Search Documents

By A. B. Cox, L. W. Wark

In an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solution composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents—namely, sodium cyanide—on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electrolytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60". There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1935

By AIME AIME

THE iron and steel activities of this meeting opened on Monday morning with the steel melting session," with G. B. Waterhouse in the chair and A. L. Feild as vice-chairman. N. A. Zeigler's paper, on "Gases Extracted From Iron Carbon Alloys by Vacuum Melbing," created considerable interest and the discussion in general was most favorable. H. W. Gillett and Louis Jordan of the Bureau questioned the method of analysis for oxygen and C. H. Herty, Jr., and J. M. Gaines, Jr., I , expressed their surprise at the large amount of oxygen with the high ,carbon alloys. Whether the gases found existed as gas in blowholes or as oxide inclusions was also a moot point. A paper by C. D. King, on "Basic Open-Hearth Yields," was an extremely interesting and valuable contribution. It was discussed by C. E.Kinney and A. L. Feild and numerous questions were asked throughout the presentation. Mr. King then presented a critical analysis of the losses together with novel methods of calculating them. A paper by C. H. Herty, Jr., and J. M. Gaines, Jr., on "Unreduced Oxides in Pig Iron and Their Elimination in the Basic Open-Hearth Furnace," followed. The question of silicates and oxides in pig iron created much discussion, notably by Henry Hanson and W. J. MacKenzie, who gave figures on chipping cost as a function of blast-furnace practice.

Jan 1, 1929

By James Kemp

PostScript to a paper presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 129 to 154. The writer looked over the quarry with care in the search for fossils, having in mind shells or corals of fairly large size. In the brilliant summer sunshine, none were observed on the glaring white ledges. The impression was gained that none were present and the statement to this effect was made in the edition of this paper published in the Bulletin' of the Institute for February, 1915, p. 136. On closer examination in the laboratory it has been discovered that the limestone itself is made up of minute organisms, which are clearly revealed by microscopic examination of thin sections. The principal component of the rock is a small foraminifer, 0.1 to 0.3 in. (2.5 to 7 mm.), of the genus Orbitoides, presumably an Oligocenic form. Figs. 1 and 2. illustrate it. The accompanying description has been kindly summarized by Marjorie O'Connell, M. A., Curator in Paleontology in Columbia University, who first detected the evidences of organisms in the rock. Orbitoides kempi O'CONNELL N. SP.1 The foraminiferan which makes up the Seboruco limestone is an Orbitoides of a Species new to North America. The only Orbitoides heretofore described from this country is 0. mantelli from the lower Oligocenic of the Gulf States. This form from Cuba, then, so different in all of its characteristics from the 0. mantelli, is of great interest as perhaps forming a basis of correlation over wide areas. The most closely related Species is 0. dispansa Sowerby, which occurs in the Nummulite limestone of the Eocenic of the Bavarian . Alps, in the Priabona beds of the lower Oligocenic of Massano, and elsewhere in Italy, as described by Gümbel.2 The age of the limestone in Cuba would thus Seem to be of upper Eocenic or lower Oligocenic age, probably the latter. The fossil has the form of a sphere Surrounded by a wavy rim of horizontal extent, the whole resembling two flat-brimmed, round-crowned hats placed base to base. The total extent of the Shell ranges up to 7+ mm., while the thickness of the central sphere is 2.5 mm. in one of the largest individuals. Like all of the other Species of Orbitoides, this form begins with a Single layer of chambers which multiply in one plane and assume a circular outline; but it is in the subsequent growth that the distinguishing specific characters appear, for the chambers at the central portion of the shell increase more rapidly than do those near the periphery and in consequence a Swelling is produced which finally gives the Spherical form which is so characteristic. The rim, on the other hand, shows little chamber-increase and remains thin. This is clearly Shown in the sections figured, where the central row of larger chambers forms the equatorial zone. Radiating from this row, in section, there appear, a number of solid cones alternating with broad reticulated ones. The solid cones mark the more dense structure forming the walls surrounding the reticulated or chambered cones. These appear upon the Surface as distinct pits, whereas the solid part appears as raised walls.

