Search Documents

By Titus Ulke

About two years ago, in making an examination of the Etta mine for the Harney Peak Tin Co., I discovered, in a vertical secondary quartz-vein in the granite massive of Etta mountain, the mineral about to be described. The vein was from a few inches to 3 feet wide, and was exposed for a length of about 15 feet. It was

Jan 1, 1893

Jan 1, 1936

By John B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about ½ -in. water pressure. No loss of air was evident.

Jan 7, 1958

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb and Kombat mines. The Kombat mine, owned and operated by Tsumeb Corp. Ltd., is located in the Otavi Valley in the northern part of South West Africa, approximately 213 air miles north of Windhoek and 38 air miles south of Tsumeb, at latitude 19° 43'S and longitude 17º 41'E. The mine is linked to all major centers by both national railroad and tarmac highway systems which pass right through the town. The Otavi Minen- and Eisenbahn-Gesellschaft (OMEG) mined ore on the farm Asis from 1908-1925. Tsumeb Corp. Ltd. acquired the mineral rights in 1947, started diamond drilling in 1954 and commenced mine development in 1960. The mill started production in 1962 when proven ore reserves were 3,378,084 st containing 2.85% Cu and 2.90%Pb. Annual production of 248,411 st was increased in May, 1967 to the rate of 422,990 st, which was still being maintained in 1971, when ore reserves stood at 3,054,701 st of grade 1,91% Cu and 2.5% Pb.

Jan 4, 1973

Discussion of the paper of E. W. Parker, presented at the New York meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 443 to 451. A MEMBER :-I would like to call attention to the fact that the speaker has failed to indicate where is the center of gravity of the membership of the Institute, while he is dealing with this map. MR. PARKER :-I think you will find that a little further east. CHAIRMAN JAMES F. KEMP :-In connection with Mr. Parker's paper, I would like to inject a little matter of history into our program here, as regards the founding of the Institute. The credit for the founding of the Institute really applies to miners who were engaged in the anthracite coal region. The three men who signed the circular for the call for the meeting which brought the engineers to Wilkes-Barre in May, 1871, were Eckley B. Coxe, Richard P. Rothwell, and Martin Coryell.

Jan 5, 1913

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By Bunting S. Crocker

Bunting S. Crocker (Executive Vice President, Kilborn Engineering Ltd., Toronto, Ont., Canada)-This is an interesting report on laboratory-scale testing with pebble charges in 12-in.-diam mills, and the author correctly concludes that useful laboratory testing can be done. In the opening paragraphs he states, "laboratory pebble-milling tests have been considered too difficult to perform and not relevant enough to the actual grinding situation"!! This is definitely not so! The writer published detailed tests done in a 12-in.-diam mill comparing pebble and steel balls in 1952 6 and again in 1954 7. We note that our review paper in 1963 was the only one mentioned in the References. The author states that "a smooth lining is more frequently used in commercial-scale pebble grinding." The writer has designed some 22 plants treating 134,000 tpd in North America and Australia. He has also visited pebble installations in Norway, Sweden, Finland, and South Africa. All these plants correctly use heavier lifters than would be considered standard for ball mills of a similar size. Smooth liners are not recommended in wet ore treating plants. In the 1952 paper6 it was clearly demonstrated in the test work that the individual ore pebbles had to be the same weight-not the same diameter or size-as the steel balls if comparable grinding results were to be obtained. In the tests performed in this study most of the pebbles "passed 50-mm round hole screen openings and remained on a 40-mm round hole sieve. Correspondingly most of the ball mill experiments were performed with 50 or 40-mm steel balls". Thus, the balls and pebbles were essentially the same size or diameter. This means we are comparing apples and oranges. When the feed being ground is fine enough the pebbles will be superior. When the feed is coarse the steel balls will be the better. This is similar to grinding tests in which two sizes of steel balls are compared. In the middle of the article, "Crocker5 has reported that equal weights of pebbles and steel balls achieve the same grinding capacities under similar conditions …", then he proceeds to question this postulate. In the eight reports that I have published, I have never made this statement. What I have said is "for comparable grinding, the individual pebbles in the mill charge should be the same weight as the individual steel balls." This is not the first time that I have been misquoted on this point! It is most unfortunate that this test work has been done with a ball and pebble of the same diameter and not the same weight. It is impossible to properly evaluate the results. I also regret the fact that the screen analyses of the tests were not shown. Many of us who have been 40 years or less in the grinding game can easily read screen analyses at a glance. We can tell whether the top meshes are being ground by the ball charge, etc., etc. The graphs are fine for the summary or to illustrate conclusions but are often misleading in the report itself. However, we do agree that useful pebble grinding tests can be done in a 12-in. mill.

