Search Documents

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By Howard A. Meyerhoff

IN western Argentina, in the Province of Mendoza and the Territory of Neuquén, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina's limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina's fuel problem. CHARACTER OF SOLID BITUMENS The solid bitumens of Mendoza and Neuquén are petroleum derivatives, as is indicated by the following ultimate analysis: [CONSTITUENTS PER CENT Hydrogen6.8 Carbon82.4 Nit.rogenI.6 Oxygen2.7 Sulphur2.2 Ash4.3 100.0] In physical appearance they bear a close resemblance to coal and are commonly called carbón. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-conchoidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquén. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens, are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Esperanza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1947

By J. Chipman, J. C. Fulton

Reduction of Si from slag to carbon-saturated iron is a very slow reaction. The rate is nearly independent of stirring but is accelerated markedly by increased temperature. In a slag containing 45 pct SiO2, 38 pct CaO, 17 pct Al2O3, the energy of activation is approximately 130 kcal. AT temperatures of 1450" to 1600°C occurring in the hearth of the iron blast furnace, chemical reactions are normally expected to proceed with great rapidity. Many of the reactions of iron making are indeed quite rapid and attain a condition corresponding roughly to a state of equilibrium before metal and slag are tapped from the furnace. The one conspicuous exception is the reaction by which carbon in the coke or metal reacts with silica in the slag to deliver silicon to the metal. From the practical viewpoint the slowness of this reaction is indeed fortunate, for if it were fast enough to reach equilibrium during the time of contact, it would be difficult to produce pig iron of the desired low silicon content. The one other reaction which under certain circumstances can also be very slow is the transfer of sulfur from blast-furnace metal to slag. In their laboratory exeriments on this reaction, Hatch and Chipman found that at least 5 hr were required for the attainment of equilibrium in a small crucible and that the reaction was not accelerated by increasing the rate of stirring. Subsequently it was shown2 that the presence of a reducible oxide MnO greatly inhibited sulfur removal, and finally that SiO2 itself3 under some conditions has sufficient oxidizing Dower to interfere with sulfur transfer. The kinetics of sulfur removal are now rather well understood,4 and it has been shown3,5 that when the silicon content of the metal is high enough to prevent reduction of SiO,, the desulfurizing process is rapid. Thus the observations of slow removal of sulfur are associated with the coincident slow reduction of SiO2, a process which transfers both silicon and oxygen to the metal phase. It is, of course, the oxygen which interferes with sulfur removal. An explanation of the slowness of the silica reduction reaction has not been obtained. The sulfur transfer process has been shown by the authors5 to be at least partially transport-controlled in the absence of interference by silica. Under the experimental conditions. 99 pct of the total transfer at 1600" was accomplished within an hour. Under similar conditions the reduction of silica may not proceed half-way to equilibrium6 in 8 hr. It is scarcely imaginable that silica reduction could be transport-controlled when the slag contains 44 pct SiO2 and the metal about 1.4 pct C. The experiments reported here show definitely that it is controlled by a slow step or steps in the chemical reaction. One might expect to find such a slow step in the breaking of SiO bonds or in the slow removal of oxygen by carbon at the slag-metal or metal-crucible interface or by bubble formation. EXPERIMENTAL PROCEDURE The experimental procedure used in this investigation was similar to that used in the study of the kinetics of desulfurization.5 A sketch of the graphite crucible and stirrer used in the current work is shown in Fig. 1. The quantity of metal and slag used was adjusted so that the slag-metal interface was located between the top and bottom blades on the stirrer; the top of the slag layer was above the top blade. The stirrer shaft was hollow down to the metal level and served as thermocouple well or optical pyrometer target. Stirring speeds of 0 to 500 rpm were used. A carbon monoxide atmosphere was maintained in the furnace by flushing the gas over the slag surface, except in run No. 220 when it was bubbled

