Search Documents

By J. B. Goddard

The discovery of rhenium on the ion exchange resin used at the uraniun in-situ leach operations at Palangana, TX, led to a laborabory study of possible recovery methods. Rhenium was present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, ReO4-. It concentrated on the anion exchange resin, which was a factor of 10 more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the per-chlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3N or stronger concentration of nitrate containing up to 0. 5N H + was found to be the system of choice. A rhenium sulfide concentrate containing up to 14010 Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4ReO4 followed by hydrogen reduction at elevated temperature.

Jan 1, 1984

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By William L. Zeller

IN the past 75 years industrial engineering has been highly developed in many fields, but the coal mining industry has just begun to realize its potential for cutting costs. To receive the maximum benefit, a company should apply industrial engineering from the time a new installation is contemplated, but the principles can also be used to reduce and control the costs of an established operation. One company that had been mechanized for seven years reduced its total labor cost 57 pct by industrial engineering. Of this reduction, 20 pct was brought about by a preventive maintenance, rebuilding, and scheduled lubrication program that eliminated 80 pct of the delay caused by mechanical and electrical failures. Thirty percent of the cost reduction was attributed to rearranging the work force into crews of the most effective size, changing working methods, and training all mine supervision in the principles of the cost reduction program. The remaining 7 pct reduction was brought about by a wage incentive program for all the men in the mine. The productivity of this coal mining operation was increased from less than 8 tons per payroll man to 20 tons. This increased productivity was brought about while using the same equipment, men, and supervision.

Jan 12, 1957

By John E. Miller

The Miller Number System is a well established method of measuring the relative abrasivity-friability of slurries, resulting in data that can be used in the selection of pump type and in forecasting wear-life of pumps and pipelines in slurry service. 1,2 Then after the pump type is selected, a Flow Analysis is determined by computer using pump design and operating parameters. This is used to determine pulsation control, suction requirements and stabilization, etc.

Jan 1, 1977

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it-is felt that a description, of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By R. J. Evans, A. G. Revesz

Silicon films have been grown by chemical reaction on (111) silicon substrates. The surfaces were examined by various microscopic and interfero-metric methods. Surface structures are classified into two groups depending on whether the angles between the bounding planes and the (111) surface are small (<3 deg) or large (> I0 deg). A layer-gvowth mechanism is postulated to explain the topography and the influence of growth parameters. Growth proceeds by lateral expansion of the (111) layers in (211) directions, thereby forming steps. The step edges are perpendicular to the direction of expansion and are thus along (110) directions. Step bunching md surface nucleation both play an important role in modifying the flow pattern and in the step regeneration. These are influenced ver?) much by impurities, especially oxygen. Although the growth is a result of a surface-controlled ga: reaction, it is very similar to growth from an impure solution. OVERGROWTH ("epitaxial growth") of silicon is important and widely used. During the past years several investigators have observed various topographical features or so-called faults on the grown films. A study of the surface morphology gives some insight into the growth mechanism. I) EXPERIMENTAL Silicon films have been grown on silicon substrates by a method described by Theuerer.&apos; Silicon is formed by reduction of SiCl, in hydrogen. The rate of incidence of SiC1, was varied between 5 x 10"6 and 2 x 10&apos;4 moles min-&apos; cm-&apos;. The mole fraction of Sic4 in the Hz-SiCL mixture was about 5 x X Both the rate of incidence and the mole fraction were calculated on the assumption that the Hz bubbling through the SiC1, reached equilibrium saturation. Assuming uniform velocity distribution, the linear velocity of the gas in the reactor tube was estimated to be 2 cm sec-l. The temperature of deposition was varied between 1070" and 1260°C. Chemically polished p-type silicon wafers of 20 to 100 ohm cm resistivity were used as substrates. These were within 1/2 deg of a (111) orientation. The thickness of the grown n-type film was determined by two methods: a) measurement of the depth of the p-n junction taking into account the junction shift due to diffusion, b) measurement of the traces of stacking-fault tetrahedra on the (111) plane.&apos; The agreement between the two methods was better than 20 pct. The rate of growth varied between 0.2 and 4.0 pmin-&apos;. The formed films were examined by reflection and light-section microscopy, and by multiple-beam interferometry. Phase-contrast illumination revealed height differences of about 30A. For measuring heights greater than 1 p a light-section microscope3 was used. The resolution by multipke-beam interferometry4 was between 50 and 100A. Crystallographic directions on the surface were determined by X-ray and from the orientation of etch pits and stacking faults as revealed by Dash etch (I part HI?, 3 parts HNOJ, and 12 parts CH3COOH). Some specimens have been investigated by electron microscopy. Platinum-shadowing and carbon-replica techniques were used to show the fine topography and reflection diffraction to determine the structure of the grown layers. 11) RESULTS The topographical features can be classified into three groups. he first group is comprised of fine ridges (striations). The second group consists of structures, which are bounded by planes making angles of less than 3 deg with the (111) surface. They are, therefore, vicinal planes. Structures which closely resemble growth or etch pyramids from the third group would normally be bounded by perfect low-index crystallographic planes. In this case they are deformed. The angles between the bounding planes and the (111) surface are generally larger than 10 deg. The fine ridges are present, even on the smoothest surfaces, as shown in Fig. 1. They are along a (110) direction. The height differences could not be resolved with interferometric techniques. The basic characteristic structures of the second group are depressions and hillocks. These are bounded by three planes, two of them with larger slopes than the third one. The edges between the planes, as projected to the (111) surface, point in (211) directions. Various habits of these structures are shown

