Search Documents

By I. Javandel, P. A. Witherspoon

The finite element method was originally developed in the aircraft industry to handle problems of stress distribution in complex airframe configurations. This paper describes how the method can be extended to problems of transient flow in porous media. In this approach, the continuum is replaced by a system of finite elements. By employing the variational principle, one can obtain time dependent solutions for the potential at every point in the system by minimizing a potential energy functional. The theory of the method is reviewed. To demonstrate its validity, nonsteady-state results obtained by the finite clement method are compared with those of typical boundary value problems for which rigorous analytical solutions are available. To demonstrate the power of this approach, solutions for the more complex problem of transient flow in layered systems with crossflow are also presented. The generality of this approach with respect to arbitrary boundary conditions and changes in rock properties provides a new method of handling problems of fluid flow in complex systems. INTRODUCTION Problems of transient flow in porous media often can be handled by the methods of analytical mathematics as long as the geometry or properties of the flow system do not become too complex. When the analytical approach becomes intractable, it is customary to resort to numerical methods, and a great variety of problems have been handled in this manner. One such method relies on the finite difference approach wherein the system is divided into a network of elements, and a finite difference equation for the flow into and out of each element is developed. The solution of the resulting set of equations usually requires a high speed computer. When heterogeneous systems of arbitrary geometry must be considered, however, this approach is sometimes difficult to apply and may require large amounts of computer time. The finite element method is a new approach that avoids these difficulties. It was developed originally in the aircraft industry to provide a refined solution for stress distributions in extremely complex airframe configurations. 27 Clough has recently reviewed the application of the finite element method in the field of structural mechanics.6 The technique has been applied successfully in the stress analysis of many complex structures.l, 27, 28 Recognition that this procedure can be interpreted in terms of variational procedures involving minimizing a potential energy functional7 leads naturally to its extension to other boundary value problems. In the field of heat flow, there recently have been introduced several approximate methods of solution that are based on variational principles.2-4, 17 By employing the variational principle in conjunction with the finite element idealization, a powerful solution technique is now available for determining the potential distribution within complex bodies of arbitrary geometry. In the finite element approximation of solids, the continuum is replaced by a system of elements. An approximate solution for the potential field within each element is assumed, and flux equilibrium equations are developed at a discrete number of points within the network of finite elements. For the case of steady-state heat flow, the technique is completely described by Zienkiewicz and Cheung.33 Since the flow of fluids in porous media is analogous to the flow of heat, Zienkiewicz et al. have employed the finite element method in obtaining steady-state solutions to heterogeneous and anisotropic seepage problems. 34 Taylor and Brown have used this method to investigate steady-state flow problems involving a free surface.25 The work of Gurtin has been instrumental in laying the groundwork for the application of finite element methods to linear initial-value problems.12 As a result, Wilson and Nickell have recently

