Search Documents

By D. J. McAdam

In a series of papers the author and associates have discussed the influence of temperature on the tensile properties of metals.11-18 These papers present much information about the influence of temperature and the stress system on the conventional indices of mechanical properties, with special attention to the fracture stress. A recent study of the data, however, has revealed much additional information about the influence of temperature on the fundamental factors involved in the flow of metals. The present paper presents results of this study. Attention will be confined almost entirely to results derived from tension tests of unnotched cylindrical specimens at strain rates a little slower than those used in ordinary tension tests. According to a concept first presented by Ludwik and elaborated in recent papers by others,8,9,22,23 the mechanical state of a metal depends on the total plastic strain, but not on the temperature during straining, provided that the only structural changes are those essential to plastic deformation. In the summer of 1948, however, the author made the previously mentioned study of results of a general investigation by the author and associates and reached the conclusion that the mechanical state depends not only on the total strain, but also on the temperature during the straining. A number of diagrams were then prepared. These conclusions were presented without diagrams in a discussion last October of a paper by Dorn, Goldberg and Tietz.2 The metals used in the investigation on which this paper is based were Monel and oxygen-free copper. The Monel was supplied by the International Nickel Co. through the courtesy of Dr. W. A. Mudge. The copper was supplied by the Scomet Engineering Co. through the courtesy of Dr. Sidney Rolle. The data to be presented are based on results of tests at temperatures ranging between 165 and — 188°C. Description of the apparatus and methods of test are given in previous papers.1011'1"2 The present paper is the first part of the general discussion of the influence to temperature on the stress-strain-energy relationship for metals. The next paper will deal with metals that are subject to structural changes other than those induced solely by plastic deformation. Influence of Temperature and Plastic Strain on the Flow Stress of Monel and Copper For a study of the influence of temperature on the stress-strain relationship, flow-stress curves obtained with annealed metals at various temperatures will be compared with curves obtained with the same metals after cold drawing or cold rolling at room temperature. Diagrams thus obtained with Monel and copper are shown in Fig 1 to 8. Fig 1 to 7 show the variation of the flow stress with temperature and plastic strain; Fig 8 is a diagram of a different type, derived from Fig 4 to 7. In Fig 1 to 7 strain is expressed in terms of A0/A, in which A0, and A represent the initial and current areas of cross-section. Since values of Ao/A are represented on a logarithmic scale, abscissas are proportional to true strains; moreover, the true strains representing prior plastic deformation and those representing subsequent strain during a tension test are directly additive. Fig 1 shows flow-stress curves obtained with annealed Monel. Five of the curves are based on results of tension tests. Between yield and the maximum load, the flow was under longitudinal tensile stress; between the maximum load and fracture, the local contraction induced transverse radial tensile stress. The portions of curves designated F, therefore, represent flow with increasing radial stress ratio, the ratio of the transverse stress S3 to the longitudinal stress Si. Curve Fo is based on the ultimate stresses of specimens taken from bars that had been cold drawn various amounts.17 Since the tensile stress at the maximum load is unidirectional, curve Fo represents the course that a flow-stress curve would take if the stress during an entire tension test could be kept unidirectional. The flow-stress curve F obtained at room temperature (Fig 1) has been established accurately by numerous measurements of the diameter of the specimen during the extension from yield to fracture.17 At the time of the experiments, however, no apparatus was available for measuring the diameter during tension tests at low temperatures. Nevertheless, curves have been established to represent with sufficient accuracy the flow at low temperatures. Each flow-stress curve must be tangent to a curve U, which starts at a point representing the ultimate stress of annealed metal. Since the ultimate stress is based on the area of

Jan 1, 1950

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota's Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns' (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By Pual M. Tyler

BLIZKRIEG tactics in the present war have consumed metals on such a profligate scale that some of the best-laid procurement plans for civilian and military needs of even a year ago seem in retrospect incredibly meager. Conservation of raw materials has reached an all-time climax in Germany, where metals are worth more than human life and throwing away an empty toothpaste tube may be legally punished by death. Even the United States and the British Empire, proud masters of nine tenths of the world?s known mineral reserves and processing plants, are being driven to metals and feverishly expanding production facilities that not long ago were deemed overbuilt. After the war is over and inevitable postwar readjustments are completed, it is reasonable to expect that purchasing power ? or at least the ability to procure the comforts and luxuries of life ? will be distributed among vastly larger population than ever before, accelerating the rising trend in demand for industrial raw materials in ever greater quantity and variety.

