Search Documents

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter' on lead, and Vandermeer and orddon' on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.' Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.'' Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By Theron Wasson

Michigan produced 16,637,000 bbl. in 1937. This makes it a record year in the history of Michigan's oil industry. During the year 953 wells were completed; 779 within the limits of established fields and 174 wildcats; 616 new oil wells, 68 gas wells and 269 dry holes. Table 1 has been arranged in alphabetical order of field names. Production figures for 1936 have been corrected because December figures were estimated. In this year's summary, December production is based on actual reports. The Leaton and Mt. Pleasant fields have been re-defined. Mt. Pleasant production north of the south line of Denver township, Isabella County, has been included with Leaton in accordance with usual practice in Michigan. The locations of fields discovered since the last map was published1 are shown in Fig. 1. Activity during 1937 Buckeye Field.—The Buckeye field of Gladwin County was the center of greatest activity during the year and was responsible for the increase of 4,700,000 bbl. over the state total for 1936. Buckeye produced 6,428,-000 bbl. in 1937. In this field 328 producing wells were completed during the year—over one-half the oil producers drilled in the state. Buckeye was subject to voluntary and cooperative proration from April 1 to the end of the year. Other pools of the state were not prorated. The new production at Buckeye is from porous Dundee limestone of Devonian age, similar to the older fields. Other New Fields.—The Sherman field was second in importance as a source of new production, with a total of 1,532,000 bbl. Salem township, Allegan County, on the southwest side of the Michigan Basin, was developed during the year. Production at Salem is from the Traverse limestone at a depth of 1600 ft., and 52 producing wells have been drilled in this pool. Other active pools were Clayton and Adams townships, Arenac County. The Bentley pool, discovered in October 1937 southeast of

Jan 1, 1938

By Sylvan Cromer

THE need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investi-gators1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happen-ings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quanti-tative results for air-water flow. EXPERIMENTAL APPARATUS AND PROCEDURE The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1939

By Edwin C. Holden

In making the original estimates for a report recommending the cyanidation of Ymir stamp-mill tailings, the writer was unable to find in any of the standard works on cyanide-practice certain data applicable to the local conditions; nor has he as yet seen quite the same practice recorded in the rapidly growing literature of cyanidation. To present these figures, together with a few novel features of local practice, the present paper is offered. The ore treated is obtained from a fissure-vein of steep dip, occurring in a slate country. The ore-body is lenticular in plan, swelling from 4 ft. in width at one end to a maximum of 42 ft., and tapering irregularly to less than 18 in., where payvalues cease. In the wider portions of the fissure the ore is mixed with more or less horse-matter from the walls. The clean ore is white, massive quartz, with from 8 to 12 per cent of sulphurets; the latter being pyrite, sphalerite and galena, the predominance being in the order given. The precious metal tenor is variable, the gold more closely following the pyrite, the silver the galena. The present mill-supply is practically all from below the oxidized zone. The unavoidable admixture of horse-matter and stope-filling with the ore as mined, affects more or less the character of the mill-feed, which sometimes contains from 10 to 25 per cent of slate. During the last three months of 1902, the mill-feed carried 0.3977 oz. gold and 1.903 oz. silver per ton of 2,000 lb., 2.65 per cent lead and 2.92 per cent zinc. The iron, unfortunately, was not determined. The Ymir mill and mine have been fully described elsewhere;* suffice it to say of the milling that the crushed ore,

