases may be established for the analyzing of high temperature mechanical properties. Periclase (MgO) was chosen as the refractory oxide; variables included those which are encountered under steelmaking conditions such as 1) temperature, 2) liquid composition, and 3) FeO additions under various oxidation levels. Specific attention was given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. The most closely related work on microstructures of polyphase materials is that of Van Vlack and Rieg-ger2 on the microstructure of magnesiowüstite [(Mg,Fe)O] in the presence of silica. In that work which pertained to solid solutions with less than 40 pct MgO, most of the quantitative work was performed on FeO microstructures. The chief conclusions concerning these relatively low-melting oxide solids were as follows: 1) the rate of crystalline grain growth is inversely proportional to the grain diameter, 2) grain growth proceeds more rapidly at higher temperatures but is slightly retarded by additional liquid content, and 3) a Silicate-containing liquid penetrates as a film between the individual magnesiowüstite grains independent of time, temperature, amount of liquid, or the MgO/ FeO ratio. The above observations are in contrast to prior work3 on the microstructure of silica in the presence of iron oxide-containing liquids where the liquid does not penetrate as a complete film between solid grains. The phase relationships for the compositions of the present work are shown in Fig. 1 which is a summary of the work of several investigators.4 Of importance is the fact that CaO forms a more stable structure with SiO2 and Al2O3 than do either MgO or FeO. The oxygen potential has little effect on periclase unless iron oxide is also present. The iron oxide is ferrous at moderately low oxygen levels, changing to ferric as the Oxygen potential is increased so the spinels, magnetite, and magesioferrite are formed.5 These two phases are relatively stable in air at steelmaking temperatures. I) EXPERIMENTAL PROCEDURE ractory were made with reagent grade Oxides. The magnesium oxide used was 99 pct MgO after ignition, and the iron oxide raw material had a minimum content of 99 pet Fe2O3. The CaO, SiO2, and A12O3 were also reagent grade raw materials. After mixing, the required compositions were pressed into pellets at a minimum pressure of 5000 psi to insure compaction of the raw materials and prevent excess void content. A silicon carbide element tube furnace was used with thermocouple control for sin-

Jan 1, 1963

By W. R. Clough, M. E. Shank

IT has been noted in a study of the flow and fracture of nodular cast iron under biaxial stress conditions (complete results of which will be published later) that when this metal is subjected to stress it may undergo a striking density change. Such behavior was first determined by strain gage measurements made on tensile test specimens, and has since been substantiated by other types of measurement. The chemical analyses and mechanical properties of several nodular irons to be discussed here are given in Tables I and 11. Tensile data for iron A was obtained from a hollow cylindrical combined stress specimen of the same dimension as those used by L. F. Coffin, Jr.1 in his investigation of gray iron properties. Standard 0.505 in. solid tensile-test bars were used for irons B and C. On each specimen type, A-8 wire resistance strain gages were used—two diametrically opposing gages in the axial direction, two in the tangential or hoop direction. By subtracting elastic strains from the measured strains, the plastic strains could be calculated. By assuming that radial and tangential strains are numerically equal, a measure of permanent volume change can be obtained by summing the plastic strains. This appears to be a good assumption, since the metal either fractured, iron A, or readings were discontinued, irons B and C, long before necking took place. This calculated variation of volume increase with stress is given for irons A and B in Fig. 1. Data for iron C is almost identical with that for iron B. The volume change indicated by Fig. 1 has been substantiated by a more direct type of density measurement. A method developed by S. G. Fletcher and' Morris Cohen,' and completely described in the discussion of their article, has been used. The accuracy of specific volume measurement has been estimated as 0.00002 cu cm per gram. Essentially the method consists of weighing a sample in air and then immersed in water. Measurements were made before and after straining the material. The results shown in Table I11 were obtained by means of half-size (0.252 in. diameter, 1 in. gage length, 3/8-16 threads) tensile specimens. Initial measurements were made on the whole specimen before stressing. After stress-

