Search Documents

November 21st, 1871. THE first session of this meeting was held Tuesday evening, in the chamber of the Common Council, the President, Mr. David Thomas, in the chair. Mayor Carroll, of Troy, gave a cordial welcome to the Institute, which was responded to, on behalf of the Institute, by the first Vice-President, Mr. R. W. Raymond. The Council reported the names proposed for membership with recommendation for election. The following named gentlemen were duly elected Anthony, J., - Williamstown, Pa. Babcock, George, - Troy, N. Y. Blake, Theo. A., - San Francisco, Cal. Blossom, T. M., - New York. Boalt, James A., - San Francisco, Cal. Bowman, Amos, - San Francisco, Cal. Chester, Prof. A. H., - Clinton, N. Y. Dewey, C., - Pittsfield, Mass. Dock, Gilliard, - Shamokin, Pa. Emerson, G. D., - New York. Endres, John J., - Pittsburgh, Pa. Firmstone, Frank, - Easton, Pa. Fowle, W. B., - Philadelphia, Pa. Frazier, Prof. B. W., - Bethlehem, Pa. Gardner, George A., - New York. Goodyear, Watson A., - San Francisco, Cal. Griswold, Chester, - Troy, N. Y. Griswold, J. A.,* - Troy, N. Y. Hague, J. D., - San Francisco, Cal. Hahn, O. H., - Eureka, Nev. Harkness, T. C., - Wilkes-Barre, Pa. Harris, Samuel, - Hudson, N. Y. Henry, E. T., - Oxford, N. J. Holley, A. L., - Brooklyn, N. Y. Howe, H. W., - Troy, N. Y. Hunt, Dr. T. Sterry, - Boston, Mass. Jannet, J., - Troy, N. Y. Knapp, John A., - New York. Laughlin, Henry A., - Pittsburgh, Pa. * Since deceased.

Jan 1, 1873

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

[ ]

Jan 1, 1938

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

E. H. Dix, JR., Chairman L. W. M. PEIRCE, Past-chairman R. F. MEHL, Vice-chairman ALBERT J. PHILLIPS, Vice-chairman E. M. WISE, Secretary International Nickel Co., Bayonne, N. J. W. M. CORSE, Treasurer LOUIS JORDAN, Executive Secretary 29 West 39th St., New York, N. Y. Executive Committee W. H. BASSETT, JR. R. H. LEACH' W. H. FINKELDEY W. E. REMMERS2 J. A. GANN H. J. ROAST G. O. HIERS C. S. SMITHS L ZICKRICK

Jan 1, 1936

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By H. P. Stüwe

HE recent papers of Aust and Rutter112 have again brought to mind the importance of certain "special" orientation relationships between the lattices of two fcc crystals on the mobility of the grain boundary separating them. No theoretical treatment of this problem has been offered till now. The only principle published so far that has given an indication why certain orientation relationships should be "special" is the counting of "coincidence sites" according to the suggestions by Kronberg and Wilson.3 The "coincidence plots" published by these authors show, for instance, that two fcc lattices rotated by 38 deg around a common (111)-axis have 1/7 of their lattice sites in common. Such an orientation relationship is also characteristic for high boundary mobility. The accuracy of the orientation relationship needed for high mobility is not too rigid. Deviations up to 10 deg from the ideal orientation seem to be tolerable as can be gathered from the experimental data.'j4 The auestion arises, then. how the density of coincidence sites will be affected by a deviatioi from mathematical accuracy. This can be checked by a simple model. Two sieves are prepared, the arrangement of the holes corresponding to lattice sites on a (111)-plane in a fcc crystal. They are placed upon each other, Fig. 1. One is kept fixed, the other is rotated around an axis pushed through one hole in common to both. The light falling through holes of both sieves is then a measure for the density of coincidence sites. If the diameter of the holes is very small, light intensity is contributed only by holes the centers of which coincide "exactly." If the diameter of the holes is rather large, some intensity will be contributed by

Jan 1, 1962

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,&apos; the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson&apos;s number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis&apos; in graphical form. In 1953 Fatt&apos; also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie&apos; equation, and the more general Winsauer equation&apos;, where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By H. M. Morse