Jan 1, 1904

By B. D. Cullity, K. S. Sree Harsha

When a copper or aluminum single crystal is swaged into wire, the resulting deformation texture depends on the original orientation of the crystal. The<100> and <111>orientations me essentially stable, while <110> is unstable. The greater the <100> content of the deformation texture, the stronger the wire is in torsion. the greater the<111>content, the stvonger it is in tenszotz. The preferred orientation (texture) of fcc wires, either after deformation or recrystallization, is usually a double fiber texture in which some grains have <100> parallel to the wire axis and others have <111>. The relative amounts of these two texture components, as reported by different investigators for the same metal, vary considerably. Previous work in this laboratory&apos; has shown that the starting texture of a wire, i.e., the texture which it has before deformation, can have a decided influence on the texture produced by deformation. In particular, it was found that the deformation texture of copper wire is essentially a single <100> texture, if the wire before deformation contains only a <100> component. This is true even when the deformation is carried to more than 98 pct reduction in area. This paper reports on further studies of the role played by the starting texture. Copper and aluminum single crystals of various orientations have been cold swaged into wire, and quantitative measurements of the resulting deformation textures have been made. The tensile and torsional properties of the deformed wires have also been measured, and the relation between these properties has been correlated with the texture of the wire. These measurements were made in order to demonstrate that a cold-worked wire can be made relatively strong in torsion and weak in tension, or vice versa, by proper selection of the texture before deformation. MATERIALS The copper was of the tough-pitch variety, containing, by weight, 99.962 pct Cu, 0.003 pct Fe, 0.025 pct 0, and 0.0021 pct Si. The aluminum contained more than 99.99 pct .&apos;41; the only reported impurities were 0.001 pct Fe, 0.001 pct Si, and 0.003 pct Zn, by weight. Large single crystals of these metals were grown by the Bridgman method in graphite crucibles and a helium atmospliere. Cylindrical specimens of predetermined orientation, about 1.5 in. long and 0.36 in. in diameter, were machined from the as-grown crystals and then etched to 0.25 in. to remove the effects of machining. Their orientations were checked by back-reflection Laue photographs, and they were then swaged to a diameter of 0.050 in. (96 pct reduction in area). 111 order to study the "inside texture" of the deformed wires, they were etched, after swaging, to a diameter of 0.040 in. before the texture measurements were made. TEXTURE MEASUREMENTS The fiber texture which exists in wire or rod can be represented by a curve showing the relation between the pole density I, for some selected crystal-lographic plane, and the angle $ between the pole of that plane and the wire axis (fiber axis). Such a curve will show maxima at particular values of , and these values disclose the texture components which are present. The relative amounts of these components can be determined2&apos;3 from the areas under the maxima on a curve of I sin F vs F. It is seldom necesszlry to measure I over the whole range of F from 0 to 90 deg, since the existence of maxima in the low-F relgion can be inferred from measurements confined to the high-F region. The X-ray measurements were made with a General Electric XRD-5 diffractometer and filtered copper radiation, according to one or the other of the following procedures: 1) A method developed in this laboratory,4 involving diffraction from a single piece of wire. 2) A modification of the Field and Merchant method.5 This method was originally devised for the examination of sheet specimens, but it can easily be adapted to the measurement of fiber texture. Three or four short lengths of wire are held in grooves machined in the flat face of a special lucite specimen holder. The axes of the wires are parallel to the plane defined by the incident and diffracted X-ray beams, and the holder to which the wires are attached can be rotated step-wise about the diffractometer axis for measurements at various angles 9.

Jan 1, 1962

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis&apos; criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis&apos; conclusions and with improvement of ballmilling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By Arthur Anderson

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Inno-vations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these fea-tures that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort. was made to use heavy truck haulage in the trans-portation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By A. Szirmae, Hsun Hu