Jan 1, 1955

By R. P. Carreker

GERMANIUM is a member of that group of ele-nents—carbon, silicon, germanium, and tin-— that are currently of particular interest because of their interesting electrical properties. Near room temperature these materials of diamond cubic crystal structure are characteristically brittle. However, there have been several recent reports that germanium is not brittle at elevated temperatures These observations may be summarized as follows: 1—Germanium single crystals were observed to creep in bending under a maximum fiber stress of 6 kg per mm&apos; (8500 psi) at 500°C and above.&apos; The creep curves were sigmoidal, with an induction period that decreased with increasing temperature. 2—Germanium crystal bars have been bent 90" about radii ten times the bar thickness at 550°C.&apos; 3—-Audible clicks were heard when l/4 in. thick crystals were bent drastically at 450" to 500°C. No microstructural evidence of mechanical twinning was observed 4—Slip lines have been observed in tensile specimens deformed at 600°C, and are coincident with (111) planes, the close-packed planes of the diamond cubic structure.] The slip direction has not been established. 5—A germanium crystal has been compressed approximately 20 pct along a <110> axis at 700°C." The results reported subsequently were obtained in exploratory experiments intended to indicate some aspects of the behavior of germanium single crystals when tested in simple tension. Specimen Preparation A single crystal bar of n-type germanium was used. It was of purity corresponding to a resistance range of 2 to 20 ohm-cm. Tensile specimens were prepared by cutting small rectangular bars

Jan 1, 1957

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940&apos;s it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By Reaves. M. J.

The title of my talk, "What Happened to the Uranium Boom?" is old news. Certainly it is for this group. All of us that make our living in uranium know that the boom of the last half of the 1970&apos;s is over. U.S. production has been exceeding consumption by more than two to one. Mines and mills are closing and yellowcake prices have been dropping for over 20 months. The gloomy outlook for the industry in the near term has been well documented by soothsayers of various descriptions, your daily newspapers, and in the Nuexco Monthly Reports. I&apos;d like to attempt to describe the next upturn in the market (speculate, really) based upon the clues we&apos;re seeing now. In order to do that, I&apos;d first like to go over briefly, some of the market factors that contributed to the recent price drop and resultant production cutbacks, and then hypothesize on the way these factors are changing and will change. Market prices are greatly affected (maybe even entirely determined) by buyer perceptions. This is particularly true with uranium, because of the long lead times associated with nuclear plant construction and also with conventional mine/mill development. Before the price rise (say, 1975) utility uranium buyers believed that: 1) U.S. producers would have difficulty expanding to meet U.S. demand. 2) Australian and Canadian production was essential to avoid shortages in the early 1980&apos;s. 3) Uranlum prices would continue to rise as demand exceeded supply. 4) Enrichment capacity would become inadequate. It was thought necessary, therefore, to build enriched inventory in the early 1980&apos;s for use in the late 1980&apos;s. Artificially accelerated expansion of the uranium producer industry was necessary to accommodate anticipated enrichment demand. Current perceptions are largely the opposite. These are the beliefs that were held most of this year and late last year as prices dropped. 1) U.S. production is far in excess of domestic need. Contraction of the U.S. production lndustry is necessary. 2) Canadian and Australian supply is optional and not essential. Producers in those countries are expanding mainly by displacing higher cost production and not because they fill a void, 3) Prices may be essentially stable for some time. 4) Enriched uranium is in excess supply. That is 1981. 1982 is shaping up to look like this: 1) Prices will have bottomed out. (That is not Nuexco&apos;s opinion necessarily, by the way, but it is my opinion.) 2) There will still be substantial utility inventories, but fewer spot sales. 3) Canadian and perhaps Australian sellers will have made substantial sales in the U.S. and will be aggressively seeking more. 4) U.S. production will have been dramatically curtailed. U.S. utilities that wish to con- tract long term will have difficulty in finding domestic sellers. Concern will develop about the availability of U.S. production capability. Virtually all long term con- tracts signed will be with non-U.S. sellers. 5) An awareness will begin to develop among U.S. buyers that we are approaching a period of dependence upon foreign uranium (which will be true). The history of the uranium market has been one of dramatic changes and overreaction to those changes. The rapid price rise of a few years ago generated excess U.S. production capacity and the rapid price drop of the last two years will almost certainly result in too little capacity. It will soon be difficult for U.S. buyers to buy domestic material except on the spot market. The question is, "will they care?" The lack of demand, of course, is the underlying reason for the current poor health of the uranium industry. In 1972, 1973 and 1974 collectively, there were 105 nuclear reactors ordered in the U.S. That ordering rate was expected to continue and accelerate throughout this century. In 1975, 1976, 1977, 1978, 1979, and 1980 altogether, there were 56 more reactors cancelled than ordered. The net growth of our only customer since 1974 has been a negative 56. TO put this in perspective, if these 56 reactors were operating now it would more than double present U.S. uranium consumption. Underlying lack of demand is something that is simply not going to change in this decade. Time is going to be required. The NRC indicates that the maximum feasible number of new reactors that can be licensed each year is six. That would increase uranium consumption by only 10% per year. New reactors, if ordered tomorrow, would not generate new uranium demand until after 1990. Even so, United States&apos; consumption of uranium will rise from the 1980 level of 18 million pounds per year, to

