Search Documents

By E. T. Laker, John C. Loretto

This chapter deals with the process piping aspects of moving slurries in mineral processing plants and the transportation of slurries such as tailings and concentrates over longer distances. The basic data required to select the process piping is given together with an example of line sizing and material selection. Alternative piping materials are discussed together with pumps and pumpbox design and the types of valves and other fittings available to the process piping designer. The long distance transportation of slurries is briefly discussed and a number of references given on this, including papers on actual installations.

Jan 1, 1978

Open pits and quarries are the major sources of all hard rock tonnages mined today. Normally, ore is fractured from the pit bench face by blasting and then truck-hauled to a primary crusher on the pit rim for conveying to the concentrator; overburden (or waste) is generally truck- hauled from the pit to dump areas. This system of truck haulage of blasted ore and waste accounts for some 25 to 50% of total mining costs in a typical open pit operation and commonly is the largest single cost factor. In an effort to reduce these costs mining companies are continually replacing their older and smaller trucks with larger ones and at the same time are studying conversions to conveyor haulage, since this method of transport seems to offer possibilities of lower costs per ton of material handled. In these studies it seems logical to consider installing these conveyors as close as possible to the mining face for maximum use of conveyors and minimum use of trucks, since a conveyor is much less labor intensive than a trucking system. However, direct loading onto a conveyor near the retreating bench face is impractical because of excessive lump size. Consequently, it is conventional practice to load the blasted rock into trucks at the face for haulage to the crusher. After crushing, the rock is fed onto a conveyor. The closer the crusher is to the mine, or if it is in the mine, the shorter the truck haul and the greater the potential for cost saving. At first appearance, in-pit conveying might seem to be an obvious solution, yet many mining companies have considered such a move while few have implemented it. To determine why, it is necessary to consider the factors influencing such a decision. A conveyor system tends to be capital intensive but can have a lower operating cost per ton than trucks. Trucks, on the other hand, tend to cost less to buy but more to operate; thus, economics tend to favor the conveyor if it can be operated close to capacity and if a sufficiently large tonnage can be passed over the system to mitigate the effect of its high capital cost. In a typical hard-rock, open-pit mine it is necessary for a variety of reasons to mine several faces of both ore and waste at the same time; and any mining system must have sufficient flexibility to permit loading from one face or another at short notice. This makes it impractical to place small mobile crushers and their consequent network of conveyors at each working face. To date no alternative has been found to using trucks for bringing all rock of the same class to some convenient marshalling point from which it may be crushed and conveyed from the pit. Another advantage of trucking when compared to conveying is flexibility. Many mines wish to deliver their shot-rock to different locations, depending on the mineral content. For instance, a typical copper mine may have to simultaneously mine milling ore, leach ore,

Jan 1, 1978

By V. E. Christensen

AT most smelting plants, forced draft, induced by high stacks or fans, is used to carry the gases away from the furnaces, roasters, or sintering plants. Gases moving under forced draft carry varying amounts of solids in the form of dust and fume. Where the weight of the solids is material, and the metal content high, it is usually profitable to treat the gases to recover these solids. Baghouses, Cottrell treaters, and settling chambers are the common forms of plants used to recover solids from gases. To check on the efficiency of these plants it is necessary to know the volume of gas leaving the plant and the amount of solids carried by the gas. As the volume of gas is equal to the product of the velocity of that gas and the cross-sectional area of the flue, the determination of the volume includes the measurement of the area of the cross section and the determination of the velocity. The velocity is generally measured by means of the Pitot tube and Ellison differential pressure gage, although low velocities are best determined by means of an anemometer. The dust concentration is determined by passing a measured volume of sample through a filter and weighing the dust caught. From this the dust concentration per unit of volume may be calculated. It is necessary to assume that the gas is homogeneous or that each cubic foot of the gas contains the same weight of dust as every other cubic foot. Having the volume of gas passing through a flue per unit of time, and the dust concentration of the gas per unit of volume, the amount of solids may easily be calculated.

Jan 1, 1935

By David White

THE submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safe-guard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immediate review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the ground. With the members of this cooperative committee, state geologists, regional geologists, consulting specialists, and geologists and engineers attached to many companies worked both independently and through sub-committees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnson, Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman.

