Search Documents

By Charles Himrod

IN presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: 1st. Kind of fuel. Bituminous coal not permitting the formation of as much CO2 as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by not allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO,. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a, manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

Jan 1, 1877

By David C. Grant, Erich W. Tiepel

In situ mining is a process for recovering uranium from relatively small or low grade ore bodies. The process involves passing a lixiviant and oxidant, typically NH4HC03 and H202, through a uraniumcontaining ore body. As the solution progresses through the ore body, the uranium is oxidized from the plus four to the soluble plus six state. The bicarbonate complexed uranium laden solution is removed from the ore body and the uranium recovered in an above-ground processing plant. During the leach process lixiviant cations may be sorbed on the ore host, if the host contains exchangeable clay minerals. This report examines the implications of this clay interaction on ground-water quality, the various available in situ mining restoration methods, laboratory procedures for simulation and development of those methods, and the results of using the restoration methods in the field. Various restoration methods, including ground-water sweeping, clean water recycle, and chemical restoration are presented and discussed. The use of ore characterization, agitation leach tests, and column tests to study cation sorption and desorption, and thus, to identify and evaluate restoration methods is discussed. Ore characteristics identify the clay type and clay content, which allows the estimation of the magnitude of the cation sorption by that ore. The chemical effects of clay exchange and of chemical restoration can be examined using agitation leach experiments and packed ore column tests which also provide information on the physical effects. The agitation leach test is a relatively rapid means of determining the sorption and desorption characteristics of an ore. Unlike agitation leach tests, column tests can be used to assess the influence of solutions on permeability, on precipitation problems, and on other chemical changes. The effectiveness of using restoration methods, which were developed and tested in the laboratory, are examined by presenting field restoration data from several mining sites.

Jan 1, 1979

E. B. WILSON, Scranton, Pa. (written 'discussion *).-Prof. Young's paper shows another application of electricity in solving problems in coal mining, and suggests that it may be possible to utilize the data he has collected in developing an electric firedamp detector. If electric lamps are to be adopted in gassy coal mines, the use of an electric firedamp detector becomes almost imperative, for safety lamps and electric lamps in the same mine are not always conducive to safety, and Liveings electric firedamp detector, is too cumbersome to meet with general approval. Three well understood facts are verified in a new way by Prof. Young's experiments: - 1. The temperature at which methane ignites. 2. The more inflammable gas present in an atmosphere, the hotter will be the flame, and the longer the cap in a safety lamp. 3. As the temperature at the source of ignition varies, the length of the gas-cap flame varies. Prof. H. B. Dixon collaborating with Mr. H. F. Coward, some years ago, made experiments on the ignition of various gases to find the tem-perature of their kindling points.1 From the results of their experiments, the writer has culled the ignition temperatures of some hydrocarbon gases, and has tabulated them with other data, in Table 1.

Jan 10, 1919

By John D. Morgan

THE tense international situation prevailing in the postwar period, and the outbreak of actual hostilities in Korea, directs attention to the status of United States reserves of strategic and critical materials for war. Geologists and mining and metallurgical engineers are particularly interested in this problem, since, with a few important exceptions, almost all of the materials on the official list of strategic and critical materials for stockpiling (see top of page) are metals and minerals.

Jan 3, 1951

By C. F. Jackson

THE work of, the Mining Methods Committee is now well under way. Following discussions previous to and during the February meeting, an Outline for Papers on Mining Methods was prepared, and over a thousand copies have now been distributed to committee men, to section secretaries and to members who have indicated any interest in the subject. The objective of the committee is to prepare a symposium on mining methods which will be of real practical value to the operator and engineer in the solution of every-day mining problems. It is planned to cover the entire field of mining in such a way that the different branches of mining, such as coal and ore (iron, copper, lead, zinc and precious metal) can benefit from the experience of the others at points where they have problems in common.. It is realized fully that each of these branches of mining possesses its own peculiar problems, but at the same time, there are prob-lems in connection with each, where the experience in others should be of value. The committee proposes to proceed along the following lines: 1. To present a general classification of mining methods, showing their inter-relationship, and at the same time .provide a common language for the discussion of mining methods and a nomenclature that will have the same meaning wherever used. A com-plete set of illustrations will accompany the classi-fication to make clear the terminology adopted and to show graphically the inter-relationship of methods. 2. To show the relationship between the physical characteristic of the deposit, the economic consider-ations and the. mining method., It is not proposed to treat this subject as a mere academic problem, but to secure reports from every mining company of impor-tance in this country, which will show what methods or modifications and combinations of methods have actually been applied and the physical conditions and economic considerations which have led to the adoption of these methods in each case. The Mining Methods Committee has drawn up an Outline for Papers on Mining Methods to be distributed among mining engineers and operators, giving in detail the information desired. This outline is the result of several months of careful thought and is a composite of the suggestions of many engineers and mining company officials from all parts of the United States.

