Search Documents

By Erwin Zodrow, De Verle P. Harris

The Smallwood mine, owned and operated by the Iron Ore Co. of Canada, is one of the largest ore producers in Canada, producing about 15 million tons of crude ore per year. Located in the Labrador Trough near, Labrador City, Newfoundland, the open-pit operation has ore consisting chiefly of specular-hematite, with some magnetite. The magnetite content of the ore as a mineral percentage is small, but it is of considerable importance in ore grading because of its effect upon milling. Being harder than specular-hematite, magnetite increases grinding time and milling costs. Specifically, higher grade magnetite (greater than 15%) usually occurs as fine grains in a fine grained siliceous rock matrix (also as larger octahedra in carbonate bands). This tends to increase the overall breaking strength in the crude ore; consequently, the hourly mill rate and the weight recovery decrease. At the same time, because of its relatively high iron content, the magnetite does contribute to the amount of iron in a block of ore. Were the concentration of the magnetite relatively constant, its presence would be of less consequence, for appropriate adjustments could be made in the milling operations. However, the quantity of magnetite present for any run of ore varies considerably; it is the magnetite prediction for a block of ore that constitutes the greatest problem in grading. THE PRESENT ORE GRADING METHOD Ore for the Smallwood mine is graded by a computerized block grading routine (using 50 x 50 x 45-ft blocks) that applies simple weighted (inverse-distance) averaging to ore grades. The results of the block grading program are not reliable with respect to magnetite concentration. Factors responsible for this poor estimation are (1) the structural setting of the deposit, and (2) mineralogical relationships. Neither of these general factors are given adequate consideration by present methods.

Jan 8, 1967

By Harold F. Yde

Hydraulic tailing fill in the Butte deep-level mines resulted from studies made in 1958 by The Anaconda Co. Mining Research Department. At the time of the study, dry mine tailing was hauled via rail cars from the Anaconda tailing ponds, 25 miles distant, to the tailing fill plants of the underground mines at the Leonard, Anselmo and Mt. Con mines. Presently, tailing from the Weed concentrator in Butte is delivered to the Kelley shaft via pipeline and stope filling has become automated. Tailing at 30% solids is pumped 8000 ft horizontally and upward from the concentrator to the Kelley fill plant, where it is dewatered and deslimed by three Krebs cyclones. These discharge the material into the cased and grouted mine delivery boreholes at desired densities of up to 70% solids. The vertical boreholes and 4-in. rubber-lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the 3-in. stope-filling, unlined Victaulic pipelines.

Jan 1, 1970

By William Romanoff

IN AN ARTICLE on "Recovering Smelter Dust and Oxide," published in the Engineering and Mining Journal (Vol. 131, No. 2), the authors briefly described some dust-recovery equipment and its operation at a secondary-metals brass-smelting and refining plant. A description of our experience in overcoming certain operating difficulties may prove of interest or value to those who are confronted with some of the same problems or who should equip their furnaces with dust-collecting equipment. The dust loss from reverberatory smelting and refining of brass con¬sists largely of zinc, with smaller percentages of lead, tin, and copper in the order named. At the Kramer plant, the fume discharge from the two stacks amounted to 3 to 4 tons of solids per day, making a dense smoke. With dust equipment in operation, the discharge from the stacks is invisible and approximately 2500 lb. of zinc and other metals is recovered daily thereby from each furnace operating.

Jan 1, 1933

By GUY C. RIDDELL

THE recent purchase by an American investment trust of a substantial block of shares in a British owned Venezuelan copper operation directs attention to mining activities that have been quietly gaining momentum in that country for a number of years. We hear so much of oil work in Venezuela that attention to its metal-mining activities is in most quarters casual. In gold and copper the country has made some interesting mining records, and two of the old districts are ,digging in for a come-back. Copper Copper production centers in the state of Yaracuy. The Aroa-Cumaragua mining region has had a long and eventful history. The Aroa mine itself, 50 miles from the coast in West-Central Venezuela, was discovered in 1605. First mined in 1632, owned at one time by Simon Bolivar, it has been reopened many times and is now , the basis of substantial operations by the South American Copper Syndicate, Ltd. of London. The latter has operated the property profitably, off and on, for a number of years, paying heavy dividends on a small investment-at times over 300 per cent annually.