Jan 6, 1922

By W. J. Putnam, H. F. Moore

THIS paper gives a preliminary summary of results of tests on the resistance to fatigue under reversed stresses of steel subjected to cold-working and of tests to determine the effect of rest on the endurance of steel under reversed stresses. The tests of cold-worked steel were undertaken as part of an investigation by the National Research Council Committee on Fatigue Phenomena of Metals and were made by Mr. Moore; the tests to determine the effect of rest are part of an investigation now being made by Mr. Putnam. Both series of tests were made in the Materials Testing Laboratory of the University of Illinois. The preliminary results of these tests are reported now because it is believed that test data on fatigue strength should be available at the earliest possible moment; however, it should be clearly kept in mind that this paper gives preliminary results and is intended to encourage discussion rather than to give final conclusions. Before giving the data of the tests, the writers will explain the term "fatigue strength" as used in this paper and will discuss briefly the method used in interpreting the test data of repeated-stress tests. " The term fatigue strength, as applied to a material, may be defined as that maximum fiber stress that will cause fracture of the material after the repetition of any given number of cycles of stress, each cycle involving the variation of stress from a minimum to the above maximum. The fatigue strength, then, varies with the number, of repetitions occurr,ing in the lifetime of a structural or machine member and with the range of stress for each cycle of stress. The fatigue strength will be lower for a member in which the stress is completely reversed than for one in which the stress varies from zero to a maximum. In interpreting test data from fatigue tests under reversed stress, the stresses and corresponding numbers of repetitions required for failure are plotted on logarithmic cross-section paper. In 1910, Professor

Jan 1, 1920

By C. R. Johnson, R. A. Greenkorn, R. E. Haring

Three confined five-spot miscible displacements at unity, favorable, and unfavorable mobility ratios were conducted in a shallow, water-saturated sandstone of Pennsylvan-ian age near Chandler, Okla. These studies, plus associated laboratory experiments, were designed to measure miscible displacement performance in a controlled natural system, using known scaling criteria to develop an approach to modeling the heterogeneous field system. We have concluded from these studies that: (I) displacement efficiency in the field is a pronounced function of mobility ratio, indicating that miscible fingering observed in simple laboratory models occurs in the field: (2) field displacements can be quantitatively predicted by scaled laboratory models if the degree and location of field permeability variations are preserved in the models: and (3) arbitrary simplifications of heterogeneity will not necessarily predict observed displacement efficiency, and the simpler the model, the more optimistic the prediction. INTRODUCTION Many processes to achieve miscible displacement of reservoir oil by injected fluids have been conceived and field tested by the oil industry. Among the better known are high-pressure gas, enriched gas, and LPG banks. The simplest form of miscible displacement—one fluid miscibly displacing another fluid of different viscosity but the same density—has been studied extensively in homogeneous laboratory models. Observations of unstable fingering have been made which explain the significant decrease in displacement efficiency as the mobility ratio (ratio of displacing fluid mobility to displaced fluid mobility) increases. General industry experience with field tests of miscible displacement projects, mostly LPG banks, has been premature solvent breakthrough and lower than predicted production rate increases. These results have been attributed to either unstable fingering, unusual or unexpected permeability stratification, or both. Miscible displacement data in a controlled natural system have never been reported, however. Also, it has not been shown that properly designed and constructed laboratory models quantitatively predict field-scale behavior. The purpose of the combined field and laboratory ex- periments reported in this paper is twofold. The first was to measure miscible displacement performance at different mobility ratios in natural rock approaching field size under precise, controlled conditions. The second purpose was to utilize known scaling criteria plus several approaches to heterogeneity to model the field. Comparison of model and actual field results should then determine whether or not the laboratory phenomena (manifested by miscible displacement efficiency) are exhibited in large, natural rock systems. We carried out our program by first locating a shallow, water-saturated reservoir whose rock properties were representative of oil-bearing reservoirs. Detailed reservoir description by core analysis and interference testing showed the field site to be heterogeneous. A sequence of controlled, aqueous-phase miscible displacements was conducted at unity, favorable and unfavorable mobility ratios. A central, confined pattern was used to obtain the displacement data. A laboratory program using sand-packed models was conducted to determine the modeling criteria necessary to simulate field behavior of miscible displacement in a heterogeneous system. SCALING THEORY The detailed derivations and descriptions of the scaling laws that apply to laboratory models of reservoirs are adequately described elsewhere, so the following discussion will be restricted to facets of importance in this study. For a displacement in which one liquid miscibly displaces another, the following dimensionless groups are required to have the same numerical value in the model as in the field: The model also must be geometrically similar to the field, be spatially oriented the same as the field (same dip angle), and have the same initial and boundary conditions as the field (same initial fluid saturations and same injection-production well arrangement). When these conditions are satisfied, the theory predicts that at dny dimensionless time (pore volumes of produced fluids) the dimen-sionless flow potential and dimensionless fluid concentrations will be identical at all dimensionless spatial locations within the model and the field. If this prediction is correct, then the local dimensionless velocities must be identical, thus the instantaneous fraction of displaced fluid produced and the cumulative recovery expressed as fraction of original fluids in place must be identical at all dimensionless times. The theory outlined above has been obtained by either dimensional analysis or inspectional analysis of differential

