Search Documents

By Jack F. B. Silman

Proving up any large, open pit ore deposit by normal exploration drilling under the best of conditions is a noteworthy accomplishment. But, when adverse conditions preclude standard drilling methods, and the same end result is achieved by a relatively new and little known type of drilling, special comment is in order. Three major problems confronted exploration drilling at the Questa molybdenite mine of the Molybdenum Corporation of America-sampling, terrain and time. Surface and underground longhole drilling provided the needed solutions, thus making the greatest single contribution to an exploration and development program that was successful in proving a major, open pit molybdenum deposit.

Jan 5, 1965

By Henry N. Toler

Activity in the search for oil and gas in Mississippi was greater than it had been for several years. Interest manifested and exploration work in wildcat areas were at an all-time peak. Drilling activity in the state's two proven fields continued to decline; there being only four wells drilled in the Jackson field during the year. At the end of 1937 it seems very likely that 1938 will be a big year in the search for oil in Mississippi. Deilling Activity Jackson Gas Field.—The four wells drilled in the Jackson field during 1937 resulted in three producers and one dry hole. Nine producing gas wells were abandoned during the year because of salt-water encroachment. The total production for 1937 was 14,248,000,000 cu. ft., which was a billion and a quarter increase over 1936, the highest year prior to 1937. The grand total produced from the field is 72,341,000,000 cu. ft. of gas and over 15,000 bbl. of oil. The three wells that had produced oil the past few years were also abandoned during the year because of the small quantity of oil and the large volume of salt water.

Jan 1, 1938

By W. H. Bassett

One of the difficulties for many young engineers is the acceptance of responsibility. Even though they start as assistants to older men, they hesitate to offer positive opinions. They often make reports of observations and leave the boss to draw his own conclusions. If they happen to be in a position where they are not reporting to a senior engineer, and it is necessary to take the final responsibility for a decision, they try to get someone to help out and either assume or share such responsibility. Generally this is the result of want of confidence in one's self and fear that something may happen to go wrong and bring about criticism. Frequently diffidence is the principal factor. Young men come to me with reports on work that has been well done and well written up, who are evidently laboring under an intense desire to drop through the floor or to make a rapid' exit in some other way because of want of confidence. In my own early experience a consulting job came in that required considerable investigation. The man who was handing his place over to me mentioned my good fortune and I replied that the work would be interesting and I could handle it all right but feared the responsibility, which seemed considerable. He was an

Jan 1, 1932

ALTHOUGH I have already described to you the procedure for making assays of the ores (a thing that is not very different from what I wish to describe in the present chapter), I shall repeat it in substance, with the addition of the method of assaying gold, in order to tell you certain rules for weights which are very necessary to know, and above all in order to demonstrate to you the method of refining a small quantity of silver by the use of a cupel, and in order to tell you how there are (I find) only two ways that are customary for bringing silver to fineness. One is that of the cupel [copella] and the other is that of the cupeling hearth [cenneraccio], one for a small and the other for a large quantity. But although they are called by two names and appear to be two methods, the aim and the procedure of both is actually the same. Nor do I know of other difference between them than the carrying out of the method and the large or small quantity. Cupeling is a very useful thing for anyone who handles gold or silver to know. Indeed it is necessary, because it not only throws light on the work that is to be done but it also shows the truth [55] and the correct weights in large quantities. It is a quicker and easier way of bringing the work to the desired perfection than is afforded by the method for large quantities. Therefore, as you have heard, it is used in making assays in order to know exactly what quantity of the substance of silver or gold is in copper and lead or in ores, as well as in that melted material which remains among the charcoal and ashes. In short, it is the measure by which you have the certainty and safety of knowing that you have not been deceived by art or by your workmen, who had no other interest than their simple wages. Many workmen are found who are so untrustworthy that they no sooner get control of a thing than they think up some fraud, and even though some know that they must give an accounting they do not restrain themselves, although sometimes they would perhaps act with greater security and more deception than they do if they did not fear detection. For, truly, since silver is a valuable thing and every bit is worth much, a man should not enter into refining it with closed eyes. If for no other reason this pro-

Jan 1, 1942

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By J. H. Wright

Longhole sublevel stopes excavate ore with which the production geologist has only remote contact; therefore, predicting grade and tonnage from such a stope can be a problem. However, the longholes themselves yield data that can be used to improve those predictions. Here, a radial distribution method of weighting sample data is discussed, which is useful in forecasting grade and tonnage from certain longhole sublevel stopes.