Jan 7, 1915

By John B. Baker, Bernard B. Betty, H. F. Moore

Fox several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.1,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. SPECIMENS The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.-The Bridgman method of casting single-crystal speci¬mens was used.3 The specimens were cast to the shape and size shown in Fig. I (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By Louis Huber

DESPITE the fact that centrifugal fans were first developed for ventilating mines and that artificial ventilation was first practiced in mines, the lack of knowledge of mining men on mine ventilation in general, and on fan performances and characteristics in particular, is very much in evidence today. While it is true that mines are much better ventilated now than they were 20 to 30 years ago, we have made very little progress in the study of mine ventilation, or in mine ventilating fan design. Today the average mine operator is woefully dependent on the engineers of mine fan manufacturers when he is in the market for a fan, and this situation works to the disadvantage of both the operator and the manufacturer. The former may be imposed upon by an unscrupulous sales engineer and induced to buy a fan which is not the proper one for the mine; when it is operating it may be wasteful of power and even accessory to a serious mine disaster. More often, however, it is the fan manufacturer who is imposed on. If the operator asks the manufacturer to build for him a fan that will deliver a certain quantity of air against a certain specified pressure and requiring a specified number of horse power when operating under these conditions, the manufacturer may build a fan that will comply with these specifications to the letter. When the fan is installed it is frequently found that it is delivering a greater quantity of air against a lesser pressure or a lesser quantity of air against a greater pressure, and is requiring more horse power than specified in the first case and less than that specified in the second. In either case the operator usually upbraids the manufacturer for not meeting specifications, and refuses to pay for the fan. The trouble in either case outlined above is that the pressure necessary to force the specified quantity of air through the mine has been estimated incorrectly by the operator or his engineers. When a fan is designed and built to deliver a certain quantity of air against a certain specified resistance it will operate at its maximum efficiency only when it is operating under

Jan 2, 1926

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By N. J. Grant, H. Brunner

This paber is concerned with the determination of equations relating elongation to the amount of shear taking place both along grain boundaries and in slip planes of poly crystalline aggregates during creep. Certain discrepancies with previously used equations are pointed out. Grain boundaries were observed to become serrated during creep, but it is shown that this does not necessarily prevent further grain boundary sliding. Direct obser-vations of subgrain boundary ingration lead to the conclusion that this migration facilitates sliding along serrated grain boundaries. It is bointed out that the state of stress at triple boints is still unknown. MOST of the mechanisms of deformation contributing to elongation are shear processes, such as slip, kinking, grain boundary sliding, and twinning. For quantitative investigations of individual deformation mechanism it is necessary to know the equation which permits the calculation of speci-tnen elongation from measured amounts of shear. This calculated elongation must then be compared with the observed total elongation. The authors' special interest concerned grain boundary sliding during creep. Although this subject has already been investigated quantitatively by McLean,' Rachinger,' and Fazan, Sherby, and Dorn, calculations indicated that none of the equations used thus far to relate shear with elongation were sufficiently well founded. A basic study of this relationship was thus made and the results of this study (which do not entirely agree with those previously used) are presented. Most of the ideas set forth apply not only to grain boundary sliding but to other mechanisms of shear as well. THE SPEAR-ELONGATION RELATIONSHIP Basic Models—The relationship between shear and elongation is trivial in the simplest case of shear, which is shown in Fig. l(a). The vector A; designates the displacement across the shear interface, and Au, and Aut are its components parallel and normal to the tensile direction, respectively. It is evident that the specimen elongation due to shear is equal to the longitudinal component of the shear vector, and it should be noted that the normal component does not contribute to the elongation of the specimen (there are, of course, two normal components in a three-dimensional model). The model shown in Fig. l(b) may be applied to mechanical twinning and to subgrain boundary tnigration. In this case the width (h) of an already existing shear band increases by the migration of an interface, but the shear angle y (angle of mis-orientation in the case of a subgrain boundary) remains constant. The geometrical relationships indicated in Fig. l(b) permit this case to be reduced to the one shown in Fig. l(a). For the resulting elongation A6 we find: where AV/V = fraction of the volume of the specimen swept by migrating interfaces , and 1 = length of specimen. Thus, assuming for example that the angle of mis-orientation is 1 deg, and that P = 45 deg, we find that the specimen elongates 0.87 pct of its length if the entire volume of the specimen is swept once by such a subgrain boundary. An example of deformation by migration of subgrain boundaries is shown in Fig. 2. The specimen shown was repolished after 9.8 pct creep strain and the test then continued for another \ pct. Since the shear vector has, in general, a component normal to the surface, subgrain boundary migration results in the formation of an inclined band delineating the region swept by the subgrain boundary. These inclined bands become clearly visible when observed with oblique illumina-

