Search Documents

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma-type iron formation constitute low-grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 m thick occurring separately or with other iron formation facies are associated with cherts, carbonates, shales, turbidites, tuffs, and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher-grade deposits derived by secondary enrichment processes.

Jan 1, 1983

By Charles Maier

IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936

By C. A. Czako

INTRODUCTION In recent decades sintering and pelletizing of finely divided materials have become the primary tonnage producing modes of agglomeration. This statement is especially true in the iron and steel industry and, to a lesser degree, in the nonferrous, chemical and non-metallic minerals processing industries. In every industry the main objectives in agglomerating fines are essentially the same, namely to convert ores, minerals and chemicals of undesirable fineness into agglomerates characterized by a size consistency desirable for subsequent use or processing. Depending on the type of agglomeration process selected and the conditions maintained during agglomeration, the physical process of increasing size is complemented by a number of other unit processes. These processes can occur simultaneously, consecutively or in an overlapping manner. Some of these additional unit processes are incidental to the agglomeration operation, but at the same time can be critical, depending upon the subsequent use of the product. Accordingly, during processing, conditions have to be controlled to either suppress or enhance the extent of completion of these unit processes. The purpose of this report is to review laboratory testing as the basis for engineering modern sintering and pelletizing plants. Considering that most typical applications are for the iron and steel industry, agglomeration of ferrous materials is reviewed and discussed. When these total processes are adapted to suit non- ferrous materials, chemicals, or non-metallic substances, the over- all approach remains the same; only the processing parameters are affected as necessitated by the different nature of the materials.

Jan 1, 1977

By H. S. Munroe

To those familiar with ore-dressing practice, it is hardly necessary to dwell upon the importance of the jig. Within its proper sphere no substitute has been found that does the work as well or as cheaply. Its capacity is large, it requires but little attention, and the losses are small. In one form or another, it is the principal machine used in the concentration of low-grade ores, and for the separation of one metallic mineral from another; and it is almost the only machine used for the purification of coal. The present paper is a study of the action of the jig in the light of results obtained in the Lake Superior copper mills, ad at the St. Joseph Lead Co.'s dressing-works, in Missouri; and a description of experiments undertaken with the view of reproducing and isolating the conditions of jigging, in order to develop the laws which underlie the process. There are two recognized systems of jigging, the English and the Continental or German. The English system is a development of the hand-jigging formerly employed in Cornwall and other metalliferous districts of England, and introduced by English miners to this country. In this method the crushed ore, coarse and fine together, is first jigged oh a

Jan 1, 1889

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

By James P. Dr. Kimball

SULPHUR is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are laborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and quantitative disparities are scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By J. S. Aronofsky

The results of polentiometric model studies and numerical computations are described. The purpose of these studies was to determine the influence of the mobility ratio on flooding efficiencies during water encroachment in petroleum reservoirs, in systems of regular well geometry. The direct line drive well pattern having relative spacing distances of one and one-half to one was investigated for water to oil mobility ratios of 10. 1. and 0.1. The results of these studies indicate that the pattern Sweep efficiency i.; very dependent upon the mobility ratio. INTRODUCTION The almost universal occurrence of water in the immediate neighborhood of oil-hearing sands lends considerable emphasis to the desirability of having a rational analysis of water encroachment into petroleum reservoirs. This problem has 1)become increasingly important with the accelerated use of water injection for secondary recovery operations. The water encroachment problem has been studied from both the theoretical and experimental viewpoints by Muskat.' He has formulated, in a precise manner, differential equations to express flow in a water encroachment system, and rigorous analytical solutions have been developed for the linear, radial, and spherical cases.' However, it becomes exceedingly difficult to solve the encroachment problem rigorously for any general two-dimensional system in which the shape of the two-fluid interface is not immediately evident from the geometry of the system. The difficulty lies in the fart that a rigorous analytical solution requires that the shape of the two-fluid interface be known simultaneously with its instantaneous posititon and with the pressure distribution on both sides of the interface. Although this paper concerns the study of the two-fluid system of oil and water. the methods described in the paper are generally applicable to other systems of incompressible and immiscible fluids in which the displacing fluid sweep-the displaced fluid down to a residual value. In each region it is assumed there is only one mobile fluid and its mobility is constant throughout the region. The Same procedure. with minor alteration, is applicable for gas injection systems provided the assumption can be made that both the displaced and displacing gases can be described by steady state formulas. For the particular two-fluid problem considered in this paper, there is a relative permeability. K, and a viscosity. p. associated with the water zone, and a different permeability and viscosity associated with the oil zone. The K/p (mobility value associated with a particular volume element of the porous medium. at any instant of time. will depend upon whether the element is ahead of. or behind the advancing interface. It is assumed that all volume elements ahead of the interface are characterized by the K/p value for oil, while all the elements behind the interface are characterized by the K/p value for water. That is. the K/p value in the oil zone is constant throughout the oil zone. and the K/p value in the water zone is also constant but different from the value in the oil zone. The symbols are defined at the end of the paper. The well pattern chosen for initial study is the direct line drive; the swept-out area at breakthrough was determined by two different methods which are described in the section on theory. These are: 1. Potentiometric analyzer 2. Numerical computation The use of the potentiometric analyzer for studying water flooding problems is adequately described in the literature, particularly for cases where the mobility in the water zone is assumed equal to the mobility in the oil zone." ' 5