Jan 1, 1929

By James Terry Duee

No important producing developments took place in Colombia during the year 1928. This was at least partly due to the paralysis of operations by the passage, during the latter part of 1927, of a law which was regarded by the oil companies as confiscatory and unjust, and the promulgation of exceedingly stringent regulations of this law under decree No. 150, published Jan. 28, 1928. This decree, which contained 24 articles, practically prevented not only producing operations by the oil companies but even such activities as geological explorations and surveying, as severe fines were imposed for the possession of maps not registered with the Ministry of Industries. Both this regulatory decree and the law were subject to attack in the courts by several of the oil companies. The regulatory decree was suspended May 22 by Presidential proclamation, until the suits against it are decided by the Supreme Court and Council of State. Though another law was introduced into the Colombian Congress at a later date, no action was taken on it, and at the time of the writing of this paper, it would appear that no oil bill will pass the Colombian Congress during the present session. The Barco concession, which was revoked in February, 1926, still continues an unsettled matter, although there have been rumors that the government was attempting to come to some decision on this rather difficult question. A hopeful sign toward the close of the year was the settlement of negotiations with the Tropical Oil Co. over the acceptance of the payment for royalties due the government from that company. This settlement, which covered a royalty on crude oil produced from June 30, 1926 to June 30, 1928, represented a cash payment for approximately 3,000,000 barrels. It is to be hoped that during the coming year the Colombian government will see its way clear to clarify its position on petroleum legislation. A good augury for the future was the statement made by President Abadia Mendez on New Year's Day, in which he courageously admitted the errors of previous legislation and said, regarding oil, "Very soon

Jan 1, 1929

By K. R. Y. Simha

Successful explosive gas well stimulation requires a thorough understanding of explosively driven cracks under confining in-situ stresses. In a previous paper (Simha, et a1 1983) the problem of explosively driven cracks was experimentally investigated to reveal the features of crack propagation. It was observed that the explosively driven crack propagation is the result of two different but overlapping phases. The first phase involving the initiation and early time crack propagation is entirely governed by the explosively generated stress transients. The rapidly decaying stress transients then lead to the second phase of crack propagation largely controlled by the in-situ stresses. The purpose of this paper is to more fully understand the characteristics of the first phase concerning the initiation and early time propagation of explosively driven cracks. Experiments are conducted with plastic models under biaxial compression and the dynamic event is observed with a high speed multiple spark gap camera of the Cranz-Schardin type. The experimental observations are utilized to propose analytical models of crack initiation under explosive loading to aid in the design of multiple fracturing necessary for successful application of modern well stimulation techniques.

Jan 1, 1984

By Kyle Wightman

INTRODUCTION CRA Limited is the largest mining group in Australia by value of sales and the second largest company in Australia in terms of share market capitalisation. In the past 25 years, CRA, its predecessors and affiliates have been involved in a number of mining and further processing developments in Australia and elsewhere. Many of these have been financed using project financing techniques. These include Comalco's development of the Weipa bauxite deposits in Northern Queensland in the late 1950's, the Hamersley iron ore developments in the Pilbara region of Western Australia in the mid 1960's, the Queensland Alumina Limited alumina refinery in Gladstone, Queensland, at about the same time, and the Bougainville copper project in 1969/70. In the past three years CRA has again utilised project financing techniques to fund its Tarong steaming coal project in Queensland, the Blair Athol steaming coal project also in that State and CRA's interest in the Argyle diamond project in the Kimberley region of Western Austrlia. PROJECT FINANCE DEFINED Nevitt Definition Nevitt's is the most frequently quoted definition - "A financing of a particular economic unit in which a lender is satisfied to look initially to the cash flows and earnings of the economic unit as the source of funds from which a loan will be repaid and to the assets of the economic unit as collateral for the loan." Risk and Balance Sheet Treatment It is important to focus in more detail on two aspects of project financing, risk and balance sheet treatment. The assessment of the various elements of risk in a project and the sharing of that risk between sponsors and lenders is the most critical feature. At one end of the spectrum is full absorption of risk by the sponsor(s). This can be described as "on risk" or "on credit" or "full recourse" to the sponsor(s) and is effectively a corporate financing. At the other end of the spectrum the lenders absorb the whole risk in a non-recourse financing which is "off risk" or "off credit" for the sponsor. The other aspect is the sponsor's balance sheet treatment. If the balance sheet of the economic unit undertaking the project and the financing need not be consolidated into the balance sheet of the sponsor (because ownership does not exceed 50%) then the financing may be described as off-¬balance sheet. If consolidation is required then the financing is described as on-balance sheet. Most project financings involve some recourse to the sponsor, i.e. they are limited recourse. Very few are non-recourse or off credit to the sponsor. Limited recourse financings may be on-balance sheet although many may also be off-balance sheet insofar as consolidation is concerned. However, sponsor support may very well be a contingent liability to the sponsor and require disclosure by way of note to the balance sheet should consolidation not be required. CORPORATE FINANCE CONTRASTED A financing which is on credit or full recourse to the sponsor, whether it is directly borrowed or guaranteed by that sponsor, is a corporate financing. Lenders will tend to base their credit assessment on a historical assessment of the sponsor's activities and its financial results rather than an assessment of the project or a detailed assessment of the future activities and prospects of the sponsor. PROJECT FINANCE - A BORROWER'S PERCEPTION Although CRA could choose to arrange all finance on a corporate basis (except perhaps for the very largest projects or acquisitions), project financing techniques provide a number of specific advantages which CRA has noted and which should be carefully considered by a project sponsor. Advantages