Jan 7, 1922

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By J. D. Vincent, Paul A. Weyler

Climax Molybdenum's plan for the Henderson 30,000 tpd molybdenite plant didn't just happen. It slowly evolved over a period of 3% years. Many plants cannot afford similar delays, but the Henderson project will take about 10 years to complete from the time the orebody was first discovered until production begins. Pilot plant testing results with both the single stage and two-stage semi-autogenous grinding circuits were highly favorable in terms of operating costs reduction-so much so, that the Amax subsidiary made the decision to go with semi-autogenous grinding for the Henderson mill.

Jan 5, 1972

By K. Hanumantha Rao, T. C. Rao, M. Vanangamudi

The effects of important variables such as pulp density, feed size, furnace oil dosage, degree of agitation, and time of agglomeration on the yield and ash content of the agglomerates obtained from the oil agglomeration of coal fines have been studied in a laboratory batch agglomeration cell. Optimum conditions for maximum yield and throughput have been discussed. The furnace oil dosage and pulp density were found to have more influence on the yield and grade of the agglomerates than the degree of agitation and feed size in the ranges studied.

Jan 1, 1983

By John A. Church

AT the last meeting of the Institute, a discussion arose upon the question, Is there pressure in coke ovens?" and many of the members seemed to think that the superiority of the Belgian furnace might be due to the fact that it is a completely closed chamber, in which the gases given off by the coal are, or may be, at more than the atmospheric reassure. It seems to me that this position is untenable, 'and that an examination of one of these ovens in operation will show, not only that there is no excess of pressure in the coke chamber, but that the contrary is true, and a partial vacuum exists. The Belgian or Francoise oven consists of a rectangular chamber closed at the ends by sliding doors, and furnished with flues in the side walls and floor. The new charge is introduced at a time when the furnace is so hot as to cause immediate and copious discharge of the volatile constituents of the coal. The gases pass downwards through the side flues giving out their heat to the walls and thus to the coal. Underneath the floor air is introduced and the gases burn, producing intense heat. Heat is also reflected from the arched roof upon the coal which is therefore heated from all sides. The especial advantage which this construction was designed to secure is that no air is admitted to the coke-chamber. All the heat is produced by the combustion of the unsociable gases, and the yield ought to be a maximum. I t is so in fact, allowing for the imperfections inseparable from furnace construction and management. Sometimes the yield is in excess of the percentage indicated by assay, showing that

Jan 1, 1935

By Magnus Troilius

The method of using the bromine process of determining sulphur in steel, described below, is in successful use at the Midvale Steel Works. Ten grams of drillings are weighed out and put into the 1/2-liter flask A, with long neck. The flask is connected with a wide glass tube C', which, in its turn, is connected with the absorption bulbs B, containing HCI, 1.12 specific gravity, and ahout 5 C.C. of bromine. The wide tnbe C causes the vapor to condense and flow back into the flask A during boiling. The bulbs B connect with a long glass tnbe, which may be made to carry off the bromine fumes through a hole in a window, or, better still, through a flue with powerful draught. The connections being made, 100 C.C. of boiling water are run in through the thistle tube T. The air is thus completely driven out of the flask. 100 C.C. of HC1 (about 1.19 specific gravity) are then run in. When the gas begins to run rattler slowly through B, heat is applied until boiling gradually ensues. The steel being completely dissolved, the apparatus is disconnected, and the contents of B rinsed out into a beaker of 100 C.C. capacity, into which a few C.C. of a concentrated solution of BaCI, have been previously introduced. Heat is then applied (best by means of the hot iron plate) until the bromine is completely driven off and the BaSO, has settled nicely to the bottom. The BaSO4, is then filtered off on a small

Jan 1, 1884

By V. GUDKOV

THE iron-ore deposits of Russia were estimated at 2,200,000,000 by the Russian Geological Survey, in 1910; but this estimate must be considered as being far too low. The estimate for Siberia, which had been explored very little for iron ore, was placed at about 27,000,000 tons. The exploration, in 1912-14, of the three iron deposits-Blagodat, Baakal and Kamensk-raised the estimate of the iron-ore reserves or the Urals from 282,000,000 tons to about 400,000,000 tons. Conservative estimates of the explored deposits made by the writer in 1915, gave the following figures: Southern Russia 900,000,000 tons, Ural Mountains 500,000,000 tons, Central Russia 900,000,- 000 tons, Siberia 100,000,000 tons, Caucasus 20,000,000 tons, or a total of 2,420,000,000 tons of iron ore, or 1,200,000,000 tons of pig iron.

