Search Documents

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

By Carl Pierce

The writer of this article has not attempted to write a technical paper; on the contrary, he has tried to express in "steel-plant English," for steel men, a viewpoint drawn from his practice and experience. It is not his thought that it shall be taken as the "last word" in the making of this class of steel, or that good rimming steel cannot be made by any other practice. The paper was written to serve as the basis of a discussion from which it is hoped much benefit may be derived. The paper deals only with rimming steel made by the open-hearth process, and with the lower carbon steels, such as sheet and tin bar, rivet stock, skelp, etc., although good rimming steel as high as 40 to 50 carbon can be made by having good open slags and giving proper attention to working and tapping temperatures. Definition of Rimmed Steel Rimmed steel is sometimes called open or effervescing steel to differentiate it from killed or partly killed steel. It is steel made by a process which permits the free escape of gases from the metal in the molds. In passing up through the metal, the gases keep it in a rolling action from the walls of the mold inward. The top of the ingot rims in as the metal chills and the walls of the ingot get thicker, the center part remaining fluid until it reaches a pasty condition when it is covered with a cast-iron cap. The Charge In making up a charge for rimming steel, clean stock of a known composition must be selected, special attention being given to the analysis of the materials. The silicon in good rimming steel must be eliminated to a trace, therefore it is advisable to have a uniform amount going into the charge. Too much silicon gives a raw melting heat from which rimming steel is unlikely to result. For this reason a charge containing not to exceed 40 per cent. pig iron and 60 per cent. scrap, with no iron ore, is preferred to the Monell type of charge in which as high as 65 to 70 per cent. pig iron is used with a proportional amount of iron ore for the removal of the excess silicon and carbon. The silicon content of pig iron varies so much from day to day in the average blast-furnace practice that there is danger of getting too much of this element in the latter mixture when

Jan 1, 1926

By Morris Cohen

Within the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;' and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, hc concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrernce of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. The general precipitation occurs at a

Jan 1, 1939

By Morris Cohen

Within the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;' and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, hc concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrernce of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. The general precipitation occurs at a

Jan 1, 1939

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

AS IS evident from the discussion in previous chapters, the methods by which an open-hearth heat may be made are numerous, but any heat, in the ingot form, may be classified as one of three types, depending upon the degree of deoxidation to which the metal is subjected. These are rimmed, semikilled, and killed, and desirable ingot structures, from the standpoint of distribution of porosity, are illustrated in Fig. 63. These are the most useful types of ingot structure [ ] and represent three stages in the continuous series from "wild" to "dead killed" (see Fig. 23, page 46) ; some of the variations of each type are discussed later in the chapter. The choice of ingot structure and of finishing practice used to produce the desired metal action in the molds is determined by consideration of: 1. Specified final analysis. As an example, the production of rimmed steels is mostly limited to carbon contents below 0.30 per cent and manganese contents below 0.60 per cent; on the other hand the production of low-carbon killed steel requires greater care.

Jan 1, 1944

By Ben. B. Cox

The principal events during the year consisted in the exploitation of the Kirkuk field, the regular operation of the four-million-ton pipe line to the Mediterranean, and the discovery of low-gravity oil on three other structures in the West Tigris (Shergat) area. The Iraq Petroleum Co., Ltd. continued the systematic exploitation and exploration of its Kirkuk field, maintaining a carefully unitized operation. Bottom-hole pressure differentials and low gas-oil ratios were maintained. All crude was produced by flowing The cleaning up following the construction of the Mediterranean pipe line, which began deliveries in August, 1934, was completed during the first quarter of 1935. The line easily maintained its rated capacity for the remainder of the year. The Mosul Oilfields, Ltd., through its operating subsidiary, the B.O.D., Ltd., expanded its exploratory organization from 9 to 16 drilling rigs and discovercd 20" A.P.I. crude on the Sadid, Hibbarah and Qasab anticlines. Whether these discoveries will be commercial pools remains to be proved. The Qaiyarah-Najmah-Jawan field, which was discovered by the I.P.C. in 1928, was extended arid production was found in the Eo-Cretaceous as well as the "Main Limestone" (Eocene, Oligocene and Lower Miocene). Gas caps were found under each of the crests of the West Tigris structures. Negotiations are in progress between the Mosul Oilfields, Ltd. and the Iraq Government for the extension of the Anatolian Railway from the Turkish border to Mosul, with a view to tanking the heavy West Tigris crude to the Mediterranean. The subsidiary of the Anglo-Iranian Oil Co., Ltd.', the Khanaqin Oil Co., Ltd., continued to operate its Naft Khaneh field near the Iranian (Persian) border to supply the local Iraq market through the Rafidain Oil Co., Ltd. Somewhat more than 28 million barrels of crude was produced in Iraq during 1935. Crude delivcred to the pipe line for export during the years 1934 and 1935 was: Year BaRrels 1934................................................. 7,096,669 1935................................................. 27,014,904 Total as at Dec. 31, 193.5.............................. 34,111,573 ° Converted at an avcrage of 7.0 bbl. per ton.

