Search Documents

By B. L. Averba

THE determination of retained austenite by X-ray diffraction uses the following relationship:"" Pa = constant . RVaA (8) [1] where: P is the diffracted power from phase a; R, the calculated intensity factor; A, the absorption correction; 8, the diffraction angle; and Va, the irradiated volume of phase a For a flat sample making a glancing angle + with the incident beam the absorption correction is calculated as: * 1 sin (28 - 4) A .= 1 [2] µ sin, (28 — 4) + sin 4 where µ is the linear absorption coefficient. Beu3 has proposed that the computed absorption correction be combined with the constant and that the experimental observation of the absorption correction used in the original method be eliminated. This procedure is permissible only if: 1—There is no preferred orientation in the sample, and 2—The geometric requirements have been met precisely. If these conditions are not met the validity of the determination is questionable. Unfortunately the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2. In practice it may be convenient to plot P/R vs the parameter sin (2? — )[sin (28 — +) + sin +] to obtain straight lines for the ap- parent absorption correction. Deviations from straight lines indicate either that the sample has not been positioned correctly or that the relative intensities are incorrect. Geiger counter spectrometer methods also have been used successfully for retained austenite determinations. In the usual spectrometer arrangement the sample makes equal angles with the incident and diffracted beams (8 = ); thus the absorption correction is simply 1/2µ and independent of 8. The retained austenite is then easily calculated from integrated intensity measurements on austenite and martensite lines. If the austenite content is not too low and if excessive fluorescence is not encountered it is possible to use filtered radiation and a recording spectrometer. The integrated intensities are then proportional to the areas of the diffraction peaks. For lower austenite contents the following technique was used: A bent quartz monochromator and a Geiger counter spectrometer are employed. The monochromatic radiation is focused on the front slit, and the counter slit is made broad enough to include the entire line. A series of readings are taken in the vicinity of the diffraction peak. The highest reading includes the diffraction line plus background. The background is obtained from the average of several readings on each side of the peak. The integrated intensity is obtained by subtraction. CrK, and FeKa have been used for such determinations. This technique has been found to be as sensitive and as accurate as the photographic methods. In the spectrometer methods the ratio austenite/ martensite may be obtained from readings on austenite and martensite lines and the application of Eq. 1. It is also possible to use external standards and to obtain the austenite contents from measurements on the austenite lines alone. The small correction for carbides then becomes unnecessary. The best standards are probably samples with known

Jan 1, 1954

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By D. N. Seidman

In the course of a study of the electronic and thermodynamic properties of Pb-Se alloys it was found necessary to have an accurate knowledge of the phase diagram. However, the literature is in disagreement as to whether or not a monotectic reaction occurs in the lead rich portion of the phase diagram. Pelabonl reported only a two-phase region consisting of lead-rich liquid and solid PbSe extending from almost pure lead to the compound PbSe, and gave the melting point of PbSe as 1065°C. The data of Friedrich and Leroux2 are in general agreement with this type of diagram, with the melting point of the compound being 1088°C. However, Nozato and Igaki by inverse rate thermal analysis observed a monotectic reaction isotherm exlacing at 860°C with a monotectic composition of 20.5 at. pct Se. The miscibility gap in the liquid state extends from 7.5 to 20.5 at. pct Se. Hansen and Anderko4 accepted Nozato and Igaki's phase diagram in the region of the lead-rich monotectic. To reinvestigate this portion of the phase diagram, both thermal analysis and metallographic examination of various compositions were performed. The thermal analysis apparatus was constructed according to the specifications of the National Bureau of Standards. A t/t-l pct Rh thermocouple was calibrated against the melting point of copper (NBS), zinc (NBS), and antimony (A. D. Mackay), the emf being measured with a Rubicon Type B potentiometer sensitive to lpv. The absolute accuracy of the thermal analysis obtainable with this system is ± 0.5oC. Starting materials were semiconductor grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999 pct pure with only trace impurities detected upon spectroscopic examination. One hundred galloys were sealed in quartz crucibles with a central thermocouple well under a vacuum of less than 1 p. This procedure prevented any composition change due to vaporization during the run. Cooling curves were obtained on the alloys listed in Table I. Data was taken by the direct method at cooling rates ranging between 1/2 to 2°C per min. The alloys were heated well above the liquidus and shaken vigorously to insure homogeneity. No evidence of an arrest indicative of the monotectic reaction was observed, and the two-phase region reported by Pelabonl and Friedrich and Leroux? was confirmed in general, although our data give higher liquidus temperatures than Friedrich and Leroux. The melting point of stoichiomet-ric PbSe determined for two different samples was 1080.7 0.5oC. The results of this investigation are compared with Nozato and Igaki's data in Fig. 1. To Complement the thermal analysis data, an 86 at. pct Pb specimen was examined microscopically. This composition was in the center of the miscibility gap reported by Nozato and Igaki.3 The alloy was heated to 1000°C, held for 1/2 hr, and water quenched. The specimen was polished using standard metallographic techniques for lead. The alloy was etched with an acetic-nitric acid etchant for 10 min at 45°C. Microscopic examination did not indicate the existence of two separate layers or solidified droplets imbedded in a matrix, as would be expected if a miscibility gap were present. The mi-crostructure shown in Fig. 2 consists of uniformly dispersed, dendritic PbSe in a lead-rich matrix.

