Search Documents

By Walter F. Pond, Kendall E. Born

Production of crude oil in Tennessee during 1935 approximated 20,000 bbl., an increase of about 5000 bbl. over 1934. The total production for the state is an estimate, since the only definite figures available are those for Scott and Morgan counties, where 12,377 bbl. were marketed during 1935, an increase of 4305 bbl. over the preceding year. The oil fields of Scott and Morgan counties are near the eastern margin of the Cumberland Plateau where Pennsylvanian sediments rest uncon-formably upon the Mississippian. Near Glenmary, in Scott County, the production is from the middle Mississippian, probably near the top of the St. Louis limestone. Accumulation is due to a low, east-west anticline which has been cut by a fault. This field is now 20 years old and only a few wells are pumped at present. Oil was Struck along Boone Camp Creek in Morgan County in 1924 and there has been small production since that time. The oil comes from the middle of the Fort Payne formation of lower Mississippian age at a depth of 1400 ft. Geologic work in the area has shown that a terrace and porosity conditions in the Fort Payne formation account for the accumulation. The production figures on a number of small producing wells in Clay and Overton counties are not available. As pointed out by Glenn1, the installation of small local skimming or topping plants in the fields has curtailed the shipment of crude oil out of the state and as a result it has been impossible to secure accurate production figures in these counties. The operators, in most cases, are reluctant to give information, and there is no state law requiring them to do so. Based upon information available to the writers, it is believed that between 7000 and 8000 bbl. is a fair estimate of the production in Clay and Overton counties during 1935. More than 500 wells have been drilled in Clay County, the majority of which were drilled east of Cumberland River. Some eight small oil fields have been developed in the county within the past 12 years, a

Jan 1, 1936

By Kendall E. Born, Walter F. Pond

Production of crude oil in Tennessee during 1935 approximated 20,000 bbl., an increase of about 5000 bbl. over 1934. The total production for the state is an estimate, since the only definite figures available are those for Scott and Morgan counties, where 12,377 bbl. were marketed during 1935, an increase of 4305 bbl. over the preceding year. The oil fields of Scott and Morgan counties are near the eastern margin of the Cumberland Plateau where Pennsylvanian sediments rest uncon-formably upon the Mississippian. Near Glenmary, in Scott County, the production is from the middle Mississippian, probably near the top of the St. Louis limestone. Accumulation is due to a low, east-west anticline which has been cut by a fault. This field is now 20 years old and only a few wells are pumped at present. Oil was Struck along Boone Camp Creek in Morgan County in 1924 and there has been small production since that time. The oil comes from the middle of the Fort Payne formation of lower Mississippian age at a depth of 1400 ft. Geologic work in the area has shown that a terrace and porosity conditions in the Fort Payne formation account for the accumulation. The production figures on a number of small producing wells in Clay and Overton counties are not available. As pointed out by Glenn1, the installation of small local skimming or topping plants in the fields has curtailed the shipment of crude oil out of the state and as a result it has been impossible to secure accurate production figures in these counties. The operators, in most cases, are reluctant to give information, and there is no state law requiring them to do so. Based upon information available to the writers, it is believed that between 7000 and 8000 bbl. is a fair estimate of the production in Clay and Overton counties during 1935. More than 500 wells have been drilled in Clay County, the majority of which were drilled east of Cumberland River. Some eight small oil fields have been developed in the county within the past 12 years, a

Jan 1, 1936

By A. B. Kinzel

SILICON and its metallurgical uses have been the subject of speculation since the earliest days of modern civilization. The early philosophers, Theophrastus and Pliny, believed that silica was a special form of ice, an opinion that was not seriously challenged until the seventeenth century. The first comprehensive view of the nature of silica was advanced by Lavoisier in 1787. He assumed silica to be an oxide of an unknown metal. In 1808 Berzelius produced ferrosilicon by heating silica, iron and charcoal. Probably the first produc¬tion of crystallized silicon was in 1854 when H. St. C. Deville accidentally produced the material while electrolyzing a double chloride of aluminum and sodium containing siliceous impurities. It is not strange that the early investigators should have given so much attention to silica and silicon, because of the great natural abundance of the former. Although silicon does not exist in the elemental state in nature, it has been estimated that the lithosphere contains approximately 60 per cent silica; quartz and rock crystal are found in practically every part of the world.

