Search Documents

By Roy A. Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced', at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces'. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By P. S. Kotval

THE nominal composition of "hconel" alloy 718 is 53 pct Ni-19 pct Cr-19 pct Fe-3 pct Mo-5 pct Cb-0.8 pct Ti-0.6 pct A1-0.05 pct C. The nature of the fine strengthening phase in this alloy has been open to debate. iseelstein' has identified the strengthening phase in the matrix of "Inconel" alloy 718 as a colum-bium-rich fcc y' precipitate. Wagner and Hall2 have noted that the metastable y' precipitate overages to an orthorhombic Ni3Cb precipitate which manifests itself as an acicular phase. These authors thus clarify Kaufman and Palty's earlier suggestion3 that the strengthening phase is orthorhombic NisCb. Wagner and Hall's review also reports work by cometto4 which suggests that the fine strengthening phase is not fcc / but bct with a Ni3V type structure and based on the Ni3Cb composition. Kir man and warringtons have shown by analysis of electron diffraction patterns that the metastable strengthening phase in a 55 pct Ni-15 pct 0-25 pct Fe-5 pct Cb alloy is bct and based on the Ni3Cb composition. Raymond~ has provided electron diffraction evidence which indicates that "y'" in "Inconel" alloy 718 is bct in structure. This note presents unambiguous data on the structure of the strengthening phase in "Inconel" alloy 718* ihe samples of this alloy were provided by courtesy of the ASTM task group on phase identification in 'superalloys. after prolonged aging. The electron diffraction patterns presented show that strengthening phase is not y' but bct as was proposed by cometto,' supported by Raymond,~ and identified by Kirman and warringtons in a similar system. Fig. 1 shows a selected-area diffraction pattern taken from a thin foil of "Inconel" alloy 718. The sample had received a final aging treatment of 1118 hr at 1200°F to precipitate the strengthening phase in the matrix. Fig. 2 is a schematic representation of the features in the diffraction pattern. The matrix orientation is (0i2)~,, as is shown by the indexed zone in Fig. 3. Figs. 4, 5, and 6 illustrate that the pattern, Fig. 1, is composed of three bct zones, viz., (0i4), (2i0), and (i01), respectively. These three zones correspond, respectively, to the alignment of the c axis of the bct unit cell with the [001], [loo], and [OlO] directions of the fcc matrix and serve to illustrate the fully coherent relationship of the precipitate structure with the matrix. The streaking of certain reflections is also consistent with the above orientation relationship. The interpretation of the diffraction effects presented here shows the metastable strengthening precipitate in "Inconel" 718 alloy to be bct in structure and demonstrates that it is not an ordered fcc y' phase.

Jan 1, 1969

By Paul A. Beck

It is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation. the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and " consume " the deformed hard material. The extent of stability attainable through recovery is limited, especially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or polycrystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "istraight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals—a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By Edwin B. Eckel

THIS paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy's collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore, the Siele, the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 pct and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper.

Jan 1, 1947

By P. W. Guild

DURING 1956 the application of geology and related scientific disciplines to the search for new mineral deposits went forward on an ever widening front. Spurred on by record-breaking consumption of many of the established commodities and new uses for minerals and metals that were hardly known a few years ago, the profession is figuratively leaving no stone unturned in the effort to insure that adequate raw material supplies will be avail- able for the future. More money was spent and more people were engaged along more lines of research than ever before. A huge project to map much of the Canadian Shield area by photogeologic methods stands at one extreme; application of isotope ratios to ore finding stands at the other; between them the more traditional techniques are being increasingly refined. In the Fiftieth Anniversary volume of Economic Geology, published late in 1955, Alan Bateman sketches the development of fundamental concepts as recorded in the pages of the journal over the first five decades. An additional 24 review articles cover individual aspects of the field and constitute a base for further advances.