Jan 1, 1964

By A. M. Rowe

A considerable quantity of experimental hydrocarbon K-factor data has been correlated as a function of component identity, temperature, pressure and convergence pressure. To utilize these correlations effectively, convergence pressure must be determined accurately, particularly for volatile mixtures near their critical states. This paper presents phase diagrams that illustrate physically the meaning of convergence pressure. A new method, referred to hereafter as the "critical composition method", will be outlined for calculating convergence pressure. An example calculation has been included to illustrate how to use this new technique. INTRODUCTION The principle of hydrocarbon phase composition calculations as applied to such diverse problems as optimizing separator performance or predicting fluid compositions at various stages of reservoir depletion is the same. Usually, temperature, pressure and the numbers of moles of the various components of the fluid contained in a given volume are known. Questions answered by the phase calculation are what fraction of the total mass of fluid exists in each of the equilibrium phases, and what are the mole fractions of the various components in the two phases? To answer these questions the Natural Gasoline Supplymen&apos;s Assoc. (NGSMA) has correlated a considerable quantity of K-factor data as a function of temperature, pressure, component identity and convergence pressure.l To use these correlations to obtain the best answers possible, one must be able to calculate the convergence pressure. This is particularly true for over-all fluid compositions in the neighborhood of the critical state. STATEMENT OF THEORY Use of convergence pressure as a correlating parameter is based on a postulate similar to the law of corresponding states used in correlating PVT data of hydrocarbon gases. This postulate, which proposes convergence pressure as a correlating parameter, has been stated as follows: "The equilibrium vaporization constant for one component in a complex system is the same as the equilibrium constant at the same temperature and pressure for the same number or kind of components, providing only that the convergence pressures of the two systems are exactly the same at the same temperature and that the components are of the same homologous series".2 This law, as with all laws of physics, cannot be proven theoretically. It can only be justified by experimental data supporting its premises. Arguments have been made that this law violates Gibb&apos;s phase rule. For example, consider a four-component system. By Gibb&apos;s phase rule, which is thermodynamically rigorous, f = c — P + 2 =4, for a four-component, two-phase system. Thus, four independent intensive variables must be specified to establish completely all the intensive variables of the equilibrium phases. On the other hand, according to convergence pressure theory, only three variables need be specified for any mixture containing four different components. These variables are temperature, pressure and convergence pressure. Thus, the two laws appear to be in conflict. However, the convergence pressure postulate is more restrictive than Gibb&apos;s phase rule. It applies only to mixtures of the same homologous series. Hence, these two concepts are not in disagreement. PHASE DIAGRAMS DESCRIBING CONVERGENCE PRESSURE This paper presents phase diagrams grading from the simple two-component system to the more complex four-component system to illustrate convergence pressure. A less abstract definition of convergence pressure will be stated that is