Jan 1, 1985

By T. Sterry Hunt

It is now five years since I called the attention of the Institute to the industrial importance of the coal and the iron ores of the Hocking Valley in Southeastern Ohio, and in a pamphlet on the region published soon after, in 1874, endeavored to resume the principal facts then known respecting it, including the observations of the geological survey of Ohio, made and published up to the time by Professors Andrews and Wormley, together with an estimate of the probable future of the region, and its relations to the coal and iron markets of the country. Since that time the labors of the Geological Survey have included a further study of the coal by Prof. Edward Orton, the results of which will be awaited with much interest. I may say from my knowledge of them, that while confirming the general conclusions of his predecessors, he has been enabled to add much to our knowledge as regards the correlation of the various members in different parts of the coal-field; and to show more clearly the positions and the importance of the ore-beds in the Hocking Valley region. The only ore mined in that vicinity previous to 1874, was below what is called the Great Vein or No. VI coal, and to the west of what is known as the Hocking Valley coal-field, and although experiments in a few furnaces in the State had shown that this coal could be used with advantage in iron-smelting there was not a single blast furnace within the field. My observations at that time, however, impressed me with the abundance of iron ore, not only below but above this important coal seam, and I then ventured to express the opinion that this region, from its cheap and easily mined smelting-coal, its native ores and limestones, and its geographical position and relations to the great markets of the West, and to the supply of rich iron-ores from Lake Superior, was destined at no distant time to become a great metallurgical centre, where iron could be made more cheaply than at any other equally accessible point in the country. The object of the present communication is to report progress, and to state how far my observations made in the region 1st month have justified the predictions of 1874. The five years which have elapsed have been, as all know, most unfavorable to the iron trade, and especially to new enterprises in untried regions, yet they have not passed without important industrial developments in the Hocking Valley, where not less than thirteen blast furnaces have been erected

Jan 1, 1879

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

By AIME AIME

ARGUMENTS and discussions were not lacking either Wednesday or Thursday mornings, when the geophysicists got together. The first session, under the chairmanship of Paul Weaver, was devoted largely to theoretical papers, except for the first one by F. W. Lee, which was a progress report. This speaker mentioned some of the high lights of geophysical exploration during the last year, such as the recently announced extension of the Rand gold fields through magnetic exploration, and the continued activity in the oil fields of this country. Even this brought forth some disagreements, Paul Weaver feeling that credit was being given geophysics where it was not due for the discovery of certain oil fields. In this criticism Everette DeGolyer concurred, and both agreed that geophysicists must lean over backward when it comes to taking credit for discoveries. The troublesome question of interpreting resistivity curves is always being aired, and Lynn G. Howell's paper, presented briefly by the chairman, served to clear up a moot point raised last year by M. King Hubbert's work. By use of Maxwell's theory of images the author calculated that the effect of a thin, conductive sheet placed perpendicularly across the middle of a four electrode system should bring the resistivity curve up to a figure equivalent to the resistivity of the surrounding medium, but no higher. Variations from this he explained as being due to dirt on the surface of the sheet. The difficult question of interpreting three-layer curves was tackled bravely in Thomas Manhart's paper, presented in abstract by S. F. Kelly. The author seems to be attaining some success through dividing three-layer curves into two approximation curves of the two-layer type.

