Search Documents

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By Lawrence Wright

THE occurrence of gold, gold-silver, silver-lead-zinc ores in the post-Cambrian sediments in the Black Hills of South Dakota, and their genetic relationship to the Tertiary intrusives, is well known and accepted, but the occurrence of gold in the pre-Cambrian rocks at the Homestake mine, which underlie this Tertiary gold mineralization, has given rise to differ-ences of opinion as to the period of major gold introduction into the older rocks. Fig. 1 illustrates. the distribution of mineralization along the axis of the Tertiary uplift in both pre-Cambrian and post-Cambrian rocks. The following possibilities have been presented: 1. The Homestake gold deposit was formed in pre-Cambrian time and the deposits in the overlying Cambrian sediments formed during Ter-tiary time. 2. The Homestake lode existed at the beginning of Cambrian time, but was enriched by the passage of Tertiary auriferous solutions. 3. The Homestake lode was represented by pre-Cambrian quartz-chlorite sulfide mineralization, very low in gold content and the gold superimposed on the older nearly barren mineralization during the Ter-tiary metallogenic epoch. 4. The sulfides and sulfarsenides as well as gold were deposited in both pre-Cambrian and post-Cambrian rocks during the Tertiary period. Those favoring the first proposition feel that the question is pretty well settled, while the proponents of the second theory are more flexible in their view, feeling that the amount of gold introduced in either period is still an open question. The third and fourth theories, with some modifi-cations, are supported by the proponents of the Tertiary theory, who feel that the evidence strongly favors that period. The following pages are intended to present the evidence and to give the reaction of various observers with my own comments and conclu-sions; also, the accumulated facts of observation gathered over a period of close association with the area under discussion, beginning in 1919.

Jan 1, 1936

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

The Hurghada field is still the major producing field in Egypt. There was almost no activity in the Abu Durba field during 1936 and no new evidence is available. The following table summarizes the information on the Hurghada field for the year 1936. Hurghada Field Age of field to end of 1936, years.................... 23 Producing area for gas and oil, acres................. 1,050 Barbels Total oil production to end of 1936.................. 29,046,572 Total oil production during 1935.................... 1,212,182 Total oil production during 1936.................... 1,218,708 Daily average during November, 1936............... 3,249 MillionB CU. Ft. Total gas production (Aug. 1925 to end of 1936)...... 3,966 Total gas production during 1935................... 278 Total gas production during 1936................... 280 Maximum daily in 1936............................ 0.9 Number of producing wells completed to end of 1936... 94 Number of producing wells completed during 1936. ... 3 Number of wells abandoned during 1936............. 3 Producing wells at end of 1936...................... 768 Average depth of bottom of producing wells, ft....... 1,720 Average depth of top of producing horizon, ft......... 1,598 Character of oil, approx. average during 1936: Gravity at 60' F., 0.900; base mixed. Character of gas, approx. average during 1936: gallons gasoline per 1,000 CU. ft., 6.2. Producing rock (main): Nubian sands, Cretaceous; character, sand rock and sandy shales. 1 The figures given by the author were in tons. A conversion factor of 6.98. based on 0.900 sp. gr., was used to obtain the number of barrels.—Ed. 2 All pumping.

Jan 1, 1937

PRECEDING chapters on thermochemistry, and the reactions in and between metal and slag phases in the bath of the furnace tend to emphasize the equilibrium or "static" conditions in the furnace and process, such as the total amounts of heat from fuel combustion or from certain bath reactions, the concentration relationships between slag and metal at the steady state for certain reactions, and the like. Such data are obtained essentially by means of the logic of thermo- dynamics, which helps to determine the energy change between initial and final states in a process as well as to define its equilibrium or steady-state condition, but which is not concerned with the rate of change in the process or with the mechanisms or path followed between initial and final states. These questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling intelligently its operation, and also to understand certain natural limitations which are especially important in many high-temperature processes. The kinetic aspects of interest here comprise mainly (1) the flow of gases through the furnace system, (2) the flow of heat in the system, and (3) the mechanisms and rate factors in the various chemical reactions. A really adequate discussion of the first two subjects would require at least three or four times the space available here; it has been tried, therefore, in this and the next chapter to outline but a few fundamentals necessary to an intelligent approach and to indicate some of the conditions of heat and gas flow more or less peculiar to the open hearth, since several good general discussions on these subjects may be found in the literature.(1) For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance.(2,3,4,5) They are also important to the operation of the process, however, at least to the extent of a general qualitative picture of the movement of gases in the system, which is all that is attempted here.