Jan 1, 1966

By Donald C. Barton

Success in the use of the Eötvös torsion balance method of mapping geologic structure depends largely on the accuracy in the interpretation of the observed results. Skill in that interpretation depends (1) on the knowledge of the types of the variation of gravity, the gradient of gravity horizontally, and of the differential curvature produced by bodies of different sizes, shapes, dimensions, and densities; (2) on the knowledge of the possible types of structural bodies which might produce the observed anomalies; (3) on the empirical knowledge gained by experience not only in the geological interpretation of torsion balance surveys, hut of interpretations of inadequate geological data; and (4) on a knowledge of the possible and probable types of geologic structures in the area of the survey. The knowledge of the anomaly which a known body will produce and conversely the knowledge of the body or bodies which will produce a known anomaly may be gained by empirical experience and by mathematical study. The knowledge gained by empirical experience is fragmentary and inexact. The geology of most structures actually is known very superficially. The surface geology may be known accurately. If the structure is petroliferous, the subsurface geology of the oil field will be known down to 3000, 4000, 5000 ft. or in a few oil fields down to 7500 ft., but the deeper geology will be unknown and the metamorphic, igneous, or massive limestone basement below the reach of the drill may contrast sharply in density with the overlying sediments. Away from the oil field, the subsurface geology is known only from scattered drill holes, which do not go to the basement. A fair but not necessarily accurate knowledge of the geology of the nonproductive area can be obtained by correlation of the wells but the degree of its accuracy in general is proportional to the density of the occurrence of the wells. The geology below the bottom of the wells however is unknown. An anomaly mapped by the torsion balance is the sum of the effects of the contrasts in mass of its whole geologic surroundings. If the dimensions of a body of abnormal density are large enough, depth or distance makes no difference in the effects on the gradient and differential curvature; and as a matter of fact, in many places, the basement and irregulari-

Jan 1, 1929

ARTHUR PHILLIPS,* Bridgeport, Conn. (written discussion?).-It is to, be regretted that the very valuable paper by Messrs. Bassett and Davis did not appear in the early war period. The data presented would have been of inestimable service to inspectors, of cartridge brass who, admittedly, had little or no knowledge regarding the relation of grain size to temperature of anneal, and no real appreciation of, the significance of the Brinell hardness test. The paper is of considerable interest to, metallurgists also. WALTER R. HIBBARD, ? Bridgeport. Conn. (written discussion§).-The writer has carefully studied Messrs. Bassett and Davis's paper with considerable interest, inasmuch as our laboratory has tested cartridge brass by means of a Brinell machine. In March, 1917, at the suggestion of the Technical Department of the American Brass Co., we started a comparison of grain-size measurements and Brinell hardness of-cartridge brass with a gage of 0.1 in. or greater. This was continued until March, 1918, when we adopted the Brinell hardness test as standard for brass 0.1 in. gage or greater, and discontinued grain-size measurements upon this metal. The data collected during the test showed that the Brinell hardness indicated more accurately how the metal acted in actual working operations. It was also more reliable because two manipulators check themselves closer by the Brinell test than by the grain-size measurements. It also consumed less time in making the tests. Alfred V. de Forest, formerly assistant research engineer of our laboratories, has described the apparatus and some of the checking results in a paper read June, 1918, before the American Society for Testing Materials.1 The writer hopes that a more satisfactory. method for testing cartridge brass and gilding in gages thinner than 0.1 in. may be devised than the present method of grain-size measurements.