Jan 1, 1969

By Robert J. White

Strong's equation for calculating bottom-hole pressure reduction due to gas cutting of drilling mud is corrected, resulting in a simpler equation which is easier to use. Use of the equation is illustrated by examples. It is shown that reduction of weight of a 10 lb/gal mud by 50 per cent at the surface due to gas cutting produces only n 3 per cent decrease in hydrostatic head at the bottom of a 5,000-ft well. It is also shown that at the surface 5 volumes of air per volume of mud are required to reduce the apparent mud weight from 8.5 to 6.5 lh/gal in a 3,000-ft well. Illustrative graphs are included to show the effect of various degrees of gas cutting on apparent mud weight at depths of 2,000, .5,000 and 10,000 ft and to show variation of apparent mud weight, with depth for a 100 lb/cu ft (13.37 lb/gal) mud gas cut to 90 lb/cu ft (12.03 lb/gal) at the surface. INTRODUCTION In 1938, Strong' published the following equation for calculating reduction in bottom-hole pressure due to gas cutting of drilling mud h = 1/D [p + pn/100 In p + p(1-n/100)/p(1- n-100)] where: h = depth in feet P = pressure in atmospheres at depth h due to mud column only D = hydrostatic pressure in atmospheres of a col-umn of uncut mud 1 ft high p = back pressure at well-head (in atmospheres) n/100 = fraction by volume of gas in mud at well-head at back pres-sure p This equation was recently found to contain an error due to an incor-rect expression for variation of vol-ume fraction of gas with pressure. Values calculated by the original equation are close to the correct values for small percentages of gas for which it was derived but become increasingly erroneous as the gas content increases and are completely unusable at the very high gas con-tents employed in aerated mud. DERIVATION The nomenclature used is the same as in Strong's paper. The pres-sure dP exerted by a lamina of thickness dh at a depth h ft is ex-pressed by Eq. 1 where x = volume fraction of gas at depth h dP = D (l - x)dh . . . (1) When we express x in terms of the wellhead per cent gas n, the well-head pressure p and the pressure P at depth h, the result is Eq. 2. x = (np/p+p)/(100-n) + (np/P + p) When this is substituted in Eq. 1 and rearranged to separate the var-iables the result is dh = 1/D [dp + np/100-n dp/(P + p]. Integration between appropriate lim-its results in or if the wellhead is open so that p = 1 atm and we rearrange Eq. 4, the result is loss in head = hD — P = n/100-n In (P + 1) ...(5) Eq. 5 can be solved easily by successive approximation using hD as a first approximation for P on the right-hand side and calculating a first value for loss in head. This can then be used to get a new value of P using the left-hand side of the equation. Values converge very rap-idly even for quite large values of per cent by volume gas n. EXAMPLES The effect on bottom-hole pressure of 50 per cent gas cutting of the mud in a 5,000-ft well using 10 Ib/ gal mud will be calculated, we have: h = 5,000 ft 10 X 7.48 144 X 14.7 = 0.0353 atm/ft hD = 176.5 atm n = 50 Substituting these values in Eq. 5 and using hD as a first approxima-tion of P on the right, we have, approximate loss in head = 50/50 In (176.5 + 1) = 2.30 log 177.5 = 5.17 atm. We calculate a new value of P as follows:

Jan 1, 1958

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By P. B. Elkin, K. C. Ten Brink, Allen D. Garrison

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940

By K. C. Ten Brink, Allen D. Garrison, P. B. Elkin

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company's Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By J. W. Clark, C. T. Sims

Wrought chromium-base alloys containing yttrium, cubic monocarbides of the Ti(Zr)C type, and similay alloys containing manganese and rhenium have been melted and fabricated. Strength has been studied by hot hardness and elevated-temperature tensile and rupture measurements, low-temperature ductility by tensile testing, and surface stability by oxidation testing. In additiod, studies have been conducted of the carbide stability, and of aging behavior. The carbide dispersion generates effective elevated-temperature strength, which is further enhanced hv strain-induced precipitation. The dispersion exhibits classical dissolution and aging response. The ductile-to-brittle transition temperature of these alloys is above room temperature. The alloys reported show fairly good oxidation resistance, but nitrogen contamination can cause fortnation of a hard Cr2N layer under the oxide scale. Manganese does not appear to be a promising alloying element in chromium. In the years 1945 to 1950, the metal chromium was considered as a possible base for alloy systems due to its considerably higher melting point than superalloys, its low density, its high thermal conductivity, and its apparent capacity for strengthening. However, this interest in chromium was short-lived. It was found difficult to melt and cast, to be exceptionally sensitive to the effect of minor imperfections, to have a lack of ductility at both room and elevated temperatures, and to be subject to a deleterious effect of alloying elements upon the ductile-to-brittle transition temperature.' Since then, chromium, as a practical alloy base, has remained virtually unstudied. Further, purposeful ignoring of chromium has been promoted by statements that its bcc structure would not allow it to be strengthened to useful values, when compared to the "austenitic" alloys.2 Recently, a new look has been taken at chromium-base alloy systems. Study of the literature will show that chromium, providing some of its disadvantages could be eliminated or minimized, actually has a rather attractive potential as an alloy-system base. Analysis of rather scattered data suggests that chromium is quite capable of being strengthened to high levels. Also, significant strengthening of its two sister elements in Group VI-A, molybdenum and tungsten, has been demonstrated in a number of commercial and exploratory alloys. Chromium should be similar. Since chromium does not readily form a volatile oxide like tungsten or molybdenum, it offers a much higher probability of giving birth to alloy systems with useful oxidation resistance. Concerns about possible high elemental vapor pressure have been mitigated by recent data.3 In addition, the physical properties exhibited by chromium are attractive for application as a high-temperature structural material. For instance, its thermal conductivity varies from 49 to 36 Btu-ft/hr-sq ft-°F over its range of usefulness (which is two to four times higher than most superalloys), its density is about 7.2 g per cc (20 pct less than most nickel-base alloys), its coefficient of thermal expansion varies from 4 to 8 x 10-6 per OF, and it has a relatively high modulus of elasticity, approximately 42 x 10' psi.4 Alloying studies on a chromium base in the past have usually encompassed rather sweeping solid-solution alloy additions for strengthening. This is not consistent with contemporary alloying practice in Group VI-A. For instance, molybdenum, also in Group VI-A, is primarily alloyed for strength improvement by use of heat-treatable carbide dispersions.5 Chromium and molybdenum are similar in their chemical activity and other properties. Thus, strengthening of chromium by carbide dispersions was studied. Chromium-base alloys are plagued with room-temperature brittleness, although high-purity unal-loyed chromium can be made ductile.4,8 Use of yttrium as a scavenger has done much to improve ductility and resistance to nitrogen embrittlement in chromium systems,7 so it was utilized in this program. It has also recently been found8 that small rhenium additions (1 to 5 pct) create improvement in the ductility of Type 218 tungsten wire. This is apparently related to the remarkable effect of rhenium additions near its terminal solid solubility in all Group VI-A metals.9'10 Investigation to establish if dilute concentrations of rhenium would also be effective in chromium appeared to be logical for this program. Since rhenium is too expensive to be practical in alloys for application as structural components, ductility improvements through solid-solution alloying were also sought by substitution of manganese for rhenium; manganese, like rhenium, exists in Group VII of the periodic system. The optimum amount of carbide dispersion for chromium-base alloys was obtained by analogy with molybdenum. Strengthening in molybdenum is achieved by use of Ti-Zr carbide dispersions. A