Jan 1, 1942

By M. A. Torcaso, P. Raimondi

To study mass transport in systems simulating oil recovery processes, different porous media were saturated with a mobile (carrier phase) and a stationary phase. Slugs of carrier phase containing a small amount of solute were displaced with pure carrier phase. By analogy to the chromato-graphic processes, the velocity of the solute can be predicted from a knowledge of the partition coefficient and the saturation provided that equilibrium between the two phases exists. Equilibrium was found to exist for different porous media, solutes and rates. The conditions were varied over the range normally encountered in the laboratory and in the field. The longitudinal dispersion of a solute undergoing interphase mass transfer was also investigated. INTRODUCTION The production of hydrocarbons by gas cycling, enriched gas drive and C02 or alcohol displacement involves, among other factors, relative motion between two phases and compounds, hereafter called solute, which are soluble in both phases. The solute is carried forward by the faster flowing phase at a lower velocity than the average velocity of that phase. Retardation of the solute is caused by chromatographic absorption and desorption in the slower flowing phase and by the degree of departure from equilibrium. At equilibrium the concentration of solute in the two phases can be related by the equation* CSw = K Cso ,............(1) where C, and C are the concentration of solute in the aqueous and oleic phases respectively and K is the equilibrium ratio, or partition coefficient. Displacement theories must contain an explicit assumption with regard to equilibrium, i.e., whether the compositions can be related by Eq. 1. The existance of equilibrium depends, in general, on the relative velocity between the phases. Unfortunately, other factors such as gravity segregation and viscous fingering, also depend on velocity. For this reason, whenever effects of rate on displacement were observed,2-4 it was practically impossible to discern what caused them — lack of equilibrium or the factors mentioned above. Equilibrium between phases has been the subject of extensive studies in fields such as extraction or chroma to graphy. It has received only small attention in flow through the type of porous media encountered in oil production.5 For this reason a method was developed which makes it possible to study the movement of a solute as it is affected by rate, type of porous media, partition coefficient and carrier phase, but in the absence of segregation or fingering. The information obtained enables one to determine when the assumption of equilibrium can be made. Briefly, the method consists of (1) saturating the core with a mobile and an immobile phase, (2) injecting a slug made up of the same fluid as the mobile phase and a small concentration of mutually soluble solute, (3) measuring the lag and the peak height of the slug at arrival and (4) correlating these variables with fluid properties such as partition coefficient and mixing constants of the medium. PROPOSED MECHANISM The principles of chromatography are combined with the equation of longitudinal mixing to predict the velocity of a solute slug compared to the bulk velocity and the peak height of a slug.6-9 The equation so obtained is valid under equilibrium conditions only. Therefore, a comparison between experimental and predicted results will give a measure of departure from equilibrium. This work was done with either the oleic or the aqueous phase being immobile. For simplicity, the following development is based on the case where the oleic phase is immobile. However, the treatment is the same in either case.

Jan 1, 1966

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has had a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1790. Practically all of this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the "white man" Indians are known to have made salt from such salt springs as those that existed at Avery Island, La., Charleston, W.Va., Saltville, Va., and Onondaga, N.Y. In 1862 the first rock salt was mined in the U.S. from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, Va., and then at Retsof, N.Y., in 1885. Of the more than 40 million tons produced annually in the United States, about 68% or 27 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc.

Jan 1, 1975

By J. J. Jakosky

All electrical geophysical methods depend for their operation upon the effects produced by the flow of an electric current. By studying these effects it is possible to predict the general axis of current flow. The greater flow of current is in the path of greatest effective conductivity; and since the effective conductivity of a mineralized zone is different from that of its surrounding envelope (usually much greater), it is possible to locate such a mineralized zone by the distribution of current. Due consideration must be given, of course, to geological structure, to type of mineralization, and to other factors. A number of methods are used to cause this flow of current, and various methods arc available for detecting the presence of such current flow and for studying its effects. In a rather detailed way, this paper will discuss the theoretical and practical phases of the inductive methods of geophysical prospecting. Electromagnetic Generation of an Electeomotive Force The inductive method is so named because the current flowing in the conductor is obtained by electromagnetic induction, instead of by the use of ground electrodes through which a current is passed as in the applied potential systems, or by direct contact with the orebody. An alternating current flowing in a coil will create an electromagnetic field around the coil. This field will have the same frequency as the current and will radiate or travel outward from the coil in closed magnetic or flux circuits. These flux circuits (in air or a homogeneous medium) will be perpendicular to the plane of the coil and will extend or travel outward with uniform velocity in every direction. Maximum feld exists in the plane of the coil. Such a coil used for transmitting or as the "energizer" will exhibit similar figure-eight characteristics to those exhibited by the direction-finding coil which will be described in detail later.

