Search Documents

By C. S. Corbett

EARLY in the development of every oil field, the operators of relatively large tracts of land must decide upon a spacing plan for the wells to be drilled upon their respective tracts. Usually it is desirable to have a system of regular spacing laid out over the entire tract, making such adjustments as may be necessary near land boundaries. Unless the dip of the producing formation is very steep, the equilateral triangular arrangement is the one most generally preferred, for the very good reason that it gives the maximum amount of drainage area for the wells up to the limit at which mutual drainage interference begins. Assuming that the equilateral triangular pattern is to be used, there still remains to he decided the matter of distance between wells. Many variable factors enter into the problem of proper spacing, some of which are physical and some economic. It is not the purpose of this paper to discuss these factors, as that has been done in several comprehensive articles during the past few years. In the end the decision must be based upon an estimate of the relative importance of various factors which apply to the field in question and to economic conditions in the oil industry at the time the development is getting under way. Even if the best possible spacing distance should be chosen when the problem arises, changing economic conditions and variation in physical conditions in different parts of the field may cause the original choice to become more or less unsatisfactory. Obviously, it is advantageous, once a spacing plan has been adopted, to avoid alteration of it as the field becomes better known or as conditions in the industry change, and yet be able to vary somewhat, the acreage per well in extending the area of development. Or, it may be desired to provide for an ultimate spacing considerably closer than conditions seem to warrant early in the development of the field. With these contingencies in mind, it is of interest to examine the possibilities which the equilateral triangular system affords. Orientation of Coordinate System In this system the well locations may be considered as the inersectionst of three sets of coordinate lines, the lines of each set intersecting those of the other two sets at 60. For convenience in placing such a system

Jan 1, 1930

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936

By Milton H. Ward

INTRODUCTION Historically, planning a mine involved the economic decision of whether to mine by open-pit methods or underground methods. The method selected was influenced by a number of factors, including size, tenor, and location of the deposit. If the project could not be justified by either underground or open-pit practices, it remained in fallow until economic conditions changed or technology advanced. Technology has advanced and the mining industry now has another option, that of in situ leaching. This method is on the threshold of becoming a commonly used alternative for production in many types of metal and mineral deposits. It will be utilized as the primary method for developing an ore body or as an adjunct to open-pit or underground operations. The following considers application of the technique to a deposit that had been partially exploited by open-pit methods. HISTORY The Big Mike Copper Mine is located approximately 30 miles south of Winnemucca, in Pershing County, Nevada. Interest in the property dates from the turn of the century, but little exploration was undertaken until the mid '60s. In 1967 Cerro Corporation acquired the property and initiated a major drilling effort. Ranchers Exploration obtained the property after this exploration program in late 1969 and confirmation drilling was undertaken. The deposit was delineated and it was determined that reserves amounted to about 100,000 tons of 10.0% massive copper sulfide ore and 700,000 tons of 2 .O% mixed oxide-sulfide ore. The ore body was a lenticular deposit, dipping at 50°. The massive sulfide mineralization was chalcocite and

Jan 1, 1974

There are no authentic records of production prior to 1869, although various records report local production and use in 1853 and 1860. Tonnages in Table 68 for the years 1853-1868, both inclusive, are estimated. [ ]

Jan 1, 1942

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year's production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country's total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931

By AIME AIME

TOTAL shipments of iron ore from the Lake Superior district totalled 21,672,410 long tons in 1933, according to a compilation in Skillings' Mining Review. The producers ranked as follows in order of output shipped:

Jan 1, 1934

By S. G. Lasky

Abraham Lincoln is reputed to have said that if you want to chart a course to some destination, you have to know where you are starting from. In this instance we have to define our starting point in a double manner: 1) What was the theoretical basis of the Paley predictions? 2) What actually did the Commission predict, so that we can see how the predictions have worked out up to now as a basis for considering how they may have to be changed.