Jan 1, 1960

By J. J. Casey, R. S. Busk, D. L. Leman

The mechanical properties and the phase-temperature relationships of magnesium-lithium-aluminum, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys are presented. It is shown that the strengths of some of these alloys can be tripled by heat treating and aging but that the high strength is accompanied by brittleness and lack of stability. MAGNESIUM-LITHIUM alloys are interesting because the hexagonal structure of magnesium can be changed into the more ductile and workable body-centered cubic structure by the addition of only 10 pct lithium.1 After Loonam2 determined that the ductility of the magnesium-lithium alloys is destroyed by even trace quantities of sodium, it was possible to prepare ductile alioys and study their mechanical properties. Jackson3 and coworkers have ably described their results with both the binary and polynary magnesium-lithium alloys. The present paper is a report of the mechanical properties of wrought magnesium-lithium-aluminurn, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys. Experimental Procedure The alloys were made by melting 7 lb of magnesium in a steel crucible under a molten flux of 75 pct LiCl + 25 pct LiF3 previously dried at 1600°F. The metal was heated to 1300°F for alloying aluminum and zinc and then cooled to 1250°F for adding lithium (sodium content: 0.01 to 0.04 pct). After the lithium had been alloyed, dry LiF powder was sprinkled on the melt to thicken the excess flux. After a 15 min holding period, the flux was skimmed off. Paraffin vapors were used to protect the metal as it was poured into 3 in. diam by 11 in. long magnesium molds. Billets were extruded into 3/8-in. diam rod and 1/16 x 3/4-in. strip; sheet was prepared from 1/8x 7/8-in. extruded strip, first by hot rolling and then by cold rolling 2 pct per pass. Hot rollability, or the temperature range through which the alloys could be rolled, was determined by rolling the strip two passes at 30 pct reduction per pass. Cold rollability, or the percentage of cold reduction to cause detrimental cracking, was determined on 0.064-in. hot-rolled sheet. Standard ASTM procedures were followed to obtain the mechanical properties, using 0.2 pct offset for the yield strengths. The level of properties produced with commercial magnesium alloys using the procedure described is given in a previous publication." Results Magnesium - Lithium - Aluminum System: The good workability of magnesium-lithium alloys is illustrated by the data in table I, which shows approximately how the extrusion pressure decreases as the amount of cubic phase increases. Binary magnesium-lithium alloys are soft and weak, but aluminum raises their strengths con-

Jan 1, 1951

By B. H. Caudle, M. D. Witte

In predicting the performance of a pattern injection operation, the engineer needs to know both the amount of oil to be recovered and the rate at which the recovcry will take place. This paper- describes fluid flow model studies on the effect of mobility ratio on the rate of oil recovery in a five-spot. The results show the change in fluid conductivity (total flow rate/pressure drop) as the sweep-ont pattern increases for mobility ratios between 0.1 (and 10. There data, when cornbitted with a knowledge of reservoir permeabilities and sweep-orit pattern efficiencies, cata he used to predict the cLrmulntivr oil production as a function of time for homogeneous five-spot injection systems. INTRODUCTION The flow potential in a pattern flood element is a function of the mobility ratio and how far the injected flood front has gone.1,2 For a waterflood project having a mobility ratio of one, the conductance—which is the flow rate per unit pressure drop (q/Ap)—-will remain the same throughout the life of the flood. If the mobility ratio is favorable ( < I), the conductance of the project will drop continuously throughout the operation. If, on the other hand, the mobility ratio is unfavorahlc. the conductance ratio will increase continuously. Therefore, if the reservoir engineer wishes to predict either the rate at a specified pressure or the pressure at some rate for a secondary recovery project, he must know how the conductance will vary during the flood. Other investigators have studied this problem using potentiometric models&apos; or analytical solution&apos;. The

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant&apos; on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,&apos; aging took place during the creep tests. &apos;In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500&apos; or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500&apos; or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40&apos; to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.&apos; At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By Lawrence H. Van Vlack, Otta K. Riegger