Jan 1, 1929

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

Z. W. Bartlett, J. C. Carrington, H. C. Petersen and K. T. Price were elected vice-presidents of the Freeport Sulphur Co. Blandford C. Burgess was transferred on January 1 to the new Defense Materials Procurement Agency as strategic materials specialist. In May the Region III headquarters of this organization was moved to London. L. C. Campbell was elected president of National Coal Assn. Mr. Campbell, who has been a member of the National's Board of Directors and Executive Committee for many years, is vice-president of the Coal Div. of the Eastern Gas & Fuel Associates and in charge of their extensive mining operations in West Virginia, Pennsylvania and Kentucky. Vern H. Christoph has been transferred to Panama Canal Co., Marine Bureau, Navigation Division, Port Captains Office, as an admeasurer at Cristobal, Canal Zone. Eugene Cline, recently graduated from the University of Kentucky, has been employed by Pond Creek Pocahontas Coal Co., at Evanston, Ky. Sanford S. Cole, assistant manager of research at the Titanium div. of National Lead Co., received the Alumni Citation from his alma mater, Alfred University, Alfred, N. Y. This was in recognition of outstanding achievements and services in the field of ceramics which have brought honor to the institution. U. K. Custred, recently graduated from University of Kentucky, and may be reached now at Box 87, Monterey, Tenn. Robert E. Dwyer, executive vice-president of Anaconda since 1940, was recently elected president of this company and its subsidiaries, Chile Copper Co., Chile Exploration Co., and Andes Copper Mining Co. As president, Mr. Dwyer succeeds the late William H. Hoover who died in Butte, Mont.

Jan 1, 1952

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By H. L. Shergold, O. Mellgren

Concentration of fine quartz particles at the iso-octane/water interface has been investigated under different conditions of pH and dodecylamine concentration. The results obtained from the related studies on the effect of amine concentration and pH on the interfacial tension, adsorption density, electrokinetic potential, contact angle, and concentration of the various amine species in the system are presented. A good correlation was obtained between these different variables. It is well-known that very fine mineral particles are difficult to float in conventional flotation machines. Flotation rate studies have revealed that the rate of flotation of fine mineral particles is much smaller than that of coarser size fractions. The theories accounting for this behavior have been discussed by Arbiter and Harris1 and also Meloy.2 Theoretically, a hydrophobic fine particle might never make contact with a bubble because of the presence of an energy barrier in the vicinity of the air/water interface.' This energy barrier will have electrostatic, hydrodynamic, and Van der Waals force components. It was thought that by using an oil phase instead of air the energy barrier would be decreased so that fine particles could be concentrated at the oil/water interface more readily than at the air/water interface. The technique used involves dispersing the fine particles in water, containing the appropriate chemical reagents, and injecting a fine dispersion of iso-octane oil droplets into the pulp. After vigorous conditioning, the pulp is passed into a separating column where the oil droplets coated with a layer of mineral particles rise to the surface to form a separate layer. Air is introduced into the base of the separating column to ensure that heavy agglomerates of oil and particles report with the organic layer. This technique has been described previously4 and adopted by Lai and Fuerstenau5 who studied the alumina-dodecyl sulfonate system. The interfacial phenomena in the system composed of hematite, water, and iso-octane in the presence of sodium dodecyl sulfate have been studied and the results reported" earlier. This paper describes the results obtained from investigations into the interfacial phenomena in the quartz/water/iso-octane system in the presence of dodecylamine. The technique used in measuring the interfacial tension, electrokinetic potential, contact angle, and adsorption density were similar to those described previously? Materials Selected pieces of a high purity natural quartz, from the Isle of Man, were crushed in a laboratory jaw crusher and pulverizer. The — 52+72 mesh size fraction was retained and leached with successive washes of hot concentrated hydrochloric acid to remove iron impurities. When no iron was detected in the solution by ammonium thiocyanate, the quartz was washed thoroughly with distilled water until the conductivity of the wash water assumed that of the distilled water. Samples of 25 g of the —52+72 mesh quartz were ground for 5.25 min in an agate vibratory mill. The ground product was 100% —44 m and 57% —10 am, as determined by the Andreasen pipette. The specific surface area of the sample used for the adsorption and flotation tests was 0.94 sq m g-l. This corresponds to a mean particle diameter of 2.4 am. The —44 am quartz sample was stored under vacuum in the presence of silica gel crystals. For the contact angle determination between the three phases, quartz, iso-octane, and water, a piece of the natural quartz was ground into a block about 15 mm long, 15 mm wide, and 5 mm thick. One surface of the block was then polished by successively finer grades of silicon carbide "paper." The final polishing was conducted with alumina on a "hyprocel" paper. The polished quartz specimen was cleaned using nitric acid and ethyl alcohol followed by a wash with distilled water and then stored under distilled water. This pro-