Jan 1, 1973

Two sessions during the recent AMC Mining Convention in Los Angeles, September 23-26, served to update industry personnel on the status of health and safety regulations in the US. As reflected by the American Mining Congress resolution on mine safety and health, "Based on experience with the federal Coal Mine Health and Safety Act of 1969 and the federal Mine Safety and Health Act of 1977, (AMC) does not believe that laws designed to force compliance with regulations through the imposition of criminal or civil penalties will result in safer mines. (AMC) feels that the government's participation will be much more productive if greater emphasis is placed on research, training, and inspections aimed primarily at assisting operators and employees in recognizing and eliminating hazardous conditions and practices.

Jan 11, 1979

H. S. COE, St. Louis, MO. (written discussion *)-I feel much gratified that Mr. Mishler has confirmed those principles of slime settlement expressed by Mr. Clevenger and myself. I wish to state that, when we wrote the article referred to by. Mr. Mishler we had not seen his earlier article in which he gave a formula to be applied to the settling rate off feed pulp for determining thickener area required at El Tigre. It has been my experience that in cyanide work the settling area required is determined by the settling rate of the feed pulp for perhaps 20 per cent. of all of the ores to be encountered. For the other ores, the area required is greater than that indicated by the settling rate of the feed and corre-sponds to the settlement of a somewhat thicker free-settling pulp. Mr. Mishler, in his paper, has thoroughly outlined a set of tests for determining thickener capacity, which, if carefully carried out, should be entirely reliable, provided allowance is made for changes in the mill feed from time to time. Two features of his paper, I, believe; need comment. In speaking of the time required for slime to flocculate after being fed, Mr. Mishler quite properly states that the actual settling rate for the feed pulp can-not be that of completely flocculated pulp because of this time lost in flocculation. It seems to me, however, that this feature cannot be of very great importance, for the following reason: The upper zones of pulp in a thickener may be, and often are, as thin as the feed pulp. If, therefore, the feed be introduced at sufficient depth below the pulp surface to prevent agitation at the surface, there will be ample time for it to become flocculated before it becomes the surface layer, and it, will

Jan 1, 1918

mean to say that these explosions are mechanical, but that the ejectment of the stock, throwing out of tops, etc., are mechanical. I see no reason at present, although I have had almost no experience in the use of large quantities of Mesabi ore, to change my ideas on the subject. That these explosions should follow irregular working or slipping in the furnace, I think can be explained. I have noticed that immediately following slips there is little or no settling of the stock on top, although there is no lessening of the volume of gas passing into the stoves and boilers. Supposing that, after a slip of 3 or 4 feet, the filling continues, but for some distance from the 'top the stock fails to move: there would be a much better chance for the deposited carbon to clog interstices in the stock, and for the additional effect in the same direction of the fine ore in the charge, than if the stock were properly settling. Under such conditions it is easily supposable that the openings would be entirely closed, or closed so tightly that the pressure below the obstruction would be raised to a point approaching the blast-pressure, or to a point high enough to force a passage or an enlargement of the small passages which may remain. When this occurs, gas from below under pressure carries with it large quantities of deposited carbon and fine ore; if the case is aggravated, coke, stone, bell, etc. As soon as the red-hot deposited carbon meets the air there are perfect conditions for a dust explosion, which naturally follows, the same as in a coal-mine or flour-mill.

Jan 1, 1899

By Edward H. Robie

AT a recent meeting of the AIME Board there was considerable discussion of a suggestion that companies should be more interested in promoting AIME membership among their employes. The advocate of this idea argued that companies benefit greatly if their employes are active AIME members, so even on purely a selfish basis they should use various means to encourage membership. Also he argued that companies in general make no contribution to the support of the AIMS although benefiting from its work, so should not object to making more of a contribution, financial or otherwise, than they do. One Director stated that an investigation had developed the fact that a large majority of members felt it unwise for employers to pay the initiation fees or dues of employes. They felt that AIMS membership should be on a purely personal basis; that the rewards of active membership were sufficient so that it is a good investment for a man in developing his own professional stature, presumably resulting in an increase in salary sooner, or in greater amount, than would otherwise be the case. If an employer paid a member's dues or initiation fee the member would take less interest in the Institute. But this Director felt that an employer should otherwise encourage his employes to join the Institute, attend its meetings, and write papers based on company work for presentation and publication. Another Director reported that his company pays the expenses of AIME members in its employ to meetings; the company also encourages nonmembers to attend AIME meetings but does not pay their expenses unless they present papers of interest to the company. Another Director, representing a supplier, stated that his company's policy was to send some of its staff to all AIME meetings at which papers of interest were to be presented or at which valuable contacts could be made.