Jan 1, 1964

By Wilson T. Lundy

The history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur CO. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico. Terrain Characteristic of the delta region, the terrain consists of a low, flat, uninhabited area of marsh land intersected by many shallow lakes and bayous. With the exception of salt grasses, the region is devoid of vegetation and presents, in all directions, an unobstructed path to the vagaries of the winds. The general character of this area can be best visualized from the mechanism of its formation.' Offshore bars formed enclosing long narrow lagoons between the bar and the inner shore line, the lagoons communicating with the sea by means of tidal inlets. The water in the lagoons, being comparatively quiet, favored the deposition of fine debris composed of sand carried into the lagoons by action of the waves, tides and river-borne sediments from the land surface. As this material accumulated the bottoms of the lagoons were built up and eventually salt grasses obtained a foothold. The successions of growth and decay of these grasses formed a brown fibrous mat varying in depth from a few inches to several feet. This mat of vegetation virtually floats on an ooze that is several feet thick and is composed of alluvial sediments and very fine sand, and the whole is underlain by an unctuous clay. The decayed vegetation from the upper layer when dried has a peaty appearance.

Jan 1, 1934

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be compared with field work. The same applies to geological contacts. Once these have been 3stablished at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By R. F. Yap, N. Arbiter, C. C. Harris

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give substantially constant power numbers in liquid systems indicating that they operate close to fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufacturers. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles, drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations. The modern mechanical flotation machine has, over a period of 60 years, displaced other designs to become the dominant type. Once the correct chemical environmental conditions have been established, the major requirement, selective mineral-air adherence, is essentially a function of two operating variables — impeller speed and air rate. The special nature of this dependence is such that in the same apparatus, but under different operating conditions, adherence can be either prevented or destroyed. Another aspect of this observation is that flotation machines though differing in detail to a considerable extent can produce similar metallurgical results. It must be concluded that having determined the correct reagent levels, establishing the correct operating conditions are at least as important as machine design. Since about 1960, after 30 years of fairly stable circumstances, manufacturers have been developing new types of machines whose major feature is emphasis on pulp flow characteristics by virtue of new im-peller-stator designs. As far as can be ascertained, these new designs necessitate radical departures from accepted impeller speed-air rate values. Performance data are still awaited. Flotation machine development has been empirical, as is selection of operating conditions. The purpose of the work at Columbia University has been to elucidate the fundamentals of the subject so that the purely mechanical aspects of the flotation process can be understood in hydrodynamic terms.1-6 Hopefully, this might lead to intelligent selection of a particular machine and its operating conditions for a specific ore based on a minimum of testing, or even to new types of flotation machines. The present investigation is the most comprehensive to date.7,8 Earlier work, which was largely exploratory, has been repeated and extended and employes the most accurate measuring techniques available. Additionally, sufficient hydrodynamic data were obtained under flotation conditions to delineate the relevant operating ranges. Attention has been given to scaling in that several geometrically scaled tanks and impellers have been constructed and tested; it has been pointed out elsewhere that undistorted geometrical scaling rarely pertains in flotation machine design.5 This paper is divided into sections dealing with relevant combinations of the three phases: liquid, air and solid. Summaries of the literature have been given in previous publications2-4 and will not be repeated here. Recently, several reviews of mixing have appeared, which can be usefully referenced.9-11 It is of interest to note that flotation is not included

