Search Documents

By Oliver C. Ralston, Foster Fraas

Electrostatic methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to bene-ficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollas-tonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. The Separator The separator used in these tests is of the nonhomogeneous field type shown in Fig Ia. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll."

Jan 1, 1949

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By G. R. Fitterer

By means of the C-Sic thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. Commercial Development of This Device Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, procedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; nevertheless, it is felt that satisfactory gains have been made, inasmuch as each installation has indicated some effect of temperature upon the metallurgical operation, and has pointed the way toward technical and financial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-Sic thermocouple and the temperatures measured are discussed later in this paper. Temperature Variations or Liquid Pig Iron One well-known discussion between the blast-furnace and open-hearth (or Bessemer) departments has occurred intermittently for more

Jan 1, 1936

By G. R. Fitterer

By means of the C-Sic thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. Commercial Development of This Device Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, procedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; nevertheless, it is felt that satisfactory gains have been made, inasmuch as each installation has indicated some effect of temperature upon the metallurgical operation, and has pointed the way toward technical and financial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-Sic thermocouple and the temperatures measured are discussed later in this paper. Temperature Variations or Liquid Pig Iron One well-known discussion between the blast-furnace and open-hearth (or Bessemer) departments has occurred intermittently for more

Jan 1, 1936

By Joel H. Watkins

The terms kaolin, china clay, ball clay, and paper clay are more or less loosely and interchangeably applied to a large class of white-burning clays. These clays are made up chiefly of hydrous amorphous (colloidal) aluminum silicates with variable amounts of free silica and other impurities in small quantities. Occasionally also the term kaolinite is wrongly applied to a white-burning clay, for kaolinite is a mineral of definite chemical composition and definite crystalline form which occurs but sparingly in nature. It is not the purpose of this paper, however, to define or classify clays, or to enter into a discussion of the chemistry of clays. It is rather a general description of the occurrence and methods of mining of a kindred group of clays, and a discussion of their future economic aspect. In the Southern Appalachian States, the mining of white-burning clays has in recent years become an important industry. Although these clays are of several distinct types, which occur in as many localities under different geologic conditions, they are for the most part primarily of the same origin. They are essentially the same in elementary constituents, and are largely consumed in the game industrial arts. From the standpoint of a mining engineer, therefore, and for convenience in comparison and correlation, it should be interesting to discuss them under one heading. Kinds of Clay The most important types of clay which are now being actively mined in the Southern Appalachian States and with which this paper is particularly concerned are the North Carolina, Virginia, and Georgia kaolins or china clays (residual); the South Carolina and Georgia kaolins or paper clays (sedimentary); and the Florida and Tennessee plastic kaolins or ball clays (sedimentary). Other varieties which are interesting but which are as yet of little importance are the pocket deposits of white clay in Augusta County, Virginia, the bauxitic kaolins of Tennessee,

Jan 1, 1915

By C. F. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by some typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects. [ ] In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

Jan 1, 1928

By P. A. Beck, S. Kohara, M. N. Parthasarathi

IT has been shown1,3 that many observed phenomena related to annealing textures in f.c.c. metals can be adequately accounted for, at least in a qualitative way, by considering the orientation dependence of the boundary mobility, without any hypotheses concerning preferred orientation of nuclei. It was noted1 that this approach is particularly successful in the common cases of primary recrystallization in highly cold-worked polycrys-talline metals, where nuclei occur in great abundance, and that in the other extreme case, where the number of nuclei is very limited, or even only a single crystal is grown, the orientation dependence of boundary mobility has only a small effect, or none at all, on the orientations resulting from annealing. Recently Dunn described examples3-6 where observed secondary recrystallization textures apparently cannot be accounted for on the basis of oriented growth alone, but also require oriented nuclei, or at least the absence of nuclei in certain orientation ranges. In general, the great difficulty in correlating the preferred orientation of recrystallized grains with that of nuclei is inherent in the fact that nuclei are by nature very small, and that they are usually identifiable as "nuclei" only after growth, i.e., after they have already been subject to growth selectivity. An investigation was carried out by Liebmann and Lücke,' and also a very similar one by Graham and Cahn,' to obtain quantitative information on the orientation depend- ence of boundary migration rates in the recrystallization of slightly deformed aluminum single-crystal rods or plates, in which artificially nucleated recrystallized grains of predetermined orientation were grown. Liebmann and Lücke foupd maximum boundary mobility for boundaries across which the misorientation corresponded to a rotation of 40 deg around a common [Ill] axis, in accordance with earlier conclusions.9,1 Also, they confirmed that such an orientation relationship predominates among crystals growing into slightly extended single crystals from presumably random artificial nuclei. On the other hand, Graham and Cahn found no preferred orientation among crystals grown in a similar manner. It is not as yet known how these observations may be reconciled with each other. The view has been expressed in various papers5'10,21 that selective growth based on the orientation dependence of boundary mobility is not in itself sufficient to account for the formation of sharp re-crystallization textures, such as those often observed in highly deformed polycrystalline metals after annealing. The present work was undertaken to ascertain whether or not it is possible to obtain a sharp re-crystallization texture in a case where random nuclei are assuredly present in large numbers. It was previously found1' that high-purity aluminum crystals rolled 80 pct on the (110) plane in the [1T2] direction, when suitable precautions are taken, may be annealed for periods of about 1000 sec at 350°C without recrystallization. It was also found that the reluctance to recrystallize in this case is due to the scarcity of material in sufficiently deviating orientations to serve as nuclei. By using such a matrix,