Periclase-type oxides were examined microscopically after being exposed to siliceous liquids. The rate of grain growth was found to be inversely proportional to the grain diameter. Grain growth proceeds more rapidly at higher temperatures, but is retarded by increasing liquid contents. aMag-nesiowiistites with higher MgO contents grow less rapidly than those with higher FeO contents. The growth rate is reduced by the presence of a second solid phase. The silica-containing liquid penetrates as a film between the individual magnesiowus tite grains. This is independent of time, temperature, amount of liquid, or the MgO/ Fe0 ratio. When present, olivine and spinel-type phases can provide a solid-to-solid &apos;&apos;bridge" between magnesioustite grains. THIS paper presents the results of a study of the microstructures of periclase type oxides in the presence of a silicate liquid. The purpose was to learn more about the effect of service factors such as 1) time, 2) temperature, and 3) liquid content upon A) grain growth, and B) liquid location among the solid grains. This study was prompted by the fact that periclase refractories are known to have very little solid-to-solid contact when the phases which are present are limited to periclase and liquid. Such a micro-structure gains industrial significance because it permits fracture during service when stresses are applied at high temperatures. The details of ceramic microstructures have not received extensive attention. This is in contrast to the extensive attention given to a) the phase relationships pertaining to refractory compositions, and b) the details of the microstructures of comparable metallic materials. A brief review will be made of the pertinent phase relationships and microstructural considerations in general, as well as of refractory compositions. a) Phase Relationships. This investigation was limited to those compositions in which (Mg, Fe)O was the solid phase. MgO and FeO form a complete series of solid solutions. Pure MgO has the name of periclase. The related FeO structure is called wustite. Both have the NaC1-type structure: however, wustite possesses a cation deficiency so that the true composition is Fe<10 even in the presence of metallic iron. The phase relationships involving solid (Mg, Fe)O and a silicate liquid are shown in Fig. 1. In this case. the liquid is saturated with (Mg, Fe)o. There-fore its SiOz content is below that encountered in orthosilicate liquids. As a consequence the liquid phase specie:; are primarily the following ions: and 0-&apos; plus occasional Fe+ ions. Two features are of importance: a) the liquid contains relatively small species and b) the liquid contains large quantities of the same species as the solid. viz., Fig. 2 shows the system, FeO-SiOz, which will be used in some of the discussions that follow. This diagram is the right side, vertical section of Fig. 1. Here, as pre\iously, the composition at the FeO end of the diagram is nonstoichiometric, varying from Feo.950 when the liquid oxide is in contact with the solid iron, to about Fe 0, when the solid oxide is in equilibrium with an atmosphere of equal proportions of CO and C02 at the solidus temperature. The Fe/O ratio will be maintained in wustite in the presence of SiO,. However, the FeM/Fe++ ratio in the liquid will be lower because of the effect OIF the SiO, on the activity of the FeO. With the addition of MgO to wustite, the over-all composition (IvZg, Fe)@, has a value of x lying between 0.9 and 1.0 when the COz/CO ratio is 1.0&apos;. b) Microstructures. In general, published attention to refractory microstructures has been directed toward the phase analyses that accompany compositional variations. This is illustrated by Harvey6 in his work on silica brick and by wells7 in his work on periclase brick. In each case, a series of altered zones is encountered which provides a sequence of phase associations. If due consideration is given to reaction kinetics, such an examination reveals phases that are compatible with equilibrium studies. Admittedly, however, it is often necessary to determine more complicated polycomponent systems to account for all the phases present.8 Relatively little attention has been given to microstructural geometry in ceramic materials. Certainly less attention has been given to this aspect of ceramic microstructures than to the size, shape, and distribution of the constituent phases in metals. Burke has pointed out that the grain size of oxides follows the same growth rules as for metals, viz.,

Jan 1, 1962

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company&apos;s operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years&apos; supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By AIME AIME