This report covers the period from Jan. I, 1943 to Dec. 31, 1943. During the year, II2 wells were drilled in Mississippi, as foilows: wildcats drilled and abandoned, 54; wildcats producing oil, 4; oil wells drilled in oil fields, 26; oil wells drilled in fields, dry and abandoned, 10; sulphur-test wells drilled, 14; salt-water-disposal wells, 3; core tests, I. Prospecting Geophysical work in Mississippi during 1943 amounted to 1127 crew weeks, divided as follows: reflection seismograph, 809 weeks; gravity meter, 285; magnotometer, 30; torsion balance, 3. A considerable amount of core drilling was done over a large part of the state. The complete data on this activity are not available at the present time. Salt Domes To date, the following salt domes have been discovered in Mississippi: Midway, Edwards, Glass, Newman, Tatum, Oak-vale, Kings, Halifax, D&apos;Lo, Hazlehurst, Byrd, Leedo, Prentiss, Carson, Moselle, Monticello, Ruth, Keno, Taylorsville. New Oil Fields Lincoln County.—On March 10, 1943, the California Company completed its Smith No. I in sec. 4, T. 7 N., R. 7 E., Lincoln County, as an oil well and produced 29 bbl. of 25" gravity oil in 24 hr. through a fi-in. choke. Two outpost wells have been drilled in this area by the California Company, and both have been abandoned as dry holes. Madison County. —Love Petroleum Co. completed its J. R. Anderson No. 2, sec. 2, T. 8 N., R. I W., Madison County, on Sept. 7, 1943. This well produced 135 bbl. of approximately 30" gravity- oil in 24 hr. through a )/4-in. choke. The production comes from a sand or porosity in the upper part of the Chalk formation of the Cretaceous age. Adams County.—The California Company drilled its National Gasoline Co. of Louisiana No. I in sec. 52, T. 7 N., R. I W., to a total depth of 10,383 ft., and at 10,280 ft, it perforated and obtained gas and a condensate. The well had several showings in the Wilcox of the Eocene age. Several of these showings were tested and the well finally was completed at 5888 ft. on Oct. 6, 1943, producing 44" gravity oil in the second sand in this formation. No other wells were completed in this field during the year. However, a number of wells are contemplated in the near future, and locations have been staked by the California Company. The Oklahoma Pipe Line Co. will market the oil through its pipe-line facilities. Wayne County.—The Gulf Refining Co. drilled Davis No. I in sec. 2, T. 9 N., R. 9 W. in Wayne County. After several stem tests 545&apos;-in. casing was set at 6850 ft. and production was obtained in the so-called Massive Sand of the Lower Tuscaloosa. The well produced 359 bbl. of oil in 24 hr., and it Was completed on Oct. 4, 1943. Other locations have been staked ill this area and probably will be drilled in 1944 by

Jan 1, 1944

By H. M. Morse

This report covers the period from Jan. I, 1943 to Dec. 31, 1943. During the year, II2 wells were drilled in Mississippi, as foilows: wildcats drilled and abandoned, 54; wildcats producing oil, 4; oil wells drilled in oil fields, 26; oil wells drilled in fields, dry and abandoned, 10; sulphur-test wells drilled, 14; salt-water-disposal wells, 3; core tests, I. Prospecting Geophysical work in Mississippi during 1943 amounted to 1127 crew weeks, divided as follows: reflection seismograph, 809 weeks; gravity meter, 285; magnotometer, 30; torsion balance, 3. A considerable amount of core drilling was done over a large part of the state. The complete data on this activity are not available at the present time. Salt Domes To date, the following salt domes have been discovered in Mississippi: Midway, Edwards, Glass, Newman, Tatum, Oak-vale, Kings, Halifax, D&apos;Lo, Hazlehurst, Byrd, Leedo, Prentiss, Carson, Moselle, Monticello, Ruth, Keno, Taylorsville. New Oil Fields Lincoln County.—On March 10, 1943, the California Company completed its Smith No. I in sec. 4, T. 7 N., R. 7 E., Lincoln County, as an oil well and produced 29 bbl. of 25" gravity oil in 24 hr. through a fi-in. choke. Two outpost wells have been drilled in this area by the California Company, and both have been abandoned as dry holes. Madison County. —Love Petroleum Co. completed its J. R. Anderson No. 2, sec. 2, T. 8 N., R. I W., Madison County, on Sept. 7, 1943. This well produced 135 bbl. of approximately 30" gravity- oil in 24 hr. through a )/4-in. choke. The production comes from a sand or porosity in the upper part of the Chalk formation of the Cretaceous age. Adams County.—The California Company drilled its National Gasoline Co. of Louisiana No. I in sec. 52, T. 7 N., R. I W., to a total depth of 10,383 ft., and at 10,280 ft, it perforated and obtained gas and a condensate. The well had several showings in the Wilcox of the Eocene age. Several of these showings were tested and the well finally was completed at 5888 ft. on Oct. 6, 1943, producing 44" gravity oil in the second sand in this formation. No other wells were completed in this field during the year. However, a number of wells are contemplated in the near future, and locations have been staked by the California Company. The Oklahoma Pipe Line Co. will market the oil through its pipe-line facilities. Wayne County.—The Gulf Refining Co. drilled Davis No. I in sec. 2, T. 9 N., R. 9 W. in Wayne County. After several stem tests 545&apos;-in. casing was set at 6850 ft. and production was obtained in the so-called Massive Sand of the Lower Tuscaloosa. The well produced 359 bbl. of oil in 24 hr., and it Was completed on Oct. 4, 1943. Other locations have been staked ill this area and probably will be drilled in 1944 by