Jan 1, 1936

The principal events during the year consisted in the exploitation of the Kirkuk field, the regular operation of the four-million-ton pipe line to the Mediterranean, and the discovery of low-gravity oil on three other structures in the West Tigris (Shergat) area. The Iraq Petroleum Co., Ltd. continued the systematic exploitation and exploration of its Kirkuk field, maintaining a carefully unitized operation. Bottom-hole pressure differentials and low gas-oil ratios were maintained. All crude was produced by flowing The cleaning up following the construction of the Mediterranean pipe line, which began deliveries in August, 1934, was completed during the first quarter of 1935. The line easily maintained its rated capacity for the remainder of the year. The Mosul Oilfields, Ltd., through its operating subsidiary, the B.O.D., Ltd., expanded its exploratory organization from 9 to 16 drilling rigs and discovercd 20" A.P.I. crude on the Sadid, Hibbarah and Qasab anticlines. Whether these discoveries will be commercial pools remains to be proved. The Qaiyarah-Najmah-Jawan field, which was discovered by the I.P.C. in 1928, was extended arid production was found in the Eo-Cretaceous as well as the "Main Limestone" (Eocene, Oligocene and Lower Miocene). Gas caps were found under each of the crests of the West Tigris structures. Negotiations are in progress between the Mosul Oilfields, Ltd. and the Iraq Government for the extension of the Anatolian Railway from the Turkish border to Mosul, with a view to tanking the heavy West Tigris crude to the Mediterranean. The subsidiary of the Anglo-Iranian Oil Co., Ltd.', the Khanaqin Oil Co., Ltd., continued to operate its Naft Khaneh field near the Iranian (Persian) border to supply the local Iraq market through the Rafidain Oil Co., Ltd. Somewhat more than 28 million barrels of crude was produced in Iraq during 1935. Crude delivcred to the pipe line for export during the years 1934 and 1935 was: Year BaRrels 1934................................................. 7,096,669 1935................................................. 27,014,904 Total as at Dec. 31, 193.5.............................. 34,111,573 ° Converted at an avcrage of 7.0 bbl. per ton.

Jan 1, 1936

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;' and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot' formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. . The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. † The general precipitation occurs at a

Jan 1, 1938

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;1 and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. ? The general precipitation occurs at a

Jan 1, 1938

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 110 W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H20). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells[t] and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale[$] for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table I. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and I600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

William B. Cogswell, member of the Institute since 1872, died on June 7, 1921, at his home in New York City, after an illness of about six weeks occasioned by an infection of the middle car. Mr. Cogswell is survived by his wife, Mrs. Cora Brownell Cogswell; a son-in-law, and three grandchildren. His first wife died in 1877. William Cogswell was born at Oswego, Sept. 22, 1834, and was taken to Syracuse by his parents when he was four years old. He attended Hamilton Academy and private schools in Syracuse and Seneca Falls. In 1843, he visited England with his parents and brought back a set of drawing instruments, which led to a series of lessons in architecture under Luther Gifford, the only architect in Syracuse at the time. The boy drew many building plans and one set was used for the old Globe Hotel in Syracuse, erected in 1846 and 1847. In 1848, when only 14, he spent a year with a party that was surveying the route of the Syracuse & Oswego R. R. and relaying the tracks of the Utica & Syracuse R. R. He studied civil engineering at the Rensselaer Polytechnic Institute, Troy, for three years, but left that institution in 1852 without receiving his degree. Many years later, in 1884, the degree of C. E. was conferred upon him. During the three years following 1852, Mr. Cogswell served as an apprentice in machine shops at Lawrence, Mass., under the superintendence of John S. Hoadley. About 1856, he was made manager of the machinery department of the Marietta & Cincinnati R. R., at Chili-cothe, Ohio, and three years later became superintendent of the Broadway foundry at St. Louis, Mo. In 1860, in Syracuse, Mr. Cogswell was associated with William A. and A. Avery Sweet in the formation of Sweet Bros. & Co., which later became the Whitman & Barnes Mfg. Co. At the outbreak of the Civil War, Mr. Cogswell received a civilian appointment as mechanical engineer in the United States Navy. During 1860 he was located at Port Royal, S. C., having general supervision over the work of fitting up repair shops at five widely separated stations on the Atlantic seaboard and Gulf of Mexico. In this year his genius and resourcefulness were notably shown. He literally launched a naval machine shop, so that warships could be repaired without leaving, and thereby weakening, blockades against Southern ports. The machine shop was assembled by Mr. Cogswell and shipped by boat to Port Royal. There an old whaler was made over for machine shop purposes and Mr.