Jan 1, 1982

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By M. J. Marcinkowski, A. S. Sastri

A detailed compressive stress-strain analysis and transmission electron microscopy investigation has been made of the deformation behavior occurring in a 50 at. pct Ni-Ti (hypoeutectoid) alloy and a 54.5 at. pct Ni-Ti (hypereutectoid) alloy. In the case of the hypoeutectoid alloy, three stages of work hardening are observed. Stage I occurs at a very low stress and is associated with plastic deformation via martensite formation. Stage 11 is characterized by very rapid work hardening and is due to difficulties in causing further deformation in the fine martensite aggregate produced in Stage I. Stage III which occurs at very high stress levels is characterized by smaller work hardening rates and is due to the plastic deformation arising from alternate reconversions of the original martensites to martensites of varying orientation. Rapid quenching of the hypereutectoid alloy leads to very high yield strengths and is related to a fine precipitate dispersion that such treatment brings about. The present investigation represents the final phase of a three-part study directed toward an understanding of the solid-state transformations in near equi-atomic Ni-Ti alloys as well as the deformation mechanisms associated with these alloys. In the first part,"2 to be henceforth referred to as I, it was found that alternate simple shears on {112} planes and in (111) directions convert the parent B2 structure in the equiatomic NiTi alloy into two distinct close-packed monoclinic martensites. All of the marten-sites were of this type, whether they were formed by cooling or by plastic deformation, whether induced to form in bulk samples or in thin foils, or whether examined in the electron microscope at room temperature or below. On the other hand, in the second part of this investigation,3 to be reffered to as 11, it was shown that upon slow cooling to about 640°C. alloys in the neighborhood of NiTi which possess the B2 structure transform eutectoidally into their equilibrium phases Ti2Ni and TiNi3. However, preceding the formation of these equilibrium phases a series of metastable intermediate phases are formed. This paper will set as its goal the elucidation of the remarkable deformation behavior exhibited by NiTi. In particular, Buehler and Wiley4 have found equiatomic NiTi to be surprisingly soft, while Buehler et al.5 have shown this alloy to possess a memory effect: i.e., upon bending at room temperature it will revert to its original shape when heated to above about 50°C. In I it was shown that NiTi was soft in the sense that the yield stress was low; nevertheless, the alloy work-hardened at an extremely rapid rate to very high stress levels. On the other hand, the hypereutectoid alloys with somewhat higher nickel, say 54.5 at. pct (60 wt pct) have enormously increased yield strengths compared to those of the equiatomic alloys. In order to determine the atomistic processes giving rise to the above behavior, it was decided to examine samples that were wafered from bulk specimens deformed in compression to various strains using the techniques of transmission electron microscopy. EXPERIMENTAL TECHNIQUE All of the alloys used in the present investigation contained either 50 at. pct Ni (55.06 wt pct) or 54.5 at. pct Ni (60 wt pct) and were arc-melted in the form of a finger using the same techniques described in I and II. The finger was capsulated in a stainless-steel jacket and swaged at 850°C into rods. Compression specimens 0.300 in, long and 0.200 in. in diam were machined from these rods. In order to completely re-crystallize the samples and remove residual stresses, all of them were capsulated in evacuated quartz, annealed for 1/2 at 1050°C. and then furnace-cooled. Compression tests were carried out in an Instron tensile testing machine covering a range of temperatures from —196° to 200°C using procedures described previously.6&apos;7 In all cases crosshead speed was 0.02 in. per min. Wafers 0.015 in. thick were spark-cut from the cylindrical samples at 45 deg to the compression axes after they had been deformed to the desired strain. These specimens were then spark-planed to about 0.005 in. and then electrochemically thinned for examination by transmission electron microscopy as described in I.