Jan 1, 1952

By A. E. Lehman

A RECENT demand for some form of panoramic display of an important railway line, showing its branches, connections, and terri tory controlled by it, revealed to the writer the advantages of' a topographical model or relief map fix this purpose. Hitherto, maps of this nature have been used chiefly for scientific and geographical purposes, and confined to a comparatively narrow field of service. They deserve to become more popular and to have their advantages better understood. Much has been written and accomplished in this direction by Prof. Lesley, Messrs. Harden, Moulten, de Mendonca Cortez, and others; but I believe their pub lished descriptions of the methods employed in the construction of these models are confined to those used by themselves. It is the writer's aim to present in condensed form these various methods, and some suggestions of practical value as to the most economical course of procedure, as well as to mention some of the uses that may be made of the results obtained Methods of Construction.—Many different materials have been prepared and used in the preparation of relief maps, such as metal, clay, plaster, gypsum, wax, putty, Card-board, papier-mache, wood, and compositions of varions kinds, with results more or less success ful : wood, however, in the writer's experience, has been found to be by far the most satisfactory, combining the advantages of stability, accuracy and ease of handling. The following is a brief description of several of the methods used in constructing topographical models : When clay, wax, putty, compositions or materials of a plastic nature are used, the operator carries his work up from its base by means of measurements or by the eye, manipulating and shaping the material as best he can, ac cording to such features of his subject as he wishes to delineate. This process requires remarkable skill, and given this, will probably fall short even then of an approximation to accuracy; lacking essential elements of detail nil over the work and exactness, particularly in position and elevation of the most important points in the territory mapped. When either of the above mentioned materials or compositions are used, metal or wooden pins are sometimes driven into the base or level datum plane of wood, the top of these pins giving the eleva-

Jan 1, 1886

By George H. C. Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable apparatus, which can rapidly give a sufficiently reliable indication of the relative dust hazard. HISTORY OF DUST DETERMINATION IN ONTARIO The first record of mine-dust determination in Ontario is given in an article by Dr. J. H. Elliott,' in which he records a few dust counts made with the Palmer spray apparatus. There were insufficient data from which to draw any definite conclusions or reasonably compare with present-day counts using the konimeter. The first konimeter dust sampling was started in the Porcupine district in 1926, using light-field counting without adhesive and with no sample treatment before counting. A method of semidark-field counting was used from about 1928 to 1931 and dark-field illumination was adopted permanently about December 1931. The konimeter has been continued as the principal means of dust sampling in the mines of Ontario, where South African practice has been adopted because in South Africa most careful study has been given the problem of silicosis, and very complete records of work done there are

Jan 1, 1937

By Edmund Kirby

THE results to come from the application of cheap oxygen to industry in general will be so great that it is not possible to enumerate them beforehand and still less to estimate them. We naturally think first of the fuel to be saved; yet this is only a minor item. The main results will be changes in methods of manufacture or of operation. The speed of operation will be greatly increased, with consequent savings in labor and fixed charges, and also, in most cases, in the cost of fuel. High temperature will be brought within the reach of every manufacturer, whereas it is now available only to those operating expensive electric furnaces located within reach of large water power. New speeds and new temperatures mean improvements and processes not thought of at present. Incidentally the changes in methods will probably change the location of important world industries, the tendency being to concentrate at the fuel centers. The whole subject is so new that most of the data which an engineer requires for definite estimates do not exist. All that is possible now is to obtain a general view of the subject with rough and fragmentary estimates for some of the industries with which we are specially concerned. Most of the figures presented deal with fuel saving merely because there are available no data from which to estimate the effect on speed of operation. When working out the practical problems involved in substituting oxygen for air, in most cases the change will be made step by step; by trying out air enriched with increasing percentages of oxygen. Such partial applications of oxygen will be temporary expedients during the transition and there will be no stopping place short of the complete substitution of air by oxygen. This final stage is therefore the one discussed in this paper.1