The early stages of recrystallization in a 70 pct cold-rolled Si-Fe crystal of the (110) (0011) orientation were studied with a Siemens electron microscope. Orientation studies based on electron-diffractzotz. patterns confirm the results of previous texture analysis. The driving energy for recrystallizatior and the critical radius for growth were calculated from the dislocation energy and the energy of the subgrain bourzdaries, and it was found consistent with the observed size of the recrystallized grains. The recrystallization characteristics of crystals with different initial orientations are discussed. The recrystallization of cold-rolled (110)[001] crystals of Si-Fe has been widely studied by various investigators.1-4 Their results on both deformation and annealing textures are in good agreement. The rolling texture after 70 pct reduction consists mainly of two crystallographically equivalent (111) [112] type textures and a minor component of the (100) [011] type. The latter is derived from the deformation twins, or Neumann bands, which are formed during the early stages of deformation and later rotate to the (100) [011] orientation upon further rolling reduction. Between the two main (111) [112] type textures, there is some orientation spread, because of which very low intensity areas appear in the pole figure. If these very low intensity areas are considered to be a very weak component in the texture, then a (110) [ 001 ] orientation may be assigned to them. When this rolled crystal is annealed at a sufficiently high temperature for recrystallization, the texture returns to a simple (110) [001]. The purpose of the present investigation was primarily to seek a better understanding of the recrystallization process by using the electron transmission technique. The (110) [0011 type of crystal was selected because orientation data for it are well known from previous studies with conventional techniques. Direct observations on the recrystallization of such a crystal have also been made by using a hot-stage inside the electron microscope, and the results will be reported in another paper. MATERIAL AND METHOD A single-crystal strip of the (110) [001] orientation was prepared from a commercial grade 3 pct Si-Fe alloy by the strain-anneal technique.= The strip was approximately 0.014 in. thick, and was rolled 70 pct at room temperature to a thickness of 0.004 in. Specimens were cut from the rolled strip and were annealed in a purified hydrogen or argon atmosphere. They were then electrolytically polished in a chromic-acetic acid solution to very thin foils. Best results were found by polishing first between two narrowly spaced flat cathodes with the specimen edges coated with acid-resisting paint, followed by polishing between two pointed electrodes until a hole appeared in the center as described by Bollmann.6 It was found that a thin transparent film always formed along the thin edges of the polished specimen. This film was then removed by rinsing the specimen very briefly in a solution of alcohol with a few drops of HF or HCl. RESULTS AND DISCUSSION 1) The Deformed Crystal. From the electron-diffraction patterns taken at various areas of an as-rolled specimen, the texture components as deduced - from ordinary pole-figure analysis were confirmed. Over most of the areas where orientation was examined, a (111) pattern with a [112] direction parallel to the rolling direction was obtained. This corresponds to the main deformation texture of the (111) [112] type. In a few areas the diffraction pattern was (100) [Oil], corresponding to the minor-texture component derived from the Neumann bands. The (110) [001] orientation, which corresponds to the very weak intensity area in the pole figure, was found infrequently. A typical example of the deformed matrix having the (111) type main texture is shown in Fig. 1, where (a) is the microstructure and (b) is the diffraction pattern taken from that area. It was also frequently observed that in other areas more or less continuous rings of weaker intensity were superimposed on the simple (111) diffraction pattern, suggesting the presence of a wide range of additional orientations. Other evidence indicated that the recrystallization characteristics are different in these two different types of areas. The hot-stage observations which provide this evidence will be discussed in another paper. AS shown in Fig. l(a), numerous dislocation-free areas of very small size are embedded in the "clouds" of high-dislocation density. This indicates that the deformation of a single crystal, even after a rolling reduction of 70 pct, is far from uniform on a micro-

Jan 1, 1962

By A. W. Ross, William Marsh Baldwin, T. S. Howald

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip&apos;-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves&apos;5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By William Marsh Baldwin, T. S. Howald, A. W. Ross

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip&apos;-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves&apos;5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By Ezequiel Ordonez

MOST spectacular of Nature&apos;s contributions to the making of the postwar world is the Paricutin volcano, in Mexico, which I described in the July issue of this magazine last year, a few months after it was born. Now, after more than a year of continuous eruption, it is still and perhaps will remain a comparatively small though no less interesting volcano. The cone on April 1 had an altitude of nearly 1200 ft. above the level of the small flat field from which it began to grow on Feb. 20, 1943. This cone is now almost entirely surrounded by the lava flows that poured out at different dates, from its base or from outlets on the slopes near its base. To the north and northwest these lavas were

Jan 1, 1944

By V. I. Purcell, R. E. Snow, S. C. Sun

FATTY acids have been used as standard collectors for floating the matrix1-8 but not the leached zone phosphate ores. After a series of investigations, Davenport9 and Tarbutton10 concluded that the Florida leached zone ores tested were unamenable to fatty acid flotation and must be upgraded by floating the siliceous gangue with Armac-T as collector. The cationic flotation was estimated11 to cost almost ten times as much as a fatty acid process that would ideally give the same flotation grades and recoveries of phosphates. Mineralization: Extensive deposits of leached zone aluminiferous phosphate occur in The ore sample used for this work was obtained from the Virginia-Carolina Chemical Corp., Clear Springs area, Florida. The ore is a potential source of uranium and aluminum as well as phosphorus. Since the uranium and the recoverable aluminum are contained in some of the phosphate minerals, an upgrading of phosphate results in a corresponding enrichment of both uranium and aluminum. The phosphate minerals in the ore are primarily pseudo- wavellite, millisite, and carbonate fluorapatite, with a minor amount of wavellite. Quartz and clay are the common gangue minerals, quartz being pre- dominant. Others present in small amounts are ilmenite, hydrated iron oxides, staurolite, monazite, and zircon.