Jan 1, 1969

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing&apos;. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing&apos;, There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry&apos;s law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H&apos; is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

By Vittal S. Bhandary, B. D. Cullity

Swaged iron wire has a cylindrical {001} <110> texture. The texture is also cylindrical after re-crystallization in the absence of a magnetic field, but <111> and <112> components are added to this texture when recrystallization occurs in a field. The mecizanical properties in tension and in torsion are not greatly altered by these changes in texture. AS shown in a previous paper,1 cold-worked wires of the two fcc metals copper and aluminum can be made relatively strong in torsion and weak in tension, or vice versa, by proper control of preferred orientation (texture). The deformation texture can be controlled by selection of the starting texture (texture before deformation), because certain initial orientations are stable during deformation. The present paper reports on similar work performed on bcc iron. In this case it was clear at the outset that there was no hope of controlling the deformation texture, which is one in which <110> directions are aligned parallel to the wire axis. (1t has usually been regarded as a fiber texture, but Leber2 has recently shown that it is a cylindrical texture of the type {001} <110>. In either case, <110> directions are parallel to the wire axis.) There is general agreement on this texture among a large number of investigators, which in itself suggests that the starting texture has no influence on the deformation texture. More direct evidence was produced by Barrett and Levenson,3 who reported that iron single crystals of widely varying initial orientations all had a single <110> texture when cold-worked into wire. Thus <110> is a truly stable end orientation for iron and probably for other bcc metals as well. Under these circumstances attention was directed to the possibility of controlling the recrystallization texture. This texture is normally <110> in iron,4 just like the deformation texture. However, it is conceivable that this texture could be modified by a proper choice of the time, the temperature, and what might loosely be called the "environment" of the recrystallization heat treatment. In the present work the environmental factor studied was a magnetic field. The effect of heating in a magnetic field ("magnetic annealing") on recrystallization texture has been investigated by Smoluchowski and Turner.5 They found that a magnetic field produced certain changes in the recrystallization texture of a cold-rolled Fe-Co alloy. The texture of this material is normally a mixture of three components, and the effect of the field was to increase the amount of one component at the expense of the other two. Smoluchowski and Turner concluded that the effect was due to magnetostriction. With the applied field parallel to the rolling direction, the observed effect was an increase in the amount of the texture component which had <110> parallel to the rolling direction. In the Fe-Co alloy they studied, the magnetostriction is low in the <110> direction and high in the <100> direction. Thus nuclei oriented with <110> parallel to the rolling direction will have less strain energy than those with <100> orientations and will therefore be more likely to grow. In a later paper on the same subject, Sawyer and Smoluchowski6 ascribed the effect to magneto-crystalline anisotropy and made no mention of magnetostriction. In the papers of Smoluchowski et al. the intensity of the magnetic field was not reported but it was presumably large, inasmuch as it was produced by an electromagnet. In the second paper6 it is specifically mentioned that the specimens were magnetically saturated. But if magnetostriction has a selective action on the genesis of stable nuclei during recrystallization, that selectivity must depend only on differences in magneto-strictive strains between different crystal orientations and not on the absolute values of those strains. Thus the saturated state does not necessarily produce the greatest selectivity, because the relative difference in magnetostrictive strains between different crystal directions may be larger for partially magnetized crystals than for fully saturated ones.7 In the present work the specimens were subjected to relatively weak fields (0 to 100 oe) produced by solenoids. MATERIALS AND METHODS Armco ingot iron rod (containing 0.02 pct C and 0.19 pct other impurities) was swaged from 0.25 in. in diam. to 0.05 in., a reduction in area of 96 pct. The mechanical properties in tension and torsion were measured as described previously.&apos; Textures were measured quantitatively with chromium or iron radiation and an X-ray diffractometer,8,1 and

Jan 1, 1962

By L. W. Davies

ONE of the most important applications of the zone-melting process of Pfann1 concerns the refining of materials with respect to impurities whose distribution coefficient k differs from unity. The repeated passage of molten zones along an ingot concentrates the impurities for which k < 1, for example, towards the end to which the zones move. It is desirable to know the ultimate distribution of impurity after the passage of an infinite number of zones of constant length; this is also the distribution which is unchanged by the passage of a further molten zone.