Jan 11, 1924

By Earl Oliver

Page A.I.M.E. Stabilization Committee Activity................. 133 Definition of Capture Rule: Robert E. Hardwicke.......................... 134 Westmoreland Natural Gas Co. vs. DeWitt................ 135 Kelly vs. Ohio Oil Co......................... 135 Bernard vs. Monongahela Gas Co.................... 136 Definition of Ownership in Place..................... 137 Prospective Stabilization Remedies.................... 137 Dean Roscoe Pound's Four Teats of Practicability.............. 137 I. Mechanically Feasible....................... 138 Capture Rule.......................... 138 Ownership in Place....................... 140 Mechanical Separatio.7 Method................. 140 Engineering Appraisal Method................. 141 II. Economically Advisable...................... 143 Capture Rule.......................... 144 Ownership in Place....................... 144 III. Politically Wise.......................... 144 Capture Rule..........................144 Ownership in Place.......................147 IV. Legally Sound..........................148 Capture Rule..........................148 Ownership in Place.......................149 Dean Henry M. Bates' Analysis......................149 Raumé................................152 The A.I.M.E. Stabilization Committee was named in 1932 to ascertain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from E. DeGolyer under date of Jan. 25. 1935. in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937

By F. M. Yans, A. D. Donaldson, A. R. Kaufmann

Beryllium was mixed by powder. metallurgical techniques with copper, nickel, iron, and chromium, respectively, to form beryllium -rich binary alloys which Mere then extyuded and rolled transtverse to the extrusion direction. The effect of each alloying element was determined by tensile testing. In solid solution, small amounts of iron and nickel had an embrittling effect, while copper in solution increased the strength but had no effect on ductility. The effect of chromium was complicated and not readily explainable. Observations concerning the planes and modes of fracture were made. BERYLLIUM possesses some very attractive properties for general design applications, especially its strength to weight ratio which is approximately twice that of aluminum and three times that of stainless steel. Equally significant, however, is its combination of high moduli , high strength (approximately 70,000 psi tension and 40,000 psi shear), and low density (0.0658 Ib per in.3), which has made it a potentially important structural material for use in high-speed aircraft and missiles. The main attractions of beryllium are most marked when compared to other constructional alloys now in use. For example, while its density is approximateiy that of magnesium, its modulus of elasticity is approximately seven times that of magnesium, three times that of titanium, four times that of aluminum, and 1 1/3 times that of steel. Furthermore, its relatively high strength and high melting temperature permit design for service temperatures to about 1100°F. It is felt by the aircraft industry in general,' that the high cost of beryllium can easily be amortized by the savings in fuel costs, and increases in aircraft payload and range. The only factor which has prevented the use of the metal in structural applications is its lack of sufficient ductility. It is this property that has retarded the development and utilization of beryllium. Beryllium's modes of deformation, Fig. 1 indicate that the main fracture planes at room temperature in a randomly oriented sample are the (0001) basal planes; the (1150) prism planes are the planes of secondary fracture.' Klein, Macres, Woodard, and Greenspan3 obtained elongations of up to 40 pct in beryllium sheet rolled above 700°C when the (0001) basal planes were oriented parallel to the plane of the sheet (see Fig. 2).

Jan 1, 1962

By Oliver Bowles

Dimension stone is a term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, contrasted with crushed, broken and pulverized stone covered in another chapter. Dimension stone includes cut stone, rough building stone, ashlar,* rubble, monumental stone, paving blocks, curbing, flagging, and many types of ornaments and novelties carved from stone. Riprap-large, irregular blocks used for shore protection-is classed with crushed and broken stone. Composition, Varieties, and Properties Dimension stones are of many kinds. The principal varieties are granites, trap rock (diabase, basalt, and gabbro), sandstone, limestone, and marble. Slate is covered in a separate chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. The basaltic rocks are darker in color than the granites. They contain little or no quartz and consist largely of plagioclase feldspar, augite, pyroxene, and hornblende. They are classed commercially as black granites. Limestone consists essentially of calcium carbonate. Dolomites and magnesian limestones used as dimension stone are classed with the high-calcium limestones. Marble is a crystalline form of limestone, but in the trade, any carbonate rock which will take a polish is called a marble. Many limestones which are fossiliferous but which will take a polish are sold as a decorative stone for lobbies of hotels and office buildings. Sandstone consists essentially of silica in the form of sand grains cemented into a coherent mass. Although rock occurrences are numerous and widespread, the exacting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced joints or planes of weakness can be used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive colors or color pattern, and freedom from impurities that may cause stains or deterioration usually are demanded. Hardness is a variable property. Granites and diabases are as hard as or harder than steel, while limestones and marbles may be scratched with a knife. The hardness of sandstone depends upon the degree of cohesion of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except where stones are subjected to abrasion as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains. Stones are of many colors and thus can satisfy a variety of tastes. For monumental stone, a marked contrast between polished and tooled surfaces is preferred in order that inscriptions may be read easily. Strength requirements usually may be disregarded because any sound structural stone suitable in other respects is almost invariably many times as strong as would be required for any ordinary use. The pressure on the base course of the Washington Monument, Washington, D. C., is less than 700 psi, and highgrade granites, limestones, sandstones, and marbles will sustain a crushing load of 10,000 to 25,000 psi. A structure made of stone with a crushing strength of 15,000 psi would have to be nearly 21h miles high before crushing of the lower courses would occur. However, stone disintegrates more readily under severe