Jan 2, 1957

By Calvin Pierson, R. S. Dean, E. P. Barrett

MANY studies have been made of the properties of steel produced by adding varying amounts of sponge iron to the charges used in steelmaking furnaces.1-3 The results of these previous studies, however, have failed to disclose a reason for the belief of steelmakers that steel made in this way is definitely different from steel made entirely from scrap or iron melting stock. This paper deals chiefly with the structure of the sponge iron, of the wrought iron made by welding the sponge iron into blooms, and of the steel made by melting the forged and rolled blooms. It is believed that the structure of the final steel is inherited from the ore and that this inherited structure produces marked differences in the properties of the steel and explains the feeling of steelmakers which is based on their experience. Three kinds of sponge iron were used in this investigation: One made from a limonite ore reduced with natural gas, one made from a hematite ore reduced with natural gas, and one made from a magnetite ore reduced with charcoal. The sponge iron made by reduction with natural gas

Jan 1, 1935

By Donald A. Cumming

Since the first major mine development, the company has continually looked for ways of improving drifting methods. The planned increase in production to 60,000 tpd, and the lack of trained personnel, requires new development methods to maintain this high production rate. In order to finish the drifting on the 2015 and 2075 levels, a total of 59,000 ft is required, or two years at the present rate.

Jan 4, 1972

By H. H. Hausner, H. S. Kalish

M. Hansen—This paper certainly is an interesting study. Although I have not had too much experience in the powder metallurgical methods of studying phase equilibria, I would like to say the following concerning the interpretations of the results obtained: 1. The existence of a zirconium-rich eutectic having a melting point close to 950°C and containing approximately 5 pct beryllium is well established. 2. Undoubtedly sintering of the original compacts (i.e., without repressing and resintering at 1350°C) resulted in a condition being far from equilibrium, even in the low-melting point zircon-rich region where undissolved zirconium particles have been observed. This means that only partial reaction between the component powders has taken place. 3. In preparing and handling powder mixtures for pressing and sintering, we have found that with powders differing considerably in density, and also in particle size, separation in layers of different composition may occur. This means that a concentration gradient would exist within such samples. This phenomenon may, at least to some extent, account for the difference in microstructure of the top and bottom regions of some of the sintered samples. If this is the case, density figures for some of the nominal compositions would not represent actual densities of those mixtures. 4. Fig. 1 shows that the low densities of mixtures with 40 and 60 pct beryllium sintered at 1350°C are changed to much higher densities if the products sintered at 1100°C are repressed and resintered at 1350°C, whereby an approach toward equilibrium takes place. This would mean that the low density and growth in volume is due to nonequilibrium conditions. If this is true, would it be justified, then, to conclude that "the remarkable growth of the alloys in the vicinity of 40 to 60 pct Be indicates the formation of a high-melting point phase, probably accompanied by a considerable change in volume due to a large alteration of the crystal structure from that of the original compounds"? If some compound formation has taken place already during the first sintering at 950" to 1350°C, more compound would be formed by repressing and re-sintering of the 1100" samples. This treatment, however, results in higher, rather than lower, densities. In general, the density-composition curve of alloy systems containing one or more intermediate phases is characterized by a more or less defined contraction (decrease in specific volume, increase in density) over the "theoretical" density. Does not discrepancy exist between the two statements that "growth of the alloy indicates the formation of a high-melting phase . . ." and "even at 1350°C, no indications of sintering have been observed"? 5. I am not sure that the explanation given for the fact that fig. 4 did not reveal as much eutectic as the top portions of the mixture with 2 pct Be, is correct. The density of the melt containing only 5 pct Be or even perhaps less, is not too much different from that of the nominal composition. The reason might be also that there was already some separation of the components in the pressed compact. 6. I do not understand why the microstructure of the bottom regions of the compact with 5 pct Be (fig. 6) is so different from that of the top regions (fig. 5). The compact was melted on sintering at 1100°C. Its composition lies close to the eutectic point. There should be at least some lamellar structure in the bottom regions too; otherwise, the composition of top and bottom must have been very different after sintering, because the eutectic is said to extend as far as the composition ZrBe2. In case the white and gray areas of fig. 6 are both gamma, and the black areas undissolved zirconium, this composition would be close to the phase coexisting with zirconium, that is, ZrBe2, according to the hypothetical diagram, or a compound richer in zirconium. 7. Figs. 9 and 10 are not mentioned in the text. 8. The great difference in microstructure of the composition 20 pct Be of figs. 8 and 14 on one side and fig. 15 on the other side proves that sintering at 950" and 1100°C results only in partial reaction of the powers. 9. The mixture with 60 pct Be (fig. 19) seems to consist of two phases, rather than one phase, one interspersed in a matrix of another. 10. The statement that the eta phase "may be an intermetallic compound or the product of a peritectic or monotectic reaction" seems to be misleading, because the product of a peritectic or monotectic reaction in this region of the system must be an intermetallic compound. 11. If there is some solid solubility of Be in alpha and beta-Zr, it would be expected to be higher in beta-Zr (b.c.c.) than in alpha-Zr (h.c.p.). The temperature of the polymorphic transformation of zirconium then would be lowered, rather than increased. In accordance with this, Battelle has found that the transformation point of titanium is decreased by beryllium. 12. In case the phases present in alloys with 80, 90, and 95 pct Be are identical (which appears to be correct), it is striking that the relative amounts of both phases (eta and beryllium) are not too different within this wide range of composition. With 60 to 65 pct Be