Jan 1, 1933

By G. Hasenfus, M. Karmis, G. Goodman

Surf ace subsidence is rapidly becoming an important environmental consideration of active as well as abandoned mining operations. The damages attributed to this phenomenon have been witnessed in both rural and urban areas and include land settlement and fracturing, structural damages to surface buildings or facilities and disruption or contamination of ground water supplies. The problem of mining subsidence has gained considerable emphasis in the Appalachian coalfield. The increased mining activity over the past few years and the particular topographic conditions, lithologic and structural environment, mining methods and hydrological patterns are all factors which have contributed to specific subsidence characteristics in this region. The objective of this paper is to discuss and review the most widely accepted methods of subsidence prediction above longwall as well as partial extraction systems in Appalachia. These include an accurate and easy to apply empirical method, which has been developed entirely from field information pertaining to the Appalachian coalfield and incorporates both geometrical and geological information of the panel in question. The second method is a development of influence functions and is founded on the zone area approach. Both methods, originally derived for longwall mining, have been expanded to include room and pillar applications and have been widely used by the mining industry in the Appalachian coalfield.

Jan 1, 1984

Both drilling and production in Rumania showed increases in 1934 over 1933. The drilling totaled 1,138,000 ft. and production 63,500,-000 bbl., being increases of 50 and 15 per cent, respectively. During the year production gradually increased from 155,000 bbl. per day in January to 180,000 bbl. in September, and then declined slightly to the end of the year. The increases were largely due to competitive drilling in the Gura Ocnitei field (including west extension to Viforata). Wells completed during the year totaled 238, of which 215 were oil producers. The outstanding development of the year was the discovery by Steaua Romana of what appears to be a major field at Bucsani. Other important discoveries were a three-mile west extension of the Gura Ocnitei fault to Viforata and a five-mile east extension of the Moreni field to Calinesti. Strictly speaking, the latter cannot as yet be called an extension. Oil sands have been corded in the Meotic, and in all probability production will be established in 1935. The Calinesti discovery greatly restricts the unproved area between Moreni and Baicoi, and the probabilities of

Jan 1, 1935

By J. Wayne Erickson

Hundreds of millions of dollars have been spent to discover or purchase uranium resources that cannot, or should not, be mined with conventional methods if human, natural and financial resources are to be conserved. Three years ago, an industry-supported research stud was initiated to determine whether a safer and more efficient (in terms of cost and environment) uranium mining method could be designed to replace existing techniques. As a result of this study, the "underground in situ" method was conceived and developed to the stage where it is now feasible. This approach involves: (1) sinking a shaft; (2) driving a drift on the ore horizon the length of the ore body; (3) drilling almost-horizontal long holes the width of the ore body; and (4) oxidizing and leaching the uranium drawn from these holes. The method is unique in that the uranium is removed with a minimum of disturbance to the natural hydrology of host or surrounding sands.

Jan 11, 1978

To the members of the A. I. M. E., who have given much and risked all to fight "Over There" with pick, or gun, or brain, and to the members who have chosen the sometimes more self-denying duty of remaining at home to help produce metals for fighters: Your experience in foreign lands has bred in you that spirit of internationalism which will soon be infused into every corner of our country by virile lads thrilling from a great experience in an old, yet new, land over the seas. To them the East will not seem as far from the West as it was, nor the North from the South. Sectional jealousies will seen despicable to one who has fought for a great ideal shoulder to shoulder with real men of other nations. And they who have willingly sacrificed much on the altar of service will have little patience with an egotist, be he laborer, tradesman, capitalist or engineer. The problems which peace brings to us are more difficult than those of war and their solution requires not only cool heads, tolerance, and wise judgment, but the "getting together" of sections and classes and individuals. The triumph of justice over individualism, represented by the draft law, must be repeated, for there are "slackers" in peace Is well as in war, and the spirit of self-denial expressed in response to Liberty Loans, Red Cross, and Welfare drives and Food Administration appeals must live. We have only just begun to learn how to serve. It is often claimed by our members that the engineer is not given, in the community at large, the recognition which his training should merit; that his reward is not as great nor his service as welcome as it should be. Public service is generally assumed to be a logical activity for a lawyer,