Jan 1, 1970

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received little study on the part of wire mills, particularly those that have commenced operations in the last few years. Two Types of Defects One type of defect is generally known in this country as "check marks;" in Europe it is termed "crowfeet" (Fig. 1). This defect occurs in the surface of the copper wire, in the form of V's, which are always

Jan 1, 1930

By L. H. Levenson, Charles S. Barrett

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Charles S. Barrett, L. H. Levenson

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By M. E. Lombardi

ThE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 81/4 in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling. The problem is to reach a depth of 4,000 ft. or more with a string of

Jan 1, 1915

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publi-cations of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photo-graphs are used on such scales as soon to 1/5,000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are inter-preted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By S. M. Marshall, B. M. Bird

For a number of years European investigators have used laboratory methods of predicting the probable strength of coke made from coal, and recently several investigators in the United States have reported the use of various tests for this purpose. There is at present no method accepted as standard, however, nor is there even agreement as to the general type of test that should be used. Furthermore, because the details of most of the tests have not been worked out carefully, one investigator can not hope to duplicate the work of another. The extension of coke manufacture to new localities in the United States, and the increasing need for cokes of exceptional qualities made from the most economical mixtures, made it desirable to have some simple laboratory test which will determine whether given coals, alone or blended with other coals, are more satisfactory from the standpoint of coke strenpth- than others of different cost. The work described herein has resulted in the development of a simple laboratory test which, it is believed, can be generally adopted in coal laborat,ories, and which will give concordant results even though performed by different investigators in different laboratories. The general method of predicting whether a coal or a mixture of coals will produce a strong coke, resistant to crushing and shattering, has been to correlate the known strengths of the cokes produced in commercial ovens with some measurable constituent or with some property of the coals, and then to use the relationship so found for forming an estimate of the coking strengths of coals unknown. Several such correlations have utilized the percentages of the various ultimate constituents of coal, such as the oxygen content and the hydrogen-oxygen ratio;(39)§ other correlations have involved the proportion of a, B and r com-pounds, (17,21,30c) or of "oil and solid bitumens."(16,30) Also a relationship has been traced between the coking properties of coal and the rate of change of the resistance offered to the flow of an inert gas by fine particles of the coal while being slowly heated. (11,176) But the most general corre-

Jan 1, 1930

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969

By P. Payson

Intergranular corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinnüberl suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain3 say that "intergranular attack—may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small percentages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion. and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By D. L. H. Forbes

(New York Meeting, February, 1912.) Introduction.. THE application of the cyanide process to complex sulphide ores for the extraction of their bold and silver is no longer a novelty, but, as an example showing modern tendencies in this direction, the following description of the new milling process at the Lucky-Tiger mine is offered: The extraordinary richness of the ore in the upper workings of this mine made any thought of milling in its early hays seen unnecessary. Its location in an almost inaccessible part of the rugged mountains just south of the Arizona boundary-line, and 60 miles from the town of Douglas, made the expense of bringing in machinery and supplies a very serious consideration. But, after the property had been shipping high-grade ore on mule-back for a few years, there remained in the mine a considerable tonnage of vein-matter that was too low in value to ship, but which it was thought could be milled near the mine at a profit. The first milling-experiment consisted in the installation of Nissen stamps in conjunction with concentrating-tables and Frue vanners, but, as the ore from the upper workings contained most of its silver in the form of cerargyrite, this type of mill was not successful. The proximity of the mine to the great copper-concentrating mills of Cananea and Moctezuma naturally made the influence of copper-milling, ideas felt in the company's next installation. At considerable expense a stage-crushing concentrating-mill, with a capacity of 100 tons per day, was built. This mill was modeled along the lines of the most approved practice in copper-concentrators at that time, the main idea being that crushing by stages in rolls was necessary in order to prevent losses from ?sliming." Largely owing to the fact that, when the mill

Aug 1, 1912