Jan 1, 1933

By M. P. Sidorova, D. A. Fridrikhsherg

The surface charge, electrokinetic potential and surface conductance were studied for silica, alumina and rutile as the functions of PH and concentration of 1-1 electrolyte solutions. The adsorption potentials of potential-determining and specifically adsorbed ions were calculated from isoelectric and zero charge points on the basis of Stern equation and thermodynamic description. From surface conductance and charge data the mean ionic mobilities in double layer were estimated. The results give some information about the real structure of oxide-electrolyte interface and gel-layer concept.

Jan 1, 1980

By Walter W. Fisher, Samuel Rudy

Secondary treated sewage effluent was substituted for normal process water in laboratory tests simulating froth flotation recovery of copper and molybdenum sulfides. Sewage effluent caused significant detrimental response in the flotation process. First, a voluminous, uncontrollable froth was generated, even in the absence of a frothing agent, that has little mineral carrying ability. Second, sewage effluent caused a small loss in copper recovery and a large loss in molybdenum recovery. The detrimental effects of sewage effluent on flotation were partially overcome by tertiary treatment of the effluent by activated carbon adsorption and anion exchange. The frothing problem was significantly reduced after treating the sewage effluent by foam fractionation. Dilution of the effluent with normal process water resulted in a significant improvement in metal recovery. In addition, the large loss in molybdenum recovery was overcome by using a secondary collector in a combination reagent schedule. However, the secondary collector caused an appreciable loss in copper recovery.

Jan 1, 1979

THE Boston meeting, August 29-31, was in many ways one of the pleasantest the Institute has enjoyed in years. Much hard work had been done by the committee, and with excellent results. The program had been purposely restricted with the idea that a smaller, more homogeneous audience formed the best basis for a regional meeting, and the event fully justified the plan. The one hundred and sixty-three members and guests attending were dominantly interested in geophysical methods or their application, and, despite the highly technical character of the papers and the unusual heat, attendance and interest in the technical sessions were well sustained. The exhibition of geophysical instruments and aerial maps added greatly to the meeting.

Jan 1, 1928

By John F. Abel

Personal gain seems to be the most powerful incentive to economic progress. One of my first exposures to this phenomenon was the comparison between company stopes and leaser's stopes in a vein gold mine. The company stopes were 4 to 6 ft wide, whereas the leaser's stopes were so narrow that in some places one could not turn around. The company leased only that ground it felt was marginal to mine with day's- pay miners, but by skillful, careful and energetic mining, the leasers managed in most cases to make money for themselves and the company. The Hurting Truth This capitalist system, which puts a premium on successful risk taking, is under attack. Not that it hasn't been under attack all along. What hurts and angers us at this time is that the attack comes from the children of the system-its youth. Such blasphemy should, of course, be eradicated, root and branch. Or should it? Are we hurt in part because some of the things they say are true?

Jan 1, 1970

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By David W. Wisecarver, James F. Reynolds