Jan 3, 1919

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll' in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod'. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By C. L. Mantell

Although so common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium, titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well below the melting point, say at 110° C. for a half hour or for a few minutes at 150" C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin meta1 in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intererystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moire metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, .which result from the method

Jan 1, 1929

By C. L. Mantell

Although so common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium, titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well below the melting point, say at 110° C. for a half hour or for a few minutes at 150" C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin meta1 in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intererystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moire metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, .which result from the method

Jan 1, 1929

By N. B. Davis

I . INTRODUCTION WHILE working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity, This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 2, 1915

By Edward O’Toole

THe Pocahontas district occupies the extreme southern end of West Virginia, principally McDowell, Mercer and Wyoming counties, and a part of Tazewell county, in southwestern Virginia. The first record of the coal field is a report by Prof. J. P. Lesley, of Pennsylvania, about 1880, in which he mentions a coal opening at the upper end of Abbs Valley, Tazewell county, Va. C. R. Boyd, a mining engineer of Wytheville, Va., published a series of articles in 1881, mentioning coal on Indian Creek, Tazewell county, and on Horse Pen creek, which coals, he stated, extended toward the Ohio River. He also mentions the Abbs Valley coal reported by Lesley. In 1881, F. J. Kimball (who became president of the Norfolk & Western R. R. in 1883)) after examining the Scott mine in Abbs Valley, went northward across Abbs Valley Mountain to the place now known as Pocahontas, where he located what has since been called No. 3 vein of Pocahontas coal. In November, 1882, Jed Hotchkiss and others prepared a cross-section of the Flat Top Mountain coal measures, some notes on which were published by Mr. Hotchkiss, between 1880 and 1892, under the title of " The Virginias.' In May, 1881, the Norfolk & Western R. R. was organized through the purchase of the Atlantic, Mississippi & Ohio R. R., an old line running from Norfolk, Va., to Bristol, Tenn., with branches from Petersburg to City Point and from Glade Springs to Saltville. At that time, charters had been granted for three railroads tributary to the New River Valley, but their proposed routes would indicate that the promoters were concerned with minerals, timber, and a connection with the Chesapeake & Ohio R. R., rather than the development of any coal in the Pocahontas district. One of them was projected to extend up Bluestone River a short distance, but not far enough to reach the coal in the Bluestone Valley, and a little grading was done for a narrow-gage road between New River Station and a point in Giles county, Virginia, near the West Virginia line. All charters and railroads in this district were acquired by the Norfolk & Western R.R.