Jan 1, 1957

By Porter W. Shimer

(New York Meeting, February, 1912.) IT does not seem to be generally known that some American pig-irons contain notable amounts of vanadium, and while the present investigation is far from covering the whole range of irons, it is hoped that, at least, it may serve to call attention to the importance of looking for this element. The majority of the pig-irons investigated were made in the Lehigh Valley and neighboring furnaces, using more or less New Jersey magnetite in their mixtures. Many of these ores, and probably all of them, contain a little vanadium as well as titanium; the ore from one of the largest of these mines contains 0.05 per cent. of vanadium and 0.60 per cent. of titanium. Dr. Thomas M. Drown was the first to detect the presence. of vanadium in the incrustations 1 occurring on certain pig-irons, and he also found this element in a number of magnetites, but the methods for its accurate determination had not, at that time, been well worked out. In a general way, it may be said that the Lehigh Valley pig-irons contain from 0.02 to 0.05 per cent. of vanadium and from 0.10 to 0.20 per cent. of titanium. These elements follow the silicon; that is, the furnace-conditions which produce a high-silicon, low-sulphur iron will cause the maximum reduction of vanadium and titanium, and the lower grades of iron, with low silicon and high sulphur, have a lower content of these elements. The following analyses of irons made from the same mixture, but under varying furnace-conditions, show this very well Vanadium. Silicon. Sulphur. Per Cent. Per Cent. Per Cent. NO. 1 X, . . . 0.042 3.46 0.022 No. 2 plain, . . 0.038 2.26 0.041 Mottled, . . . 0.0&apos;29 0.52 0.106 1 Robertson and Firmstone, Note Concerning Certain Incrustations on Pig Iron,Trans., xii., 641 (1883-84).

Aug 1, 1912

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By B. W. Christ, P. M. Giles

Mossbauer effect measurewents have been made on I-mil-thick foils of commercial 1 wt pct C steel and Fe-2 wt pct C alloy. The experimental method required about 3 to 5 vol pct of a phase in the nzultiphase steel sample for detection. Room-temperature Md&apos;ssbauer patterns obtained on austenitized atid quenched samples exhibit fifteen, and possibly twenty-one, lines. A sharp parama&tetic singlet and a quadrupole doublet, poorly resolued from the singlet, are attributed to austenite. Remaining lines are due to tnartensite. Accurate evaluation of austenite line paranzeters is not feasible if significant amounts of other phases such as carbides or martensite occur simultaneously with austenite. This is demonstrated by comparison of hyperfine interactions determined for austenite in multiphase high-carbon samples with those reported for Fe-C austenite in a nearly 100 pct austenitic sanple. Lines from carbides are incompletely resolced from austenite lines, as demonstrated by comparison of austenite line positions with carbide line positions calculated frow published values of hyperfine interactions. One martensite line overlaps an austenite line in the pattern for commercial 1 wt pct C steel. Results of this study suggest that the usefulness of e M6ssbauer pectroscopy for quantitatizle analysis of austenite in bulk samples of quenched and tempered high-carbon steels is restricted by poor resolution. Use of Mossbauer spectroscopy for phase identification and for evaluation of atomic and electronic structures appears quite feasible, however, The Mijssbauer effect has been widely discssed,&apos;-and e Mossbauer effect measurements have been reported on materials of metallurgical interest.7"20 In particular, it has been proposed that e Mossbauer patterns of commercial steels and laboratory-made Fe-C alloys, in the quenched condition, are composed of lines originating in two phases, Fe-C austenite and Fe-C martenite.-&apos; Evidence accumulated in this study demonstrates that three absorption lines found in the central region of the e Mossbauer pattern obtained on quenched steels are attributable to retained austenite. This interpretation is supported by parallel decreases in the intensity of these three lines caused by subambient cooling of commercial 1 wt pct C steel samples after water quenching to room temperature. A second result of this study is to clarify effects of line resolution and sensitivity in the Mossbauer patterns of multiphase steels on the accu- rate determination of austenite line parameters. Experimental line widths (full width at half height) are generally 1.5 to 3 times larger than the natural line width of 0.19 mm per sec. At least two lines, and sometimes more, from a single phase such as cementite (Fe3C), other carbides, martensite, and austenite fall in the energy band, i0.85 mm per sec. hhis band width is employed simply for convenient reference. It represents approximately the energy interval between the + 112 to 112 transitions in ferrite and is expressed as the velocity needed to Doppler shift a 14.4kev 7 ray to the aforementioned ferrite energy levels. This energy band is referred to as "the central region of the Mossbauer atttern:: in this paper. Hence, due to the large number of lines from different phases in a multiphase steel falling in a relatively narrow energy band, absorption lines from the different phases may overlap. Analysis of available data, presented below, indicates that this occurs to a significant extent for phases which commonly occur in quenched and quenched and tempered high-carbon steels. One consequence of limited resolution in the Mdssbauer patterns from multiphase steels is difficulty in accurate determination of such line parameters as position, width, and intensity. In fact, it appears that quantitative analysis for retained austenite in quenched and tempered high-carbon steels is not practical with the present experimental method. Line resolution is influenced to some extent by sensitivity. We point out below that atom or volume fractions of less than about 3 to 5 pct are not detected by the present experimental method. Thus, the presence of a multiplicity of phases does not always lead to impaired resolution. Finally, we report in this paper room-temperature MGssbauer parameters determined for austenite in a freshly quenched, commercial 1 wt pct C steel and in a freshly quenched laboratory heat of an Fe-2 wt pct C alloy. These parameters are compared with others reported in the literature. Three types of hyperfine interactions are detectable in a Mossbauer effect measurement: isomer shift, quadrupole interaction, and magnetic dipole interaction. These interactions are evidenced by one, two, and six line patterns, respectively.&apos;-4 More than one type of interaction has been reported in certain metallurgical phases thus far studied by this method. Isomer shift is the experimentally measured displacement of line position from some arbitrarily defined reference position. In the case of a multiline pattern, isomer shift is given by the displacement of the centroid (center of gravity) of that pattern from the reference position. All isomer shifts measured at finite temperatures contain a second-order Doppler effect characteristic of that temperature. The isomer shift is related to the total s electron density at the nucleus, becoming more negative with increasing s electron density. The first-order quadrupole effect arises from the interaction between the nuclear quadrupole moment and any axially symmetric electric field gradient in