Jan 1, 1944

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By J. A. Berger, R. J. Towner

A method for determining the disorientation between sub-grains that .share a common tilt or twist boundary from measurements on X-ray micrographs is described. The method may be applied to subgrains of almost any orientation having boundary angles in the range from about 1 min to 1 deg of arc. An adaption of the Berg-Barretl method has been made to allow calculation of small angles of about 1 min to 1 deg of arc: between adjacent subgrains from the relative displacement of their images on X-ray micrographs. schulz4 gave equations for determining subgrain disorientation where the axis of subgrain rotation and the reflecting crystal planes were parallel to the specimen surface. In our method, however, they need not be parallel and, indeed, may have va:rious orientations. His camera setup, involving a fine-focus X-ray tube for obtaining high resolution with continuous radiation, was different from the one used in the present investigation (a 1.2 x 1.2 mm effective source and characteristic radiation). The X-rays produced a slight magnification in the subgrain images in the Schulz method, but not in the present method. The commonly available type of X-ray tube used permitted relatively short exposure times with a fine-grained photographic plate, which could be magnified optically many times for the examination of small subgrains. The method is illustrated by results obtained on {110} tilt boundaries in a polygonized aluminum single crystal of 99.994 pct purity. The flat crystal was stretched 6 pct in tension and then heated at 500°C for a cumulative time of 5 hr. Earlier, cahn5 studied subgrains formed by polygonization in stretched and heated aluminum crystals. He observed kink bands to have well defined boundaries lying in (110) planes, at least in the early stages of deformation. Cahn found that the (110) tilt boundaries formed by polygonization were directly related to the lattice bending about the <211> axis which lay in the (111) slip plane perpendicular to the <110> slip direction. DESCRIPTION OF THE CAMERA Our camera was similar in detail to Honey-combe&apos;s.6 Unfiltered copper radiation was used at 35 kv, and 20 ma. With the particular specimen used here to illustrate the method, a 1.2 by 1.2 mm effective source and a distance of 780 mm from target to specimen were employed, giving a convergence of 5 min of arc in the primary beam. The distance was 9.5 mm from the specimen to film. The upper 1/2- by 1-in. portion of the front surface of the specimen was irradiated with the film in parallel position. Since the specimen had been inhomogeneously deformed, many regions were in a position to reflect characteristic radiation at the Bragg Angle. Five minute exposures were satisfactory with Kodak Single Coated X-ray Film, 1 1/2 hr

Jan 1, 1961

By F. Wartenweiler

Much has been written on milling and cyanidation as practiced on this gold field, therefore the purpose of this paper is to record its development only briefly and to describe in more detail the contemporary state of the science and art of this branch of metallurgy. It is a pleasing task, because a steady evolution is to be recorded. Definite trends influenced the development. Some have the stamp of original thought and observation; many have been achieved from a logical sequence of planned experimentation and research; while others have resulted from the drive of sheer necessity. The large scale of operations and capital outlay has compelled conservative progress. Banket ORe For a better understanding, a review of the characteristics of the ore may not be out of place. The Witwatersrand gold ore is named "banket" from the similarity of the oxidized outcrop ore to the Boer almond cake of that name. The inter bedded orebody is commonly called "reef." It is a conglomerate composed of various sizes of pebbles, principally non-gold-bearing white quartz, which constitute about 70 per cent of the bulk, within a matrix of cementing material consisting of fine-grained quartz, sericite, chlorite and chloritoid and containing the precious metals and mineral sulfides. Argillaceous components in the mil pulp may be as high as 32 per cent. Of the sulfide minerals, pyrite and pyrrhotite are predominant. Most base-metal sulfides are present, but sporadically and generally only found in highly concentrated mill products. In the latter, osmiridium is recovered in varying amounts; from 1 oz. in 3000 tons to 1 oz. in 10,000 tons of ore. Most of the oxidized ore has been mined, so milling is confined principally to the sulfide ore. A typical analysis of sulfide ore is: silica (SiO2), 86.76 per cent; pyritc (FeS2), 2.75; ferric oxide (Fe2o3), 2.65; alumina (Al2o3), 6.91; lime (CaO), tr.; magnesia (MgO), 0.70; sp. gr., 2.7. Milling grade at present price of gold (137 shillings per ounce) varies from 3.5 to 8.5 dwt., with one mine milling ore as high as 16 dwt. The