Jan 1, 1960

AN extremely successful meeting, under the joint auspices of the Ohio Section and the Iron and Steel Committee, was held at Cleveland on April 19 and 20, about one-half of those in attendance being from the Cleveland district and the other half from a distance. The morning session on April 19, C. K. Leith presiding, was opened by the presentation of the ad-dress of which an excerpt is printed on the opposite page. In the subsequent discussion R. A. Allen pointed out that the meeting had not been called "to blow the lid off the tariff" since that is only one of the many problems connected with the wisest utilization of man-ganese, and it was the purpose of this meeting to con-sider all those interdependent problems. The purpose of the tariff was to develop an adequate domestic sup-ply, and that result had not been accomplished. An-other important problem, linked with the tariff, is the need for assuring, while we are at peace, an adequate war supply of manganese, and at present this country has no such policy. D. F. Hewett said that his 3-months' trip in Europe last summer had impressed him with the fact that England had once been in the position United States now is in, of being the principal world's producer of all the more important minerals and with a declining reserve had gone on a free-trade basis. No one pointed out that, with the exception of tin, the present relative position of England is due more to an increase in pro-duction in other countries, rather than to a decrease of domestic production. J. Sharshall Grasty referred to recent development work-in Virginia where of 30 per cent easily concen-trated manganese ore about 300,000 tons has been blocked out and possible and probable ore amounting to 700,000 tons more is indicated.

Jan 5, 1927

By D. L. Martin

The study of cobalt-platinum alloys has been of interest since they represent a class of permanent-magnet material in which the disorder-to-order transformation plays a controlling role. The magnetic properties of alloys in the range 40 to 60 at. pct have been found to be greatly influenced by composition and heat-treatment. The peak properties of 4700 coercive force and 9,000,000 gauss-oersteds energy product were obtained by controlled cooling and aging. These high values combined with ductility and machin-ability give the alloys useful characteristics although their high cost limits their application. THE cobalt-platinum alloys have been of interest in the study of permanent-magnet materials ever since the discovery by Jellinghaus that they had unusually high coerceive-force values.' The high coercive force was associated by Jellinghaus with the disorder-order reaction which occurred in these alloys. This was later verified by Gebhardt and Koster in a detailed study.2 An investigation of the structure, mechanism, and kinetics of the disorder-order transformation and resulting property changes in cobalt-platinum alloys has been in progress for some years. Certain phases of this study related to equilibrium rela- tions, and to the mechanism and kinetics of the ordering reaction have been published previously.3-5 In this paper, the results of the processing and heat-treatment studies on 40 to 60 at. pct CO alloys are presented. The magnetic properties have been found to be influenced greatly by the composition, by the cooling rate from the disordering treatment, and the final ordering time and temperature. Coercive force values, Hc, of 4700 oersteds and energy values, (BH)m, approaching 9,000,000 gauss-oersteds have been obtained by controlled cooling and ordering. PROCESSING OF THE ALLOYS The composition range of interest for permanent-magnet properties centers around the equiatomic composition Copt. In this region the alloys are dis-