Jan 1, 1922

William B. Cogswell, member of the Institute since 1872, died on June 7, 1921, at his home in New York City, after an illness of about six weeks occasioned by an infection of the middle car. Mr. Cogswell is survived by his wife, Mrs. Cora Brownell Cogswell; a son-in-law, and three grandchildren. His first wife died in 1877. William Cogswell was born at Oswego, Sept. 22, 1834, and was taken to Syracuse by his parents when he was four years old. He attended Hamilton Academy and private schools in Syracuse and Seneca Falls. In 1843, he visited England with his parents and brought back a set of drawing instruments, which led to a series of lessons in architecture under Luther Gifford, the only architect in Syracuse at the time. The boy drew many building plans and one set was used for the old Globe Hotel in Syracuse, erected in 1846 and 1847. In 1848, when only 14, he spent a year with a party that was surveying the route of the Syracuse & Oswego R. R. and relaying the tracks of the Utica & Syracuse R. R. He studied civil engineering at the Rensselaer Polytechnic Institute, Troy, for three years, but left that institution in 1852 without receiving his degree. Many years later, in 1884, the degree of C. E. was conferred upon him. During the three years following 1852, Mr. Cogswell served as an apprentice in machine shops at Lawrence, Mass., under the superintendence of John S. Hoadley. About 1856, he was made manager of the machinery department of the Marietta & Cincinnati R. R., at Chili-cothe, Ohio, and three years later became superintendent of the Broadway foundry at St. Louis, Mo. In 1860, in Syracuse, Mr. Cogswell was associated with William A. and A. Avery Sweet in the formation of Sweet Bros. & Co., which later became the Whitman & Barnes Mfg. Co. At the outbreak of the Civil War, Mr. Cogswell received a civilian appointment as mechanical engineer in the United States Navy. During 1860 he was located at Port Royal, S. C., having general supervision over the work of fitting up repair shops at five widely separated stations on the Atlantic seaboard and Gulf of Mexico. In this year his genius and resourcefulness were notably shown. He literally launched a naval machine shop, so that warships could be repaired without leaving, and thereby weakening, blockades against Southern ports. The machine shop was assembled by Mr. Cogswell and shipped by boat to Port Royal. There an old whaler was made over for machine shop purposes and Mr.