Jan 3, 1960

By John H. Bassarear

By 1968, Cyprus Pima was milling 34.5 kt /d (38,000 tpd) of copper ore using a conventional flowsheet consisting of three stages of crushing, rod milk and ball, mills. A 13.6 kt /d (15,000 tpd) expansion was put onstream late in 1971 using primary crushing, semiautogenous milk, and ball mills. Identical ore is treated in both concentrators. This paper shows the weight and life of each liner for each crusher and each mill over a four year period from 1974-1977. Media consumption is shown for the same period and a comparison is made between the two reduction methods.

Jan 1, 1983

By Allen D. Gorrison

EFFORT to develop fundamental quantitative information and improved technique in the production of petroleum has long been faced with difficulties of a particularly evasive nature, owing to a combination of circumstances. In the first place, petroleum comes from far below the ground, out of sight, so that information derived from indirect observations must be extrapolated to reservoir conditions. If one does not force the analogy too far, the petroleum engineer may be said to be somewhat in the position of the astronomer. The actual phenomena which he wishes to observe in detail appear at a place so deep in the earth?s crust that personal observations and direct experiments are impossible.

Jan 1, 1942

By Guillermo Hileman

Probably the outstanding feature of the oil industry in the Argentine, during the past year, was the increase in production from the Comodoro Rivadavia field. This increase was accounted for by the discovery of a deeper producing horizon in the old coastal field (zone A). The oil, derived from the deeper sands, served not only to balance the natural decline of the upper sands and increase the yield from the area, but also provided a product of comparatively superior quality. The finding of this ney- production in the old field had a special economic significance because of the pumps, tanks and pipe lines already installed to take care of it. The deep horizon is looked upon as a life

Jan 1, 1937

Salt Lake City was founded July 24, 1847, by Mormons under the leadership of Brigham Young. It had a population of 1 18.1 10, according to the United States census of 1920, and of 15 1,968, according to a civic survey, January 1, 1925. The Salt Lake metropolitan district is estimated to have 180.079 inhabitants. The city's area is 5 1.8 square miles. Its altitude is 4,354 feet. It has 514 miles of streets, of which 91 miles are paved. The streets in the main portion of the city are 132 feet wide and the blocks are 660 feet long. It has 144 miles of street railway and 2,200 electric street lights. It has fifteen parks and playgrounds, forty public schools and six private schools. It has eighty-nine church edifices, of which forty-nine are devoted to denominations other than the Mormon church.

Jan 1, 1925

By Thomas F. Downing

When examining a coal property it is customary for the engineer to take channel samples at several coal faces. In doing so the extraneous matter, or partings, which can be removed by hand, or mechanically, with the facilities at hand, or proposed, is rejected. Where there is doubt concerning a stratum it is usually rejected from the main sample but part is taken for separate analysis. The samples are forwarded to a chemist for proximate analyses and determination of British thermal units, and, sometimes, ash fusion. Consideration is given all available commercial analyses but frequently the owner presents only the favorable ones. From the results thus obtained a general evaluation is made, monies are loaned or expended, markets are determined, and realization is estimated. In many instances, such grades are not substantiated and it is time we looked deeper for a basis which will prove more practical. Institute committees are working hard on analytic and use classifications and much valuable information has already been assembled and distributed. However, no single grade can be applied to any particular bed or region. Much study has been given the Pittsburgh No. 8 seam, yet that bed is subject to material differences in a single section;i. e., some strata of a face may differ from others in structure and analysis, particularly in sulfur content. From some localities it yields a good carbonization fuel, while in others it is chemically unfit for such use. Traveling south to the Logan, W. Va., field we find the Cedar Grove (Island Creek) seam a hard, gray splint coal., In the same field, and not far distant, the same bed changes, both structurally and chemically, and consists of excellent gas coal. In Illinois the moisture content of a bed may vary greatly in different localities. We have seen mines in which part of the coal is excellent for special purpose use but is spoiled by the product from another part of the same mine. Many other illustrations could be given but these are sufficient to show that application of any grading of coal must be distinctly local. The actual designation of grade can be given only after detail study of the component parts of the seam, or seams, on the property under considera-

Jan 1, 1932

In explanation of the delay, which may have been noted by members of the Institute, which has affected both the Bulletin and Volume .59 of the Transactions, we may mention that our printers, in common with nearly all publishing concerns in the country, have recently been overwhelmed with work on text books and similar technical matter required in connection with the education of the student-army recently inaugurated by the Federal Government. Although we regret the delay in the issuing of our periodical, we cannot help feeling- that our publications are perhaps second in importance to the needs of the army. It is to be hoped that the present excessive demand for printing of- this sort will soon be passed, after which we shall resume publication with more punctuality.