Jan 1, 1959

I do not think too much emphasis can be placed upon creation of favorable climate for development of foreign mineral resources to feed the hungry maw of our industrialized nation. We have become dependent, not only upon the ten raw products indicated in Mr. Bancroft's article, but upon 71 mineral substances listed by DMPA as in short supply. Forty-four of these are metals, 9 are chemical minerals and 18 are nonmetallic minerals. Of this list only 8 are produced in any large quantity in the United States, and all are vital in peace-time industry. Even more, they are absolutely essential for defense. This represents our present needs. But if our consumption and requirements are projected over the next 25 years as is done by the President's Materials Policy Commission-The Paley Report-our future outlook becomes appalling. The divergence of consumption over production, even allowing for substitution and conservation, will widen in the future. This means our dependence upon foreign raw materials, mainly minerals, will grow. What are the chief foreign sources of minerals for our future needs? They are chiefly Latin America and the dominions and colonies of the Western European nations. The British Commonwealth countries contain in abundance those minerals which the U. S. lacks. Of 32 of the most critical minerals the Commonwealth is deficient in 7 and lacks only 1; whereas the U. S. is deficient in 18. Strikingly, our deficient minerals are abundant in the Commonwealth and several of their deficiencies are in excess in the U. S. Resources of the two nations complement each other. If Europe should be overrun by an unfriendly power that could control the destinies and resources of the European dominions and colonies, our industrial life would be placed in severe jeopardy. Therefore, I heartily endorse Mr. Bancroft's statements regarding the Point IV program, provided the program is wisely administered and implemented. It is from the underdeveloped countries, as pointed out by Mr. Bancroft, that most of our future mineral supplies will have to come. Many of the underdeveloped source countries are African colonies and dominions of Western European nations. Our present aid to Europe, therefore, is not, as many infer, a purely one-sided affair; it safeguards our future industrial development and security. Development aid directly to the underdeveloped countries through a well administered Point IV program, can do much, I believe, to safeguard our prosperity. I regard it as a wise investment for future U. S. mineral needs. Dr. Alan M. Bateman Department of Geological Sciences Yale University Mr. Howland Bancroft's article, The Broadening Road to Foreign Investment, appeared on page 666 of the July MINING ENGINEERING.

Jan 1, 1952

By Carl F. Cline, Richard R. Vandervoort, Willis L. Barmore

THE objective of this investigation was to determine the high-temperature plastic deformation behavior of stoichiometric uranium mononitride as a function of stress and temperature. Interest in the properties of this material stems from its potential use in high-temperature nuclear reactor systems. The creep of other refractory compounds containing uranium (e.g., U02, UC) has been studied by various investigators.1"4 Fassler et al.4 have studied the creep of UN in vacuum from 1100° to 1350°C at stresses of 6000 and 8000 psi. In the present work, the creep of stoichiometric UN was investigated from 1500° to 1800°C at stresses from 2000 to 5000 psi in a partial pressure of 200 mm of nitrogen. The specimens were prepared by hot isostatic pressing of UN powder into cylinders of $ in. diam by about 1 in. high. After pressing, the specimens were heat-treated in nitrogen at 1900°C for 50 hr. The densities of individual specimens were determined by the water displacement method. All specimens were theoretically dense, based on a value of 14.32 g per cu cm.5 Principal metallic impurities in ppm by weight were: Ca, 50; Cu, 5; Fe, 30; Mg, 5; Ni, 10; and Si, 20. Oxygen content was 400 ± 50 pprn and carbon content was 100 i25 ppm. The nitrogen content was 5.56 ±0.05 wt pct. The average grain size for five specimens, as determined by the intercept method, was 0.14 i 0.01 mm. One specimen had a grain size of 2.0 mm. This large grain size is an anomaly, since all specimens had the same chemical and thermal histories. Specimens of 1/4 in. diam by 1/2 in. high were creep-tested in compression in a clam shell furnace heated by W-25 pct Re sheet elements. Temperature was measured to ilODC by an optical pyrometer which had been calibrated by a standard source. The distance between fiducial marks on the specimen was measured before placement into the furnace. The furnace chamber was evacuated to 10-5 Torr and back-filled to 200 mm N2. After heating rapidly to temperature, the load was applied and controlled to ±2 pct by an Instron testing machine. Upon initial loading, the specimen was deformed until a constant crosshead rate was obtained, then quenched to room temperature, remeasured, and replaced in the furnace. Upon subsequent reloading at temperature, the crosshead rate was constant for the selected condition indicating steady-state creep.