Jan 1, 1962

By F. C. Sturges

[CONTENTS PAGE ................. Introduction-Grouting in Mines. By F. C. STURGES. I Use and Technique of Pressure Grouting in the Construction Industry. By V. L. MINEAR . 3 Technique of Pressure Cementing in the Petroleum, Mining, and Construction Industries. By WY. D. OWSLEY and R. E. MOELLER. ..................... 9 An Example of Controlled Pre-grouting in Shaft Sinking. By R. H. ALLEN and J. W. GALPIN. 15 ........ Solidifying Mines and Shafts Areas by Pressure Grouting. By B. H. MOTT 17 .............. Grouting in Southeast Missouri District. By W. W. WEIGEL 20] Introduction-Grouting in Mines By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By R. W. Balluffi, R. Resnick

NUMEROUS investigations of chemical diffusion in a brass have been made and the results are collected in several places.1-3 This work has been mainly concerned with the determination of the chemical diffusivity as a function of composition and temperature. In 1947 Smigelskas and Kirken-dall&apos; showed that zinc and copper diffuse at different rates in face-centered-cubic brass, and since then, a number of efforts have been made to determine the intrinsic diffusivities of zinc and copper in this alloy.1, 5-9 Horne and Mehl8 in particular have recently determined the intrinsic diffusivities as functions of temperature and composition using sandwich-type couples and inert markers. Inman et al." also have determined the intrinsic diffusivities in homogeneous alloys using tracer techniques. When the present work was started, no information of this type was available. Consequently, measurements of the intrinsic diffusivities were made as a function of temperature at a constant composition of 28 atomic pct Zn with vapor-solid diffusion couples where the zinc was diffused into the diffusion couple from the vapor phase. The application of these couples to the study of diffusion in a: brass has been described previously.0,7 The temperature dependence of the intrinsic diffusivities was found to follow the relation D, = A, exp(-Hi/RT) and the values of Hzn, and Hcu, were found to be closely the same. It is emphasized, however, that the chemical dif-fusivity (D = N1D2 + N2D1) is a composite diffusivity and does not necessarily follow this exponential form. It is usually found to do so within experimental error for substitutional alloys because the heats of activation of the intrinsic diffusivities generally are not greatly different.&apos;" Also, at the onset of this work, there was no information available concerning possible unequal diffusion rates of individual components and the existence of a Kirkendall effect in alloys with other than face-centered-cubic structures. Since then, two reports indicating a Kirkendall effect in body-centered-cubic ß brass have appeared. Landergren and Mehl" have published a note describing Kirkendall diffusion experiments with sandwich-type couples. Inman et a1.9 also find a Kirkendall effect in this alloy using the tracer technique. In the present work, several aspects of the Kirkendall effect in ß brass were further investigated using vapor-solid couples. Two different couples were used, one in which the zinc was diffused into the specimen from the vapor phase and the other in which the zinc was diffused out of the specimen into the vapor phase. Briefly, the existence of a Kirkendall effect is confirmed and it is found that Dzn/Dcu = 3 at about the 46 atomic pct composition in this alloy at 600°, 700°, and 800°C. As a result of the unequal diffusion rates of zinc and copper, volume changes occur and subgrain formation is observed in the diffusion zone. In addition, significant porosity is produced by the precipitation of supersaturated vacancies. Diffusion in this alloy is therefore outwardly similar to diffusion in a brass where these effects are also observed, a Brass Experimental Methods—The use of vapor-solid couples in studying diffusion in a brass has been described in previous articles.6,7 The method briefly consists of sealing a copper specimen with Kirkendall markers initially placed on its surface in an evacuated quartz capsule along with a large zinc source of fine a brass chips and then diffusing the zinc into the specimen through the vapor phase. The zinc concentration at the specimen surface rises rapidly enough to a value near that of the a brass source so that the surface concentration may be regarded as constant during