INTRODUCTION The Department of Energy is cooperating with Snowmass Coal Company near Carbondale, Colorado to introduce the longwall mining method in moderate to steeply pitching coal seams in the United States. This venture is part of a coal mining research program directed toward development, trial, and analysis of mining technique8 to improve production and recovery in the more difficult mining conditions such as thick, multiple, and steeply pitchly seams found in the Western U.S. The project at Snowmass is the first attempt in the United States to operate a longwall in a steep coal seam. Plans are to mine three adjacent, successively downslope panels in the eight foot thick seam which varies in pitch from 27 to 33 degrees. During this work, researchers and mine engineers are expected to obtain answers to many engineering questions relative to panel design and development, selection of face equipment and beet operating techniques and procedures. They are also committed to obtaining hard data on costs, recovery, production, safety, and behavior of underground mine structure as the three panels are mined. This information is essential to future mine engineering and profitable mining of pitching Western coal reserves. Development of the first trial panel was begun in 1979 and completed in June 1981. The longwall mining equipment was then installed in the starting room and retreat mining begun on August 11, 1981. Project duration is expected to be about five years during which over tm million tons of coal will be produced. TRAINING The longwall mining method is new to Snowmass. For years the mine produced coal by room and pillar methods using conventional techniques to mine upslope rooms and Alpine F6A miners to cut entries and rooms on strike. Miners were experienced in room and - pillar mining from other mines. News of the longwall demonstration was received enthusiastically by Snowmass miners. Employee interest in the project was 100%. However, there was minimal longwall experience on site. In fact, most of the work force had not even seen a longwall. Mine and company management were well aware of the immediate need to develop trained longwall face mining crews and maintenance people qualified to work on longwall equipment and also expertise in longwall planning, equipment selection, power distribution design, ventilation requirements and panel development. The first approach to answer this huge deficiency in longwall mining experience was obviously training. Hence a training program directed toward those mining specifics most urgent to the beginning mining phases was initiated in mid-1980. Classroom lectures and hands on training, using instructors from equipment suppliers and available company longwall expertise, was conducted in longwall subjects to include face mining procedures, panel development, operation of equipment, equipment assembly and maintenance, electrical circuitry and controls, ventilation, move of longwall equipment, and safety procedures. At the same time, responsible engineers and foremen were sent on a tour of European pitching longwalls to see first hand how other mines working under similar seam conditions conducted their operations. Development techniques, types of equipment, methods for transport of men and materials, and ground control techniques were discussed with engineers, foremen and officials at each mine. This look at European longwall mining operations gave Snowmass good insight into the unique problems associated with longwall mining on 30' pitch. Mining considerations such as face conveyor/ support system slippage downslope, panel development, maintenance, safety considerations, manpower requirements, and haulage methods were covered with European experts

Jan 1, 1982

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge This can best be done by the presentation and discussion of technical papers by its members Short practical papers are especially welcome An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author Members are urged to submit papers presenting the results of their work Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts

Jan 1, 1952

By Merrill, Charles White

MOST extraordinary of the technical developments in placer gold mining during the last five years has been the rise of the dragline dredge, by which is meant a floating washing plant for auriferous gravel, fed by a dragline excavator. The idea originated in the fall of 1933, when Horace Onyett constructed a floating washing plant to which gravel was delivered by a dragline excavator standing on dry land. Onyett's operation near Oroville, Calif., and another started by H. F. England later on Wyandotte Creek, Butte County, Calif., yielded '75 oz. of fine gold before the end of 1933. Although the first operation was abandoned shortly as un- profitable, the dragline-dredge method of gold recovery soon began to expand at a boom rate. As a matter of interest, the Onyett operation was taken over later by Lord and Bishop, who are re- ported to have succeeded in making it the first financially successful drag- line dredge. In California alone drag- line dredges produced $3,294,970 worth of gold in 1937, and the pros-

Jan 1, 1938

By AIME AIME

THIS year the Chairman of the Institute's Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

By Henry A. Wentworth

(New York Meeting, February, 1912.) ELECTROSTATIC separation of ores in its present form is generally known as the Huff' process from the name of Charley H. Huff, of Boston, Mass., through whose constant and persistent labors (with the invention of Clinton E. Dolbear as a basis) the successful commercial process embracing separative machinery and the various electrifying devices has been developed step by step, and the finances for the long period of development provided, and the method finally established and recognized throughout the world as an important and successful addition to the ore-dressing department of metallurgy. The permanent field-success of electrostatic separation began in 1908 with a 20-ton Huff experimental mill built specially for the purpose by the American Zinc, Lead.& Smelting Co., in Platteville, Wis., a plant which was a success from the start and was gradually increased in capacity as the market-conditions warranted to 100 tons of concentrates per day. Much credit is due to the above-mentioned company for its initial venture, and for its assistance in applying the process to field use. Prior to 1908 electrostatic separators had been installed and operated (but for a comparatively short time, however) in a number of places; some under the patents of Mr. Dolbear by himself and associates, and some under the patents of Lucien I. Blake and Lawrence N. Morscher, by W. G. Swart, mining engineer, of Denver, who has always been a courageous advocate of electrostatic separation. Due to the difficulties experienced in the generation of the electrical charges, the primitiveness of the separators, the wooden construction instead of iron as at present, the lack of control of the electrical fields and other difficulties overcome by the later inventions of the Huff Electrostatic Separator Co.,