Jan 1, 1969

Since 1571, when the Institute was founded, many of the most important papers in the English language, on the various phases of mining and metallurgy, have appeared as Institute publications. As members of the Institute regularly receive the publications in which they are interested, this discussion is primarily for nonmembers who wish to know of them. The Institute has several means of issuing papers which have been submitted and accepted. The monthly journal, Mining and Metallurgy, is the magazine of the Institute. In it appear notices and reports of official business as well as many papers and contributions which do not appear otherwise. The annual subscription price of the magazine to nonmembers is $3 per year; Canadian and foreign postage $1 extra; single copies 50 cents; back issues $1 each. Many papers are published separately each year. They are issued in one or the other of two numbered series; namely, Technical Publications and Contributions, and of the latter there are four forms: Preprints, Mimeographs, Reprints, and Unpublished Manuscripts. A Technical Publication or Contribution (in any form) is issued by the Institute when it is listed in Mining and Metallurgy. Technical Publications are sent automatically to members who have asked in advance for papers on a given subject. All members are entitled to a copy of every paper in either series, except when a Contribution is an Unpublished Manuscript. Con¬tributions in the form of Unpublished Manuscripts are filed in the Engineering Societies Library and copies of some of these papers may be found in a few selected libraries throughout the country.

Jan 1, 1933

By W. Rostoker, S. A. Spachner

FOLLOWING the discovery of the w transition phase in certain titanium-chromium alloys by Frost, Parris, Doig, and Schwartz, much interest has centered on the alloys in which this phase is found and its mode of precipitation. The w phase has been found in alloys of Ti-Cr, Ti-Fe, Ti-Mn, Ti-MO,2 and Ti-v.3 The temperature-time-transformation characteristics have, as yet, not been determined for most of these. In this study, such transformation characteristics have been investigated for two heat-treatable titanium alloys known to exhibit transition phase phenomena. The alloys chosen, Ti-8Cr and Ti-13M0, are representative of two classes of binary equilibrium systems. In the

Jan 1, 1959

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;' the direction and the driving force of grain boundary sliding and migration;' the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.' It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954

By V. S. Gupt, W. H. Somerton

Rock may undergo great changes in physical properties when heated to high temperatures and then cooled, The temperature and intensity of reactions causing rock alterntiorl.s can he controlled by introducing certain chemicals during heat treament. Three typical outcrop sandsone samples were saturuted with common salt solutions, then heated to several maximum temperatures. After cooling, it was found that per-rrreuhilities had increased much more for salt-saturated samples than for samples not saturated with salt but heated to the same temperatures. This was only true, however. for samples heated above the melting points of the particrrlar salts. Potassium chloritle was particularly effective with Bandera sandstone. Samples saturated with potassium chlorirlr. solution and heated to 900C showed an 11-fold increa.se in perrrieahility. Samples without potasrirdrn chloritle but heated to the .same temperature. showed only a 2.7-jold incresre in permecahility. In application, it seems possible that injecting chemicalc into the formations from a wellbore followed by applying intensive borehole heating might promote reactions which would greatly improve permeability of the formalions. INTRODUCTION Great changes in the physical properties of rocks which have been heated to temperatures in the range of 600 to 800C have been reported earlier. Permeability increases of 50 per cent, and equivalent decreases in sonic velocity and breaking strength have been observed. Although there might be some suppression of certain reactions responsiblc for these changes when rock samples are heated under simulated reservoir pressure conditions. recent work has shown that these are more than offset by the increased importance of other reactions at high pressures. The reactions considered responsible for alteration of rock properties by heating include differential thermal expansion. dehydration, phase changes and dissociation of mineral constituents. Ceramists have long known that temperatures at which reactions occur can be raised or lowered by the presence of certain impurities in the sys. tcnl. Thus the possibility exists that by saturating rocks with appropriate solutions. desired reactions might be accelerated and unwanted reactions might be suppressec! when the rock is heated. Purpose of the present work was to investigate the effects of several common salts on the thermal alteration of sandstones. Types of reactions which might occur are reviewed and the findings of a number of thernlochemical alteration tests are presented. THEKMOCHEMICAL ALTERATION OF SANDSTONE MINERALS The most abundant constituent of most sandstones is quartz. Quartz can exist in at least eight different forms, but in the temperature range of immediate interest (to 900C) only two forms are of importance—alpha quartz below 573C and beta quartz above this temperature. Although the alpha-beta inversion of quartz is very important in thermal alteration of rocks. it is not particularly important here because the inversion temperature cannot be changed significantly by the presence of impurities or by the application of pressure. The transition temperature of quartz to tridynlite is 867C. but the transition is very sluggish. Tridymite is considered to be a metastable transition phase between two stable phases: quartz?cristobalite. However. the transition temperature for tridymite to cristobalite is 1,470C.4 The quartz-tridymite-cristobalite transition can be accelerated substantially by the presence of fluxing agents. Finely divided calcium, magnesium and titanium oxides accelerate the conversion while A12O may retard it. A Mixture of NaCl and CsCl reduces the temperature for cristobalite formation by as much as 420°C. Feldspars constitute the second most important mineral in sandstones. The melting points of feldspars range between 1,000 and 1,700°C depending upon the variety. No information available indicated any important role of fluxing agents in the thermal alteration of this group of minerals. Carbonate minerals are subject to dissociation at temperatures within the range of the present investigation. The dissociation of magnesite can start at a temperature of 373°C, but the reaction is sluggish and might not occur untll a temperature of 500°C or ,higher is reached. Dolomite dissociates in two stages at 500°C and 890°C, whereas calcite dissociation temperature is about 885C. Because CO2 is released in the dissociation of carbonates, ail such reactions are somewhat dependent upon CO2 partial pressure. In the absence of CO: in the surrounding atmosphere, the dissociation of calcite starts at 500°C.However. when 1 atm of CO surrounds the sample, the dissociation does not start until 900C. The other carbonates are apparently much less sensitive to a change in partial pressure of CO2. The aragonite calcite transformation can occur an!. where within the temperature range of 357 to 488°C. depending upon the presence of impurities such as barium. strontium. lead and perhaps zinc. The differential thermal analysis (DTA) curves of both magnesitc and dolomite vary with the presence of 'impuritics. The presence of iron in particular seems to affect the magnesitc DTA curve