diffusion. Under these boundary conditions, values of the chemical diffu-sivity may be obtained by applying the Boltzmann-Matano analysis to the concentration penetration curve, and the intrinsic diffusivities may be obtained from Darken&apos;s5 equations when the velocity of marker movement is known. The diffusion specimens were made from OFHC copper in the form of disks 3.2 cm diam and 0.5 cm thick with faces surface-ground parallel to within +0.001 cm. Markers in the form of fine alumina particles <0.0002 cm diam were placed on the specimen surface. These specimens were then sealed in quartz capsules along with enough a brass chips of a 30.0 atomic pct Zn composition to keep the source concentration from decreasing by more than 0.3 atomic pct Zn as a result of the loss of zinc to the specimen during diffusion. The quartz capsules which were initially evacuated to a pressure of

Jan 1, 1956

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By R. W. Coughlin, W. U. Ault

Experiments in laboratory and mine have clearly demonstrated the usefulness of radioactivity detection for directly measuring the potassium content of potash ore as mined. This paper presents the results of these tests and documents the design of a system for automatically grading and sorting potash ore on the basis of radiation detection. It is shown how the experimental results in the subject mine lead directly to the design of this kind of an automatic control system. The system is capable of grading the ore with an accuracy of approximately ±2% K20 content or better. Due to the usual stratification of the ore body, mining potash seldom presents an extreme problem of gangue separation. Nevertheless, it is frequently necessary to transport within a potash mine and even hoist to the surface considerable quantities of halite and other valueless materials. Up to recent times it has been customary to recognize and route these materials by simple visual and manual techniques. However, the work reported here clearly demonstrates that it is now practical and economical to improve upon these techniques by continuous measurement1 of the naturally occurring radioactive isotope, potassium-40. It was the purpose of the work reported here to investigate this technique and assess its applicability. LOCALE OF EXPERIMENTS The work described here was carried out in a potash mine in Carlsbad, N.M. At the working face of this mine the potash ore is freed by blasting; it is then transported a short distance by shuttle car to a moving-belt system which conveys it to the main shaft where it is hoisted to the surface. Quantities of gangue which are also produced in the mining operation are disposed of in mined-out sections of the mine where possible. Otherwise, this material which contains only a small percentage of potassium (as K2O) must also be transported by the conveyor-belt system to the main shaft and then hoisted to the surface and discarded. With this situation, any measuring device for automatic control purposes must be capable of clearly distinguishing between gangue containing insignificant amounts of K2O and ore containing larger percentages of the same mineral. The conveyor-belt system transports the material from the mine face to a rotary crusher and then to temporary storage pits at the main shaft. This is shown in Fig. 1. Upon leaving the conveyor belt the material enters either one of the two storage pits according to the position of a manually operated gate. It was decided that all experiments should be carried out at the conveyor belt between the crusher and gate with a view to the possibility of providing a signal which could operate the gate automatically. THEORETICAL BASIS AND LABORATORY EXPERIMENTS In principle it is possible to grade potassium-bearing ore on the basis of radioactivity. Natural potassium contains 0.012% K40, which is radioactive with a half-life of 1.3 x 10&apos; years. Although about 89% of the K40 disintegrates to Ca40 by beta decay, the other 11% changes to Ar40 by electron capture and the emission of gamma rays. Unlike the ß-rays which are readily absorbed in the first few millimeters of ore surrounding the disintegrating nucleus, the y-ray photons will escape from an ore sample several inches in size. A detector rigidly mounted under a conveyor belt loaded with potash ore will intercept some constant fraction of all the photons emitted from the ore within its field of view. Under these