Jan 1, 1951

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By N. Nemeth, L. L. Sirois

The role of the filter medium in continuous-vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and filter cloth are discussed. Due to negative pressure differential, gas bubbles evolve in the slurry, constrict passages in the filter cake and medium, and further restrict flow through the tortuous channels. Filtration is a liquid-solid separation process taking place at a porous medium under a pressure differential. The liquid passes through the medium; the solids are retained on the medium as a partially dewatered cake. Filtration is far from a simple process and has been described in terms ranging from "complex" to "subtle." Because of the many variables involved, no unified filtration theory has been developed, and the filtration process is still considered very much an art. In industrial filter design, basic relationships, whether derived for idealized conditions or developed empirically, are usually adapted to suit local conditions. In the mining industry where continuous-vacuum filtration is the main dewatering process, the physical state of the concentrates and the relatively low pressure differentials permit the assumption that the cakes are noncompressible, an assumption which leads to the use of theoretically sound rate equations. Notwithstanding this simplification, there are other problems, unique in the application of vacuum to dewatering, and until now completely ignored, which demand special attention. The basics of filtration involve the capture of solids on, while permitting the flow of liquid through, a porous layer of cake and cloth. Flow is determined by the structure of the solids which make up the cake and the particles permanently attached to the cloth. The problem of this structure, essentially one of solid geometry, has been considered insoluble by Hatscheckl as early as 1907 and by Freshwater as recently as 1967. Since cake structure is determined by the slurry parameters, that problem is far too large for inclusion in this study. For theoretical considerations, uniform buildup of the filter cake must be assumed; and for efficient practical operation, the resistance of the medium must be kept constant over long periods. The latter can be achieved by careful selection of the filter cloth, since the greatest part of the total filtration resistance will develop at the cake-cloth contact. This paper discusses the role of the filter medium in continuous vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and the filter cloth.

Jan 1, 1971

By A. M. Lovelace

Introduction One area of engineering utilization of materials in which the requirements are especially rigorous and demanding is that of aerospace systems, including aircraft, helicopters, missiles, and space satellites. Materials used in these systems must reliably perform many critical functions in a broad range of adverse environments. Some of the most critical functions are performed by polymeric nonmetallic materials such as elastomers (rubber), coatings, fibrous materials, and reinforced plastics. These types of polymeric materials have some common characteristics that make them attractive to aerospace system designers: light weight, corrosion resistance, and relative ease and low cost of processing and fabrication. Each type also has its own special characteristics that enable it to perform certain required functions better than other competing materials can (Table 1). The desirable properties of polymeric materials, which in some applications make them the only practical candidates, are partly offset by their principal limitation, which is degradation by exposure to high temperature. [ ]

Jan 1, 1971

By AIME AIME

THE week, of April 5 will long be remembered by those that attended the Birmingham meetings of the Open-Hearth and Blast Furnace committees of the A.I.M.E. Iron and Steel Division. Birmingham iron and steel own received the 450 delegates with open arms; described and discussed their southern metallurgical practices and problems and compared experiences with their northern brother metallurgists in two days of technical sessions on Wednes-