Jan 1, 1959

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7&apos;his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By B. D. Smith, K. H. Coats

Experiments in which calcium chloride displaced sodium chloride from four cores showed the extent of asymmetry in the resulting effluent concentration profiles. These results provided a check on how validly the mixing process is modeled by a differential (i.e., not finite-stage) capacitance mathematical model. The effluent concentration profile from two consolidated cores exhibited considerable asymmetry, while two unconsolidated cores yielded nearly symmetrical profiles. All runs resulted in breakthrough of the 50 per cent concentration significantly before one pore volume was injected. In addition, velocity appreciably affected the effluent concentration profile from a Torpedo sandstone core. The differential capacitance model matched the data significantly better than a simple diffusion model. The capacitance model allows determination of the amount of dead-end pore space in a porous matrix and the effect of velocity on the rate of diffusion into this space. An experimental program yielding insight into the physical validity of the capacitance effect is described. INTRODUCTION Axial dispersion — the mixing accompanying the flow of miscible fluids through porous media — has been the subject of many relativeiy recent studiesl-13 and a comprehensive review of the topic has been given by Perkins and Johnston.14 This dispersion is of practical interest in studies of the miscible displacement process, fixed-bed chemical reactors, and the adsorption of solutes from a flowing stream onto the surface of a porous medium. In the latter case, the effect of dispersion must be considered when adsorption parameters are determined from the nature of concentration profiles. In general, early studies of dispersion assumed applicability of a simple diffusion equation and were concerned with correlation of the experimentallv determined "effective" diffusion coefficient with system properties over a large range of the latter. Recent have been concerned with the deviations between the asymmetrical effluent concentration profiles observed and the symmetrical ones predicted by the diffusion model. In the present study, effluent concentration profiles were obtained from consolidated and unconsolidated cores. These profiles were compared with those predicted by a differential (i.e., not finite-stage) capacitance model. Solutions to the simple diffusion model, for three sets of boundary conditions, were compared with one another and with the experimental profiles. SUMMARY OF PREVIOUS WORK The reader is referred to Perkins and johnston14 for an extensive review of studies of dispersion in porous media. Many investigators have employed the simple diffusion model characterized by Eq. 1 below: The dispersion coefficient D for unconsolidated systems is correlated by u is interstitial velocity and dp is particle diameter. Since heterogeneity of the sand pack affects the mixing, this equation is also expressed as where a is proportional to the degree of heterogeneity and is about 3.5 for random packs of unconsolidated sand.l4 Eq. 3 holds for 2 For a Do homogeneous (regular) type of packing, should be 1 or less.6 Aris and Amundson6 and Carberry and Bretton consider o to be the number of particle lengths per mixing cell in the finite-stage model. Data from consolidated cores indicate dp to be about 0.36 cm for outcrop rocks, Torpedo sandstone having a reported value of 0.17 cm.15 For v /Do less than about 2, the effect of molecular diffusion must be considered and the total dispersion coeffi-

Jan 1, 1965

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel&apos;s composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of &apos;some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement&apos;s gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that&apos; faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By A. Kavetsky, W. J. Whiten

Data from ball mills with a wide range of diameters are analyzed using detailed mathematical/ numerical models. Analysis shows the relative power inefficiency of large ball mills is due to their inefficient breakage of coarse particles. The models developed can be used to scale-up mill behavior. The behavior of large mills at Bougainville and Pinto Valley is compared. It is concluded that the mills are equally inefficient at grinding coarse particles. Differences in coarseness of total mill feed are shown to account for the fact that Pinto Valley mills achieved design throughput whereas Bougainville mills did not.

Jan 1, 1985

Mining Methods LUCIEN EATON, Chairman GERALD F. SHERMAN, Vice-chairman CHARLES W. WRIGHT, Secretary Alluvial Mining CLINTON BERNARD CHARLES H. MUNRO CHARLES JANE N H. R. NORSWORTHY Open-cut Mining Iron MAX H. BARBER J. A. MacKILLICAN Copper MICHAEL CURLEY H. B. TEMPEST Underground Mining Iron C. H. BAXTER CARL BREWER TENNEY C. DESOLLAR Copper W. B. DALY A. H. WOHLRAB R. W. THOMAS

Jan 1, 1934

Jan 1, 1955