Jan 1, 1960

OFFICERS OF THE WOMAN'S AUXILIARY AIME President-Mrs Robert D Coombs, 375 Paramus Road, Paramus, N J First Vice-President-Mrs W McG Peirce, Troy Court 73 F, New England Avenue, Sum¬mit, N J Second Vice-President-Mrs Andrew E Beer, Richardson Avenue, Sea Cliff, Long Island, N Y Third Vice-President-Mrs Ira T Hook, 494 Norton Parkway, New Haven, Conn Fourth Vice-President-Mrs John R Kenney, 427 W Wrightwood Avenue, Chicago 14, Ill Fifth Vice-President-Mrs Alfonso Ballon, Montero Rosas 115, Barranco, Lima, Peru Recording Secretary-Mrs Arnold H Miller, 601 West 115th St, New York 25, N Y Assistant Recording Secretary-Mrs R J Mechin, 66 East 79th Street, New York 21, N Y Corresponding Secretary-Mrs Theodore Nagel, 76 Remsen St, Brooklyn 1, N Y Treasurer-Mrs Robert W Rowen, 116 East 68th St, New York 21, N Y Assistant Treasurer-Mrs Samuel H Dolbear, 11 Broadway, New York 4, N Y Assistant Treasurer-Mrs H A Kursell, 12 Murray Hill Road, Scarsdale, N Y

Jan 1, 1956

By S. Le Fevre

THE application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration: The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to 4 or s in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same-current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills.

Jan 6, 1914

By E. N. Pugh, J. V. Craig

WhILE it has been established that well-defined microhardness impressions can be produced in germanium by room-temperature indentation,1-3 the role of dislocations in the process is the subject of continuing discussion.4-7 Recently, Carroll and ~anaka'