Jan 1, 1925

By Pradeep K. Rohatgi, Clyde M. Adams

Structures obtained on freezing of several hypo-and hypereutectic Al-Cu alloys over a range of solidification rates have been examined. Dendrite spacing, L, increases linearly with solute concentration and with the square root of the inverse freezing rate. The relationship for hypoeutectic alloys is: where rate of change of fraction solid with time, is freezing rate, C is solute concentration, (pct Cu)=1. Mass transport in inter dendritic liquid during solidification is analyzed; the experimental observations suggest maximum concentration differences and constitutional supercooling in the inter dendritic liquid increase with an increase in the solute concentration. The dendrite morphology changes with freezing rate and alloy composition. The dendrites of the a phase are parallel, uniformly spaced plates with slow freezing and rods with rapid freezing. Nonor-thogonal side branching has been observed in phases with cubic and tetragonal structures. Side branches in a dendrites are orthogonal with slow freezing and at 60 deg with rapid freezing. Formation of second-phase envelopes around the Primary phase is also discussed. DENDRITIC structure is characteristic of many types of phase transformation. The most extensively studied so far has been solidification of liquid solutions. chalmersl and coworkers have interpreted the formation of dendrites in terms of the breakdown of a planar interface. Most of the work done concerns itself with the development of an instability at the interface. Little theoretical work has been done quantitatively to relate the parameters of dendritic structure to mass transport in the liquid phase. A few empirical relations based on the experimental2'3 observations exist in the literature. Several workers2 including Brown and Adams1 have studied dendrite spacing in A1-Cu system as a function of solidification variables. In most cases, dendrite spacing has been found to increase linearly with the square root of some parameter proportional to the freezing time. The effect of solute concentration is not clear; some workers report the dendrite spacing increases with solute concentration4 whereas others report vice versa.''' ~ohatgi' has observed an increase in the spacing between ice dendrites with an increase in solute concentration in water. Tiller has also suggested that dendrite spacing should increase with solute concentration. In the present work dendrite spacing and morphology have been examined as a function of solute concentration and freezing rate. The freezing rate is defined as the fraction of liquid solidified per unit time, dfs/dß?, where f, is the fraction solid and 8 the time. The fastest freezing rate studied was 4550 times the slowest freezing rate. THEORETICAL CONSIDERATIONS It is of interest to analyze the concentration distribution in the liquid phase between growing dendrites during solidification, Fig. 1. Since this distribution is a direct consequence of the rejection of solute by the growing solid, a diffusional process, the concentration gradients increase with the freezing rate. However, when solidification rate is the only variable in a series of experiments, the interdendritic liquid regions become smaller (i.e., the dendrites become more closely spaced) with an increase in freezing rate. The main purpose of the analytical treatment of interdendritic liquid diffusion will be to reveal a tendency for dendrite spacing to decrease with increasing solidification rate in just such a way that the maximum concentration differences developed in the liquid phase are remarkably independent of freezing rate. Two rather different analyses are set forth, one pertaining to the one-dimensional diffusion which obtains in the interdendritic liquid between parallel plate-shaped dendrites, and the other to the cylindrically symmetrical diffusion around rod-shaped dendrites during early stages of solidification. The results of the two analyses are quantitatively similar, correlating dendrite spacing, maximum concentration difference, and freezing rate. First consider the simpler one-dimensional case. Two parallel plate-shaped dendrites are separated by a distance, L, between centers, Fig. 1. Solidification takes place by the thickening of these plates, with solute being rejected into the liquid. It is assumed there is no diffusion in the solid. This thickening process is slow enough and the dendrite spacing small enough that the concentration differences which develop, although interesting and important, are very small (an important assumption which is verified ex-

Jan 1, 1968

By C. A. Rowland, R. C. Nealey

Until recently there were very few dry grinding rod mills used. The early installations performed as anticipated. In the last seven years a number of dry grinding rod mills have been made, most of which have been used for grinding iron ore. The recent installations have not operated as anticipated in accordance with practices learned from wet rod milling. The paper does not establish any definite rules for the application of dry grinding rod mills but does attempt to establish some guidelines that can be followed. The paper reviews a number of flowsheets describing the problems encountered and some of the solutions found. Completely dried compared to partially dried feed is reviewed. Problems encountered in scaling up from pilot plant to production-size mills are described. Rod sizing, effect of rod length, rod bending, rod breakage, and rod tangling are discussed. While wet grinding rod mills have been used for 50 years to grind ores and make specifications sands, dry grinding rod mills have only recently come into significant use in the mineral industries. Among the materials now being processed in dry grinding rod mills are (1) lead sinter, lead slag, and limestone; (2) iron ore; (3) silica; (4) cement clinker; and (5) coke. Because the application of wet grinding rod mills was well understood at the time that dry grinding rod mills were introduced, the criteria and guidelines for selecting the former were carried over to the selection of the latter - in some cases with the anticipated results, but in many cases not. It is the purpose of this paper to describe, through a series of flowsheets, some of the recent problems encountered with dry grinding rod mills, to point out the solutions to these problems, and to set forth some guidelines for the selection and application of these mills. When dry grinding rod mills came into use, the following facts about their wet grinding counterparts were already well established: (1) The performance of large-sized mills can be accurately predicted from the performance of rod mills 5 or 6 ft in diameter. Wet grinding mills as large as 14 ft in diameter (inside shell) by 20 ft long with rods 19.5 ft long can operate satisfactorily.