Jan 1, 1968

By E. P. Klier, Jane Jellison

The course of the transformations on cooling in a series of Cu-A1 alloys has been followed by means of thermal analysis, X-ray diffraction, and optical metallogrAphy. Specimen size was found to have a pronounced effect on the time of completion of the pearlite transformation due to modification in the unmber of nuclei. The ordeving transformation zvas observed for all cooling rates for all alloys studied, and is considered insuppvessible. At intermediate cooling&apos; rates, a transitional struchire for 011 alloy compositions and based ox the bainite reaction was observed. The alloys of aluminum and copper possess a eu-tectoidal region at from about 9.4 to 16 pct Al. Above the critical temperature, the disordered bcc phase, 0, is stable. At subcritical temperatures, the 0 phase decomposes under equilibrium conditions into the stable phases, a and y,. At the eutectoid composition, these phases develop a lamellar pearlite structure, in appearance much like that found in steels. During rapid quenching from supercritical temperatures, the diffusion processes required for the formation of the equilibrium phases are suppressed, and the 0 transforms to an acicular martensitic phase, designated B or y&apos; depending on the aluminum content, or to a mixture of the two. Early investigators of this system concentrated on determining the equilibrium phase diagram, &apos;&apos;&apos; the structure of the equilibrium phases,3 and later the isothermal decomposition of the 0 phase at subcritical temperatures, or the decomposition of the martensite on tempering. Other work which treated the nonequilibrium transformations concentrated largely on the martensite transformations and the structure of the b and y&apos; phases.15"17 Since the pearlite and martensite transformations in this system resemble those in steels, the one being formed by nucleation and growth of adjacent lamellae of the equilibrium phases, and the other by a diffusionless, shear-type transformation, the present study has been undertaken to investigate the structures formed on continuous cooling, with the objective of constructing cooling transformation diagrams analogous to those derived for alloy steel systems. In particular it was desired to determine whether parallels between the A1-Cu and iron-iron carbide systems on continuous cooling extended to encompass the intermediate phase, namely the bainite structures, which form by a combined martensitic-diffusion mechanism,&apos;&apos; but which are supersaturated with respect to the equilibrium phase upon which their crystal structure is based. To this end the transformations in representative alloys of the Cu-A1 B eutectoid system have been followed, using the methods of thermal analysis, X-ray diffraction, and optical microscopy. EXPERIMENTAL PROCEDURE Materials. The materials tested were those used by Klier and Grmko 5 in their study of the isothermal decomposition of these alloys. The alloys were melted in graphite crucibles and chill-cast into 5 by 2 by 1/4 in. ingots. The ingots were then hot-rolled to sheets 1/8, 1/16, and 1/32 in. thick. The compositions are given in Table I. Specimen Preparation. Specimens for thermal analysis were in the form of small squares approximately 1/4 in. on a side. For the 11.9 and 13.5 Al-Cu alloys, the sheet thickness was 1/16 in. and for the 10.5 A1-Cu alloy the 1/32-in. sheet was used. One lead of a chromel-alumel thermocouple was spot-welded to either face of the square with the specimen itself thus forming the hot junction of the thermocouple. Specimens for X-ray analysis were prepared as filings from martensitic sheet stock and were sealed in glass ampoules under 1/2 atm of argon. Metallographic examination of the powder specimens was carried out on a portion of the heat-treated filings mounted in lucite. All specimens were examined metallographic ally after etching