Jan 1, 1944

By W. M. Robertson

The formation of grain boundary grooves on surfaces of poly crystalline samples of cobalt and iron immersed in liquid lead has been studied. The grooves form by volume diffusion of the solutes cobalt and iron in the liquid. The diffusion coefficients of the solutes in liquid lead are derived from the measured rate of grooving. The diffusion coefficients are described by the relation D = Do exp (-Q/RT), with, for cobalt, Do = 4.6 x 10-4 sq cm per sec and Q = 5300 ± 800 cal per mole, and for iron, DO = 4.9 x 10-3 sq cm per sec and Q = 10,500 ± 1500 cal per mole. LIQUID metal-solid metal interactions occur at solid-liquid interfaces. Interfacial energy provides a driving force to change the morphology of the interface. Mullins1,2 has derived expressions for the kinetics of interface morphology changes driven by capillarity. These expressions can be applied to an isothermal system of a solid in equilibrium with a liquid saturated with the solid. Surface profile changes can occur by volume diffusion of the solute in the liquid, by volume self-diffusion in the solid, and by interfacial diffusion at the liquid-solid interface. A groove will form at the intersection of a grain boundary with a solid-liquid interface, reducing the total interfacial free energy of the system. The solid-liquid interfacial energy ? must be greater than half the grain boundary energy of the solid ?6 for Mullins&apos; calculations to apply. If ? is less than ?b/2, then the liquid penetrates the boundaries, separating the grains rather than forming grooves. Boundary penetration did not occur in the work described here. where CO is the equilibrium volume concentration of the solid in the liquid, Dv the volume diffusion coefficient of the solid in the liquid, ? the interfacial free energy of the solid-liquid interface, O the atomic volume of the solid crystal, k Boltzmann&apos;s constant and T the absolute temperature. Eqs. [1] and [2 ] also apply to grooving by volume self-diffusion in the solid,1 with CoODv = D Self, where DSelf is the volume self-diffusion coefficient of the solid. For a grooving mechanism of interfacial diffusion at the solid-liquid interface, the groove width is given by2 where CS is the interfacial concentration of the diffusing species, and DS is the interfacial diffusion coefficient. Eqs. [1] and [3] can be used to determine the mechanism of groove growth. A t1/3 dependence of the growth indicates volume diffusion and t1/4 indicates interfacial diffusion. In some cases, volume diffusion and interfacial diffusion both can contribute substantially to the grooving process, causing the time dependence to be intermediate between t 1/3 and t1/4.3 For these cases, the relative contributions of the two processes can be separated.4 However, in many cases, one process will be dominant, and the data can be analyzed on the basis of Eq. [1] or Eq. [3] alone. The time dependences for volume diffusion in a liquid and volume self-diffusion in a solid are the same. However, the self-diffusion contribution of the solid is usually negligible compared to volume diffusion in the liquid. After the grooving mechanism has been determined, Eq. [1] or Eq. [3 ] yields the kinetic parameter A or B. The kinetic parameter can be used to calculate values for the unknown quantities in the product CD?. Usually C is known or can be estimated. If ? is known, then D can be calculated. In a measurement of grain boundary grooving of copper in liquid lead,&apos; the time dependence indicated volume diffusion in the liquid. The quantities Co, Dv, and ? were obtained from the literature, giving excellent agreement between the observed values of A and the values calculated from Eq. [2 ].5 In a study of the grooving of several refractory metals in liquid tin and liquid silver, A1len6 educed that grooves formed by volume diffusion in the liquid. In a study of nickel in a nickel sulfide melt, Steidel, Li, and spencer7 found volume diffusion grooving kinetics. Both Dv and ? were unknown, so they could not obtain either one separately, though they did obtain a reasonable value for the temperature dependence of the product Dv ?. Several methods have been used to obtain surface profiles. It can be done by sectioning through the interface7 or by chemically removing the liquid from the solid surface after solidification of the liquid.6 However, if the liquid dewets the solid on removing the solid from the melt, then the interface can be observed directly. This method was used previously&apos; and was utilized also in the present study. EXPERIMENTAL PROCEDURE Lead of 99.999 pct purity was obtained from American Smelting and Refining Co. Cobalt sheet was obtained from Sherritt-Gordon Mines, Ltd., with a nominal purity of 99.9 pct, the principal impurities being nickel, iron, copper, carbon, and sulfur. The sheet was