Jan 1, 1985

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don't use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By H. A. Guess

AT the outset, said Mr. Guess, I may say that although I believe the present engineering courses in the various colleges and universities could be arranged to give the student within the same time limit a broader general education of un- doubted value, still I do not agree with the view held by many that engineers in comparison with those of other occupations-let us say doctors, lawyers, bankers, and so-called business men-seldom arrive at high executive positions. After all, we must remember that engineers are not very numerous as compared with the occupations just mentioned and therefore a lesser number reaching high executive positions stated numerically might be a larger number stated as a percentage. We all know there must be throughout the United States say three doctors to one engineer, but I don't think that even numerically there are as many doctors in high executive positions as engineers, and it is a fortunate thing for the country that doctors as a class are so busily engaged in alleviating sickness and suffering and in the advancement of medical science that they do not aim particularly for high executive positions.

Jan 1, 1926

By F. B. Eiseman

IT is desired -to determine the effect of the extent of bank repairs on the final slag volume in acid electric steel-melting practice. It is understood that the repairs stud- TABLE I-Summary of Effect of Bank Repairs on Slag Volume [ ] ied here are necessary and the amount of sand added is that needed to maintain hearth and banks in a satisfactory condition. In this way the effect of repair materials on the amount of slag tapped would be found with a reasonable degree of accuracy. Ten heats were made for this study with careful attention to a uniform charge. The steel was the usual grade B and melting was carried out in a 3 1/2-ton top-charge Lectromelt furnace. Melting practice in all cases was the same-complete oxidation, with recarbonization by means of low-silicon pig iron.

Jan 1, 1947

By A. J. Turk, R. G. Dalbke

An increasing number of water pollution control systems are certain to be installed by many industries in the future because of new federal, state and local government regulations, and because of the rising general concern about the deterioration of our water resources. Extensive engineering, some of it based on methods not yet developed, will be required if these new systems are to provide optimum pollution control. Among the primary design factors to be considered are capital cost, operating cost, and present and future regulatory requirements. Establishing A Survey and Test Program To produce a final plant effluent meeting regulatory agency requirements, engineers must have background data that are accurate and representative of present and future plant operation. Operating and plant engineering departments often have available much information, including plant water quantitative and qualitative requirements, both present and future, that can be helpful in the preparation of designs of pollution control systems.

Jan 5, 1968

By C. D. Johnson

Exploration work in 1932 in the Rocky Mountain region, which includes the states of Montana, Wyoming, Utah, Colorado and New Mexico, resulted in the discovery of one new oil field, Cut Bank in Glacier County, Montana; one new gas field, Craig in Moffat County, Colorado; and the definite outlining of a second gas field, Piceance Creek in Rio Blanco County, Colorado, in which there had been drilled but one small gas well prior to 1932. During the year, 95 producing oil or gas wells were completed, giving new initial production amounting to 188,000,000 cu. ft. of gas and 176,420 bbl. of oil per day for the region. By far the largest part of this new production of both oil and gas was developed in southeastern New Mexico, mainly the Hobbs field. However, the Dry Creek field of Carbon County, Montana, contributed over 5000 bbl. of; new oil production. Sixty-two wells were abandoned during the year but of this number only 10 promising structures were nonproductive. The remaining 52 wells had little to recommend their drilling from a structural or strati-graphical standpoint. Eighty-eight wells were suspended in the region' during 1932 before the tests had reached their individual objective horizons. Many of these suspensions were due to financial difficulties and it is possible that several of the operations may be resumed at a later date. At the close of the year, 54 wells were actively drilling, 54 were shut down and there were 20 rigs and locations in the five Rocky Mountain states. The accompanying table gives details of drilling and production.

Jan 1, 1933

By Alexander Anderson

TABLES showing the drift and inclination of wells surveyed in the years 1924 to 28' and in the year 1929' have already been published. Each of these tables included a little over 1,000,000 ft. of rotary hole. In the year 1930 the table -shown-in . Fig. 1, comprising, the results of surveys .of 1,030,344 ft. of hole and representing 11,642 individual survey readings, was compiled. For that purpose we selected 'I only wells that had been drilled in California during that year. The footage of Fig. 1 differs from the two earlier tables in that the wells were all drilled in the year 1930. In the earlier tables, the footage shown was surveyed in the years designated, but some of the wells were drilled in earlier years.