Jan 1, 1971

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

By William E. Ford, Edward Salisbury Dana

I. Oxides of Silicon. 11. Oxides of the Semi-Metals : Tellurium, Arsenic, Antimony, Bismuth ; also Molybdenum, Tungsten. III. Oxides of the Metals. The Fifth Class, that of the OXIDES, is subdivided into three sections, according to the positive element present. The oxides of the non-metal silicon are placed by themselves, but it will be noted that the compounds of the related element titanium are included with those of the metals proper. This last is made necessary by the fact that in one of its forms TiOz is isomorphous with MnOp and PbOz. A series of oxygen compounds which are properly to be viewed as salts, e.g., the species of the Spinel Group and a few others, are for convenience also included in this class.

Jan 1, 1922

By C. R. Van Hise

PART I.-GENERAL PRINCIPLES. [ ]

Jan 1, 1902

By I. R. Kramer, L. J. Demer

T. H. Alden and R. L. Fleischer (General Electric Research Laboratory)— The authors' results indicate clearly and, we believe, significantly that during tensile deformation the surface layers of an aluminum crystal are hardened more severely than the interior of the crystal. A probable explanation of this effect, as the authors indicate, is that dislocations in the primary slip system may be obstructed at the surface or, it should be added, near the surface. The intent of this discussion is to show that the oxide film on aluminum is not likely to be responsible for this effect, but that the results can be understood if it is assumed the secondary slip is more active in the surface layers than in the interior. Prior study has shown that the principal mechanical effect of an oxide film on a single crystal is to raise the yield stress while leaving the rate of strain hardening during the initial deformation relatively unaffected.33 Since the yield stress is unchanged during polishing in the present case, we conclude that continual removal of the oxide film exerts a small effect on the plastic hardening.* It appears that the hardening interactions are occurring not only at the immediate surface, but to an appreciable depth below it, although with decreasing severity. For example, Kramer and Demer found that with removal of 0.004 in. from a specimen, the easy glide region was extended somewhat; but the yield stress did not decrease. The initial yield stress was recovered only after 0.041 in. was removed. Since a very brief polish would permit dislocations trapped behind a surface film to run out,34 extra dislocations must, instead, be trapped to a considerable depth below the surface. The same conclusion is drawn from the observation of decreasing hardening slope with increasing surface removal rates. If the hardening interactions were only at the immediate surface, a full softening effect would be observed at some small removal rate. The view is taken here that strain hardening is principally caused by small amounts of secondary slip.35 The secondary dislocations will interact in various ways with the primaries, interfering with their motion and causing them to accumulate in the crystal. Prior studies of easy glide have shown Diehl's model of hardening to be qualitatively consistent with the effects of impurities,36 of temperature,36 and of crystal size.37 On this basis the enhanced hardening of the surface layers in aluminum arises from increased secondary slip at and to some depth below the surface. Selective removal of this hardened layer is expected to decrease the measurable "bulk" hardening, the effect increasing with the removal rate and decreasing with the applied strain rate. We suggest that the stress on secondary systems is raised by the bending moments arising from interactions with the grips during the deformation. This stress from the grips has been shown to be a maximum37 near the surface, and hence, increased secondary slip should result. Prior investigations of grip effect:; indicate that as the grip stresses are raised by changing the crystal shape, the easy glide slope increases while the extent of easy glide decreases.38-40 It has been shown also that bending moments superimposed during tensile testing may either decrease easy glide, when supporting the moments caused by gripping, or increase it, when cancelling the gripping moments.38 This interpretation of the authors' results, emphasizing the special importance of secondary slip near the surface, is also consistent with the earlier results of Rosi.41 Copper crystals alloyed with silver in the surface layer show greatly increased easy glide compared with pure copper. In addition, the easy glide slope is reduced. The effect of bulk alloying in extending easy glide has been well established and has been interpreted as indicating the relative difficulty of secondary slip in alloy crystals. Since non-basal glide is difficult in zinc crystals, the effects of surface removal during deformation may be less important. Experiments to test this idea are in progress. I. R. Kramer and L. J. Demer (authors' reply)—The authors wish to thank Dr. Alden and Dr. Fleischer for their discussion. Our interpretation of the data in the paper is that dislocation motion is obstructed by "debris" which starts to form at the surface and extends towards the interior of the crystal with further plastic deformation. The fact that we did not find a reversion from Stage II to Stage I by surface removal shows that in Stage II the "debris" fills the entire cross-section of the specimen. Drs. Alden and Fleischer take the view that bending stresses due to the grips are responsible for the