Jan 1, 1965

By R. E. Smallman, J. C. Terry

J. C. Terry and R. E. Smallman (Llniuersity of Birmingham, England)—In a recent publication53 Wood and Westbrook have reported the results of an investigation of the tensile behavior of fl-phase AgMg alloys. These results agree in broad outline, but differ in the details, with those obtained in the above laboratory and, consequently, some discussion of their paper would seem appropriate. In our experiments, tests were carried out on extruded wires, 2 mm diam, in a hard-beam tensile machine, and while an oil bath was used for the tests up to 150°C, above this temperature the oil bath gave rise to serious contamination of the specimens and hence tests above 150°C were made in vacuo. This procedure is different to that adopted by Wood and Westbrook. The ß-phase alloys exhibit differences in mechanical behavior when they are tested in different temperature ranges. In agreement with Wood and Westbrook, three characteristic ranges are observed which may be classified as low, intermediate, and high temperatures, respectively. Our experiments show that in the low-temperature region, the shape of the stress-strain curves is similar to that reported. However, in addition, it is observed that the temperature at which the low-temperature region ends is markedly dependent on strain rate, and increase with increasing strain rate as shown in Fig. 18. The temperature at which a transition from the low to the intermediate temperature takes place is about 0.4 to 0.45 of the absolute melting point, Tm. This transition temperature coincides with that at

Jan 1, 1963

The curve of Fig. 3 for pyrite requires modification. There 11% a range of pH values from 6.2 to 7.8 for which no cyanide is required to prevent contact. From 7.8 to 11.3 a small amount of cyanide is required, with a sharp maximum of 20 mg. per liter at pH=9.6. The mistake arose from considering too few solution compositions (17 were considered) in constructing the curve. Subsequent work with other collectors indicates that the corrected curve is typical for such systems; it illustrates the further development of the dip in the pyrite curve of Fig. 5.

Jan 1, 1938

A MINING institute open to all men interested in any branch of the mining industry will be held at the Col-lege of Mines, University of Washington, Seattle, during the week beginning March 5. Prospectors, miners, mine owners, persons interested in metallurgy, investors in min-ing enterprises, and the public generally are invited to at-tend. This institute will take the place of the Winter Min-ing Session which originated at Seattle in 1897 and con-tinued for twenty-eight years. The complete new equip-ment of the Mines Laboratory will be used to give demon-strations of new machines and processes of mining, ore dressing, and metallurgy. This year the ceramic industry, including cement and branches of clay working of special Importance in the Northwest, will be included in the insti-tute. All instruction will be given by specialists. Prominent technical men and managers will give lectures on their special subjects. Among the speakers engaged are G. T. Jackson, formerly superintendent of the Alaska-Gas-tineau and the Chichagof mines, who will speak on the mining of large bodies of low-grade ore; R. F. McElvenny, superintendent of the Tacoma Smelter, on the nature of contracts that a smelter can offer to mines and prospects; M. D. Leehey, mining lawyer, on some popular errors re-garding the mining law; H. H. Townsend, on the explora-tion and purchase of prospects by operating companies; J. L. McAllen, on quartz mining in the Willow Creek dis-trict, Alaska; F. Powell, on gold dredging. In the evenings, lectures illustrated by stereopticon views and moving pic-tures will be given. The week will close with an excursion o mines and plants.