Jan 1, 1969

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By A. W. Hahn

ALTHOUGH enormous tonnages of sulfide lead and lead-silver ores are treated by flotation, the products of flotation mills treating oxidized ores of lead and silver are almost negligible. However, each year there is a slight tonnage increase, and it is possible, should a sizeable oxidized lead ore tonnage be developed, the field will become an important one. In 1918, the Shattuck-Arizona Copper Co. erected a plant at Warren, Ariz., for the treatment of oxidized gold-silver-lead ores. Glenn L. Allen worked out the metallurgy for this plant, employing tabling, followed by flotation concentration. The Shattuck-Denn Mining Co., successors to the Shattuck-Arizona Co., now employs straight flotation in the same mill, treating about 200 tons daily. In 1922, the San Diego mill of the American Smelting & Refining Co., in the Parral district, Chihuahua, Mexico, started operating a 600-ton mill on a mixed sulfide-oxide gold-silver-lead ore. Tables and flotation are used here, and about 200 tons of oxidized slime treated by flotation. In 1923, the Eureka Holly Mining Co. started operating a 90-ton mill at Eureka, Nev., using tables and flotation, on an oxidized lead-silver ore. In 1924, the American Smelting & Refining Co. started a 250-ton mill in northern Peru, to treat a high-grade oxidized gold-silver ore with very low lead values. In 1924, the Grand Central Mining Co. started a 200-ton flotation mill on old oxidized gold-silver-lead tailings at Fairbank, Ariz. In 1926, the Compania Internacional Minera, a subsidiary of the Union Corporation of London, started a 250-ton flotation mill on oxidized lead-silver ores, and during April of this year, the Phelps-Dodge Corpn. will probably start a 250-ton mill at Warren, Ariz., on oxidized lead-silver ores, similar to those being treated in the Shattuck-Denn mill. METHODS All of these mills use sodium sulfide for filming the oxide minerals, with the possible exception of the North Peru mill, and all use oily reagents. The total tonnage of strictly oxidized lead-silver ores concentrated by flotation is probably less than 2500 tons daily. The following figures give the various types of ores being treated:

Jan 1, 1928