Jan 1, 1962

By F. R. Hensel

THE absorption of oxygen by molten metals is a quick and convincing method to determine the metallurgical characteristics of various types of furnaces.1 The investigation was restricted to the use of coreless induction furnaces. A major variable in induction furnace practice is the frequency and its influence was studied by comparing melts made in a 5000-cycle and a 60-cycle induction furnace respectively.2 The authors are not aware that such a comparative study has been made before and therefore present this paper in the belief that the results will be of general interest. ANALYTICAL METHODS FOR DETERMINATION OF OXYGEN IN NICKEL An analytical procedure for determining NiO by a quick and simple, laboratory method has been worked out in collaboration with Dr. Herty, of the Pittsburgh Station of the Bureau of Mines. It was found that Dr. Herty's aluminum method as used for the. determination of FeO in iron and steel was very suitable for use with nickel if instead of hydrochloric acid a 10 per cent solution of nitric acid is used for bringing the metal into solution. Essentially this method involves deoxidizing the nickel-oxygen alloy with aluminum (2Al + 3NiO = Al203 + 3Ni) and determining the resulting Al203 by a residue analysis. The original oxygen content can then be calculated from the amount of Al-20,. The method as suggested by Dr. Herty3 is referred to in the present paper as method B. A slight modification of method Bled to the application of method A, a description of which is given below according to F. W. Beiter?:3

Jan 1, 1932

By J. E. Drury, W. M. Byers, E. J. Lynch

Measurements made with starch ~~~~s indicate that the Presence of starch serves to depress the streaming potential of a clay mud system. Measurements with pure starch slurries show that the addition of NaCl or CaO reduces the streaming potential significantly. The addition of NaOH, however, causes only a minor reduction in potential even when there are large changes in mud resistivity. INTRODUCTION In their excellent study of the streaming potential, Hill and Anderson' proposed that the presence of conductive solids within the filter medium will reduce the generated potential. This theory was demonstrated with measurements on shaly sandstone cores having various "b" factors; the cores with the higher negative b factors showed markedly lower potentials. (The factor b was originally defined by Hill and Milburn2 in an expression relating the resistivity of a shaly sandstone to the resistivity of the interstitial water: log F, = log F,, + b (log 100R,)'. 'he factor b, therefore, is a measure of the contribution of the conductive solids to the total conductivity of the sample. It has been found experimentally to be directly related to the amount of chemically exchangeable ion per unit pore volume.) In the logical extension of this hypothesis to the streaming potential created by filtration through mud cakes, they suggested that the presence of nonconductive starch in a drilling mud would have the opposite effect; i.e., it would cause the streaming POtential to be increased. The high streaming potentials that they observed with lime muds were attributed to this cause. A cross-plot of some of their results which are relevant to this discussion is given in Fig. 1. The lime-mud curves and untreated-mud curve are taken from curves given in their paper. The gyp-mud line was estimated from their statement that the measured streaming potential for gyp muds in the range of 1.5 to 2.0 ohm-m was approximately 18 mv/1,000 psi. These gyp-mud potentials were the lowest that they reported for any of the bentonitic-clay muds, and were the only ones which were less than the untreated-mud potentials. This very low streaming potential of gyp muds has also been observed in field studies.' By way of comparison, a U. of Texas publication4 gives the approxi-ate compositions for lime and gyp muds shown in Table 1. These materials are added to a bentonitic-clay mud base. It can be seen that both of these muds contain significant amounts of calcium salts and that the gyp mud has the higher concentration of starch. It would appear from this and from the data shown in Fig. 1 that starch may well be the cause of a streaming-potential reduction, rather than a potential increase. EXPERIMENTAL A series of streaming-potential experiments has been performed using a cell of a design similar to that reported by Wyllie.5 Calomel electrodes were used in both the mud slurry and the filtrate. Pressure in the cell was generated with high-pressure nitrogen. The primary objective of the investigation was to determine the effect of starch on the potential. Five different slurries were made which ranged in composition from untreated ben-tonitic mud (Baroid Aquagel) to a pure starch suspension (Baroid Im-permex). The intermediate slurries were prepared by mixing together a 9-lb/bbl clay mud with a 12-lb/bbl starch suspension in the ratios 1:3, 1:1 and 3:1. When starch was used alone, it was necessary to use an 18-Ib/bbl mixture, since leaner mixtures would not form a suitable filter cake. The clay mud used in the experiments was aged for three months before use. In addition to this series of measurements on the starch-clay mud mixtures, other experiments were performed to determine the effect on the potential of the absolute starch and Aquagel concentration, and the effect of adding various chemicals. RESULTS The effect of starch on the streaming potential is shown clcarly in Fig 2. Increasing percentages of starch resulted in n continually decreasing