Jan 1, 1970

By E. A. Anderson

In 1918 the American Society for Testing Materials held a symposium2 on what was then known as season cracking. The sessions included six papers, all on brass. During the ensuing 26 yr., many new workers have come into the field and several other metals have been found subject to failure by stress-corrosion cracking when the right combination of stress and environment is achieved. It is not surprising, therefore, that the present symposium has brought forth 29 papers covering alloys of seven important metals. The phenomenon of stress-corrosion cracking is not necessarily confined to these seven metals. Dix3 has stated, "Indeed, it is probable that ingenious investigators can find solutions which will stress-corrosion crack any known metal or alloy." Mears, Brown, and Dix4 have indicated that stress- corrosion cracking failures are not necessarily limited to metals but may include the plastics. It is to be expected that the increase in the number of metals known to crack in service and the general emphasis on such failures at a symposium such as this will alarm many to whom the subject is un- familiar. Such alarm is not justified by the record. It is true that stress-corrosion

Jan 1, 1945

By A. G. McGregor

DURING the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and. equipment developed. Some of these features are described in this paper. CONCENTRATE HAULING, UNLOADING AND SAMPLING SYSTEM (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co.. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences.

Jan 8, 1916

By Lucien F. Trueb

The microstructure of explosion-bonded pairs of similar and dissimilar metals has been investigated by electron microscopy. A review of the specific problems encountered and the methods used for obtaining surface replicas and thin-film transmission specimens of the bond interface is given. The bond area is mainly characterized by continuous and practically diffusionless metallurgical bonding. The very large shear stresses induced along the collision front of the plates being joined causes extreme grain elongation and a symmetrical pattern of subgrains in the bonding direction. The bond zone is also characterized by a very high density of dislocations and pressure-induced twins. Localized heating occurring during the cladding process can result in partial re-crystallization or the formation of thin layers of molten material. The force of precisely controlled explosions causing a high-velocity impact between metal plates has been used for several years to achieve metallurgical bonding between an extremely wide variety of metals. This method essentially consists of accelerating a plate to high velocity toward a stationary plate by a detonating explosive. Since the restrictions to bonding are not those encountered with conventional nethods, it becomes possible to bond pairs of metals having widely different mechanical properties that are immiscible or form brittle intermetallic compounds. Many applications of such composite metals are found in the field of corrosion protection as well as numerous other fields; for example, explosion bonding is being applied for fabricating the materials used by the United States Mint in the new sandwich-type coins. The primary condition for establishing a metallurgical bond is that absolutely clean metal surfaces be brought together. Any metal exposed to the atmosphere is covered with oxides, adsorbed gases, and other contaminants; even a very forceful impact of two such surfaces is not sufficient for bonding. Cowan and Holtz-man,"' who reviewed the dynamics of colliding plates in detail, showed that in order to achieve a good bond the explosion conditions must be chosen in such a way that the plate collision velocity is less than the sonic velocity, in which case no oblique shock waves are attached to the collision front. A pressure wave is then generated ahead of the collision line, and the material forming the colliding surface of each of the plates flows forward and is ejected in the form of a spray, the so-called jet. The dynamic elastic limit of the metals must be exceeded so that there is sufficient plastic deformation. At the point where the jet formed by the junction of the inner surface layers of both plates separates from the combined plates, the material experi- ences a very high shearing strain and the pressure can reach several hundred kilobars. This process strongly influences the microstructure of the bond zone as will be seen later. Behind the collision front, uncontami-nated layers of internal material are brought together under high pressure and are thus metallurgically bonded. I) STRUCTURE OF EXPLOSION BONDS The different types of explosion bonds that can be obtained depend on the explosion conditions, and have been investigated by Cowan and Holtzman,1'2 Holtzman,3 Klein; Bahrani and crossland,' and Buck and Horn-bogen. The preferred kind for practical applications is the so-called wavy bond, typical examples of which are given in Fig. 1 showing light micrographs of various metal-to-metal interfaces. In forming this type-- of bond the collision energy is mainly expended in jetting, the formation of waves, and localized melting. Beyond the crest of the waves, eddy-shaped areas are observed in which the two metals are mixed in a complex pattern of streaks. Cowan and Holtzmanl first proposed that this wavy pattern is analogous to periodic eddy shedding in the flow of a viscous fluid around an obstacle (Von Karman's eddy street). The mass of metal ahead of the stagnation point, which is associated with the jet and has forward momentum, plays the role of an obstacle and the eddies created in the flow of solid metal around the stagnation point are preserved in the final clad specimen. This idea has been reviewed more recently by Klein4 and the variables involved in the wave formation have been discussed in some detail by Bahrani and crosslands and Buck and Hornbogen.6 Several studies of the structure of explosion bonds by light metallography have already been published.1-6 Aside from the waviness and the eddies which were mentioned above, the most striking characteristic of the area in the vicinity of the bond interface is a very considerable longitudinal grain deformation which appears to be strongest at the metal-to-metal boundary and dies out as one moves away from it. Large twins are often observed within the deformed grains, and molten areas are found in the center of the eddy-shaped structures situated beyond the crest of the waves. The large hydrostatic pressures and shear stresses occurring at the interface modify the mechanical and chemical properties of the bond zone. Increases in hardness in this area have been reported by various authors.396 The defects along the interface can also cause a local increase of the chemical reactivity and thus might be expected to boost the etching rate. However, the effects of this preferential etching cannot be observed by light microscopy due to its inherently limited resolution power. The same limitation precludes the observation of morphological features directly along the bond interface as well as the interface itself. Furthermore, no information can be gained by light-