Jan 1, 1922

By J. E. Owen

EXPERIMENTS on twenty-six drilling muds were carried out in an effort to establish a correlation between the apparent viscosity values for these muds as obtained with the Marsh funnel and the Stormer viscometer. This required a calibration of both instruments in which the density of the calibrating liquids was taken into account. Corresponding to the Marsh-funnel viscosity values that were obtained at 1500 c.c. in, 1 qt. out, equivalent Stormer viscosity values were obtained at a Stormer cylinder test speed of approximately 1100 r.p.m. Further, a linear relation between the logarithms of the Stormer cylinder test speed and the resulting apparent viscosity was found to exist for the muds tested for 200 to 1000 r.p.m. The significance of the slope of this linear relationship is discussed as it applies to the field use of drilling muds. It was concluded that Marsh-funnel viscosity measurements are expressible in absolute units that may be correlated with Stormer viscosity measurements, provided these are made in the manner described in the paper. INTRODUCTION The Marsh funnel is used almost universally to determine the viscosity of drilling muds in the field. The Stormer viscometer is commonly used to determine the viscosity of drilling muds in the laboratory. With the Marsh funnel, the time required for one quart of mud to flow out of the funnel originally filled with 1500 c.c. is often taken as the measurement of viscosity. With the Stormer instrument, drilling mud is tested at a cylinder speed of 600 r.p.m. and by means of calibration data the apparent viscosity is expressed in absolute units. Neither of these instruments is an absolute viscometer, and apparent viscosities obtained with either are influenced by the arbitrarily standardized conditions under which the measurements are made. It is disconcerting to the man in the field to be told that laboratory measurements of the viscosities of a group of muds differ widely, when he has already observed that they have identical viscosities when tested in the Marsh funnel. Drilling muds are not perfect fluids, therefore it is not surprising to find a lack of correlation between the apparent viscosity of a mud as determined with the Marsh funnel and that determined with the Stormer viscometer. The work described here was undertaken to develop a correlation between Marsh-funnel and Stormer viscosity measurements. To a considerable degree this has been accomplished. This study has resulted not only in a better understanding of the two viscosity instruments and the data obtainable from them, but has given considerable information regarding the viscosity characteristics of drilling muds. EXPERIMENTAL PROCEDURE Calibration of Harsh Funnel and Stormer Viscometer The first step in the experimental procedure was the calibration of the Marsh funnel and the Stormer viscometer with

Jan 1, 1941

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By Paul D. Foote

Most of the treatises on metallurgy intimate that simultaneously with the development by the atomic physicist of a really satisfactory theory of the atom will be inaugurated a new epoch in the science of metals. Metallurgically and metaphorically, we shall dwell in the Utopia of Sir Thomas More. It is my privilege this afternoon to demonstrate that this state has not arrived. An atom is a miniature planetary system consisting of a positively charged nuclear sun about which revolve electrons each carrying the negative charge e. The charge on the nucleus is + Ze where Z is the atomic number and the number of planetary electrons in a neutral atom is equal to Z. These electrons are arranged in several groups having different binding energies. Ordinary x-ray phenomena relate to processes occurring deep within the atom, usually with electrons in the so-called K or L shells. Such electrons in the heavier atoms are so closely bound to the nucleus that the forces exerted by neighboring atoms in a solid are relatively inappreciable. For most practical x-ray investigation, the atom may be considered as in the gaseous phase completely isolated from its neighbors. The K radiation from an element in the gaseous state, in the solid or liquid phase, or even in combination with other elements in all its possible valences, is almost identical.‡ Visual and ultraviolet spectroscopy is concerned with disturbances of the most loosely bound outer or valence electrons of the atom, always in the vapor state. The remarkable progress of the last year in both theo-

Jan 1, 1926

By Paul Foote

MOST of the treatises on metallurgy intimate that simultaneously with the development by the atomic physicist of a really satisfactory theory of the atom will be inaugurated a new epoch in the science of metals. Metallurgically and metaphorically, we shall dwell in the Utopia of Sir Thomas More. It is my privilege this afternoon to demonstrate that this state has not arrived. An atom is a miniature planetary system consisting of a positively charged nuclear sun about which revolve electrons each carrying the negative charge e. The charge on the nucleus is + Ze where Z is the atomic number and the number of planetary electrons in a neutral atom is equal to Z. These electrons are arranged in several groups having different binding energies. Ordinary x-ray phenomena relate to processes occurring deep within the atom, usually with electrons in the so-called K or L shells. Such electrons in the heavier atoms are so closely bound to the nucleus that the forces exerted by neighboring atoms in a solid are relatively inappreciable. For most practical x-ray investigation, the atom may, be considered as in the gaseous phase completely isolated from its neighbors. The K radiation from an element in the gaseous state, in the solid or liquid phase, or even in combination with other elements in all its possible valences, is almost identical. ? Visual and ultraviolet spectroscopy is concerned with disturbances of the most loosely, bound outer or valence electrons of the atom, always in the vapor state. The remarkable progress of the last year in both theo-

Jan 2, 1926

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 11o W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H2O). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table i. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By Earl C. Herkenhoff

Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95% of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978. "Separation of Bitumen from Dry Tar Sands," was the first blockbuster. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high &lids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95OC (203°F) in a 0.3 m solution of sodium carbonate-about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60.62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands.

Jan 1, 1983