Jan 12, 1918

By S. A. Hovanessian

Analytical solutions are obtained for calculating the pressure distribution in rectangular fields due to injection and/or producing wells located anywhere within the field. The field is assumed to be homogeneous with either constant pressure or no-flow boundaries. These solutions are extended to include the calculation of average reservoir pressure and permeability from pressure build-up curves. Numerical examples are given to illustrate the application of equations to practical problems. INTRODUCTION Pressure distribution analyses are of considerable importance in the field of reservoir mechanics. A number of papers dealing with this subject have appeared in the petroleum literature. perrinel in 1956 presented a summary of the methods available for pressure build-up calculations and discussed the applicability of each in some detail. More recently (1958), Hazebroek, et a1,2 discussed a theoretical method for obtaining pressure distribution in a radial field. Also in 1958, Nisle3 gave a theoretical solution of the pressure distribution in a field extending to infinity with a partially penetrating line source at the origin. Mathews, et a1,4 applied the method of images to existing solutions for pressure distribution in radial fields and obtained expressions for calculating pressures in bounded reservoirs. However, a literature survey revealed that a general analytical solution for the pressure distribution in a rectangular field, with injection and/or production wells located anywhere within the field, was not available. Such a solution could be used to approximate the pressure distribution in a field the shape of which is nearly rectangular. Furthermore, it could be applied to pressure calculations pertaining to a single well taken from a system of wells which were drilled in a rectangular pattern. In this case the boundaries of the well drainage area are considered to be the perpendicular bisectors of the lines joining the well and its nearest neighbors. The basic problem considered in this paper consists of a rectangular field with either constant-pressure 01 no-flow boundaries and with either an injection or production well located anywhere within the field. The physical properties of the rock and fluids present are considered to be constant. Analytical expressions are obtained for the pressure distribution within the field during the production or injection periods. These expressions, which are infinite series, can be used to evaluate pressure at any point within the field as a function of time and position. For fields containing more than one well (production and/or injection), the solutions for each well acting independently are superposed. That is, at any point in the field, the pressures due to each injection 01. production well acting alone can be algebraically added to give the pressure resulting from all wells acting simultaneously. Evaluation of the series solutions given in this paper is readily accomplished by means of an electronic digital computer; and, in most cases, sufficient accuracy is obtained by setting the upper limits of summation at 20. These solutions are extended to include the calculation of average reservoir pressure and permeability from build-up data. A number of numerical examples are given to illustrate application of the solutions to actual field problems. ANALYTICAL SOLUTIONS The partial differential equation representing the pressure distribution in a homogeneous rectangular field (see Fig. I.), having a single source or sink of strength (2, can be written*

By E. J. Bruderlin

A metallurgical process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the distillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working blóck must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retorting plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties. Amarillo Silicon Carbide Retorts At the Amarillo plant of the American Smelting and Refining Co. a retort made of a suitable plastic clay grogged with silicon carbide has been found to best meet the present-day requirements. Retorts of this kind have been in use at Amarillo for 8 years and have shown an average furnace life of approximately 175 calendar days. The Amarillo retort is cylindrical in shape and after burning is approximately 83/4 in, inside diameter by 60 in. over-all length. The wall thickness is 136 in., except for the butt of the retort, which is approximately 2½ in. thick. The retort mud has a shrinkage of 3 per cent, or approximately % in. per foot. The silicon carbide retort after being properly dried weighs about 211 lb. When the retort is fired and ready to go into use the weight decreases to approximately 203 lb.