Jan 1, 1959

By R. M. Lumley, J. D. Wood

In this investigation, polyethylene terephthalate (Mylar) was coated with various thicknesses of a vapor-deposited silvel- precoat followed by a uapor-deposited zinc using several orders of- magnitude variation in deposition rate of both the silver and zinc. The grain size and resistivity of the zinc film was primarily a function of the silver precoat thickness (in the range of 0.001 to 10 average Agprecoat thickness) and a secondary function of the zinc film thick-ness. The silver and zinc deposition rates were found to have a minor effect on the characteristics of- the zinc film. Electron and X-ray dilffraction results slwwed that all zinc films exhibited a fiber texture mith the (0001) axes essentially perpendiculav to the platze of the film When coating nonmetallic substrates such as paper or plastics with zinc metal vapors, it is found that the zinc will not condense unless extremely high evaporation rates or very low substrate temperatures are used. In 1931, Fraser' reported a procedure whereby zinc could be made to condense on nonmetallic substrates by depositing a very thin precoat of silver. Utilizing Fraser's method, the ermans' developed a commercial process of making "metallized film" capacitors during World War 11. The metallizing process, which was introduced in the United States shortly after the conclusion of World War 11, became one of the first large-scale commercial applications of vapor-deposited metal films and remains one of the larger applications in the electronics industry. The process, as developed by the Germans, consisted of depositing a thin precoat of silver on lacquered, kraft paper followed by a conducting layer of zinc. The resulting silver-zinc film was used as the capacitor The term silver-zinc will be used throughout thiz paper to mean a metal film formed by an extremely thi layer of silver, 10A or less in average thickness, and a zinc film IOOA or more in thickness deposited on the silver film. ---. electrode with the lacquered paper being the dielectric. When polyethylene terephthalate was marketed by E. I. Du Pont Co. in the early 1950's under the trade name Mylar it was substituted for the kraft paper in many capacitor applications. Even though manufacture of metallized paper and metallized Mylar capacitors has been a large commercial process for many years, little information has been published about the deposition parameters. Correlating the work of others to the various effects to be expected of deposition parameters on silver-zinc films deposited on Mylar, it is expected that the

Jan 1, 1967

By B. Barlin

Introduction The development of metallurgical practice at lambia Broken Hill is directly related to the change in mineralization of the deposits as mining progressed from the open pits to underground. The ore consists of a mixture of lead and zinc sulphide minerals, together with abundant silicates, carbonates and other oxidized minerals of these metals. The irregularity that characterizes the shape of the orebodies applies equally to their mineral content, which makes ore reserve calculations and the maintenance of a balanced feed to the metallurgical plants, problems of some magnitude. History The Rhodesia Broken Hill Development ,Company was formed in 1904 after an Australian prospector, T. G. Davey, discovered the outcrops in 1902. In the early years zinc ores were calcined for shipment but this proved uneconomic. Cerussite outcrops were then smelted directly in blast furnaces for the production of lead until 1929 when ore above the water level was exhausted.

Jan 1, 1970

By G. P. Conard, E. H. Rennhack

The generation of fibers composed of individual TiZn15 compound particles and their influence on crystallographic orientation in chill-cast, hot-rolled hypoentectic Zn-Ti alloys were explored. Metallo-graphic examination and X-ray diffraction data show that such fibers form a planar network after 50 pet reduction which eventually tends to suppress twinning at some critical reduction level (-90 pct) where the grain size approaches the interfiber, spacing. This leads to the development of a duplex-type projerred orientation through slip rotation consisting of an al-most ideal (0001)(2iiOj texture and a (0001) (1010) rotated component. Correlations between basal-plane rotation and secondary- creep rc11e sugg-est, however that prejerred orientation does not contribute in a major way to the creep resistance of these alloys. EFFORTS to improve the creep resistance of zinc through alloying without incurring a loss in fabricating properties have achieved only minor success with the exception of the very effective addition of titanium. Anderson, Boyle, and Ramsey,l for example, demonstrated that increasing the amount of thiselement from 0.05 to 0.23 wt pct produced a progressive, 45-fold increase in the inverse creep rate of hot-rolled