Jan 1, 1969

By Jean Howard

RECENT attempts to produce secondary recrystalli-zation in high-purity iron have given conflicting results. Coulomb and Lacombe1'2 did not find it but Dunn and Walter3,4 did. The latter workers have stated that (100) [001] and/or (110) [001] orientations develop depending on the oxygen content of the annealing atmosphere. This Technical Note records results which are in agreement with Dunn and Walter in so far as it shows that secondary recrystallization can be produced in high-purity iron, but does not confirm that both types of orientation are obtainable. Similar observations have been made on chromium-iron and molybdenum-iron, although when this technique is used on 3 1/4 pct Si-Fe, both types are obtained as in the work of Dunn and alter.' Pure iron strip was cold-rolled from sintered compacts prepared from Carbonyl Iron Powder-Grade MCP of the International Nickel Co. (Mond) Ltd. The powder contains about 0.5 pct 0, 0.01 pct C, 0.004 pct N, (0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni—that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The iron powder was (a) pressed at 25 tons per sq in. into blocks measuring 3 by 1 by 0.3 in., (b) deoxidized in hydrogen (dewpoint -60°C) by heating first at 350°C and then at 600° C until the dewpoint returned to -60°C at each temperature and (c) sintered in hydrogen (dewpoint -40°C) at 1350°C for 24 hr. (when dewpoint is referred to in this Note, it is the value as measured on the exit side of the furnace). The sintered compacts were cold-rolled to 1/8 in., annealed in hydrogen (dewpoint -60°C) at 1050°C for 12 hr and cold-rolled to 0.004, 0.002, and 0.001 in. with inter-anneals at 900°C for 5 hr and a final reduction of 50 pct. Final annealing of strip between alumina or silica plates at 875" to 900°C in hydrogen with dewpoints of -20°, -55" and -80°C produced secondary grains with the (100) in the rolling plane; the extent of secondary recrystallization was greatest when the dewpoint was -55°C. Annealing in a vacuum of 2 x 10"5 mm Hg at the same temperature produced no secondary recrystallization at all. With strip thicker than 0.002 in. very few secondary crystals developed whatever the conditions of annealing. Using a processing schedule somewhat similar to that described above, secondary recrystallization was produced in two bcc alloys of iron, viz. 80 pct Fe + 20 pct Cr and 96 pct Fe + 4 pct Mo. The former was reduced to final thicknesses of 0.001 to 0.004 in. and the latter to final thicknesses of 0.001 to 0.016 in. With the chromium-iron, a final anneal at 1250°C (found to be the most effective temperature for developing secondary crystals in the 0.004-in material) with a dewpoint of -25°C produced a greater degree of secondary recrystallization than with dewpoints of -50°C or -20°C. Secondary crystals developed in strips of all thicknesses from 0.001 to 0.004 in. Final annealing in vacuum produced no secondary crystals at all. For the molybdenum-iron a temperature of 1200°C was most effective. It was found that a dewpoint of -50°C during the final anneal gave better results than a dewpoint of -25 "C on the 0.008 in. material. Final annealing in vacuum gave slightly worse results than annealing in hydrogen with a dew-point of -50°C. Secondary crystals were developed in strips of all thicknesses up to 0.008 in. The experiments show that the extent of secondary recrystallization is a maximum for certain critical values of oxygen content of furnace atmosphere and annealing temperature, and that these values are different for different alloys. The thinner the material, the less critical these values are. The general conclusions are that secondary recrystallization can be obtained in high-purity iron, chromium-iron, and molybdenum-iron, using a processing schedule similar to that which will cause the phenomenon to take place in high purity 3 1/4 pct Si-Fe. Unlike the silicon-iron, however, only the (100) (0011-- orientation has been produced in these alloys, irrespective of the temperature of final annealing and the oxygen content of the furnace atmosphere. The information used in this Note is published by permission of the Engineer-in-Chief of the British Post Office.

Jan 1, 1962

By Philip B. Bucky

[ ]

Jan 1, 1942

By W. A. Ver Wiebe, E. G. Dahlgren

The year 1937 must be considered the most eventful one ever experienced in the development of oil and gas activity. Out of a total of 57 new pools discovered, 18 are apportioned to eastern Kansas and 39 to western Kansas. (For statistical purposes Kansas is divided along the meridian that separates ranges 3 E. and 4 E.) In addition to numerous longdistance extensions of the large Hugoton gas field of southwestern Kansas, two other gas pools were discovered in the area lying west of range 3 E. The 37 new oil pools in that area are to be found in 13 different counties, among which Rice heads the list with a total of seven oil pools and one gas pool. Ellis and Barton Counties both added six new oil pools, while Russell County follows in fourth place with four. Among eastern counties Butler heads the list with four new pools. Cowley arid Chautauqua each accounted for three new discoveries. The number of wells necessary to accomplish this result totals 2657, of which 1915 are oil wells and 128 gas wells. The initial production of the oil wells amounted to 2½ million barrels. Although most of the wells were drilled in proven territory, there was a good deal of wildcatting. The fact that 614 dry holes were completed emphasizes the ever-present risk attendant upon the efforts of pioneers. Some of the more venturesome spirits reached out to the counties farthest west in the state. An indication of the feverish excitement reached at times is recorded in the fact that no less than 600 drilling operations were in progress during one week in May, or the fact that over 100 new locations were staked during the second week in July. During one week in May, 65 successful oil wells were completed for an initial production of 68,000 barrels. Many drilling obligations came due during the year, and this perhaps accounts for the fact that one company had as many as 59 active operations at one time during September. Another evidence of great interest in oil possibilities in Kansas is furnished by the record of sales of oil properties, which in one case reached the high figure of about $3000 per acre.

Jan 1, 1938

The total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numerous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a, depth of 2332 m. (7650 ft.) before abandonment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin. Producing companies are: De Bataafsche Petroleum Maatschappij (Royal Dutch-Shell combine in Dutch territory); The Anglo-Saxon Petroleum Co. Ltd. (Royal Dutch-Shell combine in British territory); De Nederlandsch-Indische Aardolie Maatschappij (De Bataafsche Petroleum Maatschappij-Dutch East Indian Government combine); De Nederlandsche Koloniale Petroleum Maatschappij (Standard Oil Co. of

Jan 1, 1933