Jan 1, 1921

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust- collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market out- lets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk so-ton lots direct to the consumer. POTENTIAL MARKETS FOR FINE- MESH COAL DUST In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, “sea coal” distributing plants, water-purification plants and obviously, pow-

Jan 1, 1944

By A. H. Lindley, Fraizer M. Stewart

For many years large mining companies were able to finance nearly all of their capital requirements from internally generated funds. However, during the last decade, funds needed for capital expenditures, dividends, and scheduled debt retirement have grown faster than cash flow. As a result the minerals industry has had to rely increasingly on other sources of funds. Getting the capital for new mining projects is a challenge, particularly for smaller companies. New methods of financing and new variations to old methods have been developed and more are needed. Commercial banks are short-term lenders. By policy their loans are limited to low risk loans-those made solely on the borrower's general credit, and secured loans where cash flow is sufficient to provide repayment within a comparatively short term. To maintain liquidity, banks prefer to make loans of less than seven years' term. If a longer loan is needed an insurance company or pension trust may take the long-term part.

Jan 1, 1971

Jan 1, 1946

CALAMINE is one of the semiminerals that have great similarity to the metals. It is a very heavy mineral earth of a yellowish color. It is found in Germany near the lead mines and in Italy in a mountain between Milan and Como. It is also found, as I have heard, in other places, as at Fosini in the territory of Siena. I believe that it is almost certain that some exists there because there are many other kinds of minerals there- about, although none is mined there in these times. But this does not mean that it could not be mined or that there is not some there that is real. Someone says that he med to melt what he could find with copper [36v]

Jan 1, 1942

Jan 1, 1940

By J. J. Rutledge

The United States Bureau of Mines established at Bruceton, Pa., in 1909, an experimental mine, for the purpose of testing the means of preventing and limiting mine explosions. During the last ten years numerous explosions have been caused to originate in this mine for investigative purposes and the rate of propagation of the explosion wave, the pressure developed per unit of area by the explosions, and the general results of the explosions have been carefully recorded and studied. Means of preventing mine explosions or of limiting them to the areas in which they originate have been developed. A great deal of valuable information has been derived from the work in this mine and much more useful and Valuable information will be obtained in the future. The writer would plead, not for the opening of experimental mines in all the important coal-producing fields in the United States, but for the opening of demonstration mines, or mines in which experiments could be made with the various details of coal mining. The United States Department of Agriculture has established, in nearly every state, stations that undertake experimental work for the benefit of the agricultural interests. In addition, small demonstration plats are set aside, in suitable locations in the farming districts, where various crops are grown under scientific direction, so that the faimers in the neighborhood can note the results obtained and profit thereby. Something like this should be done for the coal-mining induatry. If experimental or demonstration mines were established, methods of working adapted to local conditions could be worked out. Owing to competition in the same markets, small capitalization, or low profits, it may be an utter impossibility for any one company to try a new method of mining. Labor conditions may prevent the trial of a new method of working. It may be impossible or inadvisable to disturb existing working conditions for fear of causing trouble among the miners through real or fancied changes in the scale of wages. The first and most important investigation to be undertaken in these demonstration mines would be the trial of various methods of working coal mines until a satisfactory plan had been demonstrated for each

Jan 1, 1920

APPROXIMATELY 26 percent of the total ore production to date from the largest single deposit of copper-bearing material in the world was mined during the war years, 1942 to 1945, at Chile Exporation Company's great open-pit mine at Chuquicamata, Chile. About 18 percent of the total waste removed during the life of the mine was handled in the same period. The total of ore and waste represents approximately 24 percent of the total material that has been excavated from the pit. This is more than was removed in the first fourteen years of operation from 1914 through 1927. The pit at Chuquicamata is 17/8 miles long, 1/2 mile wide, and has a present vertical extent of 817 ft between the top of the highest bench and the lowest bench being worked. However, when

Jan 1, 1948