Jan 1, 1969

By D. C. Shelton

This paper discusses the metallurgical testing procedures and their applications at the laboratories and mills of Pima Mining Co. The author shows, using discussions and case histories, that routine sampling and evaluation of daily and monthly data can be as valuable as thorough laboratory investigations and mill test work. A great deal of valuable information can be made available this way. This paper discusses laboratory and mill metal-lurgical testing procedures and their applications at Pima Mining Co., located about 25 miles southwest of Tuscon, Ariz. The Company, incorporated in 1951 (the year the orebody was found) in California to operate the Pima mine, is jointly owned by Cyprus Mines Corp., Utah Contruction and Mining Co., and Union Oil Co. Milling started in December 1956. The main Pima orebody is a contact metamorphic vein of copper-bearing hornfels with an average dip of 45° to the south with an east-west strike. The hanging and footwalls are quartzitic pyroclastics (arkosite) containing some sulfides. Barren igneous intrusions are also present. Conglomerates and alluvial wash cover the deposit to a depth averaging about 200 ft. The principal copper mineral is chal-copyrite. Native copper, chalcocite, and minor amounts of chrysocolla and other copper minerals are also present, together with sphalerite and some molybdenite. Generally, it has been noted that the ratio of chalcocite to chalcopyrite is higher in the lower grade ores, while as the grade increases, there are only minor amounts of chalcocite. Open pit mining is employed at Pima, using both trucks and an inclined skiphoist system. A detailed description of Pima Mining Co. operations was presented by Spaulding et all. More recently another orebody to the north and east of the present pit has been discovered and will be placed in operation within a few years. This ore is of a porphyritic rather than a lode nature since values are disseminated in both igneous and metamor- phosed sedimentary rocks. The new orebody is expected to be harder and cleaner than the present deposit. The views expressed in this article are those of the author and do not necessarily reflect those of Pima Mining Co. nor of the profession in general. PlMA MILL The following outline of milling practice is presented to furnish a background for later chapters of this report wherein specific problems will be detailed and analyzed. Run of mine ore is crushed in three stages, using conventional equipment to 85% minus 1/2-in. for feed to two 10 x l6-ft rod mills operating in open circuit. Each rod mill discharge is split between two 10% x 13-ft ball mills in closed circuit with three 20-in. cyclones. In addition, a 7 x 12-ft ball mill with one 20-in. cyclone receives part of the discharge from one of the rod mills. This equipment was manufactured by Allis Chalmers and Equipment Engineers. The cyclone overflows are combined, sampled and, after joining the regrind cyclone overflow, are distributed into 12 10-cell Fagergren 66-in. flotation machines. The primary rougher concentrate produced

Jan 1, 1965