Jan 1, 1969

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media&apos;. Experimental verification of these proper-ties in oil-wet media was obtained some time ago&apos;, and more recently, Perkins&apos;, employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date&apos;.".&apos;. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,&apos;.&apos; but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

"Located at Canyon Ferry on the Missouri River, 17 miles from Helena and 63 miles from Butte. River drainage area 15,570 sq. miles. Built in 1898.DAM: Rock-filled, wooden crib, 490' long and 39' feet at maximum head; also masonry core, earth bulk-head 300' long and granite masonry abutments.SPILLWAY: 473' long, crest elevation 3660.5; steel flashboard system 10' high.PENSTOCKS: 10 main penstocks, 12' diam., about 40' long, leading from canal to turbines, each supplying 1 pair turbines.WHEELS: 4 main center discharge, horizontal units, each 1 pr. of 42"" wheels made by Dayton Globe Iron Works, and 6 main units, each 1 pr. of 45"" wheels made by S. Morgan Smith Co., all 157 r. p. m., normal head 34', and direct coupled to generators.GENERATORS: 10 W. E. & M. Co., Kodak Type, revolving armature, 750 k-w., 157 r. p. m., 550 v., 3 phase, 60 cycle alternators.OPERATION: The plant has large water storage and can carry peak loads to 12,000 h-p. It is the central control station for the system."

Jan 1, 1913

Executive JOHN M. LOVEJOY, Chairman ERLE V. DAVELER G. B. WATERHOUSE WISER JUDSON WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUM, Chairman PAUL D. MERICA R. M. ROOSEVELT H. G. MOULTON, Consultant Admissions. RALPH M. ROOSEVELT, Chairman GEORGE D. BARRON, Vice-chairman JOHN L. CHRISTI PHILIP KRAFT W. A. SINSHEIMER

Jan 1, 1936

By Charles E. Wait

It is said by some that the occurrence of a deposit of sulphide of antimony in Southwestern Arkansas has been known for fifteen or twenty years. Whether or not such is the case I am not prepared to say, but I am not able to find any record of such a discovery, or any analysis of antimony ore obtained from that section, published at so early a period. The present discoveries, that seem to be attracting some attention, date back to the winter of 1873-74. At that time a vein of ore was found by Mr. Robert Wolf, in honor of whom the vein was named, and still is called, "the Wolf lode." At the time of the discovery the ore was unknown to the prospector, and its composition was not thoroughly understood in that locality until samples were sent to several analytical chemists, who pronounced it sulphide of antimony—stibnite. Since the discovery of this ore there have been three mines opened, and a number of interesting minerals of the antimonial series have been found. I have had an unusually good opportunity to collect specimens from these mines; and it is owing to the constant inquiry concerning the character of these ores that I have collected for publication the results of quite a number of analyses, sufficient I trust to clearly point out their composition. This is one of the few localities in the United States where antimony ore is found in workable quantities ; I say workable quantities, because two different shipments of ore have been made to English reduction works, and in both cases excellent returns were made. The discovery of these deposits will, it is hoped, give rise to a prosperous and remunerative industry at no distant day, and when fully developed they may yield ore in sufficient quantity to supply the regulus for the home demand, thus adding wealth not only to those interested, but also to the State of Arkansas. The three mines are situated in the northern part of Sevier County, and may be reached by the St. Louis, Iron Mountain and Southern Railway to Fulton, thence by wagon-road to Columbus, Nashville, Centre Point, and to the mines. During most seasons of the year the

Jan 1, 1880

By Khosrow Bakhtar

A series of nineteen shear tests were performed on fractures 1 m2 in area, generated in blocks of sandstone, granite, tuff, hydro- stone and concrete. The tests were conducted under quasi-static and dynamic loading conditions. A vertical stress assisted fracturing technique was developed to create the fractures through the large test blocks. Prior to testing, the fractured surface of each block was characterized using the Barton JRC-JCS concept. The results of characterization were used to generate the peak strength envelope for each fractured surface. Attempts were made to model the stress path based on the classical transformation equations which assumes a theoretical plane, elastic isotropic properties, and therefore no slip. However, this approach gave rise to a stress path passing above the strength envelope which is clearly unacceptable. The results of the experimental investigations indicated that actual stress path is affected by the dilatancy due to fracture roughness, as well as by the side friction imposed by the boundary conditions. By introducing the corrections due to the dilation and boundary conditions into the stress transformation equation, the fully corrected stress paths for predicting the strength of fractured blocks were obtained.

Jan 1, 1984