Jan 1, 1935

By T. M. Olson, B. G. Lewis

The adsorption of selenite on bentonite, kaolinite, and an iron--coated illite was studied to determine the importance of several soil variables on selenite removal from uranium mill tailings pond seepage. Adsorption capacities of the clays of selenite varied by orders of magnitude and decreased in the following order: illite > kaolinite > bentonite. Maximum adsorption of selenite on the clays was observed between pH 2.5 and the clay&apos;s zero-point-of-charge. Substantially less selenite was adsorbed on these clays in actual mill tailings solutions than in model systems. Virtually all selenite was removed from the tailings at pH 7. The principal removal mechanism at this pH is suggested to be the adsorption of selenite on freshly precipitated metal hydroxides. It is concluded that selenite can be removed from tailings seepage in soil or in clay liners in the presence of kaolinitic clays and iron oxides. Selenite would also tend to be removed from tailings seepage in calcareous strata.

Jan 1, 1984

By F. C. Schora, H. P. Meissner

Iron ore from Cerro Bolivar, Segre&apos;, and Sierre Grande was reduced in fluid beds at about SOOT, using gas analyzing 20.5 pct CO, 41 pct Hz, and 38.5 pct N2. Except in the early stages of reduction, the rate of oxygen loss from the bed was directly proportional to the oxygen concentration in the bed, independent of gas composition as long as the gas was reducing, and little affected by temperature. The percentage reduction of the bed solids at any time was independent of particle size. I HE reduction of spheres or cubes of dense iron ore in a slowly moving stream of either pure H, or pure CO has been found to take place at distinct interfaces between well defined layers of iron and the iron oxides.&apos;y4 These interfaces generally penetrate the ore lump in topochemical fashion, remaining parallel to the original contours of the specimen. Thus in the earlier stages of reducing hematite, the specimen&apos;s core is Fe,O, surrounded by successive shells of the lower oxides, and finally by an exterior shell of iron. McKewan5 assumed that the rate limiting step occurred at the Fe-FeO interface, with reducing gas penetrating up to this interface through the external porous iron shell, and reduction of the higher oxides within the ore lump occurring by diffusion of iron through the dense FeO shell. He developed an analytical expression based on this model relating the amount of oxygen removed from

Jan 1, 1962

By C. A. Heiland

For a long time it has been known that it is possible to deduce conclusions about the physical constitution of the interior of the earth from the records of natural earthquakes obtained by stationary seismographs. In view of this fact it is surprising how late, relatively speaking, geologic prospecting by seismic methods has been taken up, although the first suggestion was made 40 years ago—that travel-time curves of artificial explosions might be used for the study of the change of the velocity of seismic waves as depth. Further suggestions of practical applications of artificial explosions for geologic purposes were made by Belar12 by von dem Borne,3 by Benndorf and by Galitzin,5 but it was not .until 1919 that Mintrop obtained a patent on the seismic prospecting method which he has applied commercially on a large scale ever since. Dr. Mintrop came to this country with his method at about 1923. Since that time, several American oil companies have developed seismographs of the mechanical type for the vertical component similar to that of Mintrop&apos;s (Humble Oil Co., Dr. Ricker). Other consulting geophysical companies designed other types of seismic devices, the simplest of them for the recording of the first impulse being the geophone (McCol-lum Geophone Co.). The galvanometric recording method as first proposed by Galitzin is being used (Geophysical Research Corpn.?) and use is being made even of the piezoelectric properties of crystals for portable seismographs (F. Rieber). There is such an enormous variety of all kinds of portable seismographs, vibrographs, accelerographs, etc., that it is difficult to decide just what kind is preferable. Unfortunately, nothing has been published as yet about American designs of portable seismographs, except the Wood-Anderson torsion-seismometer. After Mintrop&apos;s design of portable seismographs, other constructions were made