Jan 3, 1928

By B. Ladanyi, B. Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a propw knowledge of the distribution of stresses within the slope and their development with time and advancement of workings. There are a uumber of different methods that can be used, in principle, for obtaining this information, such as (1) stress measurement in situ, (2) photoelasticity,1 (3) analytical methods, and (4) numerical methods. In cases where the stress distribution cannot be obtained by classical analytical methods, as in the one considered herein, either photoelasticity or numerical methods are norrnally used. However, actually, due to the rapid development of high-speed computers, increasing preference is given to the numerical methods. Among the latter, the most successful ones, to date, for determining the stress distribution in slopes have been (1) the finite difference method,2-4 (2) the lumped parameter method,5 and (3) the finite element rnethod.6 However, for determining gravity stresses in a natural rock slope, only the finite difference method has been used until now.7,8 A solution of the same problem by the finite element method will be shown here in which a particular reference is given to the development of tensile fracture zones within the slope. FINITE ELEMENT METHOD The stress analysis using the finite element method originates from an extension of the matrix analysis of structures.9 It consists in decomposing a continuous medium, assumed herein to be homogeneous and isotropic,

Jan 1, 1972

By D. Weinstein

The high temperature mechanical properties of stainless steels after fast neutron irradiation are discussed in the light of effects caused by lattice dattmage and effects caused by helium generated from n,a transmutations. Embrittlement at high temperatures is due to helium accumulation at grain boundaries and to cavity formation and proPagation along grain boundaries. Following from the embrittlement mechanism, it is suggested that when deformation occurs by mechanisms associated with super plasticity, helium ac-curnulation at boundaries should be attenuated and cavities, if formed, should be nonpropagating. As the mean free Path between interphase boundaries of a two-phase Fe-Cr-Ni alloy was decreased, the degree of superplastic deforrnation at 870°C increased, as vneaszired by total elongation and by the expottent m = a log &apos;a/a log &apos;i. This alloy and type 304 stainless steel were cyclotron irradiated in an a-particle beam to a helium concentration of -1 x 10 atom He per atom. The stainless steel specimen was embrittled, but the ductility of irradiated two-phase Fe-Cr-Ni alloys correlated with the values of. m during &apos;defor-malion. The .finest grained, helium-injected specimens that deforrned with highest m values exhibited the largest elongations to ,fracture. These results could be correlated with metallographic observations of cavity behavior: the propensity for intergranular propagation was lessened as the m value increased. It is concluded that superplastic deformation is ef-fectizle in attenuating helium embrittlement at elevated temperatures. One of the principal problems associated with development of fast breeder reactors is application of alloys such that suitable fuel cladding results. Stainless steels and other Fe-Cr-Ni alloys, because of highly acceptable nuclear characteristics, represent the primary materials for this component, and an exhaustive research and development effort is being conducted. The main deficiency of these materials has been a severe loss of ductility at high temperatures after fast neutron irradiation. An extensive body of mechanical property data and microstructural observations has provided an adequate phenomenological description of embrittlement; in conjunction with transmission electron microscopy studies, a reasonably acceptable embrittlement mechanism has been obtained. Following from this mechanism, it is suggested in the present work that ductility would be enhanced if deformation could occur by mechanisms associated with the phenomenon of superplasticity. Experiments to test this hypothesis have been conducted, and the results are presented and discussed in this paper. IRRADIATION EMBRITTLEMENT AT HIGH TEMPERATURE Austenitic stainless steels have been irradiated to accumulated fast neutron fluences of 1020 to 1022 nvt at temperatures between 60" and 600°C. Specimens that have been exposed to these conditions and subsequently tensile tested at temperatures between 600" and about 900°C exhibit approximately 5 pct total elongation to fracture.&apos;-3 For unirradiated specimens receiving a nearly identical thermal exposure, total elongation at these test temperatures is about 45 pct. Examination of irradiated specimens has shown that fracture propagation is entirely intergranular. These phenomenological aspects of irradiation embrittle-ment at elevated temperatures are well known and are not generally disputed. Although the explanation of this phenomenon has been controversial, a mechanism for ernbrittlement has emerged that accounts reasonably well for the observed mechanical behavior. The controversy resulted primarily from an indeterminate role of neutron-in-duced lattice damage, if any, and a presumed, but experimentally unverified, contribution to embrittle-ment from helium generated by n,a transmutations. Recently, Holmes and coworkers4 have conducted experiments that separate these effects, and the results are instructive in formulation of the ernbrittlement mechanism. Holmes el al.4 irradiated type 304 stainless steel in EBR-I1 to a fluence of 1.4 x 1022 nvt (E > 0.18 mev); the irradiation temperature was 538" * 48°C or, in terms of absolute melting point, 0.49 * 0.03 T,. After irradiation, tensile tests were conducted at temperatures of 21" to 870.C, the specimens first being annealed for 30 min at each test temperature. In addition, thin sections of irradiated specimens were annealed for 1 hr at identical temperatures, electro and examined by transmission electron microscopy. Thus, for a given temperature, it was possible to correlate mechanical properties with the defect structure. At room temperature, the yield stress of irradiated specimens was a factor of 2.5 higher than unirradi-ated specimens exposed to an equivalent thermal history. Electron microscopic examination of the irradiated specimen revealed a high density of lattice damage in the form of Frank sessile dislocation loops and polyhedral voids. Holmes et al.4 concluded that the presence of this defect substructure caused the increase in yield stress and that after irradiation in a fast neutron flux at 0.49 Tm, substantial lattice dam-age persists. Annealing at progressively higher tem-