Jan 1, 1937

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By AIME

IN the parlance of Hollywood, it was a super-colossal meeting. In the more restrained language of engineers, the Institute's 75th Anniversary Celebration attracted the largest crowd ever; was the longest Annual Meeting ever held, occupying a full week; had more important papers, more important people, more of an international flavor, and more glamour than ever before. And in the minds of those who came to the big city from the wide open spaces, one other record should be mentioned: for those not on an expense account, it was the most expensive affair ever staged by the Institute! To state the attendance down to the last digit for a meeting such as this is impossible. The total names registered on cards, plus those who attended the Annual Banquet but were not otherwise registered, came to 3149. But a few were registered twice, and probably a still larger few did not register at all, but just dropped in for a session or two in which they were interested. It would appear that 3200 would be about as close an estimate of attendance as could be made, and that is some 300 more than came to the biggest Annual Meeting of the past-in 1944. A considerable number of members brought their wives, but most were delegates at large.

Jan 1, 1947

By J. A. Ede

THE object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby, shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. H. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mines of the Illinois Zinc Co.

Jan 9, 1919

By J. Kostuik, M. J. de Bastiani

The method of mining the uranium orebody at Denison mine in the Elliot Lake district of Ontario is discussed. Details of the development of haulage-ways and rooms are giuen, as well as methods of ore haulage. The milling and beneficiation stages are noted briefly. Located in the Elliot Lake mining district of Canada, the Denison mine lies between Sudbury to the east and Sault Ste. Marie to the west, Fig. 1. This area is overlain by Huronian sediments filling a basin in the Keewatin basement complex. Subsequent folding of these sediments developed a synclinal structure, known locally as the Quirke Lake Trough, which forms the northern portion of the now famous big Z structure, the geological trademark of this region. Plunging to the west and extending nine miles from the granite outcropping in the north to the Keewatin lava contact to the south, the syncline has dips of 10" to 45" on the north limb and 10" to 20" on the south limb, Fig. 2. The Denison orebody, located on the north limb of the syncline, lies between 800 and 3000 ft below the surface. The main ore zone is within 50 ft of the Missisagi-Keewatin contact (see Fig. 3), and it varies in thickness from 6 to 32 ft. This ore zone has a composite dip of 19" to the south and is composed primarily of two pyritized conglomerate beds separated by a band of pebbly quartzite stratum. The upper conglomerate bed of the main zone varies from 2 to 15 ft in thickness, while the lower conglomerate varies from 2 to 12 ft. Over extended areas, mining is carried out over the entire section comprising the two conglomerate layers and intercalated quartzite; in other areas, the conglomerates are selectively mined, depending on the thickness of the quartz-ite. The ore zone contains approximately 6 pct sulfides and 80 pct silica. The predominant uranium-bear ing minerals are brannerite, uraninite, and an unidentified mineral (probably thucolite). Some of the uneconomic metallic minerals identified to date are pyrite, pyrrhotite, and chalcopyrite. MINE LAYOUT Shafts: Underground exploration and development (Fig. 4) were performed through two shafts 1/2 mile apart. The No. 1 shaft, sunk to a depth of 1856 ft with the main station established at the 1600-ft ore level, is a 250-sq ft, 5-compartment shaft capable of handling 4500 tpd. Two 5x5-1/2-ft compartments serviced by a 12-ft diam double-drum hoist, are used for hoisting 190-cu-ft bottom-dump skips in balance. A 30-man cage, offset by a counterbalance, operates within a 5-1/2x11-1/2-ft compartment. The fifth compartment is used as a manway, pipe, and cable-way. This shaft is also provided with an intermediate pumping station used during the initial mining phase as well as loading-pocket and spill-pocket installations and pumping facilities. The 480-sq ft No. 2 shaft, located down-dip from No. 1 shaft, has a 2776-ft depth. Serving as the main hoisting shaft with a maximum capacity of 9000 tpd, it has eight compartments, four of which are used for hoisting ore in 10-ton capacity bottom-dump skips. These four compartments, measuring 5x6-ft in section, are serviced by two 12-ft diam double-drum semi-automatic hoists. A 50-man cage is operated in a 15x8-ft compartment, and it is counterbalanced by a 12-ton weight. Two compartments are used for ventilation, manway, electric cables, and pipes. A station was constructed at the 1325-ft horizon of the No. 2 shaft for relay pumping. The main sta-

Jan 1, 1961

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942