Jan 11, 1918

By M. M. Fidlar, Ralph E. Esarey

Conditions in the oil and gas industry in Indiana were somewhat better in 1936 than in the previous year, owing in large part to increased

Jan 1, 1937

By Kendall F. Born

Production of crude oil in Tennessee during 1939 was slightly more than 51,000 bbl., an increase of about 10,000 bbl. over 1938. The product,ion by counties and by fields is shown in Table 1. The increased production has rcsulted from continued activity in the Upper Cumberland district, especially in Clay County, where approximately 37,000 bbl. were marketed off the lease. This figure includes a single well in the old Tinsleys Bottom pool on the Clay-Jackson County line, although the well is in Jackson County. The "Mississippi lime" produced 10,811 bbl. in Scott and Morgan Counties, a decrease of 2568 bbl. from the 1938 production. Production during the year from some half-dozen scattered wells in eastern Clay, Pickctt, and Fentress Counties, on which there are no accurate figures, is estimated at 1000 barrels.

Jan 1, 1940

By Kendall F. Born

Production of crude oil in Tennessee during 1939 was slightly more than 51,000 bbl., an increase of about 10,000 bbl. over 1938. The product,ion by counties and by fields is shown in Table 1. The increased production has rcsulted from continued activity in the Upper Cumberland district, especially in Clay County, where approximately 37,000 bbl. were marketed off the lease. This figure includes a single well in the old Tinsleys Bottom pool on the Clay-Jackson County line, although the well is in Jackson County. The "Mississippi lime" produced 10,811 bbl. in Scott and Morgan Counties, a decrease of 2568 bbl. from the 1938 production. Production during the year from some half-dozen scattered wells in eastern Clay, Pickctt, and Fentress Counties, on which there are no accurate figures, is estimated at 1000 barrels.

Jan 1, 1940

By T. A. Klinefelter, O&apos, R. G. Meara, Glenn C. Truesdell, Richard W. Smith

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

Jan 1, 1920

By George Dyott

THERE are many who may consider a paper on aerial transport and its possibilities in connection with mining operations somewhat premature. Nevertheless, as there is considerable interest manifested in the subject at the present time and the amount of information available is both scanty and misleading, the result of investigations in some of the remote mining districts of Peru will not only be of interest, but will help crystallize, in the minds of many, a more correct conception of just what an airplane is capable of doing. By way of introduction, I will deal briefly with the types and varieties of airplanes now in use, and the developments of the past few years, pointing out -how the war has encouraged machines. of startling performance rather than those of commercial utility. I will then take up aerial transport in general, showing how airplanes may be employed to advantage and the particular kind of work for which they are best suited. This will cover a preliminary discussion on cost, which is one of the most important phases of the subject. In passing on from a general survey of the situation, I will deal with actual observations and investigations made in Peru. This part of the paper will be divided into two sections: the first, covering the mountainous districts of the Andes (Tamboras, Pataz, Soledad, etc.); the second, the alluvial deposits in the rivers, Chinchipe, Santiago, and Napo. In each case the question of atmospheric conditions, altitude, landing grounds, motors, cost, etc. will be discussed. While it is my intention to deal chiefly with mining in the sections mentioned, the same line of argument will be applicable to any other districts in the world. In conclusion, I will touch on the possibilities of using lighter-than-air craft of the Zeppelin type, followed by a summary of the most salient points brought out in the paper.

Jan 2, 1919