Jan 1, 1966

By W. J. O'CONNOR

THE production of lead in the United States for the period from 1720 to 1912 was 10,432,668 tons valued at $924,600,000. The average price during this period was 4.4c. a pound, although lead sold at times below 3 cents. We know that in the early days of lead smelting in Montana lead was deliberately lost in the slag and only enough reduced as bullion to collect the silver. This bullion was freighted by ox team to Corinne, Utah, the terminus of the railroad at that time, and shipped to Swansea or Omaha, Neb., for refining. The slag from some of the above mentioned operations contained as much as 15 per cent lead and has since been resmelted. Since 1921 the production of lead has increased each year and the price and tonnage have been as follows :

Jan 1, 1926

Although the 71 Minerals operation is now closed down and the operating data presented is almost five years old, it is well worth describing since it was the first heap leaching operation conducted on a primarily silver ore. Tombstone was discovered in 1877 by Ed Schieffelen; and it became one of the most famous mining towns in the West through the stories connected with Wyatt Earp, Doc Holliday, and the Clanton brothers. Like many silver deposits .in the western United States, the Tombstone ores were relatively shallow. Several million ounces of silver were recovered in the relatively few years the camp was active; but mining virtually ceased by the early 1900s and was only continued in a small way until the 19409, a history similar to that of Tuscarora. The 71 Minerals operation was started in May 1975 and continued until late 1978 within the city limits of Tombstone on waste dumps; one was the' Lucky Cuss, Schieffelen's discovery, which had accumulated from the old underground operations. This waste material was mostly less than 50 mm (2 in.) in size, although there was some larger lumps. The grade was about 34 g Ag and 0.5 g Au per mt (1.0 oz Ag and 0.015 oz Au per st). The Tombstone dumps contained approximately 1,000,000 tons. The dumps and patented claims were held by a single owner, Tombstone Development Company, thus sufficient leaching material could be acquired from one source rather than dealing with a number of individuals, as is usual in putting together leaching ventures in old mining camps. 71 Minerals Ltd. was formed and a lease of the properties obtained. A site was selected close to the major mine dumps not far from down- town Tombstone. Pads approximately 90 m (300 ft) wide and 180 m (600 ft) long with an 8-degree slope were prepared using compacted old mill tailings as a base sealant on the pads. Mining was done at a rate of about 2,000 tons per day with a dozer, two scrapers, a front-end loader, and 30 ton trucks. The ore was dumped by the scrapers as it came from the dumps with no screening or crushing in 460 mm (18 in. ) layers and trimmed with the loader. Based on bulk sampling and laboratory testing, the majority of thegold and silver values were recovered within 30 days of leaching.