As already announced, the XCIIId meeting of the Institute will be held at Toronto, beginning July 23, 1907. Hotel Headquarters will be at the King Edward Hotel, in which also the sessions will be held. The Queens, Rossin, Wallen, Iroquois and Palmer are good hotels not far from the King Edward. Members must secure their hotel-accommodations beforehand, by direct correspondence with the hotel they select. For those who neglect this precaution, the Local Committee will doubtless do what it can, but is unable to promise anything. Correspondence concerning this meeting (including notices of intention to attend it) should be addressed hereafter exclusively to Mr. W. G. Miller, Provincial Geologist, Bureau of Mines, Toronto, who is the representative of the Local Committee. The excursion to Cobalt, Lake Tenagami, Sudbury, etc., arranged by that Committee, involves the use of a special Pullman train for meals and lodging. After waiting a reasonable time to hear from members, the Local Committee has made its contract for Pullman cars. According to its latest report, there was still room for additional excursionists. Under this head, application made immediately to Mr. Miller may not be too late. Sessions for the presentation of papers, etc., will be held at the King Edward Hotel on Tuesday afternoon, July 23, and Wednesday morning and afternoon, July 24. The following papers have been accepted: 1. Sonic Reflections on Secrecy in the Arts, by James Douglas, New York, N. Y. .2. The Wilfley Table, by R. H. Richards, Boston, Mass. 3. The Tar-Sands of the Athabaska District, by&apos; Robert Bell, Ottawa, Can. 4. The Occurrence of Nickel in Virginia, by Thomas L. Watson, Blacksburg, Va. 5. Coal-Briquetting in the United States, by E. W. Parker, Washington, D. C.

Jul 1, 1907

By William Hutton Blauvelt

An official of one of the prominent iron companies of the South recently made the following statement during a discussion of the present conditions of the Southern iron business: " The trouble with us in the South has been that we have been satisfied to buy iron and coal lands, build blast-furnaces, and make pig-iron. We stopped at pig-iron, and as a result we are all poor. The South needs diversified industries, and needs to work up its raw products into articles the Southern market can use. If we had realized this sooner, some of us might now be rich." The South is awakening to this view, and in the Birmingham district alone one basic steel-mill is already in operation, and in a year&apos;s time another and much larger one will be turning out rails and shapes, with rod- and wire-mills in prospect. It is to chronicle another metallurgical step forward in the same district that I have prepared the following description of the new by-product retort coke-oven plant recently put in opera-

Jan 1, 1899

By Paul Gordon

The distribution coefficient, k, of interest in zone refining is generally defined as the ratio of the solid to the liquid solubilities of one element in another at the normal melting point of the solvent. In practice, distribution coefficients are frequently calculated from solubilities at temperatures well below the melting point of the solvent, e.g., at a eutectic temperature. This is done because of the general lack of accurate data on the liquidus and solidus curves in most phase diagrams. The practice is equivalent to assuming that the liquidus and solidus curves are straight lines in the temperature range between the melting point of the solvent and the temperature at which data for the solubilities are known. It is recognized that the k values so derived may be in serious error; we have found evidence in recent zone-refining operations that a case in point is silicon in aluminum. The phase diagram found in the literature for silicon in aluminum indicates a eutectic on the aluminum-rich side at 12.5 at. pct Si and at 577°C,1 and a solid solubility of silicon in aluminum at this temperature of 1.59 pct.2 It also shows the liquidus and solidus as nearly straight lines from 577°C to the melting point of aluminum (660°C)1,2 The k value obtained from this data is 0.13. This is almost exactly the same as the k value (about 0.14)&apos; obtained in a similar way for copper in aluminum. Yet we have found by mass-spectrograph analyses* of three bars of zone-refined aluminum that copper is efficiently removed from aluminum by zone refining but silicon is not. Two of the three bars of aluminum were zone-refined in our laboratories, the other in the laboratories of AIAG Metals, Inc. The former two bars, designated bars PG2 and PG3, were 30 in. long by 1 in. in diameter during refining; each was processed in a high-purity graphite boat* and kept under refining stage of the process consisted of thirty unidirectional zone traverses at rates of about 1 to 2 in. per hr, with a zone length of 1 to 2 in. At approximately the middle of the refining period a 6-in. piece of the impurity-laden finishing end of the bar* was cut off and replaced with new start- ing material. Following refining, the purest 20-in. section of the bar (obtained by discarding approximately 2 in. of the starting end and 8 in. of the finishing end of the bar) was leveled and then analyzed. The AIAG bar was 16 in. long and about 1.2 in. in diameter; it was purified by eight passes of a 2-in. zone at a rate of 1.6 in. per hr, the bar being contained in a sintered alumina boat lined with loose alumina powder of the highest purity. Data for the silicon and copper contents of the three refined bars are given in Table I. Derived data for the efficiencies of the zone-refining operations are listed in Table 11. It is clear from these two tables that the copper is removed much more efficiently—by a factor of 10 to 50 times—from aluminum during zone refining than is silicon. For example, in bar PG3 the thirty zone passes reduced the copper content from 10 to 0.02 ppm, i.e., by 500 times, whereas the same treatment lowered the silicon content by only a factor of about 16. It seem virtually certain, therefore, that the distribution co efficient, k, for silicon in aluminum is well above that for copper and is very likely not much below unity. This also implies that the solidus line on the aluminum-rich side of the A1-Si phase diagram is very probably appreciably curved near the aluminum melting point since the phase-diagram data indicate such curvature is unlikely in the liquidus.