Jan 1, 1937

By Ernest Robinson

SINCE the early nineties, there has been a persistent belief in some minds that petroleum in commercial quantities exists in Montana. It is, however, only comparatively recently that commercial produc-tion has been secured. . The earliest deep boring in the plains region of Montana was made in what is now Blaine County, in 1890, by the town of Chinook in an effort to secure artesian water. The well reached a depth of 956 ft. without developing an adequate supply of fresh water, but the drillers reported shows of oil and gas. In 1892, the Quartermaster's Depart-ment of the U. S. Army drilled a hole at Fort Assini-boine, northwest of the Bearpaw Mountains, in essentially flat-lying sediments to secure water for the military establishment. This well reached a depth of 1500 ft. and shows of oil and gas were reported. In 1903 and 1904, two wells were drilled within what is now the Glacier National Park in an effort to develop oil production. Shows of oil and gas were encountered at several horizons but no commercial production was brought in. The extraordinary geological conditions in the area where these wells were drilled should be mentioned. The thrusts from the southwest which, in other places along the Rocky Mountain front, resulted in folding, here developed the great Lewis overthrust fault. It is in fact largely to this fault that the magnificent scenery of the Glacier Park is due. A great thickness of Algonkian strata belonging to the Belt series was thrust northeastward over the upper Cretaceous sediments. The derricks under which the wells referred to were drilled were in moun-tains composed of very old rocks but the holes were drilled through Cretaceous sediments.

Jan 7, 1923

By W. H. Fitch

HAVING been asked to make some remarks after the reading of Mr. Dyrssen's paper, I regret that a test started some months ago has not yet been completed, but some of the things which I can tell you at this time seem interesting and shed a little different light on the idea of a recuperator. The device referred to is becoming more than. a recuperator, largely taking the place of a regenerator. I assume there is familiarity with the sketches that I presented in October, 1926, before the Engineers' Society of Western Pennsylvania, describing our re-cuperator combination with checker chambers, and I have additional ones to show at this time. The follow-ing remarks will deal with modifications that have been made. At that time I suggested the gases leaving the regenerators at, say, 1400°, be reduced to 500° F. The opinion of the operating men consulted since that time is that, under the best operating conditions, the tem-perature may be 750° to 800° F. after the recuperator and on entering the stack. While the lowest final temperature of the gases en-tering the stack is important from the economic stand-point of fuel burning, and operating in general, it is not the whole story. The method of getting the heat out of the checkers is important. It is believed by many with whom we have talked that a better way is by a combination of checkers and a carborundum re- cuperator of the type described as it will stand all tem-peratures met in practice and might be called a super-refractory.

Jan 1, 1928

By D. J. Carney, J. Chipman, N. J. Grant

G. Derge—With the development of this last weapon, there is not much of a chance for hydrogen. It is certainly a very interesting paper, and it gives us more confidence in sampling liquid steel for hydrogen than we have ever had before. This satisfactory work gives considerable confidence to all of the chilled methods of sampling which should be more or less successful depending upon the degree of chilling obtained. J. T. MacKenzie—How do you handle a nonmagnetic specimen in that device? D. J. Carney (authors' reply)—I left that out in going over the analytical procedure. For the 18-8 steel, what was done was to get some iron wire which was degassed. One turn of wire was made around the sample; it was inserted into the analytical apparatus, and that was enough to allow the magnet to pull the sample and drop it in the furnace. Other methods could be devised for this apparatus to do the same thing. This was just a quick method. C. E. Sims—This method of sampling and analysis is very ingenious, and the results obtained attest to a satisfactory degree of accuracy. It was noted in the paper that the samples are satisfactory only when there is a complete absence of pipe. This should be empha- sized, particularly in view of the fact that they are cut off under water. Some reservations are held in regard to the adequacy of the method of sample storage prior to analysis. Cooling on dry ice undoubtedly slows down the rate of diffusion to a marked degree, and it obviously suffices when the analysis is made within a few hours. All of the samples, except some of high-nickel steels, were analyzed within 12 hr. It is still unknown how long this method would be safe. In the work at Battelle Institute, it was impracticable always to start analysis within 12 hr for various reasons. Some samples did not reach the laboratory for several days, and some were held as long as a month before analysis. During this period, they were held over mercury, and the gas evolved at room temperature was collected and analyzed. It should be mentioned that both the mercury and the container must be kept very clean.

Jan 1, 1951

Jan 1, 1919