Jan 1, 1981

By C. B. Jordan

LAVES and Wallbaum' have described TiRu and TiOs as having the same structure as TiFe; they had previously described the latter compound as having the CsCl structure. On the other hand, a careful investigation of the structure of TiFe by Duwez and Taylor- ailed to reveal the ordered CsCl structure, finding instead a random arrangement of titanium and iron atoms on the points of a body-centered-cubic space lattice. Consequently, it is not clear whether Laves and Wallbaum proposed the ordered or the disordered structure for TiRu and TiOs. In order to settle this question as to the structural type and to obtain values of the lattice para- meters (thereby completely determining the structures), the present investigation was undertaken. Samples having the compositions TiRu and TiOs were weighed out accurately from iodide titanium supplied by the New Jersey Zinc Co., ruthenium powder from Goldsmith Brothers Smelting & Refining Co., and osmium powder from Wildberg Brothers Smelting & Refining Co. No analysis was made of any of these metals. According to the respective analyses of the suppliers, total impurities amount to less than 0.03 pct in the titanium and to less than 0.5 pct in the osmium. The purity of the ruthenium is not known. The alloys were prepared by arc melting in a furnace of the type described by Schramm, Gordon, and Kaufmann.9 pecimens for X-ray diffraction were obtained by crushing the ingots and passing the resulting powders through a 200 mesh screen. Diffraction patterns were made with a powder

Jan 1, 1956

By Howard R. Hume, Terry R. West, William R. Judd

One of the outcomes of a sector slope design in a large open pit in the western United States has been the scrutiny of the structural domain concept. These domains essentially define the area of influence of particular structural characteristics. In the present instance these structural characteristics are joint discontinuities. One of the major drawbacks of defining a domain is that unless large quantities of discontinuity data are available this process of definition is largely qualitative in nature. Viewed from a discontinuity analysis aspect the orientations of all the major joint sets at a given point are a concise descriptor of the structural geologic regime at that location. This is important to domain boundary definition, this in turn is extremely important for assigning which joint sets to use as input for slope stability analysis in a given discontinuity domain. An attempt has been made to develop a quantitative method for defining these discontinuity domains based on limited amounts of orientation data thereby reducing the subjectivity normally involved in such operations. Subjectivity is not always a problem if large quantities of joint orientation data are available, since the mean and variance of joint clusters always can be compared and then grouped to define these domains. However, even this method suffers from the problem that only a single joint set orientation can be considered at a time during the grouping process. On the other hand a discontinuity domain requires that all joint sets at a point be considered simultaneously to truly define the structural discontinuity character of that point. This provides a far more complete