Jan 1, 1965

By E. S. Bumps

A series of macrographs are presented for the purpose of graphically recording the strain phenomenon that accompanies the energy transition in the Charpy impact testing of a mild steel that is susceptible to strain aging. STRAIN patterns in mild steel Charpy impact specimens were obtained in order to determine whether, on the first appearance of plastic strain during deformation, the initial fracture cracks appear in the region of plastic strain or in the elasti-cally deformed regions between. Although this attempt to locate the initiation of cleavage was not successful, the observed strain patterns illustrating various stress conditions in partially deformed Charpy specimens are presented along with a discussion of the possible dependence of transition energy on the yield phenomenon. Earlier work on the development of strain patterns in mild steel have been reported by Fry1 and later by Jevon.2 Harris, Rinebolt, and Raring3 observed characteristic strain markings on the surface of Charpy V-notch impact specimens fractured above and below the transition temperature which they presented schematically. It is intended that the strain figures presented here will add to the literature a graphic correlation of strain with transition energy in impact specimens. Samples of % in. round hot rolled, 0.20 pct C steel were machined to standard 0.394 in. sq, V-notch Charpy impact specimens. Preliminary testing involved determination of transition temperature, Fig. 1, using a Sontagg impact tester. These data were subsequently used to select temperatures above, within, and below the transition range at which specimens were partially deformed. Partial deformation was obtained by either varying the energy or the testing temperature, see Table I. Macroscopic strain figures shown in Figs. 2 to 19 were produced by several metallographic repolish-ing and etching steps. The macroetchant used was as follows:4 120 g HCl, concentrated; 100 ml water; and 90 g cupric chloride. Strain figures were obtained on the outer surface and on sections through the central portion of the impact specimens in order to determine an approximation of the volumetric strain pattern. In the tensile strain figures reported by Jevon, it was found that strain etching would not work immediately following strain unless the material was heated to 200°C. The impact strain patterns presented here were obtained without this heating, but the specimens were not etched until ten months after straining. This confirms a discussion of Jevon&apos;s paper, in which it was pointed out that strain figures can also be developed after aging for long periods of time at room temperature. Hardness of the strained and unstrained portions, revealed by the etched pattern, was explored using R, impressions converted to R, hardness values. Discussion of Results In the impact test, as in the tensile test, some parts of the specimen yield and deform plastically, while other regions are deformed only elastically. The plastic deformation bears a relation to the imposed stress pattern. In the strain figures presented here, the plastically deformed regions are the dark etching ones. The strain figures are always symmetrical because the stress state in the Charpy-type specimen under impact loading is symmetrical. The difficulties encountered to produce initial cracks are intimated in Figs. 2 and 4. At a temperature of —75ºF, the stress was not sufficient to pro-

Jan 1, 1953

By T. M Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the &apos;active masses&apos; of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-&apos; that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By T. M. Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the &apos;active masses&apos; of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-&apos; that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

The Mascot-Jefferson City zinc mining district in eastern Tennessee has been a major zinc producer for over 60 years. The district lies within the Tennessee division of the Appalachian Valley and is underlain by folded and faulted Paleozoic rocks. The local formations are composed of limestones and dolomites with occasional shales, and sand- stones, and thin and scattered chert nodules. The regional structure of the district is unique in that it is complicated by irregular, distorted, and broken anticlines, synclines, domes, and major and minor post-ore folding and faulting.

Jan 5, 1976