Jan 1, 1929

By R. H. Hawkins

An investigation of the applicability of geophyiical methods to northern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines Pre-Cambrian ... Syenite, granite gnciss, etc. Igneous intrusivcs . Lamprophyre dikes cut the Abitibi River and lover formntions. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1934

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By H. Eyring, J. W. Fredrickson

Many theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying.certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.&apos; ZenerZ has reviewed and correlated the existing work on the anelasticity of metals. With these and others3&apos;4&apos;5 resent theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,l Smekal,8 Polanyilg Orowanlo and Taylor.&apos;&apos; Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic" process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome &apos;&apos;one at a time," in a manner of speaking, due to some stress-concentrating effect.13 Proposed Theory Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces.

Jan 1, 1949

By H. H. Stoek

Danville, the county seat of Montour county, Pa., was one of the earliest and best-known centers of the iron intlustry in the State. It is situated on the north bank of the north branch of the Sosquehanna river, twelve miles east of the confluence of the north and west branches of that river at Northurnberlttnd. The ore-belt, extending for a distance of twelve miles along the north bank, has been developed in a number of places, but nowhere so extensively as in the immediate vicinity of Danville. Hence, a description of the mines in that locality will suffice, as typical of the workings of the entire section. Geology. The Montour ridge consists of an anticlinal fold extending from the source of Wapwollopen creek on the east to the west branch of the Susquehanna, which it reaches at the mouth of Chilisquaque creek. According to the reports of the First Geological Survey of Pennsylvania, the length of the ridge is nearly twenty-seven miles, with an average breadth of three-fourths of a mile, and a maximum elevation of six hundred feet in the vicinity of Danville, where it also attains its greatest width. Just north of Danville the Mahoning creek cuts through it, exposing the iron-ore on the hill-side, where advantage has been taken of this to work the beds on the southern slope of the ridge by means of drifts. The sections given in Fig. 1 are taken from the reports of the First Geological Survey of Pennsylvania, made in 1858, by H. D Rogers, whose description of the Moatour ridge was so complete and accurate that the entire report was reprinted as an appendix to Vol. G 7 of the Second Geological Survey. The approximate crosssection shows that near Danville the top of the ridge is of Clinton vol, xx.—24

Jan 1, 1892

By B. W. Howlett, M. B. Bever, Somnath Misra

The heats of Formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 and the heats of solution of tellurium and selenium in liquid bismuth have been measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides have been measured in a constant temperature gradient calorimeter. The thermo-dynamic quantities are interpreted in relation to the stability of the compounds and the nature of the solid-liquid transition. THE selenides and tellurides of several elements of Group VB of the periodic system are of interest because of their electronic properties. The compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 are semi- conductors; they also have gained prominence in the fields of thermoelectricity and photoconductivity. However, little is known about their thermody-namic properties. As part of a research program on the thermo-dynamic properties of intermetallic compounds, the heats of formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 were measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides were measured in a constant temperature gradient calorimeter. The results, in addition to their intrinsic interest as thermodynamic quantities, contribute to an understanding of the stability of the compounds and the nature of the solid-liquid transition. 1) EXPERIMENTAL 1.1) Materials. Samples of the compounds SbzSe3 and Bi2Se3 were prepared by melting the elements in stoichiometric proportions in evacuated Vycor capsules followed by quenchinn in water. They- were then annealed in vacuum for 12 hr at 550°C. A sample of Sb2Te3, consisting mainly of one large grain, supplied by the Lincoln Laboratory,

Jan 1, 1964