Jan 1, 1982

By A. D. Zunkel, A. H. Larson

Equilibrium arsenic contents of Pb-As alloys in contact with PbO-As2O3 slags containing less than 30 mol pct As2O3, were determined at 650°, 700: and 750 C in an inert at?rzosphere. In this temperature range, the arsenic content of the alloy increased with increasing temperature in the single-phase liquid slag region and decreased with increasing temperature in the two-phase slag region and the single-phase solid-solution slag region. The PbO-As2O3 phase diagram below 22 mol pct As2O3 was determined by thertrzal analysis and by application of a log ?As2O3/?PbO vS log XAs2o3 /x3pbO plot determined from the equilibrium actiuity data. The resulting phase diagram was not well-defined since the eutectic temperature was not detected in the thermal analysis experiments, although a region of terminal solid solubility of As2O3 was found. Results from the phase diagram determination are compared with an existing diagram in the literature. THIS experimental investigation is an extension of a study by the authors1 on the slag-metal equilibria in the systems concerned with commercial lead refining processes such as softening and dross fuming. The first part of this investigation was a study of the slag-metal equilibria in the Pb-PbO-Sb2O3 system. The only experimental work previously done on the Pb-PbO-As2O3 system was by Pelzel2,3 in which the phase diagram for the PbO-As2O3 system was determined below 50 wt pct As2O3 and the equilibrium constant for the reaction 3Pb + As2O3 + 3PbO + 2As was determined as a function of temperature. No slag-metal equilibrium data have been determined. It is due to the scarcity of information regarding the Pb-PbO-As203 system that this work was undertaken. This paper describes the determination of the slag-metal equilibria in the Pb-PbO-As203 system by equilibrating Pb-As alloys with PbO-As2O3 slags in an inert atmosphere, the effect of 1 wt pct additions of bismuth and copper on the slag-metal equilibria, and the PbO-As2O3 phase diagram both by thermal analysis and the use of the slag-metal equilibria data. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade and assayed as follows: 1) 99.8 pct PbO (0.014 pct insoluble in CHJCOOH, 0.02 pct not precipitated by H2S, 0.1 pct CaO, and 0.08 pct SiO2); 2) 99.95 pct As2O3; 3) 99.99 pct Pb; 4) 99.0 pct As; 5) 99.99 pct Cu; and 6) 99.97 pct Bi. Room-temperature X-ray patterns revealed no detectable impurities in any of these materials. Apparatus for Equilibrium and Thermal-Analysis Determinations. The resistance-heated crucible furnace used in this investigation employed nichrome elements and was mounted so that it could be raised to surround the reaction tube during each experiment and, subsequently, lowered. A schematic diagram of the apparatus is shown in Fig. 1. Each charge was heated in a 3+-in.-OD by 31/2-in.-high 416 stainless-steel crucible placed in a 41/4-in.-1D by 18-in.-long fused-silica reaction tube which was closed at one end. On a shoulder around the crucible was placed a 3: -in.-OD by 12-in.-long open-end fused-silica condenser tube. The open end of the reaction tube was covered by a water-cooled brass cap with ports for 1) admitting an inert atmosphere to the system through a stopcock, 2) introducing a stainless-steel, motor-driven, paddle stirrer into the crucible, 3) evacuating the system with a mechanical vacuum pump, and 4) sampling the melt with Vycor sampling tubes. The brass cap was fitted to the open end of the reaction tube with a silicone gasket and collar clamp. The furnace temperature was controlled by a Barber-Coleman Capacitrol controller and a chromel-alumel thermocouple. Due to the corrosiveness of the melt, the controlling thermocouple also served as the measuring thermocouple. The temperature of the melt was calibrated against the controller temperature and was checked periodically during each test with a Vycor-enclosed calibrated chromel-alumel thermocouple. The temperature measurement and control can be considered accurate to ±3°C. Procedure. The charge placed in the crucible for each experiment consisted of 1000 g of Pb-As alloy and 300 g of PbO-As2O3 slag. The crucible was then placed in the reaction tube, the condenser tube was placed on the shoulder of the crucible, the silicone gasket and brass cap were fitted on the open end of the reaction tube, and the entire system was evacuated and filled with argon ten times. After the last flushing, a positive argon pressure of 1 psig was impressed on the system. The furnace was then raised to sur-

Jan 1, 1968

By J. Cervik, P. C. Thakur, S. D. Lauer

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh coal seam in northern West Virginia under USBM Cooperative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of 14 small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by a surface exhaust fan. The methane capture ratio was poor at 7% to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance, the boreholes should be drilled from a point 30 to 45 m (98 to 148 ft) from longwall pillar over the largest chain pillar. The standpipe should be grouted for at least 6 m (20 ft), and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane migration toward cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45º ± 10º.

Jan 1, 1986

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942