Jan 1, 1931

By M. L. Brashears, R. G. Slayback

The host dolomite of the Pine Point lead-zinc ore is a prolific ground-water aquifer that occurs locally under watertable and artesian conditions. Mining schedules and severe climate require rapid and thorough dewatering of open pits. Pumping-test methods, common to ground-water supply studies, were applied to dewatering design for a model ore pit in 1968. Procedures for testing and design at other ore bodies were established and have been carried out successfully by mine personnel. At the inception of ground-water studies, parts of ore bodies were below prevailing ground-water levels by 35 to more than 150 ft. Movement of ground water through the coarsely recrystallized dolomite occurs largely through fractures and solution openings. Because the overburden deposits consist mainly of glacial till, it is estimated that the recharge to the aquifer is about 25% of the 13-in. annual precipitation. Natural groundwater flow is northeastward toward Great Slave Lake. Background data included extensive diamond drill hole logs and cores and static level data for a number of ore pits. An ore pit, known as N-42, that required 40 ft of dewatering was selected for the initial application of the pumping-test method. Production wells, cased with 14in. pipe, were drilled to a depth of 300 ft on the rim of the ore pit. A suitable pattern of observation wells was obtained by lining 21/8-in. diamond drill holes with perforated electrical conduit. A two-stage pumping test

Jan 1, 1973

By Carl A. Zapffee

FOR a number of years a puzzling phenomenon of brittleness in Class II ferritic stainless steels, developing in the temperature range near 475C, has received increasing attention, but its nature remains essentially unknown. During an investigation of the fractographic structures in stainless steels, conducted in the author's laboratory the past several years, principally under sponsorship of the Office of Naval Research, some observations of a new kind were found for "475 °C embrittlement." While the details of the study cannot be given here,' three fractographs will suffice to carry the

Jan 1, 1952

By Edward Steidle

TWO years ago the Committee on Latin American Education Relations, Mineral Industries Education Division, started a study of mineral industries education in the Latin Americas. Information was obtainable only with great difficulty. Some information was available piecemeal but no complete resume had ever been assembled. Initial assistance was gained from the United States Office of Education and the Pan American Union. This, and first-hand knowledge of the writer, provided a list of colleges and universities which were believed to offer work lead. ing to a degree in one or more branches of the mineral industries. Detailed information could be obtained only by direct contact with each university through air mail service. Questionnaire letters were sent to officials of 34 colleges and universities. Twenty-one gracious replies were received. Fourteen of the colleges and universities concerned offer curricula in mining, five in metallurgy, three in petroleum, seven in geology, one in geographical engineering, one in topographical engineering, and one in geophysics. Two institutions offer advanced training in petroleum engineering. No institution offers any courses under the caption of ceramics or fuel technology.

Jan 1, 1945

By Nathan C. Rockwood

WHILE mining engineers have been searching in far corners of the country and of the world for hidden wealth there has grown up around us in nearly every city great wealth-producing mines calling for the investment of hundreds of millions of dollars and yielding products now sold for over half a billion dollars yearly-largely unknown and almost wholly neglected by mining engineers. But this neglect is explainable and excusable. They are industries of very recent origin-practically the growth of the last 25 years. They are in a very large measure the result of tremendous developments in engineering construction and the rapidly expanding use of portland cement concrete for structures of every description. Concrete as a material of construction is going through an evolution very much as did cast iron and other metals used in engineering; and this phase of the industry should appeal to the imagination of metallurgical engineers. At first iron was iron-a material of uncertain properties, owing both to small differences in chemical composition and in methods of manufacture. By successive steps iron was studied and knowledge of its properties developed-the striking effects of very small percentages of other minerals and of various heat-treatments.

Jan 1, 1924

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By O. P. Arora, I. L. Caplan, H. von E. Doering

ThE interpretation of X-ray and electron diffraction data obtained in plastic deformation studies of hcp a titanium requires knowledge of angular relationships between crystallographic planes and directions. Rarey el 01.' have calculated both interplanar angles and angles between directions for a number of c/a ratios. This information, although useful for approximate applications, does not provide exact data for specific hcp metals. Recently, Hu2 has tabulated interplanar angles specifically for hcp titanium. The present study augments the existing data on titanium by providing the angles between plane normals and rational crystallographic directions in addition to interplanar and interdirectional angles. These angular relationships were calculated on an IBM 360 Computer using a Fortran IV program.* Cal-

Jan 1, 1969