Jan 1, 1970

Organization Place Date 1917 American Society of Sanitary Engineers Grand Rapids, Mich. Aug. 1-3 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Safety Council New York City. Sept. 10-15 National Exposition of Safety and Sanitation. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers..:. Philadelphia, Pa. Sept. 10-14 American Institute of Metals Boston, Mass. Sept. 24-29 American Foundrymen&apos;s Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition. New York City Sept. 24-29

Jan 8, 1917

By Arch J. Alexander

COAL is produced, in commercial quantities, in thirty-five of the sty-five counties of West Virginia. Oil and gas are produced, commercially, in forty-two counties. So, you may readily see that coal, oil and gas are closely related as to production areas. Many of the West Virginia coal mines are studded with oil and gas wells, as drilling has been done in thirty-two of the coal bearing counties. When the drilling of oil and gas wells was placed under the regulatory control of the Department of Mines on June I, 1929, it was estimated, by the State Geological Survey, that 64,000 wells had been drilled in West Virginia and that 34,mo wells were then being operated as oil and gas producers. No records of many of these remaining 30,000 abandoned wells exist and some of them remain a standing menace to safety as our coal extraction continues. Of a total of 13,100 new wells drilled since June 1929, approximately 5,200 have been drilled through coal measures. Approximately 7,000 wells, which were drilled through coal measures, have been abandoned in the same period of time. Many of these wells were drilled prior to the enactment of the oil and gas laws. Prior to the enactment of the Oil and Gas Law, which established the Oil and Gas Division of the Department of Mines in 1929, there had been several mine explosions attributable to cutting into un- charted wells and the improper plugging of other wells. The most serious explosion was that of Mines No. 47 and No. 49 of the Consolidation Coal Co. in Marion Co., when one of the so-called plugged wells leaked or seeped through some 80 ft of strata to the coal bed elevation, filling the mine with gas, the gas being ignited, killing a good many men and wrecking two coal mines. Legislation, to combat well hazards to coal mines, was slow in coming. In 1928, R. M. Lambie, then Chief of the Dept. of Mines, got sufficient support from coal, oil and gas interests to get the legislature to pass our present oil and gas laws. These statutes not only protected the coal industry but went a long way toward conserving the oil and gas resources of our state. Before drilling for oil or gas on any tract of land, known to be underlaid with one or more workable seams of coal, the well operator is required to submit a map of the area showing the location of the proposed well, and to send a copy to the Dept. of Mines and a copy to the coal operator. If no objections to the location of the proposed well are made by the coal operator within ten days, a drilling permit and a number for the well are then issued and work may proceed. If, however, the location of the proposed well is objected to by the coal operator, on the grounds that the location of the well will interfere with present mine operations, projected workings, or other- wise Cause a dangerous condition, the operator may file a written objection with the Dept. of Mines.

Jan 1, 1948