Jan 1, 1967

By Charles S. Barrett, Robert F. Mehl

The system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that developed by Bijl l (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1930

In 1776 two Franciscan friars, Dominguez and Escalante, started to find a direct route from Santa Fé to Monterey, and in their misguided wanderings northward they reached Timpanogos, now known as Utah lake, where they heard of a much larger body of water to the northwest, of which they were told that it was extremely salt.* They never saw this great lake, because they passed south of it on their way to the Pacific coast. The Dead Sea of North America was discovered in 1835 by James Bridger, a trapper. He and other trappers had ascended the Missouri and had reached the Bear river. A discussion arose as to the course of this river, and a bet was made, to settle which Bridger followed the Bear river to its source, in the Uintah mountains, and from the crest of the watershed he caught sight of the lake, to which he then descended.† He tasted the briny water of the inland sea and wondered if it were an arm of the Pacific Ocean. The lake was first seen by the Mormons on July 24, 1847. A band of them, numbering 145 and led by Brigham Young, had migrated from Missouri in search of a new home in the western wilderness. It is recorded that when Brigham Young stood on the summit of the pass over the Wasatch range and saw the valley of the Jordan outspread before him, he exclaimed: "It is enough. This is the right place". He had seen it in a vision, so he claimed, and foresaw the future glory of the new Zion that was to be planted in that happy

Jan 1, 1932

By Alexander Field

INTRODUCTION THE Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity, apparatus, furnace and other accessories mentioned in this paper have been described fully in a Bureau of Mines report.1 THE LITERATURE ON SLAG VISCOSITY The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method or, other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations.-of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity, the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see, the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300° C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 2, 1917

By Rossiter W. Raymond

The extent to which the divining-rod is still used in this country for the detection of hidden treasure, mineral veins, or springs, is ' much greater than educated persons would be likely to suppose. For many years wells have frequently been located by its aid in New England, where the belief is widely extended among the farmers that in the hands of peculiarly gifted persons this instrument possesses special virtue. Large numbers of the oil wells of Pennsylvania

Jan 1, 1883

By Walter S. McKee

When mixed with common cast steel in quantities ranging from 11 to 131/2 per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time.. * At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 Ib. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13.5 per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 51/2 in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 51/2 in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an important consideration if the casting is to be a moving part in a machine. At the same time, the thickness of 51/2 in. is sufficient to permit the use of manganese steel for the heaviest classes of machinery.

Jan 1, 1916

By F. J. Hurst

The rapid expansion of the phosphate fertilizer industry in conjunction with the projected shortage and spiraling price increase of uranium has greatly renewed interest in wet- process phosphoric acid as a significant source of uranium. Two attractive solvent extraction processes for recovering uranium from the acid have recently been developed and tested through bench-scale at Oak Ridge National Laboratory. One of the processes has been successfully tested on a pilot-plant scale at phosphate plants; the second process, which offers several potential advantages, still needs additional testing. The merits of each process are discussed.

Jan 1, 1978

By T. E. Seidel, A. U. MacRae

The dependence of the electrical and crystalline properties of silicon containing ion implanted boron atoms have been studied as a function of the incident dose, substrate temperature, and annealing tempera-ture. Hall effect studies show that the compensation due to defects is negligible after annealing at and above 500°C for a dose of 1013 ions per sq cm. Steps occur in the isochronal annealing curve for the sheet resistance at 300°C and 800°C and the mechanisms responsible for these steps are discussed. The range of the ions at 150 kev is 3500 * 5001. Electron diffraction studies on samples implanted with 150 ker ions show the existence of damaged (polycrystalline) silicon closer to the surface than the range of the ions. Etching and subsequent annealing of etched and unetched specimens suggest that the poly crystalline silicon is closer to the surface than the bulk of the distribution of ions. THE purpose of this study is to investigate some electrical and crystalline properties of ion implanted boron in silicon. Sheet resistance, Hall measurement, depth distribution by chemical staining, thermal probe and electron diffraction have been used to study the properties of samples implanted in a random direction with ions having energy up to 150 kev. The boron-silicon system has been the subject of considerable study'-7 due to its possible application in the fabrication of electronic devices. The implanted ions produce considerable crystalline damage to the substrate crystal before they lose most of their primary energy and come to rest. Fortunately, most, if not all, of this damage can be removed by subsequent annealing or by holding the substrate at an elevated temperature during the implantation process. Sheet resistivity measurements of the p-type layers produced by boron implantation into room-temperature silicon, reveal that the annealing occurs in a two-step process: the first occurring at -300°C and the second at -800°C.' Electron-microscope and low-angle electron diffraction studies of this damaged material indicate that the bombarding ions produce an amorphous silicon region about the trajectory of each ion.' At high doses, these damaged regions overlap and an amorphous surface layer results. Furthermore, the 800°C annealing step, appears to be associated with the elimination of this gross damage. The depth distribution of the as-implanted and also the annealed samples have been studied by an angle lap and staining technique as well as by Hall measurements.3-7 We find the experimentally determined ranges of the boron are less than those calculated by the Lindhard-Scharff-Schiott theorys (hereafter referred to as the LSS theory). Our results are in essential agreement with pre- vious results. In addition, we have made Hall measurements on samples bombarded with a low dose (2 x 1013 ions per sq cm) to minimize impurity banding effects, and find that deep ionized levels influence the carrier concentration and room-temperature hole mobility until the sample is annealed at temperatures above 500°C. Above this temperature, the data corresponds to that obtained when silicon is doped with boron by conventional techniques. We have also made a depth distribution determination of the crystalline damage due to the implanted boron by using glancing angle electron diffraction techniques. It was found that the gross damage depth distribution of heavily implanted samples is closer to the surface than the depth distribution of the electrically active boron. By removing this gross damage, without affecting the distribution of the implanted boron, we have determined that the 800°C annealing stage is not exclusively due to the improvement in the crystalline perfection of the amorphous material but also appears to be associated with the annealing of some point defects. These results and their relation to previous results are discussed in the following sections. IMPLANTATIONS Boron ions were implanted into silicon samples using an accelerator capable of operating from 10 to 150