Jun 1, 1912

By E. E. AGGER, Arthur Notman

THE proposal has been made in a bill introduced into Congress at the last session by Representative Jones of Michigan that an import duty of 6 c. per lb. shall be placed on copper. This action is urged after eighty years of prosperity for the industry in this country; during most of which copper has been on the free list, and during all of which a tariff would have been without real effect. To comprehend the general situation upon which this action would be imposed, we must refer to the past history of the industry and its trends at the present time. The following table supplies us with a picture of the physical growth of the industry in this country and its relation to that of the world as a whole down to Jan. 1, 1921:

Jan 1, 1925

By C. S. Smith

QUANTITATIVE methods were used to good effect in the earliest days of metallography1-3 but they mysteriously passed into virtual disuse until the important paper4 by Howard and Cohen in 1947. Various devices for the measurements of integrated linear intercepts have been constructed, primarily by petrographers. The hydraulically operated stage designed by the writer5 was satisfactory, but prolonged use caused air bubbles to become entrapped, which introduced back-lash. A new stage has been constructed which avoids this defect and provides better integration when measuring directional structures. This utilizes a circular traverse, and integration is achieved by counting electrical pulses produced by a photocell and a light chopper.* The stage is shown diagramatically in Fig. 1 and in photograph, Fig. 2. It is of simple construction. Mounted on a plate with clamps to fit the stage of a standard metallurgical microscope is a worm and 100-tooth worm gear, the latter supporting the specimen to be measured. The worm is manually actuated by a knob which contains inside it three

Jan 1, 1961

By C. Richard Tinsley, Ta M. Li

Accelerated development of the deep-ocean and continental margin resources may be the ultimate answer to meet rapidly increasing material demands to the year 2000. The mineral-rich oceans that have been described as "vast" and "nearly inexhaustible" have to date remained virtually untapped. Mineral Dependencies Trigger US Interests A lack of known domestic reserves of selected commodities and a climbing mineral trade deficit that reached a record $19 billion in 1974 are two factors that have sustained US interests in deep-ocean and offshore mining over recent years. But the lack of federal leadership in formulating ocean mining policy is said to have significantly discouraged the major capital commitments necessary to develop these resources.

Jan 4, 1975

Jan 1, 1966

By R. Malmstrom, H. Heden, K. Likin

Sublevel caving techniques at Luossavaara-Kiirunavaara AB (LKAB) in Sweden have undergone significant modification over the years as management strives to maintain mine viability amidst rising costs and erratic iron ore prices. LKAB, which is 96% state-owned, is Sweden's principal iron ore producer and operates three iron mines north of the Arctic Circle. By far, the largest of LKAB operations is the Kiirunavaara (Kiruna) underground iron mine which extracts an estimated 30 million t/y of ore, Other iron mines include the Malmberget underground nine, rated at 12 million t/y of ore, and the Svappavaara open-pit mine, rated at about 4.5 million t/y. Mined ores from Kiirunavaara and Svappavaara are shipped by rail to the northwestern harbor of Narvik, while Malmberget ores are sent to Lulea, located to the southeast. LKAB iron ores are marketed by Malmexport AB, which is owned jointly by LKAB and Granges, Sweden's base metal producer.

Jan 10, 1979

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather ciosely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general infor-mation as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars.

Jan 1, 1937

By A. D. Hoagland

The Flat Gap mine is located on Copper Ridge in the Appalachian Valley of East Tennessee. Large zinc orebodies occupy zones of solution and collapse breccias in Lower Ordovician Kingsport limestone and dolomite. The principal ore mineral is sphalerite and the principal gangue is dolomite. The ore-bearing horizons are considerably more than 95% covered by thick residual clay. Geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap mine. The Flat Gap mine, an important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolcrmite and accessory pyrite. There is local minor galena and very rare barite and fluorite. The ore-bearing horizons are covered by about 20 to 100 ft or more of residual clay except where active streams have exposed bedrock. Considerably less than 5% of the favorable host rocks are exposed in outcrop, and this nearly complete soil cover creates a serious obstacle to exploration. Comprehensive surveys of the base metal content of soils furnish a useful substitute for outcrop geology, and under favorable conditions, this technique is a very valuable prospecting tool. The analysis is carried out by a titrametric dithizone method modified after the procedure described by E. B. Sandell.' This method detects

Jan 1, 1962