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By E. C. Harder, D. F. Hewitt

Since early in 1916, when it became apparent that the steel industry of the United States could not depend for the duration of the war on several important foreign sources of manganese and might have to depend entirely on domestic ores, the U. S. Geological Survey, with the assistance of several cooperating organizations, has made a comprehensive investigation of domestic manganese resources. The work has included field studies in a number of states well as annual, quarterly, and monthly canvasses among operators concerning current and future production. In order that the interested public might have access to the important results of the studies, preliminary reports concerning the field work as well as periodic summaries of production were issued as promptly as possible. Although numerous summaries of production l2, l3, l4 have been prepared from time to time for the use of the several boards and committees responsible for the conduct of the war, it has been thought for some months that those engaged in the industry, as well as others, might be interested in a preliminary summary of the accumulated geologic and production data. The cessation of hostilities, in November, 1918, probably detracts from the usefulness of much of the material that is here presented, but apart from the historic interest in the performance of an important industry in war time, there is a possibility that some of the conclusions may be helpful to those who continue to exploit domestic deposits, as well as to those who wish to measure the country&apos;s independence in mineral supplies. Appropriate final geologic reports are being prepared by the geologists who did the field work. The present authors, having done but a small part of the recent field work, acknowledge with great appreciation the use of preliminary and unpublished reports and the cordial informal cooperation of the following geologists in the preparation of this paper: F. L. Ransome, G. W. Stose, F. C. Schrader, J. T. Pardee, E. L. Jones, Jr., H. D. Miser, Laurence LaForge, J. B. Umpleby, Arthur Keith, F. J. Katz, and E. S. Larsen, of the U. S. Geological Survey. Field work in Virginia was carried out in cooperation with the Virginia Geological Survey, T. L. Watson, State Geologist; in Georgia, with the Georgia

Jan 1, 1920

By K. Torssell, U. Lindborg

The kinetics of precipitation deoxidation is considered from a theoretical point of view. The size distribution and the total content of deoxidation products are estimated statistically as a function of time, taking into account Stokes and gradient collisions between the particles and separation at the top surface of the bath. The assumption is made that two particles coalesce into one larger particle as a result of a collision. General expressions are derived and calculations are carried out numerically for the case of silica particles in liquid iron. The analysis predicts a three-stage behavior for the removal of oxygen, an incubation stage, a stage of rapid separation, and a slow final stage where the content approaches the equilibrium value. The agreement with experimentally determined size distributions and deoxidation times is considered to be good. A quantitative estimation of such growth mechanisms as diffusion from the melt and redistribution of oxygen from small particles to large ones shows that these latter mechanisms cannot explain the experimentally observed gvowth of inclusions. This also indicates that collisions provide the important growth mechanism. OXIDE inclusions precipitate when a deoxidizer like silicon or aluminum is added to a steel bath. The inclusions grow and the large particles tend to separate from the bath. For each type of oxide the growth determines the sizes of the final inclusions as well as the total inclusion content of the steel. The mechanism of growth is controversial, however. It has been suggested that an inclusion grows principally by diffusion of atoms through the melt to the inclusion particle or principally by collisions and coalescence with other inclusions. Diffusion growth is always present to some extent but recent experiments and calculations by Torssell,&apos; Kniippel et &apos;a1.,2 Sano et al. and Miya-shita4 indicate that collisions may be more important than previously realized. A detailed analysis has so far been lacking. The present paper is a quantitative, statistical analysis of the growth and separation of inclusions and is based on a collision theory. Nuclea-tion is not considered. The numerical estimates are based on the experimental conditions of Torssell&apos;s&apos; investigation and comparisons are made with his observations. Torssell&apos; studied the growth and separation of silica particles in liquid iron. Samples were taken from a 0.6 kg iron bath at various times after the addition of silicon. By a particle-counting technique developed by Bergh and Lindber~the size distribution of the inclu- sions was determined. The number of particles at the first sampling, 10 sec after silicon addition, was of the order of 3 x lo7 to 10&apos; per cu cm, the largest particles having a radius of 2 to 4 pm. The volume fraction was 0.001 to 0.004; i.e., the dispersion was very dilute. During subsequent holding the largest particles increased their radius by a factor of 10 after about a minute, and the whole size distribution was displaced toward larger values. These results were obtained with allowance for precipitation of the equilibrium concentration of oxygen during solidification. The bath contained less than 0.01 pct of C. Figs. 1 and 2 show the typical appearance of the inclusions. Most particles are very closely spherical and appear to have been liquid or semiliquid in the melt. The observed number of inclusions, about 5x 10&apos; per cu cm, is of the same order of magnitude as found by ~er~h.&apos; This is a large value. It follows that the diffusion distances are very short and that the precipitation