Jan 1, 1970

By Henry U. Ross

The behaviour during reduction of iron-ore pellets and sinters was investigated. Several methods for the preparation of agglomerates and their reduction were tried. Commercial agglomerates from world-wide sources as well as experimental samples were tested. The effect of coke additions to pellet and sinter plant feeds was given special consideration. An analysis of the test results has helped to explain many of the phenomena associated with the reduction of iron-ore agglomerates such as swelling, loss in strength and wear resistance, changes in porosity, changes in mineralogy and the formation of metallic iron and slag. A double-layer pellet with all of the coke concentrated in the core proved particularly interesting. Although large quantities of coke showed that partially reduced agglomerates containing metallic iron could be produced in the laboratory, the problem of producing reduced pellets and sinters by the existing agglomerating processes still remains.

Jan 1, 1977

By Samuel B. Christy

Jan 1, 1889

By E. T. Stephenson

Wert and Marx1 pointed out that a straight-line relationship exists between the activation energy of a relaxation process and the temperature at which the maximum relaxation occurs. The data available at the time indicated that this relationship held for a number of Snoek peaks, several grain boundary peaks, and pair relaxation in a brass. Theoretical justification for the observed relationship was found in the following equation, which Wert and Marx derived from the theory of interstitial atomic diffusion coefficients:' where AH is activation energy, R is the gas constant, T is the internal friction peak temperature, v is the interstitial atomic frequency, f is the frequency of the applied stress, S is entropy of activation. More accurate internal-friction data on interstitial diffusion in bcc metals have become available since Wert and Marx's paper. Table I gives activation energies calculated by several authors from a combination of elastic aftereffect data and the peak temperatures at several frequencies of measurement. (In the case of Fe-C and Fe-N, the referenced authors5'7'8'10 also used high-temperature diffusion data.) However, diffusion experiments at 150°C and above1'-13—rather than anelastic techniques—were used to determine the activation energy of hydrogen diffusion in Fe-H. In order to plot this recent data as a AH vs T graph we calculated the peak temperatures of the systems listed in Table I (with the exception of Fe-C, Fe-N, and Fe-H) by using published values3'' of AH and Do. These calculated peak temperatures varied by only a few degrees from experimentally determined peak temperatures. The calculated values were felt to represent the better average. A number of investigators have found the peak temperatures in Fe-C and Fe-N to be 38 to 40°C and 20° to 24°C, respectively. The values of 39" and 22°C (312° and 295°K in Table I) were determined by carefully executed experiments.6'8 The hydrogen peak temperature has been measured at 1 cps,12 20 cps,14 and 35,000 cps.15 All hydrogen peak temperatures were adjusted to 1 cps for Table I using AH = 3000 cal per mole. As Fig. 1 shows, the data of Table I fit a straight line at least as well as the earlier data used by Wert and Marx. Linear-regression analysis was applied to the data in Table I. The Fe-H data was omitted because the activation energy has not been experimentally determined in the temperature range of the peak. The analysis yields the equation: with a standard error of 860 cal per mole. The agreement of the data in Table I with the Wert-Marx equation is excellent. Strict application of Eq. [I] forces the linear regression analysis through the origin. In this case, the analysis gives a slope of 62.1 cal per mole per deg, and a standard error of *890 cal per mole. With this value, it follows from internal-friction theory that Hence, Do varies by only 30 pct among these bcc-interstitial systems. Thus, a concept suggested originally by Wert and Marx1 is confirmed by recently published data. The

Jan 1, 1965