By R. Simon, D. J. Graue

This paper presents correlations for predicting the solu-lility, swelling and viscosity behavior of CO2-crude oil sys8i.m~. The correlations were developed from experimental data obtained by the authors. These data are also presented. The data were determined by measuring the properties of mixtures of CO, and nine different oils. Experiinental conditions covered a range of 100 to 250°F and pressures up to 2,300 psia. Properties predicted by the correlations have average deviations, expressed as per cent of experimental value, of 2 per cent for solubility, 0.5 per cent for swelling and 12 per cent for viscosity. INTRODUCTION Interest in CO2 injection as an oil recovery process has led to the development of performance prediction methods which can be applied to specific reservoirs.1 iS To use these performance prediction methods, it is necessary to know the solubility, swelling and viscosity properties of CO2-crude oil mixtures at reservoir conditions. Some information on these properties has appeared in the literature; however, this information did not cover the range of different oils and conditions needed to prepare generalized correlations for reservoir engineering purposes. Consequently, an experimental program was undertaken to collect the data needed. The data obtained and the correlations developed from the data are described in the following sections of this paper. SOLUBILITY OF CO2 IN CRUDE OILS CO2 solubility data in the literature come from six principal sources. The solubility prediction method of Welker and Dunlop3 is limited to 80F. The information in Ref. 4 is of two types: the first includes binary and ternary mixtures of CO, and light hydrocarbons (C1 to C6), and the second gives data for CO1 and heavy hydrocarbons for a temperature range of 40 to 90F. Ref. 5 contains a KCO2 chart for systems whose convergence pressure is 4,000 psia. The KCO2's are based mainly on CO2-natural gas mixtures. Poettmann's work covered CO2 solubility in one condensate and one crude oil6,7 Ja-coby and Rzasa measured CO? solubilities as a function of pressure and temperature for two natural gas-absorber oil mixtures and two natural gas-crude oil mixtures.'8 CO, concentration in these four systems was fixed at 5 mol per cent. The work reported in this paper extends CO, solubility data to a variety of different crude oil types in a temperature range from 110 to 250F and pressures up to 2,300 psia. The experimental procedure used by the authors to obtain the solubility data consisted of combining known amounts of pure CO, and crude oil in a visual cell at a fixed temperature and measuring the bubble point of the mixture. Measurements were made for a total of 40 different CO2-oil mixtures and the results are shown in Table 2. The mixtures included nine different oils (seven crude oils and two refined oils) whose properties are listed in Table 1. All nine oils had vapor pressures less than 1 atm at the experimental temperatures. Consequently, analysis of the bubble-point vapor showed a CO, concentration over 99 mol per cent. At no time during these experiments was a second, more dense, liquid phase observed. The solubility correlation which was developed from the data in Table 2 is presented in Figs. 1, 2 and 3. In these figures, solubility is expressed as xco2 the mol fraction of CO, in the CO2-oil mixture. Fig. 1 shows solubility as a function of CO2 fugacity6 and temperature. Fig. 2 shows the same solubility data expressed as a function of saturation pressure and temperature. The solubility shown in Figs. 1 and 2 is for an oil whose UOP characterization factor is 11.7. UOP characterization factors of crude oils can be determined from Ref. 10 if the viscosity and APT gravity of the oil are known. Fig. 3 gives the solubility correction factor for oils whose UOP characterization factors differ from 11.7. The solubility correlation in Figs. 1, 2 and 3 predicted

Jan 1, 1966

By B. W. Gonser, C. M. Heath

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938