Jan 1, 1969

By David W. Brunton

Mine-drainage and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, existing conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Jan 1, 1913

By M. R. Stauffer, Z. Hajnal

Seismic velocity determinations over Precambrian outcrops near Flin Flon, Manitoba, indicate that several different rock types have sufficient velocity contrast to make reflection mapping possible. Stratigraphic and fault contacts between metasedimentary and metavolcanic rocks have been mapped at some depth. A mu1ti-fold reflection survey attempted to trace the depth extension of an ore-bearing (Pb-Zn) rhyolite horizon within the metavolcanic rocks. A synthetic seismogram has been produced from a 10,000-ft sonic log and provides means of comparing seismic records with the local geology. From this the optimum frequency spectrum and the maximum resolution of the seismic signals were estimated.

Jan 1, 1978

By H. H. Einstein

Swelling ground is one of the most feared problems in tunneling. Although usually not causing sudden failures during construction, the very large and longlasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners up to 1 m (3 ft) thickness that have been cracked or crushed, tunnel inverts that are heaving at 0.1 m (0.3 ft) per week during construction and continue to heave during decades. This paper summarizes essential components of design construction procedures where tunnels in swelling rock can be built to perform satisfactorily. It is important to point out that design and construction cannot and should not be separated. The way the tunnel will be built has to be an integral part of the design. Swelling can be defined as time dependent volume increase and is distinguished from squeezing, another time dependent phenomenon occurring in tunneling. Squeezing involves exceeding the shearing resistance while swelling usually does not. Swelling of rock masses can occur as swelling of the intact rock, swelling of wall rock, of gouge and of filler in the discontinuities of a rock mass, and as a combination of the above. Swelling mechanisms have been discussed elsewhere (ISRM 1983).

Jan 1, 1984

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,&apos;J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,&apos;J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Reginald E. Hore

I. INTRODUCTION. SINCE the discovery of silver at Cobalt, Ontario, in 1903 more than 100,000,000 oz. of silver have been produced b: the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the next five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of about $26,000,000. For 1910 the production was 30,558,825 oz. valued at $15,436,894, and yielding a profit of about $9,000&apos;,000 The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, are given in Table I. TABLE I.-Silver-Production of the Cobalt District, 1904 to 1909 SMELTING-ORE. Production. Value. Silver-Content. Value Per Ton Ounces. Oz. Per Ton. 1904 206,875 $111,887 1,309 $708 1905.:.... 2,451,356 1,360,503 1,143 634 1906 5,401,766 3,667,551 1,013 687 1907 10,023,311 6,155,391 677 416 1908 18,022,480 8,468,293 736 363 1909 22,436,355 10,809,872 809 389 CONCENTRATES. 1908 1,415,395 $665,085 1,240 585 1909 3,461,470 1,651,704 1,174 559 The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-or( is largely high grade, averaging about 3,000 oz. per ton- A

May 1, 1911

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,&apos;. &apos; Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980