Jan 1, 1952

By Fred C. Bond, Fred T. Agthe

WHEN some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material, and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different texture and composition exhibit great differences in coating potentialities. Various materials were tested in thg laboratory to show the variation in coatine qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feldspathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been

Jan 1, 1940

MISSOURI SCHOOL OF MINES On the tenth of January, 1919, a meeting was held by the juniors and seniors for the purpose of reorganizing the Missouri Mining Association. The reorganization was brought about in this manner because at that time there were no old members left in school. At that meeting, the following officers were elected for the remainder of the year: Gerald F. Rackett, president, Harland H. Hoppock, Secretary. The Association has held several interesting meetings and is arranging interesting programs for some to be held in the future. At present the Association has thirty-four members. H. H. HOPPOCK, Secretary.

Jan 5, 1919

By Glenn Alvey

THE measure of value of an oil property is approximated by the length of time it takes to "pay out;" viz., the time required for it to return the original investment. This time varies in different fields. In the Appalachian and Mid-Continent fields, a good investment pays out in about four years; in California, it requires a slightly longer time; and in the Gulf field about two years. The two principal methods for establishing these values are based on acreage, as in California, and on production, as in the Appalachian field. The method of establishing values based on production1 was worked out in the Appalachian fields and approximates the value remarkably well in some fields; but it is a rule of thumb and should be used intelligently. Briefly, the method is as follows: An arbitrary number of dollars (called the barrel-day price) multiplied by the number of barrels of settled daily production of the property gives the value.. In its crudest application, the barrel-day price is determined by the "$10 to $.01" rule, which means that the barrel-day price is one thousand times the prevailing price of oil. For instance, with oil at $3.50 per bbl. the barrel-day price would be $3500 per bbl. This rule, however, is not strictly applied, for the, barrel price is varied according to whether or not the wells "hold up." But when a barrel price for a district has been fixed it is quite general to raise or lower the price with the fluctuation in the price of oil; here the" $10 to $.01" rule is used extensively. However, the prospective purchaser takes into account tangible equipment upon the property, the extent to which the drilling program has been carried out, whether or not the wells are "shot" or natural, depth of wells, spacing of wells, paraffin trouble, etc.

Jan 1, 1921

By W. J. Garmoe

Distinct areas of mineralized and non-mineralized brecciated rock are found in the Ontario Unit of the United Park City Mines. These breccias contain an appreciable fraction of the present ore reserves and probably will become even more important as deeper levels are developed. Three ages of breccia have been recognized in the Ontario Mine to date: ( 1) Pre-mineral breccia that may or may not be mineralized, (2) early post-mineral breccia with mineralized fragments, and ( 3) late post-mineral breccia that is younger than and cuts through ( 1) and (2) above. These age ,relations are known from detailed underground mapping. Locally, both pre-mineral and post-mineral breccias have sufficient lead-zinc-silver content, either as matrix or fragmental material, to constitute ore. Ore-grade breccias occur throughout a vertical range of over 1000 feet and are found in both the Humbug and Deseret formations from above the Ontario 1300 level to below the Ontario 2200 level. The mineralized breccias, which are difficult to distinguish on mine maps, are not well delineated by underground workings, and their horizontal outline and vertical extent are not known beyond the immediate mining areas. The greatest amount of truly mineralized breccia is exposed on the 2200 level.

Jan 1, 1968

By Kenneth G. Arne

INTRODUCTION The real problem is finding the "appropriate" financing sources by matching the risk and reward expectations of the various classes of investors and lenders. Generally, lenders who advance funds temporarily are interested in assuming only limited risk and conversely expect to earn only a limited reward. The equity owners on the other hand, are expected to take most of the risk of the enterprise, but should receive a reward commensurate with that risk. In particular they will receive the benefit of the company's increase in net worth over time. MINE DEVELOPMENT CYCLE Consider the development cycle of a mining project beginning with rank wildcat exploration (Figure 1) [ ] Just as different professionals must be utilized at different stages, so must different funding sources be used at different points in the pipeline. Figure 2 shows the general sources of funding: [ ] This concept can perhaps be better understood if we compare the risk with the capital requirements. Suppose each area within a triangle is proportional to the risk taken (see Figure 3): [ ]

Jan 1, 1985

By L. D. Muller, C. P. Sayles

When minerals are mined in arid or semiarid areas where water is at a premium, dry processing is a natural route to take for concentrating or classifying the values. Until recently though, dry processing technique were limited by the lack of suitable equipment. With the advent of the pneumatic pinched sluice at Warren Spring Laboratory, Stevenage, Hertfordshire, England, a new tool emerged to fill this gap and it has the potential of providing industry with a high output concentrator or preconcentrator for dry natural ores and secondary materials. The pneumatic pinched sluice gives every indication of fulfilling these requirements with the added advantage that with homogeneous materials-such as crushed limestone or quartzose sands-it may alternatively operate as a high throughput dry classifier or sizing device. An industrial version of the equipment is now being manufactured by Dryflow Separators Ltd., as sole licensee for the National Re- search Development Corporation.

Jan 1, 1971

[ ]

Jan 1, 1907